|
On 01/22/2015 10:03 PM, Ritesh Raj
Sarraf wrote:
Well. On boot, on this iteration, the driver wasn't even loaded. Which led to no wireless interface in the OS. Manually re-plugging the device again, raised the event and the proper driver was loaded. And now, on suspend/resume, the device is dead. I just hope that it is a driver issue. Because if otherwise, I'm not sure what expectations can be set with this device. The only other option I can think of is to reboot into Windows to check if it behaves properly there. [ 3171.053462] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 3171.053673] usb 1-13: reset full-speed USB device number 3 using xhci_hcd [ 3171.053755] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2. [ 3171.053757] usb 1-13: hub failed to enable device, error -22 [ 3171.054374] ata1.00: configured for UDMA/100 [ 3171.165658] usb 1-13: reset full-speed USB device number 3 using xhci_hcd [ 3171.165696] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 2. [ 3171.165697] usb 1-13: hub failed to enable device, error -22 [ 3171.277749] usb 1-13: reset full-speed USB device number 3 using xhci_hcd [ 3171.294391] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880250d12040 [ 3171.405852] usb 1-14: reset full-speed USB device number 4 using xhci_hcd [ 3171.405875] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3. [ 3171.405877] usb 1-14: hub failed to enable device, error -22 [ 3171.517812] usb 1-14: reset full-speed USB device number 4 using xhci_hcd [ 3171.517841] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 3. [ 3171.517842] usb 1-14: hub failed to enable device, error -22 [ 3171.629898] usb 1-14: reset full-speed USB device number 4 using xhci_hcd [ 3171.646699] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88009ad8dc00 [ 3171.646700] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88009ad8dc48 [ 3171.646701] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88009ad8dc90 [ 3171.646702] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88009ad8dcd8 [ 3171.758120] usb 1-7: reset high-speed USB device number 2 using xhci_hcd [ 3171.758153] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1. [ 3171.758154] usb 1-7: hub failed to enable device, error -22 [ 3171.870106] usb 1-7: reset high-speed USB device number 2 using xhci_hcd [ 3171.870125] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1. [ 3171.870126] usb 1-7: hub failed to enable device, error -22 [ 3171.982192] usb 1-7: reset high-speed USB device number 2 using xhci_hcd [ 3172.040684] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88025407ba40 [ 3172.166496] usb 1-3: reset high-speed USB device number 5 using xhci_hcd [ 3172.166509] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4. [ 3172.166511] usb 1-3: hub failed to enable device, error -22 [ 3172.278501] usb 1-3: reset high-speed USB device number 5 using xhci_hcd [ 3172.278514] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 4. [ 3172.278515] usb 1-3: hub failed to enable device, error -22 [ 3172.350513] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off [ 3172.390560] usb 1-3: reset high-speed USB device number 5 using xhci_hcd [ 3172.390622] usb 1-3: Device not responding to setup address. [ 3172.594720] usb 1-3: Device not responding to setup address. [ 3172.798824] usb 1-3: device not accepting address 5, error -71 [ 3172.910974] usb 1-3: reset high-speed USB device number 5 using xhci_hcd [ 3172.911036] usb 1-3: Device not responding to setup address. [ 3173.115141] usb 1-3: Device not responding to setup address. [ 3173.319245] usb 1-3: device not accepting address 5, error -71 [ 3173.319366] PM: resume of devices complete after 2583.482 msecs [ 3173.319579] PM: Finishing wakeup. [ 3173.319580] Restarting tasks ... [ 3173.319636] rt2800pci 0000:07:00.0: no hotplug settings from platform [ 3173.319646] pci 0000:07:00.1: no hotplug settings from platform [ 3173.319656] usb 1-3: USB disconnect, device number 5 [ 3173.319743] pci 0000:09:00.0: [10ec:5227] type 00 class 0xff0000 [ 3173.319751] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880218bdae00 [ 3173.319754] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880218bdae48 [ 3173.319756] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880218bdae90 [ 3173.319758] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff880218bdaed8 [ 3173.319814] pci 0000:09:00.0: reg 0x10: [mem 0x00000000-0x00000fff] [ 3173.320148] pci 0000:09:00.0: supports D1 D2 [ 3173.320150] pci 0000:09:00.0: PME# supported from D1 D2 D3hot D3cold [ 3173.320242] pci 0000:09:00.0: System wakeup disabled by ACPI [ 3173.330986] pci 0000:09:00.0: BAR 0: assigned [mem 0xd1000000-0xd1000fff] [ 3173.331064] pci 0000:09:00.0: no hotplug settings from platform [ 3173.331326] r8169 0000:0f:00.0: no hotplug settings from platform [ 3173.338340] cfg80211: World regulatory domain updated: [ 3173.338345] cfg80211: DFS Master region: unset [ 3173.338346] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 3173.338349] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 3173.338351] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 3173.338352] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 3173.338355] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 3173.338357] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 3173.338359] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 3173.338361] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 3173.338363] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 3173.338965] done. [ 3173.435461] usb 1-3: new high-speed USB device number 6 using xhci_hcd [ 3173.547470] usb 1-3: device descriptor read/64, error -71 [ 3173.651532] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 5. [ 3173.651537] usb 1-3: hub failed to enable device, error -22 [ 3173.763656] usb 1-3: new high-speed USB device number 7 using xhci_hcd [ 3173.875797] usb 1-3: device descriptor read/64, error -71 [ 3173.979814] xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 6. [ 3173.979818] usb 1-3: hub failed to enable device, error -22 [ 3174.091916] usb 1-3: new high-speed USB device number 8 using xhci_hcd [ 3174.091995] usb 1-3: Device not responding to setup address. [ 3174.296121] usb 1-3: Device not responding to setup address. [ 3174.472438] wlan0: authenticate with 00:03:7f:fe:00:02 [ 3174.488260] wlan0: send auth to 00:03:7f:fe:00:02 (try 1/3) [ 3174.494697] wlan0: authenticated [ 3174.496246] wlan0: associate with 00:03:7f:fe:00:02 (try 1/3) [ 3174.500247] usb 1-3: device not accepting address 8, error -71 [ 3174.500545] wlan0: RX AssocResp from 00:03:7f:fe:00:02 (capab=0x411 status=0 aid=2) [ 3174.500618] wlan0: associated [ 3174.612358] usb 1-3: new high-speed USB device number 9 using xhci_hcd [ 3174.612459] usb 1-3: Device not responding to setup address. [ 3174.741442] rtsx_pci 0000:09:00.0: enabling device (0000 -> 0002) [ 3174.741608] rtsx_pci 0000:09:00.0: irq 49 for MSI/MSI-X [ 3174.741638] rtsx_pci 0000:09:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 49 [ 3174.816588] usb 1-3: Device not responding to setup address. [ 3175.020626] usb 1-3: device not accepting address 9, error -71 [ 3175.020671] usb usb1-port3: unable to enumerate USB device [ 3176.155635] wlan0: deauthenticating from 00:03:7f:fe:00:02 by local choice (Reason: 3=DEAUTH_LEAVING) [ 3176.178960] cfg80211: Calling CRDA to update world regulatory domain [ 3176.180645] cfg80211: World regulatory domain updated: [ 3176.180648] cfg80211: DFS Master region: unset [ 3176.180649] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 3176.180650] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 3176.180651] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 3176.180652] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 3176.180654] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 3176.180655] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 3176.180656] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 3176.180657] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 3176.180658] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 3176.225873] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3176.532012] r8169 0000:0f:00.0 eth0: link down [ 3176.532076] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3178.391457] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95) [ 3178.391550] ACPI: \_SB_.PCI0.PEG0.PEGP: failed to evaluate _DSM [ 3178.391553] ACPI Warning: \_SB_.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20140424/nsarguments-95) [ 3178.643793] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3179.964852] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3180.166921] r8169 0000:0f:00.0 eth0: link down [ 3180.166987] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 3180.305149] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3182.418901] wlan0: authenticate with 00:03:7f:fe:00:02 [ 3182.426717] wlan0: send auth to 00:03:7f:fe:00:02 (try 1/3) [ 3182.428732] wlan0: authenticated [ 3182.430632] wlan0: associate with 00:03:7f:fe:00:02 (try 1/3) [ 3182.432798] wlan0: RX AssocResp from 00:03:7f:fe:00:02 (capab=0x411 status=0 aid=2) [ 3182.432877] wlan0: associated [ 3182.432894] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready -- Ritesh Raj Sarraf RESEARCHUT - http://www.researchut.com "Necessity is the mother of invention." |
Attachment:
signature.asc
Description: OpenPGP digital signature