Bug#789039: strange error messages after upgrade to linux-image-2.6.32-5-686 2.6.32-48squeeze12
Package: linux-2.6
Version: 2.6.32-48squeeze11
Severity: critical
Justification: breaks the whole system
Hi,
After upgrade
linux-image-2.6.32-5-686 2.6.32-48squeeze11 -> 2.6.32-48squeeze12
I get a lot of dmesg messages like
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.142021] EIP: [<c120e115>] tcp_send_fin+0x2f/0x16a SS:ESP
0068:ef4e3f30
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.142021] CR2: 0000000000000044
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.820539] Oops: 0002 [#2535] SMP
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.820539] last sysfs file: /sys/module/thermal/initstate
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.823772] Process nrpe (pid: 18418, ti=ef4fc000
task=f3233300 task.ti=ef4fc000)
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.823772] Stack:
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.823772] Call Trace:
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.823772] Code: c6 8d a8 80 00 00 00 b8 00 00 00 00
53 8b 7d 04 39 ef 0f 44 f8 85 ff 74 3a 83 be 50 01 00 00 00 75
09 83 3d 70 dd 3b c1 00 74 28 <80> 0d 44 00 00 00 01 ff 47 3c ff
86 d4 03 00 00 83 be 50 01 00
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.823772] EIP: [<c120e115>] tcp_send_fin+0x2f/0x16a
SS:ESP 0068:ef4fdf30
Message from syslogd@prodserver at Jun 17 12:16:17 ...
kernel:[13563.823772] CR2: 0000000000000044
Message from syslogd@prodserver at Jun 17 12:16:18 ...
kernel:[13563.843171] Oops: 0002 [#2536] SMP
Message from syslogd@prodserver at Jun 17 12:16:18 ...
kernel:[13563.843309] last sysfs file:
/sys/module/thermal/initstate
Message from syslogd@prodserver at Jun 17 12:16:18 ...
kernel:[13563.846121] Process nrpe (pid: 18420, ti=ef434000
task=f324a640 task.ti=ef434000)
Message from syslogd@prodserver at Jun 17 12:16:18 ...
kernel:[13563.846121] Stack:
Message from syslogd@prodserver at Jun 17 12:16:18 ...
kernel:[13563.846121] Call Trace:
Message from syslogd@prodserver at Jun 17 12:16:18 ...
kernel:[13563.846121] Code: c6 8d a8 80 00 00 00 b8 00
00 00 00 53 8b 7d 04 39 ef 0f 44 f8 85 ff 74 3a 83 be 50
01 00 00 00 75 09 83 3d 70 dd 3b c1 00 74 28 <80> 0d 44
00 00 00 01 ff 47 3c ff 86 d4 03 00 00 83 be 50 01 00
Message from syslogd@prodserver at Jun 17 12:16:18 ...
kernel:[13563.846121] EIP: [<c120e115>]
tcp_send_fin+0x2f/0x16a SS:ESP 0068:ef435f30
After reinstall the old kernel everything went fine again.
I had this issue on 3 Servers
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-48squeeze11) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed Feb 18 13:24:13 UTC 2015
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=UUID=d39f5d77-b580-4bd7-8811-0d37b6ca7006 ro quiet
** Model information
not available
** Loaded modules:
Module Size Used by
xt_multiport 1775 1
iptable_filter 1790 1
ip_tables 7706 1 iptable_filter
x_tables 8327 2 xt_multiport,ip_tables
nfsd 193439 2
exportfs 2598 1 nfsd
nfs 206842 6
lockd 49361 2 nfsd,nfs
fscache 24506 1 nfs
nfs_acl 1695 2 nfsd,nfs
auth_rpcgss 25252 2 nfsd,nfs
sunrpc 134615 26 nfsd,nfs,lockd,nfs_acl,auth_rpcgss
ext3 94204 1
jbd 32409 1 ext3
loop 9745 0
shpchp 21200 0
pci_hotplug 18545 1 shpchp
container 1833 0
parport_pc 15799 0
snd_pcm 47226 0
snd_timer 12270 1 snd_pcm
snd 34631 2 snd_pcm,snd_timer
soundcore 3450 1 snd
snd_page_alloc 5001 1 snd_pcm
intel_rng 1965 0
evdev 5609 2
rng_core 2178 1 intel_rng
parport 22554 1 parport_pc
e7xxx_edac 2876 0
button 3598 0
edac_core 23121 3 e7xxx_edac
processor 26291 0
pcspkr 1207 0
serio_raw 2916 0
i2c_i801 6462 0
i2c_core 12763 1 i2c_i801
ext4 256917 2
mbcache 3762 2 ext3,ext4
jbd2 56091 1 ext4
crc16 1027 1 ext4
raid1 16351 4
md_mod 67385 5 raid1
sd_mod 25969 10
crc_t10dif 1012 1 sd_mod
ata_generic 2247 0
e100 22253 0
sata_promise 7313 10
ata_piix 17716 0
e1000 77205 0
floppy 41027 0
uhci_hcd 16013 0
mii 2714 1 e100
thermal 9206 0
libata 115721 3 ata_generic,sata_promise,ata_piix
ehci_hcd 28513 0
scsi_mod 104961 2 sd_mod,libata
usbcore 99350 3 uhci_hcd,ehci_hcd
nls_base 4727 1 usbcore
thermal_sys 9378 2 processor,thermal
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation E7501 Memory Controller Hub [8086:254c] (rev 01)
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: e7xxx_edac
00:00.1 Unassigned class [ff00]: Intel Corporation E7500/E7501 Host RASUM Controller [8086:2541] (rev 01)
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:02.0 PCI bridge [0604]: Intel Corporation E7500/E7501 Hub Interface B PCI-to-PCI Bridge [8086:2543] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=03, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: fc100000-fc2fffff
Prefetchable memory behind bridge: c0000000-c00fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1d.0 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #1 [8086:2482] (rev 02) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 2000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #2 [8086:2484] (rev 02) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 2020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801CA/CAM USB Controller #3 [8086:2487] (rev 02) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 2040 [size=32]
Kernel driver in use: uhci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 42) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
I/O behind bridge: 00004000-00004fff
Memory behind bridge: fc300000-fdffffff
Prefetchable memory behind bridge: c0100000-c01fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801CA LPC Interface Controller [8086:2480] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801CA Ultra ATA Storage Controller [8086:248b] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 2060 [size=16]
Region 5: Memory at c0200000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801CA/CAM SMBus Controller [8086:2483] (rev 02)
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 1100 [size=32]
Kernel driver in use: i801_smbus
01:1c.0 PIC [0800]: Intel Corporation 82870P2 P64H2 I/OxAPIC [8086:1461] (rev 04) (prog-if 20 [IO(X)-APIC])
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fc100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
01:1d.0 PCI bridge [0604]: Intel Corporation 82870P2 P64H2 Hub PCI Bridge [8086:1460] (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=01, secondary=02, subordinate=02, sec-latency=48
I/O behind bridge: 00003000-00003fff
Memory behind bridge: fc200000-fc2fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c00fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
01:1e.0 PIC [0800]: Intel Corporation 82870P2 P64H2 I/OxAPIC [8086:1461] (rev 04) (prog-if 20 [IO(X)-APIC])
Subsystem: Super Micro Computer Inc Device [15d9:3980]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at fc101000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
01:1f.0 PCI bridge [0604]: Intel Corporation 82870P2 P64H2 Hub PCI Bridge [8086:1460] (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=01, secondary=03, subordinate=03, sec-latency=64
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort+ >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
02:01.0 Mass storage controller [0180]: Promise Technology, Inc. PDC40775 (SATA 300 TX2plus) [105a:3d73] (rev 02)
Subsystem: Promise Technology, Inc. PDC40775 (SATA 300 TX2plus) [105a:3d73]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 72 (1000ns min, 4500ns max), Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 48
Region 0: I/O ports at 3400 [size=128]
Region 2: I/O ports at 3000 [size=256]
Region 3: Memory at fc240000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at fc200000 (32-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at c0000000 [disabled] [size=32K]
Capabilities: <access denied>
Kernel driver in use: sata_promise
02:03.0 Ethernet controller [0200]: Intel Corporation 82545EM Gigabit Ethernet Controller (Copper) [8086:100f] (rev 01)
Subsystem: Intel Corporation Device [8086:1011]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (63750ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 54
Region 0: Memory at fc220000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at 3480 [size=64]
Capabilities: <access denied>
Kernel driver in use: e1000
04:04.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL [1002:4752] (rev 27) (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc Rage XL [1002:0008]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 4000 [size=256]
Region 2: Memory at fc300000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at c0100000 [disabled] [size=128K]
Capabilities: <access denied>
04:05.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 10)
Subsystem: Intel Corporation EtherExpress PRO/100 S Server Adapter [8086:1050]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fc301000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 4400 [size=64]
Region 2: Memory at fc320000 (32-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at c0120000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: e100
** USB devices:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 6.0.10
APT prefers squeeze-lts
APT policy: (500, 'squeeze-lts'), (500, 'oldoldstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Reply to: