[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#777683: linux-image-3.16.0-0.bpo.4-686-pae: high package loss and data corruption with e1000e driver



Package: src:linux
Version: 3.16.7-ckt2-1~bpo70+1
Severity: important

Dear Maintainer,

after switching to kernel 3.16 from backports network packets
over the on-board ethernet controller (Intel Corporation 82566DM
Gigabit Network Connection, driver e1000e) are only transferred
in bursts, transfer rates are below 1 MB/s, packet loss is at 70
to 80%, transferred files are corrupted and I get a lot of kernel
errors (see below).
Switching back to kernel linux-image-3.2.0-4-686-pae fixes the
problem.

Regards

Uwe


-- Package-specific info:
** Kernel log: boot messages should be attached
Feb 11 05:05:02 c1 kernel: [4667586.001612] e1000e 0000:00:19.0 lan: Detected Hardware Unit Hang:
Feb 11 05:05:02 c1 kernel: [4667586.001612]   TDH                  <ab>
Feb 11 05:05:02 c1 kernel: [4667586.001612]   TDT                  <11>
Feb 11 05:05:02 c1 kernel: [4667586.001612]   next_to_use          <11>
Feb 11 05:05:02 c1 kernel: [4667586.001612]   next_to_clean        <ab>
Feb 11 05:05:02 c1 kernel: [4667586.001612] buffer_info[next_to_clean]:
Feb 11 05:05:02 c1 kernel: [4667586.001612]   time_stamp           <458c46a8>
Feb 11 05:05:02 c1 kernel: [4667586.001612]   next_to_watch        <b0>
Feb 11 05:05:02 c1 kernel: [4667586.001612]   jiffies              <458c487d>
Feb 11 05:05:02 c1 kernel: [4667586.001612]   next_to_watch.status <0>
Feb 11 05:05:02 c1 kernel: [4667586.001612] MAC Status             <802a3>
Feb 11 05:05:02 c1 kernel: [4667586.001612] PHY Status             <792d>
Feb 11 05:05:02 c1 kernel: [4667586.001612] PHY 1000BASE-T Status  <3800>
Feb 11 05:05:02 c1 kernel: [4667586.001612] PHY Extended Status    <3000>
Feb 11 05:05:02 c1 kernel: [4667586.001612] PCI Status             <10>
Feb 11 05:05:04 c1 kernel: [4667588.001373] e1000e 0000:00:19.0 lan: Detected Hardware Unit Hang:
Feb 11 05:05:04 c1 kernel: [4667588.001373]   TDH                  <ab>
Feb 11 05:05:04 c1 kernel: [4667588.001373]   TDT                  <11>
Feb 11 05:05:04 c1 kernel: [4667588.001373]   next_to_use          <11>
Feb 11 05:05:04 c1 kernel: [4667588.001373]   next_to_clean        <ab>
Feb 11 05:05:04 c1 kernel: [4667588.001373] buffer_info[next_to_clean]:
Feb 11 05:05:04 c1 kernel: [4667588.001373]   time_stamp           <458c46a8>
Feb 11 05:05:04 c1 kernel: [4667588.001373]   next_to_watch        <b0>
Feb 11 05:05:04 c1 kernel: [4667588.001373]   jiffies              <458c4a71>
Feb 11 05:05:04 c1 kernel: [4667588.001373]   next_to_watch.status <0>
Feb 11 05:05:04 c1 kernel: [4667588.001373] MAC Status             <802a3>
Feb 11 05:05:04 c1 kernel: [4667588.001373] PHY Status             <792d>
Feb 11 05:05:04 c1 kernel: [4667588.001373] PHY 1000BASE-T Status  <3800>
Feb 11 05:05:04 c1 kernel: [4667588.001373] PHY Extended Status    <3000>
Feb 11 05:05:04 c1 kernel: [4667588.001373] PCI Status             <10>
Feb 11 05:05:06 c1 kernel: [4667590.000645] e1000e 0000:00:19.0 lan: Detected Hardware Unit Hang:
Feb 11 05:05:06 c1 kernel: [4667590.000645]   TDH                  <ab>
Feb 11 05:05:06 c1 kernel: [4667590.000645]   TDT                  <11>
Feb 11 05:05:06 c1 kernel: [4667590.000645]   next_to_use          <11>
Feb 11 05:05:06 c1 kernel: [4667590.000645]   next_to_clean        <ab>
Feb 11 05:05:06 c1 kernel: [4667590.000645] buffer_info[next_to_clean]:
Feb 11 05:05:06 c1 kernel: [4667590.000645]   time_stamp           <458c46a8>
Feb 11 05:05:06 c1 kernel: [4667590.000645]   next_to_watch        <b0>
Feb 11 05:05:06 c1 kernel: [4667590.000645]   jiffies              <458c4c65>
Feb 11 05:05:06 c1 kernel: [4667590.000645]   next_to_watch.status <0>
Feb 11 05:05:06 c1 kernel: [4667590.000645] MAC Status             <802a3>
Feb 11 05:05:06 c1 kernel: [4667590.000645] PHY Status             <792d>
Feb 11 05:05:06 c1 kernel: [4667590.000645] PHY 1000BASE-T Status  <3800>
Feb 11 05:05:06 c1 kernel: [4667590.000645] PHY Extended Status    <3000>
Feb 11 05:05:06 c1 kernel: [4667590.000645] PCI Status             <10>
Feb 11 05:05:08 c1 kernel: [4667592.000580] e1000e 0000:00:19.0 lan: Detected Hardware Unit Hang:
Feb 11 05:05:08 c1 kernel: [4667592.000580]   TDH                  <ab>
Feb 11 05:05:08 c1 kernel: [4667592.000580]   TDT                  <11>
Feb 11 05:05:08 c1 kernel: [4667592.000580]   next_to_use          <11>
Feb 11 05:05:08 c1 kernel: [4667592.000580]   next_to_clean        <ab>
Feb 11 05:05:08 c1 kernel: [4667592.000580] buffer_info[next_to_clean]:
Feb 11 05:05:08 c1 kernel: [4667592.000580]   time_stamp           <458c46a8>
Feb 11 05:05:08 c1 kernel: [4667592.000580]   next_to_watch        <b0>
Feb 11 05:05:08 c1 kernel: [4667592.000580]   jiffies              <458c4e59>
Feb 11 05:05:08 c1 kernel: [4667592.000580]   next_to_watch.status <0>
Feb 11 05:05:08 c1 kernel: [4667592.000580] MAC Status             <802a3>
Feb 11 05:05:08 c1 kernel: [4667592.000580] PHY Status             <792d>
Feb 11 05:05:08 c1 kernel: [4667592.000580] PHY 1000BASE-T Status  <3800>
Feb 11 05:05:08 c1 kernel: [4667592.000580] PHY Extended Status    <3000>
Feb 11 05:05:08 c1 kernel: [4667592.000580] PCI Status             <10>
Feb 11 05:05:08 c1 kernel: [4667592.013550] e1000e 0000:00:19.0 lan: Reset adapter unexpectedly
Feb 11 05:05:11 c1 kernel: [4667594.823364] e1000e: lan NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

** Model information
HP Compaq dc7700p Convertible Minitower

** Network interface configuration:

auto lan
iface lan inet static
	address 172.18.1.1
	network 172.18.1.0
	netmask 255.255.255.128
	broadcast 172.18.1.127

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82Q963/Q965 Memory Controller Hub [8086:2990] (rev 02)
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>
	Kernel driver in use: agpgart-intel

00:02.0 VGA compatible controller [0300]: Intel Corporation 82Q963/Q965 Integrated Graphics Controller [8086:2992] (rev 02) (prog-if 00 [VGA controller])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 42
	Region 0: Memory at f0400000 (32-bit, non-prefetchable) [size=1M]
	Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
	Region 4: I/O ports at 2110 [size=8]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: i915

00:03.0 Communication controller [0780]: Intel Corporation 82Q963/Q965 HECI Controller [8086:2994] (rev 02)
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
	Latency: 0
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at f0526900 (64-bit, non-prefetchable) [size=16]
	Capabilities: <access denied>

00:03.2 IDE interface [0101]: Intel Corporation 82Q963/Q965 PT IDER Controller [8086:2996] (rev 02) (prog-if 85 [Master SecO PriO])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 18
	Region 0: I/O ports at 2118 [size=8]
	Region 1: I/O ports at 2140 [size=4]
	Region 2: I/O ports at 2120 [size=8]
	Region 3: I/O ports at 2144 [size=4]
	Region 4: I/O ports at 20e0 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_generic

00:03.3 Serial controller [0700]: Intel Corporation 82Q963/Q965 KT Controller [8086:2997] (rev 02) (prog-if 02 [16550])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at 2128 [size=8]
	Region 1: Memory at f0524000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: serial

00:19.0 Ethernet controller [0200]: Intel Corporation 82566DM Gigabit Network Connection [8086:104a] (rev 02)
	Subsystem: Hewlett-Packard Company Device [103c:2800]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 41
	Region 0: Memory at f0500000 (32-bit, non-prefetchable) [size=128K]
	Region 1: Memory at f0525000 (32-bit, non-prefetchable) [size=4K]
	Region 2: I/O ports at 2000 [size=32]
	Capabilities: <access denied>
	Kernel driver in use: e1000e

00:1a.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 20
	Region 4: I/O ports at 2020 [size=32]
	Kernel driver in use: uhci_hcd

00:1a.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 21
	Region 4: I/O ports at 2040 [size=32]
	Kernel driver in use: uhci_hcd

00:1a.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 22
	Region 0: Memory at f0526000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
	Subsystem: Hewlett-Packard Company HP Compaq dc7700p [103c:2802]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 43
	Region 0: Memory at f0520000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: f8100000-f82fffff
	Prefetchable memory behind bridge: 00000000f8300000-00000000f84fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 20
	Region 4: I/O ports at 2060 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 21
	Region 4: I/O ports at 2080 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at f0526400 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev f2) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
	I/O behind bridge: 00001000-00001fff
	Memory behind bridge: f0600000-f08fffff
	Prefetchable memory behind bridge: 00000000f8000000-00000000f80fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 82801HO (ICH8DO) LPC Interface Controller [8086:2814] (rev 02)
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Capabilities: <access denied>

00:1f.2 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 4 port SATA Controller [IDE mode] [8086:2820] (rev 02) (prog-if 8a [Master SecP PriP])
	Subsystem: Hewlett-Packard Company Device [103c:2802]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 18
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at 20f0 [size=16]
	Region 5: I/O ports at 2100 [size=16]
	Capabilities: <access denied>
	Kernel driver in use: ata_piix

07:04.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet [14e4:1648] (rev 10)
	Subsystem: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet [14e4:1648]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (16000ns min), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 20
	Region 0: Memory at f0800000 (64-bit, non-prefetchable) [size=64K]
	[virtual] Expansion ROM at f8080000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: tg3

07:04.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet [14e4:1648] (rev 10)
	Subsystem: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet [14e4:1648]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (16000ns min), Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 21
	Region 0: Memory at f0810000 (64-bit, non-prefetchable) [size=64K]
	Expansion ROM at <ignored> [disabled]
	Capabilities: <access denied>
	Kernel driver in use: tg3

07:09.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller [1095:3512] (rev 01)
	Subsystem: Silicon Image, Inc. SiI 3512 SATARaid Controller [1095:6512]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at 1030 [size=8]
	Region 1: I/O ports at 1040 [size=4]
	Region 2: I/O ports at 1038 [size=8]
	Region 3: I/O ports at 1044 [size=4]
	Region 4: I/O ports at 1020 [size=16]
	Region 5: Memory at f0820000 (32-bit, non-prefetchable) [size=512]
	[virtual] Expansion ROM at f8000000 [disabled] [size=512K]
	Capabilities: <access denied>
	Kernel driver in use: sata_sil

07:0b.0 Network controller [0280]: AVM GmbH A1 ISDN [Fritz] [1244:0a00] (rev 02)
	Subsystem: AVM GmbH FRITZ!Card ISDN Controller [1244:0a00]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin A routed to IRQ 5
	Region 0: Memory at f0820200 (32-bit, non-prefetchable) [size=32]
	Region 1: I/O ports at 1000 [size=32]


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


-- System Information:
Debian Release: 7.8
  APT prefers stable
  APT policy: (850, 'stable'), (840, 'stable-updates')
Architecture: i386 (i686)

Kernel: Linux 3.2.0-4-686-pae (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-3.16.0-0.bpo.4-686-pae depends on:
ii  debconf [debconf-2.0]                   1.5.49
ii  initramfs-tools [linux-initramfs-tool]  0.115~bpo70+1
ii  kmod                                    9-3
ii  linux-base                              3.5

Versions of packages linux-image-3.16.0-0.bpo.4-686-pae recommends:
ii  firmware-linux-free  3.2
pn  irqbalance           <none>
ii  libc6-i686           2.13-38+deb7u7

Versions of packages linux-image-3.16.0-0.bpo.4-686-pae suggests:
pn  debian-kernel-handbook  <none>
ii  grub-pc                 1.99-27+deb7u2
pn  linux-doc-3.16          <none>

Versions of packages linux-image-3.16.0-0.bpo.4-686-pae is related to:
pn  firmware-atheros        <none>
pn  firmware-bnx2           <none>
pn  firmware-bnx2x          <none>
pn  firmware-brcm80211      <none>
pn  firmware-intelwimax     <none>
pn  firmware-ipw2x00        <none>
pn  firmware-ivtv           <none>
pn  firmware-iwlwifi        <none>
pn  firmware-libertas       <none>
pn  firmware-linux          <none>
ii  firmware-linux-nonfree  0.36+wheezy.1
pn  firmware-myricom        <none>
pn  firmware-netxen         <none>
pn  firmware-qlogic         <none>
pn  firmware-ralink         <none>
pn  firmware-realtek        <none>
pn  xen-hypervisor          <none>

-- debconf information:
  linux-image-3.16.0-0.bpo.4-686-pae/postinst/depmod-error-initrd-3.16.0-0.bpo.4-686-pae: false
  linux-image-3.16.0-0.bpo.4-686-pae/prerm/removing-running-kernel-3.16.0-0.bpo.4-686-pae: true
  linux-image-3.16.0-0.bpo.4-686-pae/postinst/mips-initrd-3.16.0-0.bpo.4-686-pae:


Reply to: