Bug#742055: linux-image-3.13-1-powerpc: please enable r8712u.ko as a module on powerpc
Package: src:linux
Version: 3.13.5-1
Severity: normal
I'm using a powerbook g4. In addition to the onboard wireless, I have
an ASUS USB-N10 NIC, which reports itself as:
Bus 002 Device 002: ID 0b05:1786 ASUSTek Computer, Inc. USB-N10 802.11n Network Adapter [Realtek RTL8188SU]
It does not work with the debian kernel because r8712u.ko is only
enabled as a module for x86, afaict.
0 dkg@tyr:/tmp$ grep 8712 /boot/config-3.13-1-powerpc
# CONFIG_R8712U is not set
0 dkg@tyr:/tmp$
Please enable this module for powerpc. thanks!
--dkg
-- Package-specific info:
** Version:
Linux version 3.13-1-powerpc (debian-kernel@lists.debian.org) (gcc version 4.8.2 (Debian 4.8.2-14) ) #1 Debian 3.13.5-1 (2014-03-04)
** Command line:
BOOT_IMAGE=/boot/vmlinux-3.13-1-powerpc root=/dev/mapper/vg_tyr0-root ro quiet radeon.modeset=1 video=radeonfb:off radeon.agpmode=1 init=/bin/systemd
** Not tainted
** Kernel log:
[ 1567.439429] gem 0002:24:0f.0 eth0: Link down
[ 2433.770153] wlan0: authenticate with 10:bd:18:3c:2a:a1
[ 2433.790848] wlan0: send auth to 10:bd:18:3c:2a:a1 (try 1/3)
[ 2433.792150] wlan0: authenticated
[ 2433.798738] wlan0: associate with 10:bd:18:3c:2a:a1 (try 1/3)
[ 2433.801618] wlan0: RX AssocResp from 10:bd:18:3c:2a:a1 (capab=0x431 status=0 aid=68)
[ 2433.801920] wlan0: associated
[ 2433.801976] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2433.802098] cfg80211: Calling CRDA for country: US
[ 2434.269406] cfg80211: Regulatory domain changed to country: US
[ 2434.269420] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2434.269424] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 2434.269427] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm)
[ 2434.269430] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm)
[ 2434.269432] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm)
[ 2434.269435] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 2815.192353] wlan0: deauthenticating from 10:bd:18:3c:2a:a1 by local choice (reason=3)
[ 2815.193679] cfg80211: Calling CRDA to update world regulatory domain
[ 2815.281425] cfg80211: World regulatory domain updated:
[ 2815.281437] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2815.281441] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2815.281444] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2815.281446] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 2815.281449] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 2815.281452] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 2815.281455] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 2861.096651] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[ 2861.223862] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2861.316979] sungem_phy: PHY ID: 1410cc2, addr: 0
[ 2861.317038] gem 0002:24:0f.0 eth0: Found Marvell 88E1111 PHY
[ 2861.317566] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2909.109902] wlan0: authenticate with 10:bd:18:3c:2a:a1
[ 2909.112753] wlan0: send auth to 10:bd:18:3c:2a:a1 (try 1/3)
[ 2909.115168] wlan0: authenticated
[ 2909.119999] wlan0: associate with 10:bd:18:3c:2a:a1 (try 1/3)
[ 2909.126786] wlan0: RX AssocResp from 10:bd:18:3c:2a:a1 (capab=0x431 status=0 aid=68)
[ 2909.127093] wlan0: associated
[ 2909.127150] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2909.127266] cfg80211: Calling CRDA for country: US
[ 2909.182091] cfg80211: Regulatory domain changed to country: US
[ 2909.182104] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2909.182108] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 2909.182112] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm)
[ 2909.182114] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm)
[ 2909.182117] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm)
[ 2909.182120] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 2958.021358] wlan0: deauthenticating from 10:bd:18:3c:2a:a1 by local choice (reason=3)
[ 2958.031401] cfg80211: Calling CRDA to update world regulatory domain
[ 2958.109990] cfg80211: World regulatory domain updated:
[ 2958.110003] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2958.110007] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2958.110009] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2958.110012] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 2958.110015] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 2958.110018] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 2958.110021] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 2986.078710] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[ 2986.155257] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2986.251041] sungem_phy: PHY ID: 1410cc2, addr: 0
[ 2986.251104] gem 0002:24:0f.0 eth0: Found Marvell 88E1111 PHY
[ 2986.251621] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2990.134293] wlan0: authenticate with 00:1e:4a:e4:57:21
[ 2990.142804] wlan0: send auth to 00:1e:4a:e4:57:21 (try 1/3)
[ 2990.346627] wlan0: send auth to 00:1e:4a:e4:57:21 (try 2/3)
[ 2990.347851] wlan0: authenticated
[ 2990.350678] wlan0: associate with 00:1e:4a:e4:57:21 (try 1/3)
[ 2990.354124] wlan0: RX AssocResp from 00:1e:4a:e4:57:21 (capab=0x431 status=0 aid=42)
[ 2990.354439] wlan0: associated
[ 2990.354491] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2990.354643] cfg80211: Calling CRDA for country: US
[ 2990.402302] cfg80211: Regulatory domain changed to country: US
[ 2990.402315] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2990.402319] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 2990.402322] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm)
[ 2990.402325] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm)
[ 2990.402328] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm)
[ 2990.402331] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 2995.802329] wlan0: authenticate with 10:bd:18:3c:2a:a1
[ 2995.814687] wlan0: send auth to 10:bd:18:3c:2a:a1 (try 1/3)
[ 2995.814839] cfg80211: Calling CRDA to update world regulatory domain
[ 2995.816240] wlan0: authenticated
[ 2995.838587] wlan0: associate with 10:bd:18:3c:2a:a1 (try 1/3)
[ 2995.841881] wlan0: RX AssocResp from 10:bd:18:3c:2a:a1 (capab=0x431 status=0 aid=68)
[ 2995.842198] wlan0: associated
[ 2995.855242] cfg80211: World regulatory domain updated:
[ 2995.855256] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2995.855259] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2995.855263] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 2995.855265] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 2995.855268] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 2995.855271] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 2995.855274] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 2995.855306] cfg80211: Calling CRDA for country: US
[ 2995.881823] cfg80211: Regulatory domain changed to country: US
[ 2995.881836] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 2995.881840] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 2995.881843] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm)
[ 2995.881846] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm)
[ 2995.881849] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm)
[ 2995.881852] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
** Model information
revision : 1.2 (pvr 8003 0102)
platform : PowerMac
model : PowerBook5,7
machine : PowerBook5,7
motherboard : PowerBook5,7 MacRISC3 Power Macintosh
** Loaded modules:
ctr
ccm
rtl8192se
rtl_pci
rtlwifi
rtl8187
eeprom_93cx6
rfcomm
bnep
binfmt_misc
uinput
hfs
btusb
bluetooth
joydev
arc4
appletouch
evdev
radeon
b43
bcma
mac80211
ams
input_polldev
snd_aoa_codec_onyx
snd_aoa
ttm
drm_kms_helper
yenta_socket
drm
pcmcia_rsrc
cfg80211
rfkill
rng_core
therm_adt746x
snd_powermac
snd_pcm
snd_page_alloc
snd_seq
snd_seq_device
snd_timer
snd
soundcore
loop
fuse
autofs4
hid_apple
ext4
crc16
mbcache
jbd2
hid_generic
usbhid
hid
dm_mod
sg
sd_mod
firewire_ohci
sr_mod
crc_t10dif
sungem
firewire_core
sungem_phy
crc_itu_t
crct10dif_common
cdrom
ehci_pci
ohci_pci
ohci_hcd
ehci_hcd
usbcore
ssb
usb_common
mmc_core
pcmcia
pcmcia_core
** PCI devices:
0000:00:0b.0 Host bridge [0600]: Apple Inc. UniNorth 2 AGP [106b:0034]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
Capabilities: <access denied>
Kernel driver in use: agpgart-uninorth
0000:00:10.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] RV350/M10 [Mobility Radeon 9600 PRO Turbo] [1002:4e50] (prog-if 00 [VGA controller])
Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RV350/M10 [Mobility Radeon 9600 PRO Turbo] [1002:4e50]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at b8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 0400 [size=256]
Region 2: Memory at b0000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at b0020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
0001:10:0b.0 Host bridge [0600]: Apple Inc. UniNorth 2 PCI [106b:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
0001:10:12.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03)
Subsystem: Apple Inc. AirPort Extreme [106b:004e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Interrupt: pin A routed to IRQ 52
Region 0: Memory at a0006000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
0001:10:13.0 CardBus bridge [0607]: Texas Instruments PCI1510 PC card Cardbus Controller [104c:ac56]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 53
Region 0: Memory at a0005000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=10, secondary=11, subordinate=14, sec-latency=176
Memory window 0: 84000000-87ffffff (prefetchable)
Memory window 1: 88000000-8bffffff
I/O window 0: 00001000-000010ff
I/O window 1: 00001100-000011ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Capabilities: <access denied>
Kernel driver in use: yenta_cardbus
0001:10:17.0 Unassigned class [ff00]: Apple Inc. KeyLargo/Intrepid Mac I/O [106b:003e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
Kernel driver in use: macio
0001:10:19.0 USB controller [0c03]: Apple Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (750ns min, 21500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at a0004000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
0001:10:1a.0 USB controller [0c03]: Apple Inc. KeyLargo/Intrepid USB [106b:003f] (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (750ns min, 21500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at a0003000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci-pci
0001:10:1b.0 USB controller [0c03]: NEC Corporation OHCI USB Controller [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB Controller [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 63
Region 0: Memory at a0002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci-pci
0001:10:1b.1 USB controller [0c03]: NEC Corporation OHCI USB Controller [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB Controller [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 63
Region 0: Memory at a0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci-pci
0001:10:1b.2 USB controller [0c03]: NEC Corporation uPD72010x USB 2.0 Controller [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation uPD72010x USB 2.0 Controller [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 63
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
0002:24:0b.0 Host bridge [0600]: Apple Inc. UniNorth 2 Internal PCI [106b:0036]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 32 bytes
0002:24:0d.0 Unassigned class [ff00]: Apple Inc. UniNorth/Intrepid ATA/100 [106b:003b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 39
Region 0: Memory at f5004000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: pata-pci-macio
0002:24:0e.0 FireWire (IEEE 1394) [0c00]: Apple Inc. UniNorth 2 FireWire [106b:0031] (rev 81) (prog-if 10 [OHCI])
Subsystem: Apple Inc. iBook G4 2004 [106b:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (3000ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
0002:24:0f.0 Ethernet controller [0200]: Apple Inc. UniNorth 2 GMAC (Sun GEM) [106b:0032] (rev 80)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 16 (16000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f5200000 (32-bit, non-prefetchable) [size=2M]
Expansion ROM at f5100000 [disabled] [size=1M]
Kernel driver in use: gem
** USB devices:
Bus 002 Device 002: ID 0b05:1786 ASUSTek Computer, Inc. USB-N10 802.11n Network Adapter [Realtek RTL8188SU]
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 003: ID 05ac:020e Apple, Inc. Internal Keyboard/Trackpad (ANSI)
Bus 003 Device 004: ID 05ac:8205 Apple, Inc. Bluetooth HCI
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: powerpc (ppc)
Kernel: Linux 3.13-1-powerpc
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.13-1-powerpc depends on:
ii debconf [debconf-2.0] 1.5.52
ii initramfs-tools [linux-initramfs-tool] 0.115
ii kmod 16-2
ii linux-base 3.5
ii module-init-tools 16-2
Versions of packages linux-image-3.13-1-powerpc recommends:
ii firmware-linux-free 3.3
Versions of packages linux-image-3.13-1-powerpc suggests:
pn debian-kernel-handbook <none>
pn linux-doc-3.13 <none>
pn mkvmlinuz <none>
Versions of packages linux-image-3.13-1-powerpc is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.41
ii firmware-linux-nonfree 0.41
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.41
pn xen-hypervisor <none>
-- debconf information excluded
Reply to: