Bug#735172: linux: Upgrade to linux-image-3.12-1-kirkwood prevents QNAP TS-119 from booting
Package: linux
Version: 3.12.6-2
Severity: important
Dear Maintainer,
I upgraded a QNAP TS-119 from linux-image-3.11-2-kirkwood to linux-image-3.12-1-kirkwood.
dpkg.log states:
2014-01-06 14:37:08 upgrade linux-image-kirkwood:armel 3.11+54 3.12+55
On the next reboot, the NAS was stuck early. I gave it a whole afternoon to boot, initially thinking an fsck was going on (which can take some time on a slow
CPU with a large drive). I used the recovery console to get more information and instructions from http://cyrius.com/debian/kirkwood/qnap/ts-119/uboot/ to get
back to normal, by reflashing linux-image-3.11-2-kirkwood over the failing 3.12.
I suspect http://comments.gmane.org/gmane.linux.debian.ports.arm/13582 to be the same issue on a close hardware.
Here is the boot log from the console:
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F6281A-BP LE
U-Boot 1.1.4 (Feb 9 2009 - 11:13:32) Marvell version: 3.4.4
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690DCC
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
[16384kB@f8000000] Flash: 16 MB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME]
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode
Device 0 @ 0 0:
Model: WDC WD10EADS-00L5B1 Firm: 01.01A01 Ser#: WD-WCAU4D159618
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
Hit any key to stop autoboot: 0
## Booting image at 00800000 ...
Image Name: kernel 3.12-1-kirkwood
Created: 2014-01-12 12:05:37 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1929800 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Thank you
--
Sylvain
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (990, 'testing'), (50, 'unstable'), (40, 'experimental')
Architecture: armel (armv5tel)
Kernel: Linux 3.11-2-kirkwood
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Reply to: