Bug#768962: linux-image-3.2.0-4-sparc64-smp: [sparc] wheezy kernel hangs when loading i2c during boot
Package: src:linux
Version: 3.2.63-2+deb7u1
Severity: normal
Dear Maintainer,
a regression in the hopefully still maintained wheezy sparc kernel: The older version
linux-image-3.2.0-3-sparc64-smp boots without problems. This is a hard hang, break
did not bring a prom prompt and a reset issued from the rsc is not working.
Only powering off from rsc works after around 10 sec delay.
Please ask if you need other information, will try a vanilla 3.17.2 kernel when the machine reboots
the next time.
Thanks and greetings
Hermann
-- console log
Sun Fire 480R, No Keyboard
Copyright 2005 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.17.1, 14336 MB memory installed, Serial #<xxx>
....
[ 0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.17.1 2005/04/11 14:27'
[ 0.000000] PROMLIB: Root node compatible:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-sparc64-smp (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.63-2+deb7u1
[ 0.000000] bootconsole [earlyprom0] enabled
[ 0.000000] ARCH: SUN4U
[ 0.000000] Ethernet address: 00:03:ba:2c:de:50
[ 0.000000] Kernel: Using 2 locked TLB entries for main kernel image.
[ 0.000000] Remapping the kernel... done.
[ 0.000000] OF stdout device is: /pci@9,700000/ebus@1/serial@1,400000:a
[ 0.000000] PROM: Built device tree with 107523 bytes of memory.
[ 0.000000] Top of RAM: 0xb17fb38000, Total RAM: 0x37fb1e000
[ 0.000000] Memory hole size: 712704MB
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x05000000 -> 0x058bfd9c
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[6] active PFN ranges
[ 0.000000] 0: 0x05000000 -> 0x05100000
[ 0.000000] 0: 0x05800000 -> 0x058bf7ff
[ 0.000000] 0: 0x058bf800 -> 0x058bfd17
[ 0.000000] 0: 0x058bfd19 -> 0x058bfd83
[ 0.000000] 0: 0x058bfd8b -> 0x058bfd99
[ 0.000000] 0: 0x058bfd9b -> 0x058bfd9c
[ 0.000000] Booting Linux...
[ 0.000000] CPU CAPS: [flush,stbar,swap,muldiv,v9,ultra3,mul32,div32]
[ 0.000000] CPU CAPS: [v8plus,vis,vis2]
[ 0.000000] PERCPU: Embedded 6 pages/cpu @fffff8a007400000 s20416 r8192 d20544 u1048576
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1762707
[ 0.000000] Kernel command line: root=/dev/md0 ro
[ 0.000000] PID hash table entries: 4096 (order: 2, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 2097152 (order: 11, 16777216 bytes)
[ 0.000000] Inode-cache hash table entries: 1048576 (order: 10, 8388608 bytes)
[ 0.000000] Memory: 14518232k available (3600k kernel code, 1488k data, 232k init) [fffff80000000000,000000b17fb38000]
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:255
[ 0.000000] clocksource: mult[64000000] shift[24]
[ 0.000000] clockevent: mult[28f5c29] shift[32]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.17.1 2005/04/11 14:27'
[ 0.000000] PROMLIB: Root node compatible:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-sparc64-smp (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.63-2+deb7u1
[ 0.000000] bootconsole [earlyprom0] enabled
[ 0.000000] ARCH: SUN4U
[ 0.000000] Ethernet address: 00:03:ba:2c:de:50
[ 0.000000] Kernel: Using 2 locked TLB entries for main kernel image.
[ 0.000000] Remapping the kernel... done.
[ 0.000000] OF stdout device is: /pci@9,700000/ebus@1/serial@1,400000:a
[ 0.000000] PROM: Built device tree with 107523 bytes of memory.
[ 0.000000] Top of RAM: 0xb17fb38000, Total RAM: 0x37fb1e000
[ 0.000000] Memory hole size: 712704MB
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x05000000 -> 0x058bfd9c
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[6] active PFN ranges
[ 0.000000] 0: 0x05000000 -> 0x05100000
[ 0.000000] 0: 0x05800000 -> 0x058bf7ff
[ 0.000000] 0: 0x058bf800 -> 0x058bfd17
[ 0.000000] 0: 0x058bfd19 -> 0x058bfd83
[ 0.000000] 0: 0x058bfd8b -> 0x058bfd99
[ 0.000000] 0: 0x058bfd9b -> 0x058bfd9c
[ 0.000000] Booting Linux...
[ 0.000000] CPU CAPS: [flush,stbar,swap,muldiv,v9,ultra3,mul32,div32]
[ 0.000000] CPU CAPS: [v8plus,vis,vis2]
[ 0.000000] PERCPU: Embedded 6 pages/cpu @fffff8a007400000 s20416 r8192 d20544 u1048576
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1762707
[ 0.000000] Kernel command line: root=/dev/md0 ro
[ 0.000000] PID hash table entries: 4096 (order: 2, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 2097152 (order: 11, 16777216 bytes)
[ 0.000000] Inode-cache hash table entries: 1048576 (order: 10, 8388608 bytes)
[ 0.000000] Memory: 14518232k available (3600k kernel code, 1488k data, 232k init) [fffff80000000000,000000b17fb38000]
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:255
[ 0.000000] clocksource: mult[64000000] shift[24]
[ 0.000000] clockevent: mult[28f5c29] shift[32]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 70.519589] Calibrating delay using timer specific routine.. 20.00 BogoMIPS (lpj=40014)
[ 70.519616] pid_max: default: 32768 minimum: 301
[ 70.519801] Security Framework initialized
[ 70.519836] AppArmor: AppArmor disabled by boot time parameter
[ 70.519926] Mount-cache hash table entries: 512
[ 70.520637] Initializing cgroup subsys cpuacct
[ 70.520683] Initializing cgroup subsys memory
[ 70.520730] Initializing cgroup subsys devices
[ 70.520744] Initializing cgroup subsys freezer
[ 70.520758] Initializing cgroup subsys net_cls
[ 70.520772] Initializing cgroup subsys blkio
[ 70.520801] Initializing cgroup subsys perf_event
[ 70.521082] Performance events: Supported PMU type is 'ultra3+'
[ 70.523090] CPU 0: synchronized TICK with master CPU (last diff 0 cycles, maxerr 11 cycles)
[ 70.524399] CPU 1: synchronized TICK with master CPU (last diff 0 cycles, maxerr 11 cycles)
[ 70.525710] CPU 2: synchronized TICK with master CPU (last diff 0 cycles, maxerr 11 cycles)
[ 70.525766] Brought up 4 CPUs
[ 70.525800] Testing NMI watchdog ... OK.
[ 70.607087] devtmpfs: initialized
[ 70.608015] print_constraints: dummy:
[ 70.608291] NET: Registered protocol family 16
[ 70.614728] /pci@8,700000: SCHIZO PCI Bus Module ver[4:0]
[ 70.614758] /pci@8,700000: PCI IO[7ffef000000] MEM[7fe00000000]
[ 70.619738] PCI: Scanning PBM /pci@8,700000
[ 70.620167] /pci@8,600000: SCHIZO PCI Bus Module ver[4:0]
[ 70.620194] /pci@8,600000: PCI IO[7ffed000000] MEM[7fd00000000]
[ 70.625179] PCI: Scanning PBM /pci@8,600000
[ 70.625652] /pci@9,700000: SCHIZO PCI Bus Module ver[4:0]
[ 70.625679] /pci@9,700000: PCI IO[7ffeb000000] MEM[7fc00000000]
[ 70.630659] PCI: Scanning PBM /pci@9,700000
[ 70.632763] /pci@9,600000: SCHIZO PCI Bus Module ver[4:0]
[ 70.632791] /pci@9,600000: PCI IO[7ffe9000000] MEM[7fb00000000]
[ 70.637752] PCI: Scanning PBM /pci@9,600000
[ 70.641400] bio: create slab <bio-0> at 0
[ 70.641979] vgaarb: loaded
[ 70.643034] /pci@9,700000/ebus@1/rtc@1,300070: RTC regs at 0x7fc7e300070
[ 70.643845] Switching to clocksource stick
[ 70.657448] NET: Registered protocol family 2
[ 70.666077] IP route cache hash table entries: 524288 (order: 9, 4194304 bytes)
[ 70.670825] TCP established hash table entries: 524288 (order: 10, 8388608 bytes)
[ 70.704530] TCP bind hash table entries: 65536 (order: 7, 1048576 bytes)
[ 70.708775] TCP: Hash tables configured (established 524288 bind 65536)
[ 70.708798] TCP reno registered
[ 70.708830] UDP hash table entries: 8192 (order: 5, 262144 bytes)
[ 70.709939] UDP-Lite hash table entries: 8192 (order: 5, 262144 bytes)
[ 70.711491] NET: Registered protocol family 1
[ 70.764216] Unpacking initramfs...
[ 71.467351] Freeing initrd memory: 10652k freed
[ 71.468579] power: Control reg at 7fc7e30002e
[ 71.469104] chmc: UltraSPARC-III memory controller at /memory-controller@0,400000 [ACTIVE]
[ 71.469158] chmc: UltraSPARC-III memory controller at /memory-controller@1,400000 [ACTIVE]
[ 71.469209] chmc: UltraSPARC-III memory controller at /memory-controller@2,400000 [ACTIVE]
[ 71.469258] chmc: UltraSPARC-III memory controller at /memory-controller@3,400000 [ACTIVE]
[ 71.469819] audit: initializing netlink socket (disabled)
[ 71.469875] type=2000 audit(1.032:1): initialized
[ 71.506497] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 71.507496] VFS: Disk quotas dquot_6.5.2
[ 71.507722] Dquot-cache hash table entries: 1024 (order 0, 8192 bytes)
[ 71.508087] msgmni has been set to 28376
[ 71.508822] alg: No test for stdrng (krng)
[ 71.508962] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 71.508997] io scheduler noop registered
[ 71.509014] io scheduler deadline registered
[ 71.509091] io scheduler cfq registered (default)
[ 71.510629] f00b6110: ttyS0 at MMIO 0x7fc7e3062f8 (irq = 14) is a 16550A
[ 71.510827] f00b7a38: ttyS1 at MMIO 0x7fc7e3083f8 (irq = 15) is a 16550A
[ 71.511249] f00b9360: ttyS2 at MMIO 0x7fc7e400000 (irq = 16) is a SAB82532 V3.2
[ 71.511279] Console: ttyS2 (SAB82532)
[ 78.511920] console [ttyS0] enabled
[ 78.553613] f00b9360: ttyS3 at MMIO 0x7fc7e400040 (irq = 16) is a SAB82532 V3.2
[ 78.642917] mousedev: PS/2 mouse device common for all mice
[ 78.709435] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 78.784744] rtc0: no alarms, 114 bytes nvram
[ 78.836821] TCP cubic registered
[ 78.874685] NET: Registered protocol family 10
[ 78.929641] Mobile IPv6
[ 78.957841] NET: Registered protocol family 17
[ 79.010978] Registering the dns_resolver key type
[ 79.067306] registered taskstats version 1
[ 79.116502] rtc_cmos rtc_cmos: setting system clock to 2014-11-10 08:13:03 UTC (1415607183)
[ 79.216223] Initializing network drop monitor service?Loading, please wait...
[ 79.325777] udevd[59]: starting version 175
[ 79.443341] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 79.483440] cassini: cassini.c:v1.6 (21 May 2008)
[ 79.507569] cassini 0002:00:02.0: eth0: Sun Cassini+ (64bit/33MHz PCI/Cu) Ethernet[18] 00:03:ba:2c:de:51
[ 79.514176] cassini 0003:00:01.0: eth1: Sun Cassini+ (64bit/66MHz PCI/Cu) Ethernet[23] 00:03:ba:2c:de:50
[ 79.644949] usbcore: registered new interface driver usbfs
[ 79.645028] usbcore: registered new interface driver hub
[ 79.652912] usbcore: registered new device driver usb
[ 79.654339] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 79.655182] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 79.655257] ohci_hcd 0002:00:01.3: OHCI Host Controller
[ 79.655355] ohci_hcd 0002:00:01.3: new USB bus registered, assigned bus number 1
[ 79.655451] ohci_hcd 0002:00:01.3: irq 17, io mem 0x7fc01000000
[ 79.711994] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 79.712006] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 79.712016] usb usb1: Product: OHCI Host Controller
[ 79.712024] usb usb1: Manufacturer: Linux 3.2.0-4-sparc64-smp ohci_hcd
[ 79.712031] usb usb1: SerialNumber: 0002:00:01.3
[ 79.712758] hub 1-0:1.0: USB hub found
[ 79.712783] hub 1-0:1.0: 4 ports detected
[ 80.825912] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 80.895083] SCSI subsystem initialized
[ 80.951498] pata_cmd64x 0000:00:06.0: Secondary port is disabled
[ 81.022527] qla2xxx [0000:00:00.0]-0005: : QLogic Fibre Channel HBA Driver: 8.03.07.12-k.
[ 81.023293] scsi0 : pata_cmd64x
[ 81.158020] qla2xxx [0003:00:02.0]-001d: : Found an ISP2200 irq 27 iobase 0x000007fb00400000.
[ 81.158181] scsi1 : pata_cmd64x
[ 81.158315] ata1: PATA max UDMA/33 cmd 0x7ffef000300 ctl 0x7ffef000318 bmdma 0x7ffef000320 irq 5
[ 81.158324] ata2: DUMMY
[ 81.315208] e1000 0001:00:01.0: eth2: (PCI:66MHz:64-bit) 00:1b:21:43:87:d6
[ 81.315230] e1000 0001:00:01.0: eth2: Intel(R) PRO/1000 Network Connection
[ 81.344351] ata1.00: ATAPI: TOSHIBA DVD-ROM SD-C2612, 1011, max UDMA/33
[ 81.376293] ata1.00: configured for UDMA/33
[ 81.726325] qla2xxx [0003:00:02.0]-0040:2: Configuring PCI space...
[ 81.800870] qla2xxx [0003:00:02.0]-0050:2: No matching ROM signature.
[ 81.877741] qla2xxx [0003:00:02.0]-0061:2: Configure NVRAM parameters...
[ 81.962301] scsi 0:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-C2612 1011 PQ: 0 ANSI: 5
[ 82.053469] qla2xxx [0003:00:02.0]-0064:2: Inconisistent NVRAM detected: checksum=0x0 id=? version=0xff.
[ 82.053483] qla2xxx [0003:00:02.0]-0065:2: Falling back to functioning (yet invalid -- WWPN) defaults.
[ 82.053499] qla2xxx [0003:00:02.0]-0069:2: NVRAM configuration failed.
[ 82.053510] qla2xxx [0003:00:02.0]-0078:2: Verifying loaded RISC code...
[ 82.453747] qla2xxx 0003:00:02.0: firmware: agent loaded ql2200_fw.bin into memory
[ 82.562326] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 82.635339] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 82.704841] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 93.203993] qla2xxx [0003:00:02.0]-00c5:2: Allocated (252 KB) for firmware dump.
[ 93.431911] qla2xxx [0003:00:02.0]-500c:2: LIP reset occurred (f8ef).
[ 93.508235] scsi2 : qla2xxx
[ 93.521434] qla2xxx [0003:00:02.0]-5009:2: LIP occurred (f8ef).
[ 93.526872] qla2xxx [0003:00:02.0]-500a:2: LOOP UP detected (1 Gbps).
[ 93.690788] qla2xxx [0003:00:02.0]-00fa:2: QLogic Fibre Channed HBA Driver: 8.03.07.12-k.
[ 93.787807] qla2xxx [0003:00:02.0]-00fb:2: QLogic QLA22xx - .
[ 93.795040] scsi 2:0:0:0: Direct-Access SEAGATE ST336605FSUN36G 0638 PQ: 0 ANSI: 3
[ 93.795504] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 93.802547] scsi 2:0:1:0: Direct-Access SEAGATE ST336605FSUN36G 0638 PQ: 0 ANSI: 3
[ 93.802907] scsi 2:0:1:0: Attached scsi generic sg2 type 0
[ 94.181564] qla2xxx [0003:00:02.0]-00fc:2: ISP2200: PCI (66 MHz) @ 0003:00:02.0 hdma- host#=2 fw=2.02.08 TP.
[ 94.313546] sd 2:0:0:0: [sda] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB)
[ 94.403313] sd 2:0:1:0: [sdb] 71132959 512-byte logical blocks: (36.4 GB/33.9 GiB)
[ 94.405802] sd 2:0:0:0: [sda] Write Protect is off
[ 94.410196] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 94.432887] sda: sda1 sda2 sda3 sda4
[ 94.700191] sd 2:0:1:0: [sdb] Write Protect is off
[ 94.708824] sd 2:0:0:0: [sda] Attached SCSI disk
[ 94.816626] sd 2:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA
[ 94.939565] sdb: sdb1 sdb2 sdb3 sdb4
[ 94.994526] sd 2:0:1:0: [sdb] Attached SCSI disk
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... Begin: Assembling all MD arrays ... [ 97.627824] md: md1 stopped.
[ 97.678196] md: bind<sdb1>
[ 97.712885] md: bind<sda1>
[ 97.748719] md: raid1 personality registered for level 1
[ 97.811868] bio: create slab <bio-1> at 1
[ 97.859500] md/raid1:md1: active with 2 out of 2 mirrors
[ 97.922877] md1: detected capacity change from 0 to 98631680
mdadm: /d[ 98.000223] md1: p1 p2 p3 p4
[ 98.035328] md1: p1 size 192780 extends beyond EOD, truncated
[ 98.104221] md1: p2 start 192780 is beyond EOD, truncated
[ 98.168600] md1: p3 size 71119755 extends beyond EOD, truncated
[ 98.239595] md1: p4 start 62685630 is beyond EOD, truncated
ev/md1 has been started with 2 drives.
[ 98.535744] md: md0 stopped.
[ 98.698662] md: bind<sdb2>
[ 98.737601] md: bind<sda2>
[ 98.772905] md/raid1:md0: active with 2 out of 2 mirrors
[ 98.835610] md0: detected capacity change from 0 to 31996248064
mdadm: /dev/md/0[ 98.923866] md0: unknown partition table
has been started with 2 drives.
Success: assembled all arrays.
done.
done.
Begin: Running /scripts/local-premount ... done.
[ 99.611086] EXT4-fs (md0): mounted filesystem with ordered data mode. Opts: (null)
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatc[ 101.613966] udevd[423]: starting version 175
her: udevd[ ok .
[....] Synthesizing the initial hotplug events...[ ok done.
[....] Waiting for /dev to be fully populated...[ 102.117421] i2c-0: Regs at 000007fc7e00002e, 8 devices, own a0, clock 10.
[ 102.198867] i2c-0: Regs at 000007fc7e000030, 8 devices, own a0, clock 10.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
cpu : TI UltraSparc III+ (Cheetah+)
fpu : UltraSparc III+ integrated FPU
pmu : ultra3+
prom : OBP 4.17.1 2005/04/11 14:27
type : sun4u
** PCI devices:
0000:00:06.0 IDE interface [0101]: Silicon Image, Inc. PCI0646 [1095:0646] (rev 07) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Silicon Image, Inc. PCI0646 [1095:0646]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 0300 [size=8]
Region 1: I/O ports at 0318 [size=8]
Region 2: I/O ports at 0310 [size=8]
Region 3: I/O ports at 0308 [size=8]
Region 4: I/O ports at 0320 [size=16]
Region 5: [virtual] Memory at fffff80200000000 (32-bit, non-prefetchable) [size=1]
[virtual] Expansion ROM at fffff80200000000 [disabled] [size=1]
Capabilities: <access denied>
Kernel driver in use: pata_cmd64x
0001:00:01.0 Ethernet controller [0200]: Intel Corporation 82545GM Gigabit Ethernet Controller [8086:1026] (rev 04)
Subsystem: Intel Corporation PRO/1000 MT Server Adapter [8086:1001]
Physical Slot: PCI 0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 7
Region 0: Memory at 00100000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at 00140000 (64-bit, non-prefetchable) [size=256K]
Region 4: I/O ports at 0300 [disabled] [size=64]
Region 5: [virtual] Memory at fffff80300000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at 00180000 [disabled] [size=256K]
Capabilities: <access denied>
Kernel driver in use: e1000
0002:00:01.0 Bridge [0680]: Oracle/SUN RIO EBUS [108e:1100] (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 6250ns max), Cache Line Size: 64 bytes
BIST result: 00
Region 0: Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 1: Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 2: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 3: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at fffff80400000000 [disabled] [size=1]
0002:00:01.3 USB controller [0c03]: Oracle/SUN RIO USB [108e:1103] (rev 01) (prog-if 10 [OHCI])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 1250ns max), Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 17
BIST result: 00
Region 0: Memory at 01000000 (32-bit, non-prefetchable) [size=16M]
Region 1: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 2: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 3: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at 00c00000 [disabled] [size=4M]
Kernel driver in use: ohci_hcd
0002:00:02.0 Ethernet controller [0200]: Oracle/SUN Cassini 10/100/1000 [108e:abba] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min, 16000ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at 00200000 (32-bit, non-prefetchable) [size=2M]
Region 1: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 2: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 3: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffff80400000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at 02000000 [disabled] [size=1M]
Kernel driver in use: cassini
0003:00:01.0 Ethernet controller [0200]: Oracle/SUN Cassini 10/100/1000 [108e:abba] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min, 16000ns max), Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 23
Region 0: Memory at 00200000 (32-bit, non-prefetchable) [size=2M]
Region 1: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Region 2: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Region 3: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at 00100000 [disabled] [size=1M]
Kernel driver in use: cassini
0003:00:02.0 SCSI storage controller [0100]: QLogic Corp. QLA2200 64-bit Fibre Channel Adapter [1077:2200] (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: I/O ports at 0300 [size=256]
Region 1: Memory at 00400000 (32-bit, non-prefetchable) [size=8K]
Region 2: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Region 3: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Region 4: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Region 5: [virtual] Memory at fffff80500000000 (32-bit, non-prefetchable) [size=1]
Expansion ROM at 00420000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: qla2xxx
** USB devices:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 7.7
APT prefers stable
APT policy: (500, 'stable')
Architecture: sparc (sparc64)
Kernel: Linux 3.2.0-3-sparc64-smp (SMP w/1 CPU core)
Locale: LANG=C.UTF-8, LC_CTYPE=C.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-sparc64-smp depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
Versions of packages linux-image-3.2.0-4-sparc64-smp recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.2.0-4-sparc64-smp suggests:
pn debian-kernel-handbook <none>
pn fdutils <none>
pn linux-doc-3.2 <none>
ii silo 1.4.14+git20120819-1
Versions of packages linux-image-3.2.0-4-sparc64-smp is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-sparc64-smp/postinst/depmod-error-initrd-3.2.0-4-sparc64-smp: false
linux-image-3.2.0-4-sparc64-smp/postinst/missing-firmware-3.2.0-4-sparc64-smp:
linux-image-3.2.0-4-sparc64-smp/prerm/removing-running-kernel-3.2.0-4-sparc64-smp: true
linux-image-3.2.0-4-sparc64-smp/postinst/ignoring-ramdisk:
Reply to: