Bug#765182: alsa: Unable to set buffer time near: Invalid argument
Package: src:linux
Version: 3.16.5-1
Severity: normal
Hi,
I'm using my computer to read DVD images with mplayer on the second screen
attached to HDMI (Intel card). This HDMI output is linked to an AV receiver.
I do not use this installation very often. But, a few days ago, I did not
succeed into sending sound and video throught HDMI. My goal here was to send 6
channels through HDMI (so the sound is decoded by mplayer and sent as PCM
flows). It does not work. mplayer displays:
[AO_ALSA] Unable to set buffer time near: Invalid argument
Failed to initialize audio driver 'alsa:device=hw=0.7'
Could not open/initialize audio device -> no sound.
Audio: no sound
And then, of course, no sound.
If I send the sound through spdif (another plug also connected to the AV
receiver), it works (but, of cause, with only two channels)
If I use HDMI for the sound and I ask mplayer to use only 2 channels,
it works.
If I use HDMI for the sound and I ask mplayer to use 1, 3, 4, 5 or 6 channels,
it fails with the previous message
After trying lots of configuration, after googling a lot, I found this webpage:
http://mailman.alsa-project.org/pipermail/alsa-devel/2014-February/072265.html
And, indeed, I was suffering the same bug.
With 64 as value in /proc/asound/card0/pcm7p/sub0/prealloc, I have the previous
error message from mplayer.
But mplayer works fine if I write 63, 65 and 128 in
/proc/asound/card0/pcm7p/sub0/prealloc (I did not test other values)
So, it seems to me that there is a bug with the 64 value when using not 2
channels.
Even if this bug is not fixed, I hope this bug report will help people with
similar problems as there is an easy workaround.
Regards,
Vincent
-- Package-specific info:
** Version:
Linux version 3.16-3-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.3 (Debian 4.8.3-12) ) #1 SMP Debian 3.16.5-1 (2014-10-10)
** Command line:
BOOT_IMAGE=/vmlinuz-3.16-3-amd64 root=/dev/mapper/aya+raid1-root ro init=/bin/systemd quiet systemd.log_level=debug
** Not tainted
** Kernel log:
[ 1523.017597] kvm [4538]: vcpu0 unhandled rdmsr: 0x345
[ 1523.018224] kvm_set_msr_common: 22 callbacks suppressed
[ 1523.018225] kvm [4538]: vcpu0 unhandled wrmsr: 0x680 data 0
[ 1523.018832] kvm [4538]: vcpu0 unhandled wrmsr: 0x6c0 data 0
[ 1523.019386] kvm [4538]: vcpu0 unhandled wrmsr: 0x681 data 0
[ 1523.019944] kvm [4538]: vcpu0 unhandled wrmsr: 0x6c1 data 0
[ 1523.020499] kvm [4538]: vcpu0 unhandled wrmsr: 0x682 data 0
[ 1523.021053] kvm [4538]: vcpu0 unhandled wrmsr: 0x6c2 data 0
[ 1523.021618] kvm [4538]: vcpu0 unhandled wrmsr: 0x683 data 0
[ 1523.022154] kvm [4538]: vcpu0 unhandled wrmsr: 0x6c3 data 0
[ 1523.046223] kvm [4538]: vcpu0 unhandled wrmsr: 0x684 data 0
[ 1523.046736] kvm [4538]: vcpu0 unhandled wrmsr: 0x6c4 data 0
[ 1523.310505] br-dmz: port 6(vn_urtho_00) entered learning state
[ 1523.514824] kvm [4561]: vcpu0 unhandled rdmsr: 0x345
[ 1525.389503] kvm [4578]: vcpu0 unhandled rdmsr: 0x345
[ 1525.713221] br-lan: topology change detected, sending tcn bpdu
[ 1525.713240] br-lan: port 4(vn_ogmios_00) entered forwarding state
[ 1525.713288] br-kooot1: port 1(eth1) received tcn bpdu
[ 1525.713290] br-kooot1: topology change detected, propagating
[ 1525.720487] kvm [4595]: vcpu0 unhandled rdmsr: 0x345
[ 1526.257840] br-dmz: topology change detected, sending tcn bpdu
[ 1526.257860] br-dmz: port 2(vn_ran_00) entered forwarding state
[ 1526.642277] br-dmz: topology change detected, sending tcn bpdu
[ 1526.642300] br-dmz: port 3(vn_yoko_00) entered forwarding state
[ 1527.090778] br-dmz: topology change detected, sending tcn bpdu
[ 1527.090788] br-dmz: port 4(vn_talia_00) entered forwarding state
[ 1527.475211] br-lan: topology change detected, sending tcn bpdu
[ 1527.475219] br-lan: port 5(vn_belgarath_00) entered forwarding state
[ 1527.475262] br-kooot1: port 1(eth1) received tcn bpdu
[ 1527.475263] br-kooot1: topology change detected, propagating
[ 1527.875668] br-dmz: topology change detected, sending tcn bpdu
[ 1527.875688] br-dmz: port 5(vn_rosee_00) entered forwarding state
[ 1528.324173] br-dmz: topology change detected, sending tcn bpdu
[ 1528.324183] br-dmz: port 6(vn_urtho_00) entered forwarding state
[ 1576.927444] br-lan: port 3(vn_kooot_01) received tcn bpdu
[ 1576.927448] br-lan: topology change detected, sending tcn bpdu
[ 1576.927542] br-kooot1: port 1(eth1) received tcn bpdu
[ 1576.927546] br-kooot1: topology change detected, propagating
[ 1774.650959] systemd[1]: Sent message type=signal sender=n/a destination=n/a object=/org/freedesktop/systemd1/unit/loc_2densure_2dldap_2eservice interface=org.freedesktop.DBus.Properties member=PropertiesChanged cookie=602 reply_cookie=0 error=n/a
[ 1774.662967] systemd[1]: Got notification message for unit systemd-machined.service
[ 1774.674971] systemd[1]: systemd-machined.service: Got notification message from PID 4470 (WATCHDOG=1...)
[ 1774.687022] systemd[1]: systemd-machined.service: got WATCHDOG=1
[ 1774.699007] systemd[1]: Got notification message for unit systemd-machined.service
[ 1774.710985] systemd[1]: systemd-machined.service: Got notification message from PID 4470 (WATCHDOG=1...)
[ 1774.723002] systemd[1]: systemd-machined.service: got WATCHDOG=1
[ 1774.735050] systemd[1]: Got notification message for unit systemd-logind.service
[ 1774.747034] systemd[1]: systemd-logind.service: Got notification message from PID 3439 (WATCHDOG=1...)
[ 1774.759080] systemd[1]: systemd-logind.service: got WATCHDOG=1
[ 1859.903402] systemd[1]: user@2001.service: Got notification message from PID 8697 (READY=1...)
[ 1859.915407] systemd[1]: user@2001.service: got READY=1
[ 1859.927416] systemd[1]: user@2001.service changed start -> running
[ 1859.939474] systemd[1]: Job user@2001.service/start finished, result=done
[ 1859.963455] systemd[1]: Sent message type=signal sender=n/a destination=n/a object=/org/freedesktop/systemd1 interface=org.freedesktop.systemd1.Manager member=JobRemoved cookie=774 reply_cookie=0 error=n/a
[ 1859.975470] systemd[1]: Sent message type=method_call sender=n/a destination=org.freedesktop.DBus object=/org/freedesktop/DBus interface=org.freedesktop.DBus member=RemoveMatch cookie=775 reply_cookie=0 error=n/a
[ 1859.987467] systemd[1]: user@2001.service: got STATUS=Startup finished in 56ms.
[ 1859.999493] systemd[1]: Got notification message for unit user@2001.service
[ 1860.011491] systemd[1]: user@2001.service: Got notification message from PID 8697 (READY=1...)
[ 1860.023502] systemd[1]: user@2001.service: got STATUS=Startup finished in 56ms.
[ 1860.035523] systemd[1]: Sent message type=signal sender=n/a destination=n/a object=/org/freedesktop/systemd1/unit/user_402001_2eservice interface=org.freedesktop.DBus.Properties member=PropertiesChanged cookie=776 reply_cookie=0 error=n/a
[ 1860.047552] systemd[1]: Sent message type=signal sender=n/a destination=n/a object=/org/freedesktop/systemd1/unit/user_402001_2eservice interface=org.freedesktop.DBus.Properties member=PropertiesChanged cookie=777 reply_cookie=0 error=n/a
[ 2338.875785] snd_hda_intel 0000:00:1b.0: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[ 2395.925900] systemd[1]: systemd-journald.service: got WATCHDOG=1
[ 2395.937949] systemd[1]: Got notification message for unit systemd-logind.service
[ 2395.949922] systemd[1]: systemd-logind.service: Got notification message from PID 3439 (WATCHDOG=1...)
[ 2395.965933] systemd[1]: systemd-logind.service: got WATCHDOG=1
[ 2395.977953] systemd[1]: Got notification message for unit systemd-logind.service
[ 2395.989963] systemd[1]: systemd-logind.service: Got notification message from PID 3439 (WATCHDOG=1...)
[ 5276.623007] systemd[1]: /etc
[ 8236.627633] systemd[1]: systemd-logind.service: got WATCHDOG=1
[ 8236.639696] systemd[1]: Received SIGCHLD from PID 9254 (sshd).
[ 8236.651669] systemd[1]: Child 9254 (sshd) died (code=exited, status=255/n/a)
[ 8236.663681] systemd[1]: Got message type=signal sender=org.freedesktop.DBus destination=n/a object=/org/freedesktop/DBus interface=org.freedesktop.DBus member=NameOwnerChanged cookie=39 reply_cookie=0 error=n/a
[ 8236.675690] systemd[1]: Accepted new private connection.
[ 8921.350394] systemd[1]: Collecting session-68.scope
[ 8921.362407] systemd[1]: Sent message type=signal sender=n/a destination=n/a object=/org/freedesktop/systemd1 interface=org.freedesktop.systemd1.Manager member=UnitRemoved cookie=938 reply_cookie=0 error=n/a
[ 8921.374423] systemd[1]: Accepted new private connection.
[ 8921.386427] systemd[1]: Got message type=method_call sender=:1.1 destination=org.freedesktop.systemd1 object=/org/freedesktop/systemd1/unit/session_2d68_2escope interface=org.freedesktop.DBus.Properties member=Get cookie=249 reply_cookie=0 error=n/a
[ 8921.402447] systemd[1]: Failed to load configuration for session-68.scope: No such file or directory
[ 8921.414463] systemd[1]: Sent message type=method_return sender=n/a destination=:1.1 object=n/a interface=n/a member=n/a cookie=939 reply_cookie=249 error=n/a
[ 8921.426478] systemd[1]: Collecting session-68.scope
[ 8921.438490] systemd[1]: Sent message type=signal sender=n/a destination=n/a object=/org/freedesktop/systemd1 interface=org.freedesktop.systemd1.Manager member=UnitNew cookie=940 reply_cookie=0 error=n/a
[ 8921.450502] systemd[1]: Sent message type=signal sender=n/a destination=n/a object=/org/freedesktop/systemd1 interface=org.freedesktop.systemd1.Manager member=UnitRemoved cookie=941 reply_cookie=0 error=n/a
[ 9386.941352] systemd[1]: Got message type=signal sender=org.freedesktop.DBus destination=n/a object=/org/freedesktop/DBus interface=org.freedesktop.DBus member=NameOwnerChanged cookie=60 reply_cookie=0 error=n/a
[ 9386.953354] systemd[1]: Accepted new private connection.
[ 9386.965380] systemd[1]: Got message type=method_call sender=:1.1 destination=org.freedesktop.systemd1 object=/org/freedesktop/systemd1/unit/session_2d13_2escope interface=org.freedesktop.systemd1.Scope member=Abandon cookie=262 reply_cookie=0 error=n/a
[ 9386.977393] systemd[1]: Sent message type=method_call sender=n/a destination=org.freedesktop.DBus object=/org/freedesktop/DBus interface=org.freedesktop.DBus member=GetConnectionUnixUser cookie=955 reply_cookie=0 error=n/a
[ 9386.989407] systemd[1]: session-13.scope: cgroup is empty
[13054.319620] perf interrupt took too long (2510 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[32306.993350] systemd[1]: /usr/local/lib/systemd/system
[32307.005400] systemd[1]: /lib/systemd/system
[32307.017369] systemd[1]: /usr/lib/systemd/system
[32307.029376] systemd[1]: Looking for SysV init scripts in:
[32307.041406] systemd[1]: /etc/init.d
[38653.901040] systemd[1]: Sent message type=method_return sender=n/a destination=:1.1 object=n/a interface=n/a member=n/a cookie=1017 reply_cookie=297 error=n/a
[38653.913064] systemd[1]: Collecting session-281.scope
[38653.925106] systemd[1]: Sent message type=signal sender=n/a destination=n/a object=/org/freedesktop/systemd1 interface=org.freedesktop.systemd1.Manager member=UnitRemoved cookie=1018 reply_cookie=0 error=n/a
[38653.937090] systemd[1]: Got notification message for unit systemd-machined.service
[38653.949102] systemd[1]: systemd-machined.service: Got notification message from PID 4470 (WATCHDOG=1...)
[38653.961148] systemd[1]: systemd-machined.service: got WATCHDOG=1
[67497.778557] hrtimer: interrupt took 6419 ns
** Model information
sys_vendor: Gigabyte Technology Co., Ltd.
product_name: H67A-UD3H-B3
product_version:
chassis_vendor: Gigabyte Technology Co., Ltd.
chassis_version:
bios_vendor: Award Software International, Inc.
bios_version: F8
board_vendor: Gigabyte Technology Co., Ltd.
board_name: H67A-UD3H-B3
board_version: x.x
** Loaded modules:
vhost_net
vhost
macvtap
macvlan
tun
cpufreq_powersave
cpufreq_userspace
cpufreq_conservative
cpufreq_stats
binfmt_misc
dm_snapshot
dm_bufio
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
fscache
sunrpc
ctr
ccm
bridge
8021q
garp
stp
mrp
llc
iTCO_wdt
iTCO_vendor_support
pl2303
usbserial
x86_pkg_temp_thermal
intel_powerclamp
intel_rapl
kvm_intel
kvm
crc32_pclmul
ghash_clmulni_intel
arc4
aesni_intel
ath9k
ath9k_common
ath9k_hw
aes_x86_64
ath
mac80211
cfg80211
rfkill
lrw
gf128mul
glue_helper
ablk_helper
cryptd
pcspkr
snd_hda_codec_hdmi
snd_hda_codec_realtek
snd_hda_codec_generic
snd_hda_intel
snd_hda_controller
snd_hda_codec
snd_hwdep
snd_pcm_oss
snd_mixer_oss
serio_raw
snd_pcm
mei_me
i2c_i801
snd_timer
shpchp
lpc_ich
evdev
mei
mfd_core
snd
soundcore
processor
coretemp
it87
hwmon_vid
firewire_sbp2
loop
fuse
autofs4
ext4
crc16
mbcache
jbd2
dm_mod
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
async_tx
xor
raid6_pq
sr_mod
cdrom
raid1
md_mod
sg
hid_generic
usbhid
hid
sd_mod
crc_t10dif
crct10dif_generic
crct10dif_pclmul
crct10dif_common
crc32c_intel
firewire_ohci
3c59x
firewire_core
crc_itu_t
uhci_hcd
sata_via
ahci
libahci
ehci_pci
i915
ehci_hcd
i2c_algo_bit
video
r8169
libata
mii
drm_kms_helper
xhci_hcd
drm
scsi_mod
usbcore
i2c_core
usb_common
thermal_sys
button
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0100] (rev 09)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: snb_uncore
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: fbc00000-fbcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0102] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Gigabyte Technology Co., Ltd Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at fb400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at ff00 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: Gigabyte Technology Co., Ltd Device [1458:1c3a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 50
Region 0: Memory at fbfff000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: Gigabyte Technology Co., Ltd Device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: Gigabyte Technology Co., Ltd Device [1458:a102]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 51
Region 0: Memory at fbff4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: dfa00000-dfbfffff
Prefetchable memory behind bridge: 00000000dfc00000-00000000dfdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 [8086:1c14] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbb00000-fbbfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Memory behind bridge: fba00000-fbafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 [8086:1c1a] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Prefetchable memory behind bridge: 00000000fbe00000-00000000fbefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.6 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev b5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=06, subordinate=07, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fbd00000-fbdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: Gigabyte Technology Co., Ltd Device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge [0601]: Intel Corporation H67 Express Chipset Family LPC Controller [8086:1c4a] (rev 05)
Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family SATA AHCI Controller [8086:1c02] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: Gigabyte Technology Co., Ltd Device [1458:b005]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 47
Region 0: I/O ports at fe00 [size=8]
Region 1: I/O ports at fd00 [size=4]
Region 2: I/O ports at fc00 [size=8]
Region 3: I/O ports at fb00 [size=4]
Region 4: I/O ports at fa00 [size=32]
Region 5: Memory at fbffc000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: Gigabyte Technology Co., Ltd Device [1458:5001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbffb000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
01:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) (prog-if 30 [XHCI])
Subsystem: Gigabyte Technology Co., Ltd Device [1458:5007]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbcfe000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
03:00.0 SATA controller [0106]: ASMedia Technology Inc. ASM1062 Serial ATA Controller [1b21:0612] (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: ASMedia Technology Inc. Device [1b21:1060]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 48
Region 0: I/O ports at ef00 [size=8]
Region 1: I/O ports at ee00 [size=4]
Region 2: I/O ports at ed00 [size=8]
Region 3: I/O ports at ec00 [size=4]
Region 4: I/O ports at eb00 [size=32]
Region 5: Memory at fbbff000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at fbb00000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
04:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
Subsystem: Qualcomm Atheros Device [168c:30a1]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbaf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 46
Region 0: I/O ports at de00 [size=256]
Region 2: Memory at fbeff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fbef8000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
06:00.0 PCI bridge [0604]: Integrated Technology Express, Inc. Device [1283:8892] (rev 10) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=06, secondary=07, subordinate=07, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fbd00000-fbdfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat+ DiscTmrSERREn-
Capabilities: <access denied>
07:00.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 74)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC Management NIC [10b7:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 2500ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at cf00 [size=128]
Region 1: Memory at fbdff000 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at fbd00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: 3c59x
07:01.0 RAID bus controller [0104]: VIA Technologies, Inc. VT6421 IDE/SATA Controller [1106:3249] (rev 50)
Subsystem: VIA Technologies, Inc. VT6421 IDE/SATA Controller [1106:3249]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at ce00 [size=16]
Region 1: I/O ports at cd00 [size=16]
Region 2: I/O ports at cc00 [size=16]
Region 3: I/O ports at cb00 [size=16]
Region 4: I/O ports at ca00 [size=32]
Region 5: I/O ports at c600 [size=256]
[virtual] Expansion ROM at fbd20000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: sata_via
07:02.0 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at c900 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
07:02.1 USB controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at c800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
07:02.2 USB controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 65) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 Controller [1106:3104]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbdfe000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
07:03.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Gigabyte Technology Co., Ltd Motherboard [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbdfd000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fbdf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
** USB devices:
Bus 005 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 006: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard
Bus 003 Device 005: ID 046d:c016 Logitech, Inc. Optical Wheel Mouse
Bus 003 Device 004: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
Bus 003 Device 010: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Bus 003 Device 009: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Bus 003 Device 008: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Bus 003 Device 007: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Bus 003 Device 003: ID 0409:005a NEC Corp. HighSpeed Hub
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable'), (500, 'oldstable'), (1, 'experimental')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.16-3-amd64 (SMP w/4 CPU cores)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.16-3-amd64 depends on:
ii debconf [debconf-2.0] 1.5.53
ii initramfs-tools [linux-initramfs-tool] 0.116
ii kmod 18-3
ii linux-base 3.5
ii module-init-tools 18-3
Versions of packages linux-image-3.16-3-amd64 recommends:
ii firmware-linux-free 3.3
Versions of packages linux-image-3.16-3-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.00-22
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16-3-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.43
ii firmware-linux-nonfree 0.43
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.43
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16-3-amd64/postinst/depmod-error-initrd-3.16-3-amd64: false
linux-image-3.16-3-amd64/postinst/mips-initrd-3.16-3-amd64:
linux-image-3.16-3-amd64/prerm/removing-running-kernel-3.16-3-amd64: true
Reply to: