Bug#764877: linux-image-3.2.0-4-686-pae: Failure to suspend
Package: src:linux
Version: 3.2.60-1+deb7u3
Severity: normal
Dear Maintainer,
Since upgrade to Debian 7, I sometimes find that the system is suspended (?)
and when I try to wake it up it does not come back up. That is, the power
light is flashing, the screen is blank, and it is silent. If I press any key,
the disks spin up, and the screen shows a flashing line text cursor in the
upper-left corner. It doesn't respond to any input other than that, so I
have to turn the power off and on again.
The system never goes to suspend when I'm logged in, only when other family-
members are logged in.
The only log entry I can find at about the likely time of suspend for
today is in "kern.log"...
Oct 11 10:54:53 huitzil kernel: [143518.747118] PM: Syncing filesystems ... done.
Thus it's possible I'm seeing the same problem as #733088, but I'm not sure.
"dmesg" output below is from the reboot _after_ the failed resume.
-- Package-specific info:
** Version:
Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.60-1+deb7u3
** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-4-686-pae root=/dev/mapper/huitzil-lvRoot ro quiet
** Not tainted
** Kernel log:
[ 8.009120] EXT3-fs (dm-0): 7 orphan inodes deleted
[ 8.009124] EXT3-fs (dm-0): recovery complete
[ 8.066328] EXT3-fs (dm-0): mounted filesystem with ordered data mode
[ 9.993593] udevd[357]: starting version 175
[ 10.634680] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/PNP0C0C:00/input/input1
[ 10.634692] ACPI: Power Button [PWRB]
[ 10.634846] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 10.634856] ACPI: Power Button [PWRF]
[ 10.648991] ACPI: Requesting acpi_cpufreq
[ 11.030410] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 11.189178] ACPI: resource 0000:00:1f.3 [io 0x3080-0x309f] conflicts with ACPI region SMB0 [io 0x3080-0x3097]
[ 11.189185] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 11.228926] udevd[421]: renamed network interface eth0 to rename2
[ 11.265090] udevd[413]: renamed network interface eth1 to eth0
[ 11.296684] udevd[421]: renamed network interface rename2 to eth1
[ 11.386690] parport_pc 00:0d: reported by Plug and Play ACPI
[ 11.386777] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 11.481223] tpm_tis 00:0e: [irq 10]
[ 11.481244] tpm_tis 00:0e: [mem 0xfed40000-0xfed40fff]
[ 11.481557] tpm_tis 00:0e: activated
[ 11.481899] tpm_tis 00:0e: 1.2 TPM (device-id 0xFE, rev-id 3)
[ 11.507727] intel_rng: FWH not detected
[ 11.544582] [drm] Initialized drm 1.1.0 20060810
[ 11.978474] iTCO_vendor_support: vendor-support=0
[ 12.028347] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 12.028558] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x1060)
[ 12.029466] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 12.087630] leds_ss4200: no LED devices found
[ 12.126652] i915 0000:00:02.0: setting latency timer to 64
[ 12.163448] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 12.163455] [drm] Driver supports precise vblank timestamp query.
[ 12.163544] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 12.189144] [drm] initialized overlay support
[ 12.233818] fbcon: inteldrmfb (fb0) is primary device
[ 12.279878] Console: switching to colour frame buffer device 160x64
[ 12.286854] fb0: inteldrmfb frame buffer device
[ 12.286857] drm: registered panic notifier
[ 12.286868] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 12.312401] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[ 12.312459] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 12.347973] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[ 12.527630] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input5
[ 15.652541] EXT3-fs (dm-0): using internal journal
[ 15.927788] loop: module loaded
[ 16.576212] device-mapper: snapshots: Snapshot is marked invalid.
[ 16.669543] Buffer I/O error on device dm-5, logical block 13369328
[ 16.669689] Buffer I/O error on device dm-5, logical block 13369328
[ 16.669844] Buffer I/O error on device dm-5, logical block 13369342
[ 16.669978] Buffer I/O error on device dm-5, logical block 13369342
[ 16.670127] Buffer I/O error on device dm-5, logical block 0
[ 16.670253] Buffer I/O error on device dm-5, logical block 0
[ 16.670384] Buffer I/O error on device dm-5, logical block 1
[ 16.670526] Buffer I/O error on device dm-5, logical block 13369343
[ 16.670914] Buffer I/O error on device dm-5, logical block 13369343
[ 16.671057] Buffer I/O error on device dm-5, logical block 13369343
[ 16.967363] Adding 2658300k swap on /dev/mapper/huitzil-swap_1. Priority:-1 extents:1 across:2658300k
[ 24.287544] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[ 24.302476] EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
[ 24.369213] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 25.732689] e1000e 0000:02:00.0: irq 42 for MSI/MSI-X
[ 25.836132] e1000e 0000:02:00.0: irq 42 for MSI/MSI-X
[ 25.836941] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.003554] RPC: Registered named UNIX socket transport module.
[ 26.003562] RPC: Registered udp transport module.
[ 26.003567] RPC: Registered tcp transport module.
[ 26.003572] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 26.110590] FS-Cache: Loaded
[ 26.142011] FS-Cache: Netfs 'nfs' registered for caching
[ 26.172495] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 27.424706] fuse init (API version 7.17)
[ 28.002484] Loading iSCSI transport class v2.0-870.
[ 28.106869] iscsi: registered transport (tcp)
[ 28.336079] iscsi: registered transport (iser)
[ 28.714782] NET: Registered protocol family 15
[ 28.761287] alg: No test for cipher_null (cipher_null-generic)
[ 28.761362] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 28.761440] alg: No test for digest_null (digest_null-generic)
[ 28.761508] alg: No test for compress_null (compress_null-generic)
[ 29.810593] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[ 29.810766] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO
[ 29.811003] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 43.816982] tun: Universal TUN/TAP device driver, 1.6
[ 43.816990] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 48.182827] Bluetooth: Core ver 2.16
[ 48.182866] NET: Registered protocol family 31
[ 48.182872] Bluetooth: HCI device and connection manager initialized
[ 48.182878] Bluetooth: HCI socket layer initialized
[ 48.182883] Bluetooth: L2CAP socket layer initialized
[ 48.182900] Bluetooth: SCO socket layer initialized
[ 48.272968] Bluetooth: RFCOMM TTY layer initialized
[ 48.272982] Bluetooth: RFCOMM socket layer initialized
[ 48.272989] Bluetooth: RFCOMM ver 1.11
[ 48.546518] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 48.546526] Bluetooth: BNEP filters: protocol multicast
[ 50.017292] lp0: using parport0 (interrupt-driven).
[ 50.221498] ppdev: user-space parallel port driver
[ 53.808021] teredo: no IPv6 routers present
[ 70.969768] IPv6 over IPv4 tunneling driver
[ 78.662021] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 78.780366] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
** Model information
not available
** Loaded modules:
xt_tcpudp
iptable_nat
nf_nat
nf_conntrack_ipv4
nf_defrag_ipv4
nf_conntrack
ipt_REJECT
iptable_filter
ip_tables
x_tables
sit
tunnel4
ppdev
lp
bnep
rfcomm
bluetooth
rfkill
cpufreq_powersave
cpufreq_stats
cpufreq_conservative
cpufreq_userspace
tun
binfmt_misc
quota_v2
quota_tree
deflate
zlib_deflate
ctr
twofish_generic
twofish_i586
twofish_common
camellia
serpent
blowfish_generic
blowfish_common
cast5
des_generic
cbc
cryptd
aes_i586
aes_generic
xcbc
rmd160
sha512_generic
sha256_generic
sha1_generic
hmac
crypto_null
af_key
ib_iser
rdma_cm
ib_addr
iw_cm
ib_cm
ib_sa
ib_mad
ib_core
iscsi_tcp
libiscsi_tcp
libiscsi
scsi_transport_iscsi
fuse
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
nls_utf8
nls_cp437
vfat
fat
ext4
crc16
jbd2
ext2
dm_snapshot
loop
ecryptfs
snd_hda_codec_analog
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm_oss
snd_mixer_oss
snd_pcm
i915
iTCO_wdt
snd_page_alloc
iTCO_vendor_support
video
drm_kms_helper
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_seq
snd_seq_device
snd_timer
drm
tpm_tis
snd
parport_pc
tpm
acpi_cpufreq
i2c_algo_bit
parport
rng_core
tpm_bios
mperf
i2c_i801
evdev
i2c_scmi
i2c_core
pcspkr
soundcore
psmouse
serio_raw
processor
container
button
ext3
mbcache
jbd
dm_mod
sr_mod
sg
cdrom
sd_mod
crc_t10dif
ahci
ata_generic
libahci
uhci_hcd
ata_piix
floppy
pata_jmicron
libata
thermal
ehci_hcd
8139too
thermal_sys
e1000e
scsi_mod
usbcore
8139cp
mii
usb_common
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet static
address 192.168.123.11
netmask 255.255.255.0
network 192.168.123.0
broadcast 192.168.123.255
gateway 192.168.123.1
# dns-* options are implemented by the resolvconf package, if installed
dns-nameservers 192.168.123.1
dns-search lmert.com
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:40:f4:af:ed:22 brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:10:c6:b6:37:d4 brd ff:ff:ff:ff:ff:ff
inet 192.168.123.11/24 brd 192.168.123.255 scope global eth0
inet6 2601:4:5400:ebc:210:c6ff:feb6:37d4/64 scope global dynamic
valid_lft 2242sec preferred_lft 1642sec
inet6 fe80::210:c6ff:feb6:37d4/64 scope link
valid_lft forever preferred_lft forever
4: teredo: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1280 qdisc pfifo_fast state UNKNOWN qlen 500
link/none
inet6 2001:0:53aa:64c:28ef:2604:baa6:98b0/32 scope global
valid_lft forever preferred_lft forever
inet6 fe80::ffff:ffff:ffff/64 scope link
valid_lft forever preferred_lft forever
5: sit0: <NOARP> mtu 1480 qdisc noop state DOWN
link/sit 0.0.0.0 brd 0.0.0.0
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 1384917 1935 0 0 0 0 0 0 1384917 1935 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
sit0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
teredo: 0 0 0 0 0 0 0 0 144 3 0 0 0 0 0 0
eth0: 97076251 154422 0 0 0 0 0 22 53629942 73998 0 0 0 0 0 0
*** Protocol statistics:
Ip:
155189 total packets received
0 forwarded
0 incoming packets discarded
106328 incoming packets delivered
55478 requests sent out
54570 reassemblies required
5709 packets reassembled ok
9913 fragments received ok
29614 fragments created
Icmp:
51539 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 15
redirects: 51522
echo replies: 2
17 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 15
echo request: 2
IcmpMsg:
InType0: 2
InType3: 15
InType5: 51522
OutType3: 15
OutType8: 2
Tcp:
442 active connections openings
43 passive connection openings
106 failed connection attempts
33 connection resets received
30 connections established
13063 segments received
11498 segments send out
438 segments retransmited
9 bad segments received.
111 resets sent
Udp:
41948 packets received
0 packets to unknown port received.
0 packet receive errors
44135 packets sent
UdpLite:
TcpExt:
1 resets received for embryonic SYN_RECV sockets
67 TCP sockets finished time wait in fast timer
372 delayed acks sent
Quick ack mode was activated 20 times
15 packets directly queued to recvmsg prequeue.
174 bytes directly received in process context from prequeue
7647 packet headers predicted
3 packets header predicted and directly queued to user
1157 acknowledgments not containing data payload received
2108 predicted acknowledgments
4 times recovered from packet loss by selective acknowledgements
7 congestion windows recovered without slow start after partial ack
33 TCP data loss events
TCPLostRetransmit: 5
32 fast retransmits
6 forward retransmits
94 other TCP timeouts
1 SACK retransmits failed
20 DSACKs sent for old packets
6 DSACKs received
10 connections reset due to unexpected data
21 connections reset due to early user close
63 connections aborted due to timeout
TCPDSACKIgnoredNoUndo: 2
TCPSpuriousRTOs: 1
TCPSackShifted: 32
TCPSackMerged: 64
TCPSackShiftFallback: 23
TCPChallengeACK: 9
TCPSYNChallenge: 9
IpExt:
InMcastPkts: 78
OutMcastPkts: 80
InBcastPkts: 394
OutBcastPkts: 143
InOctets: 95644945
OutOctets: 53231324
InMcastOctets: 12307
OutMcastOctets: 12624
InBcastOctets: 45748
OutBcastOctets: 17445
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub [8086:2770] (rev 02)
Subsystem: IBM Device [1014:02f6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 82945G/GZ Integrated Graphics Controller [8086:2772] (rev 02) (prog-if 00 [VGA controller])
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0300000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 30c0 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at d0380000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation 82945G/GZ Integrated Graphics Controller [8086:2776] (rev 02)
Subsystem: IBM Device [1014:02f6]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [disabled] [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: IBM Device [1014:02f6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at d05c0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0000000-d00fffff
Prefetchable memory behind bridge: 0000000080500000-00000000806fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: d0100000-d01fffff
Prefetchable memory behind bridge: 0000000080200000-00000000804fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 3000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 3040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 3060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: IBM Device [1014:02f6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d05c4000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=32
I/O behind bridge: 00006000-00006fff
Memory behind bridge: d0200000-d02fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 IDE interface [0101]: Intel Corporation NM10/ICH7 Family SATA Controller [IDE mode] [8086:27c0] (rev 01) (prog-if 80 [Master])
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 30b0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 01)
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 3080 [size=32]
02:00.0 Ethernet controller [0200]: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) [8086:108c] (rev 03)
Subsystem: IBM Device [1014:02f6]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 42
Region 0: Memory at d0080000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 4000 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
04:00.0 SATA controller [0106]: JMicron Technology Corp. JMB363 SATA/IDE Controller [197b:2363] (rev 10) (prog-if 01 [AHCI 1.0])
Subsystem: JMicron Technology Corp. JMB363 SATA/IDE Controller [197b:2363]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 43
Region 5: Memory at d0100000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 80200000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
04:00.1 IDE interface [0101]: JMicron Technology Corp. JMB368 IDE controller [197b:0368] (rev 10) (prog-if 85 [Master SecO PriO])
Subsystem: JMicron Technology Corp. Device [197b:1368]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 5020 [size=8]
Region 1: I/O ports at 5014 [size=4]
Region 2: I/O ports at 5018 [size=8]
Region 3: I/O ports at 5010 [size=4]
Region 4: I/O ports at 5000 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_jmicron
0a:0a.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 6000 [size=256]
Region 1: Memory at d0200000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: 8139too
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 04b8:011d Seiko Epson Corp. Perfection 1260 Photo
-- System Information:
Debian Release: 7.6
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-4-686-pae (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-686-pae depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-686-pae recommends:
ii firmware-linux-free 3.2
ii libc6-i686 2.13-38+deb7u4
Versions of packages linux-image-3.2.0-4-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u2
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-686-pae/postinst/missing-firmware-3.2.0-4-686-pae:
linux-image-3.2.0-4-686-pae/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-686-pae/postinst/depmod-error-initrd-3.2.0-4-686-pae: false
linux-image-3.2.0-4-686-pae/prerm/removing-running-kernel-3.2.0-4-686-pae: true
Reply to: