Bug#748517: linux-image-3.14-1-686-pae: Must insert "acpi=off" on boot, otherwise Toshiba Laptop freezes (see #746312)
Package: src:linux
Version: 3.14.4-1
Severity: normal
Dear Maintainer,
* What led up to the situation? kernel upgrades after 3.12
* What exactly did you do (or not do) that was effective (or
ineffective)? boot kernel 3.14.4-1
* What was the outcome of this action? laptop gets unresponsive
* What outcome did you expect instead? up to kernel 3.12, the problem didn't exist
-- Package-specific info:
** Version:
Linux version 3.14-1-686-pae (debian-kernel@lists.debian.org) (gcc version 4.8.2 (Debian 4.8.2-21) ) #1 SMP Debian 3.14.4-1 (2014-05-13)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.14-1-686-pae root=UUID=02f6a568-3f47-435b-81a6-34b8f4e6785e acpi=off ro quiet
** Not tainted
** Kernel log:
[ 8.964796] donauboe 0000:00:09.0: found PCI INT A -> IRQ 11
[ 8.966098] IrDA: Registered device irda0
[ 8.966112] toshoboe: Using multiple tasks
[ 9.345280] pcmcia_socket pcmcia_socket0: pccard: CardBus card inserted into slot 0
[ 9.345341] pci 0000:02:00.0: [14e4:4318] type 00 class 0x028000
[ 9.345385] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x00001fff]
[ 9.345812] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c001fff]
[ 9.345846] pci 0000:02:00.0: cache line size of 32 is not supported
[ 9.408046] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
[ 9.408640] excluding 0x170-0x177 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x37f
[ 9.409155] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
[ 9.409421] excluding 0x3f0-0x3ff 0x480-0x48f 0x4d0-0x4d7
[ 9.409726] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
[ 9.410079] clean.
[ 9.410166] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
[ 9.410555] clean.
[ 9.410653] pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
[ 9.410680] excluding 0xc0000-0xcbfff 0xe8000-0xebfff 0xf0000-0xfffff
[ 9.410818] pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
[ 9.410897] clean.
[ 9.410983] pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
[ 9.411060] clean.
[ 9.411147] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
[ 9.411548] clean.
[ 9.412031] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af:
[ 9.412612] excluding 0x170-0x177 0x1f0-0x1f7 0x2f8-0x2ff 0x370-0x37f
[ 9.413129] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff:
[ 9.413607] excluding 0x3f0-0x3ff 0x480-0x48f 0x4d0-0x4d7
[ 9.413919] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff:
[ 9.414272] clean.
[ 9.414359] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7:
[ 9.414748] clean.
[ 9.414851] pcmcia_socket pcmcia_socket1: cs: memory probe 0x0c0000-0x0fffff:
[ 9.414876] excluding 0xc0000-0xcbfff 0xe8000-0xebfff 0xf0000-0xfffff
[ 9.415015] pcmcia_socket pcmcia_socket1: cs: memory probe 0xa0000000-0xa0ffffff:
[ 9.415094] clean.
[ 9.415180] pcmcia_socket pcmcia_socket1: cs: memory probe 0x60000000-0x60ffffff:
[ 9.415258] clean.
[ 9.415344] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff:
[ 9.415746] clean.
[ 9.637808] b43-pci-bridge 0000:02:00.0: enabling device (0000 -> 0002)
[ 9.646499] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input2
[ 9.657433] ssb: Found chip with id 0x4318, rev 0x02 and package 0x02
[ 9.657464] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
[ 9.657484] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
[ 9.657503] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
[ 9.657522] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
[ 9.701861] ssb: Sonics Silicon Backplane found on PCI device 0000:02:00.0
[ 9.933871] snd_ymfpci 0000:00:0c.0: found PCI INT A -> IRQ 11
[ 9.933924] snd_ymfpci 0000:00:0c.0: sharing IRQ 11 with 0000:00:0b.1
[ 9.979788] cfg80211: Calling CRDA to update world regulatory domain
[ 10.059821] snd_ymfpci 0000:00:0c.0: firmware: direct-loading firmware yamaha/ds1_dsp.fw
[ 10.090392] snd_ymfpci 0000:00:0c.0: firmware: direct-loading firmware yamaha/ds1e_ctrl.fw
[ 10.275969] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
[ 10.317462] b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
[ 10.341779] Broadcom 43xx driver loaded [ Features: PMNLS ]
[ 10.485605] b43 ssb0:0: firmware: direct-loading firmware b43/ucode5.fw
[ 10.496496] b43 ssb0:0: firmware: direct-loading firmware b43/pcm5.fw
[ 10.496987] b43 ssb0:0: firmware: direct-loading firmware b43/b0g0initvals5.fw
[ 10.497498] b43 ssb0:0: firmware: direct-loading firmware b43/b0g0bsinitvals5.fw
[ 10.574612] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.408637] Adding 523260k swap on /dev/sda5. Priority:-1 extents:1 across:523260k
[ 13.534937] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 14.183066] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 15.720044] lp: driver loaded but no devices found
[ 15.800845] ppdev: user-space parallel port driver
[ 15.873152] parport_pc 00:10: reported by Plug and Play BIOS
[ 15.873242] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 15.975699] lp0: using parport0 (interrupt-driven).
[ 16.135077] loop: module loaded
[ 16.384931] fuse init (API version 7.22)
[ 36.663427] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[ 36.708159] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 37.873678] mtrr: base(0xff400000) is not aligned on a size(0x280000) boundary
[ 42.788890] systemd-logind[1919]: New seat seat0.
[ 42.795537] systemd-logind[1919]: New session c1 of user lightdm.
[ 42.796367] systemd-logind[1919]: Linked /tmp/.X11-unix/X0 to /run/user/105/X11-display.
[ 63.540116] wlan0: authenticate with 00:1e:e5:46:0b:0c
[ 63.558285] wlan0: send auth to 00:1e:e5:46:0b:0c (try 1/3)
[ 63.560259] wlan0: authenticated
[ 63.569330] b43 ssb0:0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 63.569359] b43 ssb0:0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 63.569374] b43 ssb0:0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 63.570734] wlan0: associate with 00:1e:e5:46:0b:0c (try 1/3)
[ 63.572877] wlan0: RX AssocResp from 00:1e:e5:46:0b:0c (capab=0x431 status=0 aid=3)
[ 63.573296] wlan0: associated
[ 63.573468] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 501.547698] ieee80211 phy0: wlan0: No probe response from AP 00:1e:e5:46:0b:0c after 500ms, disconnecting.
[ 501.582817] cfg80211: Calling CRDA to update world regulatory domain
[ 502.857719] wlan0: authenticate with 00:1e:e5:46:0b:0c
[ 502.868254] wlan0: send auth to 00:1e:e5:46:0b:0c (try 1/3)
[ 502.872480] wlan0: authenticated
[ 502.878509] b43 ssb0:0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 502.878538] b43 ssb0:0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 502.878552] b43 ssb0:0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 502.880078] wlan0: associate with 00:1e:e5:46:0b:0c (try 1/3)
[ 502.882386] wlan0: RX AssocResp from 00:1e:e5:46:0b:0c (capab=0x431 status=0 aid=3)
[ 502.882812] wlan0: associated
[ 2463.283242] systemd-logind[1919]: New session 1 of user daniel.
[ 2463.283852] systemd-logind[1919]: Linked /tmp/.X11-unix/X0 to /run/user/1000/X11-display.
** Model information
not available
** Loaded modules:
autofs4
fuse
loop
parport_pc
ppdev
lp
parport
arc4
b43
bcma
mac80211
cfg80211
snd_ymfpci
snd_mpu401_uart
snd_seq_midi
rfkill
rng_core
snd_seq_midi_event
ssb
snd_rawmidi
snd_opl3_lib
snd_hwdep
snd_ac97_codec
snd_pcm
mmc_core
snd_seq
snd_seq_device
snd_timer
snd
soundcore
ac97_bus
gameport
donauboe
i2c_piix4
irda
pcmcia
i2c_core
pcspkr
crc_ccitt
psmouse
evdev
serio_raw
yenta_socket
pcmcia_rsrc
pcmcia_core
shpchp
ext4
crc16
mbcache
jbd2
sg
sd_mod
sr_mod
crc_t10dif
cdrom
crct10dif_common
ata_generic
ata_piix
libata
uhci_hcd
ehci_hcd
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] (rev 03)
Subsystem: Toshiba America Info Systems Toshiba Tecra 8100 Laptop System Chipset [1179:0001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: fec00000-ff7fffff
Prefetchable memory behind bridge: 14100000-141fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:05.0 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:05.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
Region 4: I/O ports at fff0 [size=16]
Kernel driver in use: ata_piix
00:05.2 USB controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB [8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at ff80 [size=32]
Kernel driver in use: uhci_hcd
00:05.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 03)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin ? routed to IRQ 9
Kernel driver in use: piix4_smbus
00:07.0 Communication controller [0780]: LSI Corporation 56k WinModem [11c1:0441] (rev 01)
Subsystem: Toshiba America Info Systems Internal V.90 Modem [1179:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 3
Region 0: Memory at ffefff00 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 02f8 [size=8]
Region 2: I/O ports at 1c00 [size=256]
Capabilities: <access denied>
00:09.0 IRDA controller [0d00]: Toshiba America Info Systems FIR Port Type-DO [1179:0d01]
Subsystem: Toshiba America Info Systems FIR Port Type-DO [1179:0001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ff60 [size=32]
Capabilities: <access denied>
Kernel driver in use: donauboe
00:0b.0 CardBus bridge [0607]: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support [1179:0617] (rev 20)
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 14000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=0
Memory window 0: 18000000-1bffffff (prefetchable)
Memory window 1: 1c000000-1fffffff
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite+
16-bit legacy interface ports at 0001
Capabilities: <access denied>
Kernel driver in use: yenta_cardbus
00:0b.1 CardBus bridge [0607]: Toshiba America Info Systems ToPIC100 PCI to Cardbus Bridge with ZV Support [1179:0617] (rev 20)
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin B routed to IRQ 11
Region 0: Memory at 20000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=0
Memory window 0: 24000000-27ffffff (prefetchable)
Memory window 1: 28000000-2bffffff
I/O window 0: 00001800-000018ff
I/O window 1: 00002000-000020ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Capabilities: <access denied>
Kernel driver in use: yenta_cardbus
00:0c.0 Multimedia audio controller [0401]: Yamaha Corporation YMF-744B [DS-1S Audio Controller] [1073:0010] (rev 02)
Subsystem: Toshiba America Info Systems Device [1179:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 64 (1250ns min, 6250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at febf8000 (32-bit, non-prefetchable) [size=32K]
Region 1: I/O ports at ff00 [size=64]
Region 2: I/O ports at fefc [size=4]
Capabilities: <access denied>
Kernel driver in use: snd_ymfpci
01:00.0 VGA compatible controller [0300]: Trident Microsystems Cyber 9525 [1023:9525] (rev 49) (prog-if 00 [VGA controller])
Subsystem: Toshiba America Info Systems Device [1179:0002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ff400000 (32-bit, non-prefetchable) [size=4M]
Region 1: Memory at ff3e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: Memory at fec00000 (32-bit, non-prefetchable) [size=4M]
[virtual] Expansion ROM at 14100000 [disabled] [size=64K]
Capabilities: <access denied>
02:00.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
Subsystem: Linksys WPC54G v3 802.11g Wireless-G Notebook Adapter [1737:0048]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 1c000000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: b43-pci-bridge
** USB devices:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (990, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.14-1-686-pae (SMP w/1 CPU core)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.14-1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.53
ii initramfs-tools [linux-initramfs-tool] 0.115
ii kmod 16-2
ii linux-base 3.5
ii module-init-tools 16-2
Versions of packages linux-image-3.14-1-686-pae recommends:
ii firmware-linux-free 3.3
ii libc6-i686 2.18-5
Versions of packages linux-image-3.14-1-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.00-22
pn linux-doc-3.14 <none>
Versions of packages linux-image-3.14-1-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.41
ii firmware-linux-nonfree 0.41
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.14-1-686-pae/prerm/removing-running-kernel-3.14-1-686-pae: true
linux-image-3.14-1-686-pae/postinst/depmod-error-initrd-3.14-1-686-pae: false
Reply to: