Bug#731473: Wheezy: eth0 not working
I have the same problem. ifonfig shows eth0 up and running but address resolution fails.
The problem exists with linux-image-3.2.0-4-amd64_3.2.57-3, downgrading to linux-image-2.6.32-5-amd64_2.6.32-48squeeze4 solves the issue.
ping 192.168.115.1
PING 192.168.115.1 (192.168.115.1) 56(84) bytes of data.
From 192.168.115.61 icmp_seq=1 Destination Host Unreachable
arp -an
? (192.168.115.1) at <incomplete> on eth0
dmesg | grep r8169
[ 1.001211] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.001261] r8169 0000:01:00.0: setting latency timer to 64
[ 1.001313] r8169 0000:01:00.0: irq 40 for MSI/MSI-X
[ 1.001706] r8169 0000:01:00.0: eth0: RTL8168d/8111d at 0xffffc90000652000, 6c:62:6d:79:c8:eb, XID 081000c0 IRQ 40
[ 1.001710] r8169 0000:01:00.0: eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 102.791430] r8169 0000:01:00.0: firmware: agent loaded rtl_nic/rtl8168d-1.fw into memory
[ 102.845915] r8169 0000:01:00.0: eth0: link down
[ 104.497739] r8169 0000:01:00.0: eth0: link up
Unfortunately, I cannot use reportbug on the failing system because any internet connection fails due to this error. Here is the information I gathered with reportbug -p -O:
Package: src:linux
Version: 3.2.57-3
Severity: important
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.57-3
** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-4-amd64 root=/dev/mapper/md2_crypt ro rootflags=data=journal panic=0 enable_mtrr_cleanup mtrr_spare_reg_nr=1 quiet
** Not tainted
** Kernel log:
[ 26.719196] IR Sony protocol handler initialized
[ 26.753586] IR MCE Keyboard/mouse protocol handler initialized
[ 26.755727] lirc_dev: IR Remote Control driver registered, major 250
[ 26.756032] IR LIRC bridge handler initialized
[ 26.776524] hda_codec: ALC889: BIOS auto-probing.
[ 26.787313] HDMI status: Codec=3 Pin=6 Presence_Detect=0 ELD_Valid=0
[ 26.787499] input: HDA Intel HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 26.787730] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 26.812117] tuner 11-004b: Tuner -1 found with type(s) Radio TV.
[ 26.850652] usb_audio: Warning! Unlikely big volume range (=17152), cval->res is probably wrong.
[ 26.850659] usb_audio: [2] FU [PCM Playback Volume] ch = 2, val = 0/17152/1
[ 26.850901] usbcore: registered new interface driver snd-usb-audio
[ 26.891907] tda829x 11-004b: setting tuner address to 60
[ 26.995645] tda829x 11-004b: type set to tda8290+75a
[ 27.026203] input: ImExPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input7
[ 30.722550] saa7133[0]: registered device video0 [v4l2]
[ 30.722691] saa7133[0]: registered device vbi0
[ 30.798507] dvb_init() allocating 1 frontend
[ 30.869976] DVB: registering new adapter (saa7133[0])
[ 30.869982] DVB: registering adapter 0 frontend 0 (Philips TDA10046H DVB-T)...
[ 30.997675] tda1004x: setting up plls for 48MHz sampling clock
[ 33.012544] tda1004x: found firmware revision 29 -- ok
[ 33.209813] kvm: VM_EXIT_LOAD_IA32_PERF_GLOBAL_CTRL does not work properly. Using workaround
[ 33.689985] saa7134 ALSA driver for DMA sound loaded
[ 33.690027] saa7133[0]/alsa: saa7133[0] at 0xfbfff800 irq 16 registered as card -1
[ 33.928305] md: md1 stopped.
[ 33.929243] md: bind<sdb5>
[ 33.929372] md: bind<sda5>
[ 33.951448] md/raid10:md1: active with 2 out of 2 devices
[ 33.951478] md1: detected capacity change from 0 to 8588361728
[ 33.967166] md1: unknown partition table
[ 34.648836] md: md3 stopped.
[ 34.649895] md: bind<sdb7>
[ 34.650120] md: bind<sda7>
[ 34.671840] md/raid10:md3: active with 2 out of 2 devices
[ 34.671875] md3: detected capacity change from 0 to 34358165504
[ 34.717911] md3: unknown partition table
[ 35.081202] md: md4 stopped.
[ 35.082140] md: bind<sdb8>
[ 35.082301] md: bind<sda8>
[ 35.104135] md/raid10:md4: active with 2 out of 2 devices
[ 35.104175] md4: detected capacity change from 0 to 34358165504
[ 35.144293] md4: unknown partition table
[ 35.547150] md: md5 stopped.
[ 35.548673] md: bind<sdb9>
[ 35.548904] md: bind<sda9>
[ 35.569653] md/raid10:md5: active with 2 out of 2 devices
[ 35.569686] md5: detected capacity change from 0 to 137437380608
[ 35.620805] md5: unknown partition table
[ 36.011895] md: md6 stopped.
[ 36.131054] md: bind<sdb10>
[ 36.132902] md: bind<sda10>
[ 36.320303] md: raid1 personality registered for level 1
[ 36.320630] md/raid1:md6: active with 2 out of 2 mirrors
[ 36.320662] md6: detected capacity change from 0 to 69883641856
[ 36.346245] md6: unknown partition table
[ 39.582182] EXT3-fs (dm-0): using internal journal
[ 43.970411] i2c /dev entries driver
[ 43.995665] loop: module loaded
[ 44.039129] f71882fg: Found f71889fg chip at 0xa00, revision 21
[ 44.039330] f71882fg f71882fg.2560: Fan: 1 is in duty-cycle mode
[ 44.039379] f71882fg f71882fg.2560: Fan: 2 is in duty-cycle mode
[ 44.039442] f71882fg f71882fg.2560: Fan: 3 is in duty-cycle mode
[ 44.410936] Adding 8387068k swap on /dev/mapper/md1_crypt. Priority:-1 extents:1 across:8387068k
[ 46.208190] kjournald starting. Commit interval 5 seconds
[ 46.233438] EXT3-fs (md0): using internal journal
[ 46.233446] EXT3-fs (md0): mounted filesystem with ordered data mode
[ 46.277941] kjournald starting. Commit interval 5 seconds
[ 46.297811] EXT3-fs (dm-2): using internal journal
[ 46.297818] EXT3-fs (dm-2): mounted filesystem with journal data mode
[ 46.348848] kjournald starting. Commit interval 5 seconds
[ 46.372905] EXT3-fs (md6): using internal journal
[ 46.372912] EXT3-fs (md6): mounted filesystem with journal data mode
[ 47.983974] RPC: Registered named UNIX socket transport module.
[ 47.983980] RPC: Registered udp transport module.
[ 47.983984] RPC: Registered tcp transport module.
[ 47.983988] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 48.083213] FS-Cache: Loaded
[ 48.145261] FS-Cache: Netfs 'nfs' registered for caching
[ 48.179272] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 48.570802] fuse init (API version 7.17)
[ 51.295188] lp: driver loaded but no devices found
[ 51.298690] ppdev: user-space parallel port driver
[ 52.121923] Bluetooth: Core ver 2.16
[ 52.121941] NET: Registered protocol family 31
[ 52.121942] Bluetooth: HCI device and connection manager initialized
[ 52.121945] Bluetooth: HCI socket layer initialized
[ 52.121946] Bluetooth: L2CAP socket layer initialized
[ 52.121950] Bluetooth: SCO socket layer initialized
[ 52.133870] Bluetooth: RFCOMM TTY layer initialized
[ 52.133875] Bluetooth: RFCOMM socket layer initialized
[ 52.133877] Bluetooth: RFCOMM ver 1.11
[ 52.234762] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 52.234764] Bluetooth: BNEP filters: protocol multicast
[ 70.734657] mc[6448]: segfault at 0 ip 00007fcb2a42d99f sp 00007fff735df760 error 4 in mc[7fcb2a3d3000+de000]
[ 102.791430] r8169 0000:01:00.0: firmware: agent loaded rtl_nic/rtl8168d-1.fw into memory
[ 102.845915] r8169 0000:01:00.0: eth0: link down
[ 102.846447] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 104.497739] r8169 0000:01:00.0: eth0: link up
[ 104.498248] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
** Model information
sys_vendor: MSI
product_name: MS-7636
product_version: 1.0
chassis_vendor: MSI
chassis_version: 1.0
bios_vendor: American Megatrends Inc.
bios_version: V1.10
board_vendor: MSI
board_name: H55M-E33(MS-7636)
board_version: 1.0
** Loaded modules:
bnep
rfcomm
bluetooth
rfkill
crc16
cpufreq_conservative
cpufreq_userspace
cpufreq_stats
cpufreq_powersave
parport_pc
ppdev
lp
parport
fuse
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
pcrypt
f71882fg
loop
i2c_dev
raid1
saa7134_alsa
kvm_intel
kvm
tda1004x
saa7134_dvb
videobuf_dvb
dvb_core
tda827x
snd_usb_audio
tda8290
snd_hda_codec_hdmi
snd_hda_codec_realtek
ir_lirc_codec
lirc_dev
ir_mce_kbd_decoder
ir_sony_decoder
tuner
snd_hda_intel
snd_hda_codec
ir_jvc_decoder
snd_usbmidi_lib
ir_rc6_decoder
snd_hwdep
snd_seq_midi
snd_seq_midi_event
ir_rc5_decoder
snd_rawmidi
snd_seq
snd_pcm
ir_nec_decoder
tpm_infineon
snd_seq_device
saa7134
snd_page_alloc
snd_timer
snd
i915
soundcore
pl2303
tveeprom
videobuf_dma_sg
videobuf_core
v4l2_common
usbserial
video
videodev
v4l2_compat_ioctl32
media
drm_kms_helper
drm
i2c_algo_bit
rc_core
pcspkr
psmouse
acpi_cpufreq
mperf
evdev
i2c_i801
coretemp
serio_raw
i2c_core
iTCO_wdt
iTCO_vendor_support
tpm_tis
tpm
tpm_bios
processor
button
thermal_sys
ext3
mbcache
jbd
sha256_generic
dm_crypt
dm_mod
raid10
md_mod
microcode
sd_mod
crc_t10dif
usbhid
usb_storage
hid
sg
sr_mod
cdrom
ahci
ata_generic
libahci
crc32c_intel
ghash_clmulni_intel
pata_jmicron
aesni_intel
aes_x86_64
libata
scsi_mod
ehci_hcd
aes_generic
cryptd
r8169
mii
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM Controller [8086:0040] (rev 18)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0042] (rev 18) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 42
Region 0: Memory at fb800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at cc00 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:16.0 Communication controller [0780]: Intel Corporation 5 Series/3400 Series Chipset HECI Controller [8086:3b64] (rev 06)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fbdfa000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:1a.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 06) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbdf8000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio [8086:3b56] (rev 06)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at fbdf4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 [8086:3b42] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fbe00000-fbefffff
Prefetchable memory behind bridge: 00000000faf00000-00000000faffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 [8086:3b46] (rev 06) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: c0000000-c01fffff
Prefetchable memory behind bridge: 00000000c0200000-00000000c03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 06) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fbdf2000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a6) (prog-if 01 [Subtractive decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: fbf00000-fbffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 5 Series Chipset LPC Interface Controller [8086:3b06] (rev 06)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller [8086:3b22] (rev 06) (prog-if 01 [AHCI 1.0])
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 41
Region 0: I/O ports at c880 [size=8]
Region 1: I/O ports at c800 [size=4]
Region 2: I/O ports at c480 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c080 [size=32]
Region 5: Memory at fbdf0000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 06)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbdee000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 03)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at d800 [size=256]
Region 2: Memory at fafff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at faff8000 (64-bit, prefetchable) [size=16K]
Expansion ROM at fbee0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
02:00.0 IDE interface [0101]: JMicron Technology Corp. JMB368 IDE controller [197b:2368] (prog-if 85 [Master SecO PriO])
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7636]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e880 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e480 [size=4]
Region 4: I/O ports at e400 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_jmicron
03:00.0 Multimedia controller [0480]: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder [1131:7133] (rev d1)
Subsystem: TERRATEC Electronic GmbH Device [153b:1175]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (21000ns min, 8000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbfff800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: saa7134
ff:00.0 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers [8086:2c61] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:00.1 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture System Address Decoder [8086:2d01] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.0 Host bridge [0600]: Intel Corporation Core Processor QPI Link 0 [8086:2d10] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.1 Host bridge [0600]: Intel Corporation Core Processor QPI Physical 0 [8086:2d11] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.2 Host bridge [0600]: Intel Corporation Core Processor Reserved [8086:2d12] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.3 Host bridge [0600]: Intel Corporation Core Processor Reserved [8086:2d13] (rev 05)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 003: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port
Bus 001 Device 004: ID 1130:1620 Tenx Technology, Inc.
Bus 002 Device 003: ID 05e3:0716 Genesys Logic, Inc. USB 2.0 Multislot Card Reader/Writer
-- System Information:
Debian Release: 7.5
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-4-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.ISO-8859-1, LC_CTYPE=en_US.ISO-8859-1 (charmap=ISO-8859-1)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.2.0-4-amd64 suggests:
ii debian-kernel-handbook 1.0.15
ii extlinux 2:4.05+dfsg-6+deb7u1
ii grub-pc 1.99-27+deb7u2
ii lilo 1:23.2-4
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 0.36+wheezy.1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.36+wheezy.1
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
Reply to: