--- Begin Message ---
Subject: usb 2.0 hdd copy error
Package: linux-image-2.6.26-1-686
Version: 2.6.26-13
Severity: normal
*** Please type your report below this line ***
I have problems using a 640GB USB 2.0 mass storage device "store alu" from Toshiba with lenny (kernel 2.6.26-1-686). The device was formated with vfat. When I tried to copy files from it this lead to an error. As saving very large files is not possible with vfat and I needed this feature, i formated the harddisk with an ntfs partition. But the copy problem did not go away. When I try to copy larger files (happend for instance with something more than 4MB) the cpu gets busy, copying does not proceed at some point, the device can not be unmounted. The only way to stop this was putting the power of the usb device off. Dmesg reported the following:
[ 564.502023] usb 5-1: new high speed USB device using ehci_hcd and address 2
[ 564.637216] usb 5-1: configuration #1 chosen from 1 choice
[ 564.648994] usb 5-1: New USB device found, idVendor=0930, idProduct=0b09
[ 564.649031] usb 5-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 564.649038] usb 5-1: Product: USB 3.5"-HDD
[ 564.649043] usb 5-1: Manufacturer: TOSHIBA
[ 564.649048] usb 5-1: SerialNumber: 0013F007
[ 564.823762] Initializing USB Mass Storage driver...
[ 564.824985] scsi0 : SCSI emulation for USB Mass Storage devices
[ 564.826309] usbcore: registered new interface driver usb-storage
[ 564.826700] USB Mass Storage support registered.
[ 564.873554] usb-storage: device found at 2
[ 564.873935] usb-storage: waiting for device to settle before scanning
[ 569.874337] usb-storage: device scan complete
[ 569.880322] scsi 0:0:0:0: Direct-Access TOSHIBA USB 3.5"-HDD 100 PQ: 0 ANSI: 2
[ 569.999406] Driver 'sd' needs updating - please use bus_type methods
[ 570.001079] sd 0:0:0:0: [sda] 1250263728 512-byte hardware sectors (640135 MB)
[ 570.004128] sd 0:0:0:0: [sda] Write Protect is off
[ 570.004518] sd 0:0:0:0: [sda] Mode Sense: 38 00 00 00
[ 570.004747] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 570.007424] sd 0:0:0:0: [sda] 1250263728 512-byte hardware sectors (640135 MB)
[ 570.009798] sd 0:0:0:0: [sda] Write Protect is off
[ 570.009814] sd 0:0:0:0: [sda] Mode Sense: 38 00 00 00
[ 570.009821] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 570.009832] sda: sda1
[ 570.023425] sd 0:0:0:0: [sda] Attached SCSI disk
[ 609.623029] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[ 639.848043] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[ 670.073064] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[ 700.298030] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[ 730.523065] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[ 760.748057] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[ 760.871027] sd 0:0:0:0: [sda] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK
[ 760.871027] end_request: I/O error, dev sda, sector 443815
[ 760.871027] Buffer I/O error on device sda1, logical block 55469
[ 760.872442] Buffer I/O error on device sda1, logical block 55470
[ 760.872456] Buffer I/O error on device sda1, logical block 55471
[ 760.872465] Buffer I/O error on device sda1, logical block 55472
[ 760.872473] Buffer I/O error on device sda1, logical block 55473
[ 760.872481] Buffer I/O error on device sda1, logical block 55474
[ 760.872489] Buffer I/O error on device sda1, logical block 55475
[ 760.872497] Buffer I/O error on device sda1, logical block 55476
[ 760.872505] Buffer I/O error on device sda1, logical block 55477
[ 760.872513] Buffer I/O error on device sda1, logical block 55478
[ 790.974073] usb 5-1: reset high speed USB device using ehci_hcd and address 2
[ 821.199034] usb 5-1: reset high speed USB device using ehci_hcd and address 2
This error also occured using Ubuntu 8.10 and an older Kanotix. For detailed information from Lenny I compiled a kernel with usb and usb mass storage debugging enabled. In addition I removed some unused drivers from the kernel configuration. Dmesg reported the following when I put the power on the USB device on:
[ 403.300997] usb usb3: usb resume
[ 403.300997] ehci_hcd 0000:00:0c.2: resume root hub
[ 403.400417] hub 3-0:1.0: hub_resume
[ 403.400727] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
[ 403.400963] hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 403.401009] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT
[ 403.401009] hub 3-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
[ 403.504027] hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
[ 403.555276] ehci_hcd 0000:00:0c.2: port 1 high speed
[ 403.555293] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 403.606051] usb 3-1: new high speed USB device using ehci_hcd and address 2
[ 403.658290] ehci_hcd 0000:00:0c.2: port 1 high speed
[ 403.658309] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 403.723002] usb 3-1: default language 0x0409
[ 403.741420] usb 3-1: uevent
[ 403.758600] usb 3-1: usb_probe_device
[ 403.758615] usb 3-1: configuration #1 chosen from 1 choice
[ 403.762742] usb 3-1: adding 3-1:1.0 (config #1, interface 0)
[ 403.762843] usb 3-1:1.0: uevent
[ 403.763967] drivers/usb/core/inode.c: creating file '002'
[ 403.764104] usb 3-1: New USB device found, idVendor=0930, idProduct=0b09
[ 403.764111] usb 3-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 403.764117] usb 3-1: Product: USB 3.5"-HDD
[ 403.764121] usb 3-1: Manufacturer: TOSHIBA
[ 403.764125] usb 3-1: SerialNumber: 0013F007
[ 403.908253] Initializing USB Mass Storage driver...
[ 403.908723] usb-storage 3-1:1.0: usb_probe_interface
[ 403.908980] usb-storage 3-1:1.0: usb_probe_interface - got id
[ 403.909221] usb-storage: USB Mass Storage device detected
[ 403.910037] usb-storage: -- associate_dev
[ 403.910393] usb-storage: Vendor: 0x0930, Product: 0x0b09, Revision: 0x0112
[ 403.910585] usb-storage: Interface Subclass: 0x06, Protocol: 0x50
[ 403.910777] usb-storage: Transport: Bulk
[ 403.910961] usb-storage: Protocol: Transparent SCSI
[ 403.911281] scsi0 : SCSI emulation for USB Mass Storage devices
[ 403.912313] usb-storage: *** thread sleeping.
[ 403.912849] usbcore: registered new interface driver usb-storage
[ 403.913211] USB Mass Storage support registered.
[ 403.958073] usb-storage: device found at 2
[ 403.958456] usb-storage: waiting for device to settle before scanning
...
Now the CPU was very busy. I did not start copying yet.
...
[ 530.356639] usb-storage: storage_pre_reset
[ 530.407301] ehci_hcd 0000:00:0c.2: port 1 high speed
[ 530.407320] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 530.458049] usb 3-1: reset high speed USB device using ehci_hcd and address 2
[ 530.510311] ehci_hcd 0000:00:0c.2: port 1 high speed
[ 530.510328] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 530.581068] usb-storage: storage_post_reset
[ 530.581068] usb-storage: usb_reset_composite_device returns 0
[ 530.581068] usb-storage: scsi command aborted
[ 530.581068] usb-storage: *** thread sleeping.
[ 530.581068] usb-storage: queuecommand called
[ 530.581068] usb-storage: *** thread awakened.
[ 530.581068] usb-storage: Command TEST_UNIT_READY (6 bytes)
[ 530.581068] usb-storage: 00 00 00 00 00 00
[ 530.581068] usb-storage: Bulk Command S 0x43425355 T 0x39 L 0 F 0 Trg 0 LUN 0 CL 6
[ 530.581068] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 530.581068] usb-storage: Status code 0; transferred 31/31
[ 530.581068] usb-storage: -- transfer complete
[ 530.581068] usb-storage: Bulk command transfer result=0
[ 530.581068] usb-storage: Attempting to get CSW...
[ 530.581068] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 530.581068] usb-storage: Status code 0; transferred 13/13
[ 530.581068] usb-storage: -- transfer complete
[ 530.581068] usb-storage: Bulk status result = 0
[ 530.581068] usb-storage: Bulk Status S 0x53425355 T 0x39 R 0 Stat 0x0
[ 530.581068] usb-storage: scsi cmd done, result=0x0
[ 530.581068] usb-storage: *** thread sleeping.
[ 530.581068] usb-storage: queuecommand called
[ 530.581068] usb-storage: *** thread awakened.
[ 530.581068] usb-storage: Command READ_10 (10 bytes)
[ 530.581068] usb-storage: 28 00 00 00 00 61 00 00 3e 00
[ 530.581068] usb-storage: Bulk Command S 0x43425355 T 0x3a L 31744 F 128 Trg 0 LUN 0 CL 10
[ 530.581068] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 530.581068] usb-storage: Status code 0; transferred 31/31
[ 530.581068] usb-storage: -- transfer complete
[ 530.581068] usb-storage: Bulk command transfer result=0
[ 530.581068] usb-storage: usb_stor_bulk_transfer_sglist: xfer 31744 bytes, 8 entries
[ 560.581027] usb-storage: command_abort called
[ 560.581044] usb-storage: usb_stor_stop_transport called
[ 560.581048] usb-storage: -- cancelling sg request
[ 560.581492] usb-storage: Status code -104; transferred 0/31744
[ 560.581499] usb-storage: -- transfer cancelled
[ 560.581505] usb-storage: Bulk data transfer result 0x4
[ 560.581509] usb-storage: -- command was aborted
[ 560.581519] usb-storage: storage_pre_reset
[ 560.632274] ehci_hcd 0000:00:0c.2: port 1 high speed
[ 560.632292] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 560.683053] usb 3-1: reset high speed USB device using ehci_hcd and address 2
[ 560.735285] ehci_hcd 0000:00:0c.2: port 1 high speed
[ 560.735303] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 560.806044] usb-storage: storage_post_reset
[ 560.806044] usb-storage: usb_reset_composite_device returns 0
[ 560.806044] usb-storage: scsi command aborted
[ 560.806044] usb-storage: *** thread sleeping.
[ 560.806044] usb-storage: queuecommand called
[ 560.806044] usb-storage: *** thread awakened.
[ 560.806044] usb-storage: Command TEST_UNIT_READY (6 bytes)
[ 560.806044] usb-storage: 00 00 00 00 00 00
[ 560.806044] usb-storage: Bulk Command S 0x43425355 T 0x3b L 0 F 0 Trg 0 LUN 0 CL 6
[ 560.806044] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 560.806044] usb-storage: Status code 0; transferred 31/31
[ 560.806044] usb-storage: -- transfer complete
[ 560.806044] usb-storage: Bulk command transfer result=0
[ 560.806044] usb-storage: Attempting to get CSW...
[ 560.806044] usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
[ 560.806044] usb-storage: Status code 0; transferred 13/13
[ 560.806044] usb-storage: -- transfer complete
[ 560.806044] usb-storage: Bulk status result = 0
[ 560.806044] usb-storage: Bulk Status S 0x53425355 T 0x3b R 0 Stat 0x0
[ 560.806044] usb-storage: scsi cmd done, result=0x0
[ 560.806044] usb-storage: *** thread sleeping.
[ 560.806044] sd 0:0:0:0: [sda] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK,SUGGEST_OK
[ 560.806044] end_request: I/O error, dev sda, sector 97
[ 560.806044] Buffer I/O error on device sda1, logical block 17
[ 560.806044] Buffer I/O error on device sda1, logical block 18
[ 560.806044] Buffer I/O error on device sda1, logical block 19
[ 560.806044] Buffer I/O error on device sda1, logical block 20
[ 560.806044] Buffer I/O error on device sda1, logical block 21
[ 560.806044] Buffer I/O error on device sda1, logical block 22
[ 560.806044] Buffer I/O error on device sda1, logical block 23
[ 560.806044] Buffer I/O error on device sda1, logical block 24
[ 560.806044] Buffer I/O error on device sda1, logical block 25
[ 560.806044] Buffer I/O error on device sda1, logical block 26
[ 560.806044] usb-storage: queuecommand called
[ 560.806044] usb-storage: *** thread awakened.
[ 560.806044] usb-storage: Command READ_10 (10 bytes)
[ 560.806044] usb-storage: 28 00 4a 85 6e bf 00 00 02 00
[ 560.806044] usb-storage: Bulk Command S 0x43425355 T 0x3c L 1024 F 128 Trg 0 LUN 0 CL 10
[ 560.806044] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 560.807416] usb-storage: Status code 0; transferred 31/31
[ 560.807424] usb-storage: -- transfer complete
[ 560.807428] usb-storage: Bulk command transfer result=0
[ 560.807434] usb-storage: usb_stor_bulk_transfer_sglist: xfer 1024 bytes, 1 entries
[ 574.062994] ehci_hcd 0000:00:0c.2: devpath 1 ep1in 3strikes
[ 574.062994] hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0002
[ 574.062994] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001002 POWER sig=se0 CSC
[ 574.062994] hub 3-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
[ 574.062994] usb 3-1: USB disconnect, address 2
[ 574.062994] usb 3-1: unregistering device
[ 574.062994] usb 3-1: usb_disable_device nuking all URBs
[ 574.062994] usb 3-1: unregistering interface 3-1:1.0
[ 574.062994] usb-storage: storage_disconnect() called
[ 574.062994] usb-storage: usb_stor_stop_transport called
[ 574.062994] usb-storage: -- cancelling sg request
[ 574.106566] usb-storage: Status code -71; transferred 0/1024
[ 574.106576] usb-storage: -- unknown error
[ 574.106581] usb-storage: Bulk data transfer result 0x4
[ 574.106585] usb-storage: -- transport indicates error, resetting
[ 574.106732] sd 0:0:0:0: [sda] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
[ 574.106742] end_request: I/O error, dev sda, sector 1250258623
[ 574.106753] __ratelimit: 21 messages suppressed
[ 574.106759] Buffer I/O error on device sda1, logical block 625129280
[ 574.107434] usb-storage: -- usb_stor_release_resources
[ 574.107441] usb-storage: -- sending exit command to thread
[ 574.107541] Buffer I/O error on device sda1, logical block 625129280
[ 574.108585] usb-storage: unable to lock device for reset: -19
[ 574.108597] usb-storage: usb_stor_Bulk_reset called
[ 574.108602] usb-storage: No reset during disconnect
[ 574.108607] usb-storage: *** thread sleeping.
[ 574.108612] usb-storage: *** thread awakened.
[ 574.108615] usb-storage: -- exiting
[ 574.108635] usb-storage: -- dissociate_dev
[ 574.108746] usb 3-1:1.0: uevent
[ 574.109121] usb 3-1: uevent
[ 574.213047] hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
[ 576.213036] hub 3-0:1.0: hub_suspend
[ 576.213060] usb usb3: bus auto-suspend
[ 576.213067] ehci_hcd 0000:00:0c.2: suspend root hub
At the end I put the power of the device off. In a second attempt a 37MB file was succesfully copied. This was never possible with the original Lenny kernel. Now I tried a 14GB file. Here the described behaviour appeared again. I had to put the power off at the end:
[ 1958.866535] usb-storage: Bulk status result = 0
[ 1958.866540] usb-storage: Bulk Status S 0x53425355 T 0x9b1 R 0 Stat 0x0
[ 1958.866547] usb-storage: scsi cmd done, result=0x0
[ 1958.866557] usb-storage: *** thread sleeping.
[ 1958.866617] usb-storage: queuecommand called
[ 1958.866641] usb-storage: *** thread awakened.
[ 1958.866648] usb-storage: Command READ_10 (10 bytes)
[ 1958.866651] usb-storage: 28 00 00 48 b7 27 00 00 f0 00
[ 1958.866668] usb-storage: Bulk Command S 0x43425355 T 0x9b2 L 122880 F 128 Trg 0 LUN 0 CL 10
[ 1958.866673] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 1958.866798] usb-storage: Status code 0; transferred 31/31
[ 1958.866802] usb-storage: -- transfer complete
[ 1958.866806] usb-storage: Bulk command transfer result=0
[ 1958.866811] usb-storage: usb_stor_bulk_transfer_sglist: xfer 122880 bytes, 30 entries
[ 1958.868924] ehci_hcd 0000:00:0c.2: devpath 1 ep1in 3strikes
[ 1958.868988] usb-storage: Status code -71; transferred 78848/122880
[ 1958.868993] usb-storage: -- unknown error
[ 1958.868998] usb-storage: Bulk data transfer result 0x4
[ 1958.869003] usb-storage: -- transport indicates error, resetting
[ 1958.869042] usb-storage: storage_pre_reset
[ 1958.920391] ehci_hcd 0000:00:0c.2: port 1 high speed
[ 1958.920405] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 1958.971068] usb 3-1: reset high speed USB device using ehci_hcd and address 4
[ 1959.023279] ehci_hcd 0000:00:0c.2: port 1 high speed
[ 1959.023293] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT
[ 1959.094203] usb-storage: storage_post_reset
[ 1959.094219] usb-storage: usb_reset_composite_device returns 0
[ 1959.094225] usb-storage: scsi cmd done, result=0x70000
[ 1959.094237] usb-storage: *** thread sleeping.
[ 1959.094268] usb-storage: queuecommand called
[ 1959.094280] usb-storage: *** thread awakened.
[ 1959.094287] usb-storage: Command READ_10 (10 bytes)
[ 1959.094290] usb-storage: 28 00 00 48 b7 27 00 00 f0 00
[ 1959.094308] usb-storage: Bulk Command S 0x43425355 T 0x9b3 L 122880 F 128 Trg 0 LUN 0 CL 10
[ 1959.094314] usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
[ 1959.094431] usb-storage: Status code 0; transferred 31/31
[ 1959.094436] usb-storage: -- transfer complete
[ 1959.094440] usb-storage: Bulk command transfer result=0
[ 1959.094446] usb-storage: usb_stor_bulk_transfer_sglist: xfer 122880 bytes, 30 entries
[ 1973.251022] ehci_hcd 0000:00:0c.2: devpath 1 ep1in 3strikes
[ 1973.251022] hub 3-0:1.0: state 7 ports 4 chg 0000 evt 0002
[ 1973.251022] ehci_hcd 0000:00:0c.2: GetStatus port 1 status 001002 POWER sig=se0 CSC
[ 1973.251022] hub 3-0:1.0: port 1, status 0100, change 0001, 12 Mb/s
[ 1973.251022] usb 3-1: USB disconnect, address 4
[ 1973.251022] usb 3-1: unregistering device
[ 1973.251022] usb 3-1: usb_disable_device nuking all URBs
[ 1973.251022] usb 3-1: unregistering interface 3-1:1.0
[ 1973.251022] usb-storage: storage_disconnect() called
[ 1973.251022] usb-storage: usb_stor_stop_transport called
[ 1973.251022] usb-storage: -- cancelling sg request
[ 1973.255194] usb-storage: Status code -71; transferred 0/122880
[ 1973.255204] usb-storage: -- unknown error
[ 1973.255209] usb-storage: Bulk data transfer result 0x4
[ 1973.255213] usb-storage: -- transport indicates error, resetting
[ 1973.255375] sd 2:0:0:0: [sda] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
[ 1973.255386] end_request: I/O error, dev sda, sector 4765479
[ 1973.255396] __ratelimit: 28 messages suppressed
[ 1973.255402] Buffer I/O error on device sda1, logical block 595677
[ 1973.255418] Buffer I/O error on device sda1, logical block 595678
[ 1973.255426] Buffer I/O error on device sda1, logical block 595679
[ 1973.255433] Buffer I/O error on device sda1, logical block 595680
[ 1973.255440] Buffer I/O error on device sda1, logical block 595681
[ 1973.255447] Buffer I/O error on device sda1, logical block 595682
[ 1973.255453] Buffer I/O error on device sda1, logical block 595683
[ 1973.255460] Buffer I/O error on device sda1, logical block 595684
[ 1973.255467] Buffer I/O error on device sda1, logical block 595685
[ 1973.255473] Buffer I/O error on device sda1, logical block 595686
[ 1973.255527] usb-storage: queuecommand called
[ 1973.255531] usb-storage: Fail command during disconnect
[ 1973.255541] sd 2:0:0:0: [sda] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK
[ 1973.255549] end_request: I/O error, dev sda, sector 4765719
[ 1973.322380] usb-storage: unable to lock device for reset: -19
[ 1973.322393] usb-storage: usb_stor_Bulk_reset called
[ 1973.322397] usb-storage: No reset during disconnect
[ 1973.322403] usb-storage: *** thread sleeping.
[ 1973.324068] usb-storage: -- usb_stor_release_resources
[ 1973.324074] usb-storage: -- sending exit command to thread
[ 1973.324100] usb-storage: *** thread awakened.
[ 1973.324104] usb-storage: -- exiting
[ 1973.324153] usb-storage: -- dissociate_dev
[ 1973.324185] usb 3-1:1.0: uevent
[ 1973.324496] usb 3-1: uevent
[ 1973.428084] hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
lspci output:
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:0c.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62)
00:0c.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 62)
00:0c.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 65)
00:0d.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 23)
00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 23)
00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:00.0 VGA compatible controller: nVidia Corporation NV34 [GeForce FX 5200] (rev a1)
lsusb output:
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 0582:0005 Roland Corp. Edirol UM-2 MIDI Adapter
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 005: ID 0930:0b09 Toshiba Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
The device is connected using a USB 2.0 PCI card. When i remove the USB 2.0 kernel module copying works succesfully using USB 1.1.
-- Package-specific info:
-- System Information:
Debian Release: 5.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26.audioslim (SMP w/1 CPU core; PREEMPT)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-1-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-686/preinst/abort-overwrite-2.6.26-1-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-686/postinst/bootloader-error-2.6.26-1-686:
linux-image-2.6.26-1-686/postinst/depmod-error-initrd-2.6.26-1-686: false
linux-image-2.6.26-1-686/prerm/removing-running-kernel-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-system-map-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/abort-install-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-686/preinst/bootloader-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/prerm/would-invalidate-boot-loader-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/elilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-686/postinst/old-dir-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/create-kimage-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/lilo-initrd-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/old-initrd-link-2.6.26-1-686: true
linux-image-2.6.26-1-686/preinst/overwriting-modules-2.6.26-1-686: true
linux-image-2.6.26-1-686/postinst/depmod-error-2.6.26-1-686: false
linux-image-2.6.26-1-686/postinst/bootloader-test-error-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/failed-to-move-modules-2.6.26-1-686:
linux-image-2.6.26-1-686/preinst/initrd-2.6.26-1-686:
#adBox3 {display:none;}
--- End Message ---