Bug#706131: linux-image-3.2.0-4-amd64: MegaRAID SAS 2108 (Dell PERC H700) FW in FAULT state with old BIOS
Package: src:linux
Version: 3.2.41-2
Severity: important
This is already solved and just for your information. Feel free to close/
reassign/lower the severity as you like.
We run a ton of Dell R610 with the PERC H700 RAID controller, which is a
relabeled LSI MegaRAID SAS 2108. They have been running for some years
with OpenSUSE and SLES and not caused any issues. I'm quite sure we also
booted Squeeze sucessfully on it, but I'm going to verify that. They had
never received any firmware update, which made the main BIOS version
2.1.15 and the LSI BIOS 12.3.
Wheezy (both RC1 and daily from April 22nd) could not be installed,
because it did not detect any disk. dmesg showed this (typed from
a screenshot, excuse any errors)
megasas: 00.00.06.12-rc1 Wed. Oct. 5 17:00:00 PDT 2011
megasas: 0x1000:0x0079:0x1028:0x1f17: bus 3:slot 0:func 0
megaraid_sas: 0000:03:00.0: setting latency timer to 64
megasas: Waiting for FW to come to ready state
megasas: FW in FAULT state!!
Googling for this error revealed a metric ton of similar reports.
Some reported breakage in PCIe ASPM, some in MSI handling, some
other errors
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1091263
http://www.mail-archive.com/linux-scsi@vger.kernel.org/msg18002.html
http://lkml.indiana.edu/hypermail/linux/kernel/1204.1/03020.html
http://bugs.centos.org/view.php?id=6140
None of those workarounds listed in the bugs worked for us. After a
2-hour session upgrading all the firmware on the system (which
bumped the BIOS to 6.something and LSI to 12.10) it worked just fine.
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-15) ) #1 SMP Debian 3.2.41-2
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=/dev/mapper/voip12-root ro quiet
** Not tainted
** Kernel log:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-15) ) #1 SMP Debian 3.2.41-2
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=/dev/mapper/voip12-root ro quiet
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cf379000 (usable)
[ 0.000000] BIOS-e820: 00000000cf379000 - 00000000cf38f000 (reserved)
[ 0.000000] BIOS-e820: 00000000cf38f000 - 00000000cf3ce000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cf3ce000 - 00000000d0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000630000000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] DMI: Dell Inc. PowerEdge R610/0F0XJ6, BIOS 6.3.0 07/24/2012
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x630000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-D3FFF write-back
[ 0.000000] D4000-EBFFF uncachable
[ 0.000000] EC000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask FF80000000 write-back
[ 0.000000] 1 base 0080000000 mask FFC0000000 write-back
[ 0.000000] 2 base 00C0000000 mask FFF0000000 write-back
[ 0.000000] 3 base 0100000000 mask FF00000000 write-back
[ 0.000000] 4 base 0200000000 mask FE00000000 write-back
[ 0.000000] 5 base 0400000000 mask FE00000000 write-back
[ 0.000000] 6 base 0600000000 mask FFE0000000 write-back
[ 0.000000] 7 base 0620000000 mask FFF0000000 write-back
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 00000000d0000000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0xcf379 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000fe710] fe710
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 20480
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: 0000000000000000-00000000cf379000
[ 0.000000] 0000000000 - 00c0000000 page 1G
[ 0.000000] 00c0000000 - 00cf200000 page 2M
[ 0.000000] 00cf200000 - 00cf379000 page 4k
[ 0.000000] kernel direct mapping tables up to cf379000 @ 1fffd000-20000000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000630000000
[ 0.000000] 0100000000 - 0600000000 page 1G
[ 0.000000] 0600000000 - 0630000000 page 2M
[ 0.000000] kernel direct mapping tables up to 630000000 @ cf377000-cf379000
[ 0.000000] RAMDISK: 36b10000 - 37580000
[ 0.000000] ACPI: RSDP 00000000000f1150 00024 (v02 DELL )
[ 0.000000] ACPI: XSDT 00000000000f1254 0009C (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: FACP 00000000cf3b3f9c 000F4 (v03 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: DSDT 00000000cf38f000 03DD0 (v01 DELL PE_SC3 00000001 INTL 20050624)
[ 0.000000] ACPI: FACS 00000000cf3b6000 00040
[ 0.000000] ACPI: APIC 00000000cf3b3478 0015E (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: SPCR 00000000cf3b35d8 00050 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: HPET 00000000cf3b362c 00038 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: DMAR 00000000cf3b3668 001A8 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: MCFG 00000000cf3b38c4 0003C (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: WD__ 00000000cf3b3904 00134 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: SLIC 00000000cf3b3a3c 00024 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: ERST 00000000cf392f70 00270 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: HEST 00000000cf3931e0 003A8 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: BERT 00000000cf392dd0 00030 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: EINJ 00000000cf392e00 00170 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: SRAT 00000000cf3b3bc0 00370 (v01 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: TCPA 00000000cf3b3f34 00064 (v02 DELL PE_SC3 00000001 DELL 00000001)
[ 0.000000] ACPI: SSDT 00000000cf3b7000 06C0C (v01 INTEL PPM RCM 80000001 INTL 20061109)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] SRAT: PXM 1 -> APIC 0x20 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x00 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x22 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x02 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x24 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x04 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x30 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x10 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x32 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x12 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x34 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x14 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x21 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x01 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x23 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x03 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x25 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x05 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x31 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x11 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x33 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x13 -> Node 1
[ 0.000000] SRAT: PXM 1 -> APIC 0x35 -> Node 0
[ 0.000000] SRAT: PXM 2 -> APIC 0x15 -> Node 1
[ 0.000000] SRAT: Node 1 PXM 2 0-d0000000
[ 0.000000] SRAT: Node 1 PXM 2 100000000-330000000
[ 0.000000] SRAT: Node 0 PXM 1 330000000-630000000
[ 0.000000] NUMA: Node 1 [0,d0000000) + [100000000,330000000) -> [0,330000000)
[ 0.000000] Initmem setup node 0 0000000330000000-0000000630000000
[ 0.000000] NODE_DATA [000000062fffb000 - 000000062fffffff]
[ 0.000000] Initmem setup node 1 0000000000000000-0000000330000000
[ 0.000000] NODE_DATA [000000032fffb000 - 000000032fffffff]
[ 0.000000] [ffffea000b280000-ffffea000b3fffff] potential offnode page_structs
[ 0.000000] [ffffea0000000000-ffffea000b3fffff] PMD -> [ffff880323e00000-ffff88032e7fffff] on node 1
[ 0.000000] [ffffea000b400000-ffffea0015bfffff] PMD -> [ffff880623600000-ffff88062ddfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00630000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[4] active PFN ranges
[ 0.000000] 1: 0x00000010 -> 0x0000009e
[ 0.000000] 1: 0x00000100 -> 0x000cf379
[ 0.000000] 1: 0x00100000 -> 0x00330000
[ 0.000000] 0: 0x00330000 -> 0x00630000
[ 0.000000] On node 0 totalpages: 3145728
[ 0.000000] Normal zone: 43008 pages used for memmap
[ 0.000000] Normal zone: 3102720 pages, LIFO batch:31
[ 0.000000] On node 1 totalpages: 3142407
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 5 pages reserved
[ 0.000000] DMA zone: 3921 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 830385 pages, LIFO batch:31
[ 0.000000] Normal zone: 31360 pages used for memmap
[ 0.000000] Normal zone: 2262400 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x20] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x22] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x24] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x30] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x10] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x09] lapic_id[0x32] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0a] lapic_id[0x12] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0b] lapic_id[0x34] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0c] lapic_id[0x14] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0d] lapic_id[0x21] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0e] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x0f] lapic_id[0x23] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x10] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x11] lapic_id[0x25] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x12] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x13] lapic_id[0x31] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x14] lapic_id[0x11] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x15] lapic_id[0x33] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x16] lapic_id[0x13] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x17] lapic_id[0x35] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x18] lapic_id[0x15] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x19] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1a] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1b] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1c] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1d] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1e] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x1f] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x20] lapic_id[0xff] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec80000] gsi_base[32])
[ 0.000000] IOAPIC[1]: apic_id 1, version 32, address 0xfec80000, GSI 32-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] SMP: Allowing 32 CPUs, 8 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 72
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000cf379000 - 00000000cf38f000
[ 0.000000] PM: Registered nosave memory: 00000000cf38f000 - 00000000cf3ce000
[ 0.000000] PM: Registered nosave memory: 00000000cf3ce000 - 00000000d0000000
[ 0.000000] PM: Registered nosave memory: 00000000d0000000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fe000000
[ 0.000000] PM: Registered nosave memory: 00000000fe000000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at d0000000 (gap: d0000000:10000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:32 nr_node_ids:2
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88032fc00000 s82944 r8192 d23552 u131072
[ 0.000000] pcpu-alloc: s82944 r8192 d23552 u131072 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 00 02 04 06 08 10 12 14 16 18 20 22 24 26 28 30
[ 0.000000] pcpu-alloc: [1] 01 03 05 07 09 11 13 15 17 19 21 23 25 27 29 31
[ 0.000000] Built 2 zonelists in Zone order, mobility grouping on. Total pages: 6199426
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=/dev/mapper/voip12-root ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 24717456k/25952256k available (3420k kernel code, 799716k absent, 435084k reserved, 3318k data, 576k init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:33024 nr_irqs:1480 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.004000] Detected 2659.750 MHz processor.
[ 0.000007] Calibrating delay loop (skipped), value calculated using timer frequency.. 5319.50 BogoMIPS (lpj=10639000)
[ 0.000011] pid_max: default: 32768 minimum: 301
[ 0.000061] Security Framework initialized
[ 0.000065] AppArmor: AppArmor disabled by boot time parameter
[ 0.001680] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes)
[ 0.007679] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.010340] Mount-cache hash table entries: 256
[ 0.010508] Initializing cgroup subsys cpuacct
[ 0.010516] Initializing cgroup subsys memory
[ 0.010533] Initializing cgroup subsys devices
[ 0.010535] Initializing cgroup subsys freezer
[ 0.010537] Initializing cgroup subsys net_cls
[ 0.010539] Initializing cgroup subsys blkio
[ 0.010545] Initializing cgroup subsys perf_event
[ 0.010582] CPU: Physical Processor ID: 1
[ 0.010584] CPU: Processor Core ID: 0
[ 0.010588] mce: CPU supports 9 MCE banks
[ 0.010599] CPU0: Thermal monitoring enabled (TM1)
[ 0.010606] using mwait in idle threads.
[ 0.010928] ACPI: Core revision 20110623
[ 0.013151] DMAR: Host address width 40
[ 0.013153] DMAR: DRHD base: 0x000000fed90000 flags: 0x1
[ 0.013161] IOMMU 0: reg_base_addr fed90000 ver 1:0 cap c90780106f0462 ecap f020fe
[ 0.013163] DMAR: RMRR base: 0x000000cf4c8000 end: 0x000000cf4dffff
[ 0.013165] DMAR: RMRR base: 0x000000cf4b1000 end: 0x000000cf4bffff
[ 0.013166] DMAR: RMRR base: 0x000000cf4a1000 end: 0x000000cf4a1fff
[ 0.013168] DMAR: RMRR base: 0x000000cf4a3000 end: 0x000000cf4a3fff
[ 0.013170] DMAR: RMRR base: 0x000000cf4a5000 end: 0x000000cf4a5fff
[ 0.013171] DMAR: RMRR base: 0x000000cf4a7000 end: 0x000000cf4a7fff
[ 0.013174] DMAR: RMRR base: 0x000000cf4c0000 end: 0x000000cf4c0fff
[ 0.013175] DMAR: RMRR base: 0x000000cf4c2000 end: 0x000000cf4c2fff
[ 0.013177] DMAR: ATSR flags: 0x0
[ 0.013278] IOAPIC id 0 under DRHD base 0xfed90000 IOMMU 0
[ 0.013279] IOAPIC id 1 under DRHD base 0xfed90000 IOMMU 0
[ 0.013445] Enabled IRQ remapping in xapic mode
[ 0.013450] Switched APIC routing to physical flat.
[ 0.014011] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.053592] CPU0: Intel(R) Xeon(R) CPU X5650 @ 2.67GHz stepping 02
[ 0.160624] Performance Events: PEBS fmt1+, Westmere events, Intel PMU driver.
[ 0.160631] ... version: 3
[ 0.160632] ... bit width: 48
[ 0.160633] ... generic registers: 4
[ 0.160634] ... value mask: 0000ffffffffffff
[ 0.160636] ... max period: 000000007fffffff
[ 0.160637] ... fixed-purpose events: 3
[ 0.160638] ... event mask: 000000070000000f
[ 0.161128] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.161280] Booting Node 1, Processors #1
[ 0.161282] smpboot cpu 1: start_ip = 99000
[ 0.268449] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.268548] Ok.
[ 0.268549] Booting Node 0, Processors #2
[ 0.268550] smpboot cpu 2: start_ip = 99000
[ 0.376225] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.376396] Ok.
[ 0.376397] Booting Node 1, Processors #3
[ 0.376399] smpboot cpu 3: start_ip = 99000
[ 0.483856] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.483958] Ok.
[ 0.483959] Booting Node 0, Processors #4
[ 0.483960] smpboot cpu 4: start_ip = 99000
[ 0.591634] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.591806] Ok.
[ 0.591807] Booting Node 1, Processors #5
[ 0.591809] smpboot cpu 5: start_ip = 99000
[ 0.699366] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.699465] Ok.
[ 0.699466] Booting Node 0, Processors #6
[ 0.699467] smpboot cpu 6: start_ip = 99000
[ 0.807140] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.807302] Ok.
[ 0.807303] Booting Node 1, Processors #7
[ 0.807304] smpboot cpu 7: start_ip = 99000
[ 0.914762] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.914863] Ok.
[ 0.914864] Booting Node 0, Processors #8
[ 0.914866] smpboot cpu 8: start_ip = 99000
[ 1.022539] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.022701] Ok.
[ 1.022702] Booting Node 1, Processors #9
[ 1.022704] smpboot cpu 9: start_ip = 99000
[ 1.130260] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.130363] Ok.
[ 1.130364] Booting Node 0, Processors #10
[ 1.130366] smpboot cpu 10: start_ip = 99000
[ 1.238011] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.238177] Ok.
[ 1.238178] Booting Node 1, Processors #11
[ 1.238180] smpboot cpu 11: start_ip = 99000
[ 1.345748] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.345851] Ok.
[ 1.345852] Booting Node 0, Processors #12
[ 1.345854] smpboot cpu 12: start_ip = 99000
[ 1.453480] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.453646] Ok.
[ 1.453647] Booting Node 1, Processors #13
[ 1.453649] smpboot cpu 13: start_ip = 99000
[ 1.561208] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.561310] Ok.
[ 1.561311] Booting Node 0, Processors #14
[ 1.561313] smpboot cpu 14: start_ip = 99000
[ 1.668884] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.669051] Ok.
[ 1.669052] Booting Node 1, Processors #15
[ 1.669054] smpboot cpu 15: start_ip = 99000
[ 1.776666] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.776767] Ok.
[ 1.776768] Booting Node 0, Processors #16
[ 1.776770] smpboot cpu 16: start_ip = 99000
[ 1.884346] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.884505] Ok.
[ 1.884506] Booting Node 1, Processors #17
[ 1.884507] smpboot cpu 17: start_ip = 99000
[ 1.992064] NMI watchdog enabled, takes one hw-pmu counter.
[ 1.992165] Ok.
[ 1.992167] Booting Node 0, Processors #18
[ 1.992168] smpboot cpu 18: start_ip = 99000
[ 2.099851] NMI watchdog enabled, takes one hw-pmu counter.
[ 2.099999] Ok.
[ 2.100000] Booting Node 1, Processors #19
[ 2.100001] smpboot cpu 19: start_ip = 99000
[ 2.207508] NMI watchdog enabled, takes one hw-pmu counter.
[ 2.207614] Ok.
[ 2.207615] Booting Node 0, Processors #20
[ 2.207617] smpboot cpu 20: start_ip = 99000
[ 2.315291] NMI watchdog enabled, takes one hw-pmu counter.
[ 2.315448] Ok.
[ 2.315449] Booting Node 1, Processors #21
[ 2.315451] smpboot cpu 21: start_ip = 99000
[ 2.423007] NMI watchdog enabled, takes one hw-pmu counter.
[ 2.423107] Ok.
[ 2.423108] Booting Node 0, Processors #22
[ 2.423109] smpboot cpu 22: start_ip = 99000
[ 2.530681] NMI watchdog enabled, takes one hw-pmu counter.
[ 2.530849] Ok.
[ 2.530850] Booting Node 1, Processors #23
[ 2.530852] smpboot cpu 23: start_ip = 99000
[ 2.638407] NMI watchdog enabled, takes one hw-pmu counter.
[ 2.638425] Brought up 24 CPUs
[ 2.638427] Total of 24 processors activated (127678.69 BogoMIPS).
[ 2.666448] devtmpfs: initialized
[ 2.670910] print_constraints: dummy:
[ 2.671008] NET: Registered protocol family 16
[ 2.671112] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 2.671114] ACPI: bus type pci registered
[ 2.671186] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 2.671189] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 2.687637] PCI: Using configuration type 1 for base access
[ 2.689553] bio: create slab <bio-0> at 0
[ 2.689736] ACPI: Added _OSI(Module Device)
[ 2.689738] ACPI: Added _OSI(Processor Device)
[ 2.689739] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 2.689741] ACPI: Added _OSI(Processor Aggregator Device)
[ 2.690323] ACPI: EC: Look up EC in DSDT
[ 2.691224] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 2.694861] ACPI: Interpreter enabled
[ 2.694865] ACPI: (supports S0 S4 S5)
[ 2.694878] ACPI: Using IOAPIC for interrupt routing
[ 2.698748] ACPI: No dock devices found.
[ 2.698841] HEST: Table parsing has been initialized.
[ 2.698844] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 2.699073] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 2.699272] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 2.699274] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 2.699276] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 2.699278] pci_root PNP0A08:00: host bridge window [mem 0xd0000000-0xfdffffff]
[ 2.699280] pci_root PNP0A08:00: host bridge window [mem 0xfed40000-0xfed44fff]
[ 2.699294] pci 0000:00:00.0: [8086:3403] type 0 class 0x000600
[ 2.699341] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[ 2.699361] pci 0000:00:01.0: [8086:3408] type 1 class 0x000604
[ 2.699407] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 2.699426] pci 0000:00:03.0: [8086:340a] type 1 class 0x000604
[ 2.699471] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 2.699493] pci 0000:00:07.0: [8086:340e] type 1 class 0x000604
[ 2.699539] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[ 2.699558] pci 0000:00:09.0: [8086:3410] type 1 class 0x000604
[ 2.699604] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
[ 2.699625] pci 0000:00:14.0: [8086:342e] type 0 class 0x000800
[ 2.699679] pci 0000:00:14.1: [8086:3422] type 0 class 0x000800
[ 2.699733] pci 0000:00:14.2: [8086:3423] type 0 class 0x000800
[ 2.699793] pci 0000:00:1a.0: [8086:2937] type 0 class 0x000c03
[ 2.699830] pci 0000:00:1a.0: reg 20: [io 0xec40-0xec5f]
[ 2.699875] pci 0000:00:1a.1: [8086:2938] type 0 class 0x000c03
[ 2.699911] pci 0000:00:1a.1: reg 20: [io 0xec60-0xec7f]
[ 2.699964] pci 0000:00:1a.7: [8086:293c] type 0 class 0x000c03
[ 2.699982] pci 0000:00:1a.7: reg 10: [mem 0xdf0fe000-0xdf0fe3ff]
[ 2.700061] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 2.700081] pci 0000:00:1c.0: [8086:2940] type 1 class 0x000604
[ 2.700141] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 2.700167] pci 0000:00:1d.0: [8086:2934] type 0 class 0x000c03
[ 2.700203] pci 0000:00:1d.0: reg 20: [io 0xec80-0xec9f]
[ 2.700248] pci 0000:00:1d.1: [8086:2935] type 0 class 0x000c03
[ 2.700285] pci 0000:00:1d.1: reg 20: [io 0xeca0-0xecbf]
[ 2.700338] pci 0000:00:1d.7: [8086:293a] type 0 class 0x000c03
[ 2.700357] pci 0000:00:1d.7: reg 10: [mem 0xdf0ff000-0xdf0ff3ff]
[ 2.700436] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 2.700455] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[ 2.700510] pci 0000:00:1f.0: [8086:2918] type 0 class 0x000601
[ 2.700582] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0c00 (mask 007f)
[ 2.700585] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0ca0 (mask 000f)
[ 2.700588] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 00e0 (mask 000f)
[ 2.700667] pci 0000:01:00.0: [14e4:1639] type 0 class 0x000200
[ 2.700680] pci 0000:01:00.0: reg 10: [mem 0xd6000000-0xd7ffffff 64bit]
[ 2.700754] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 2.700783] pci 0000:01:00.1: [14e4:1639] type 0 class 0x000200
[ 2.700797] pci 0000:01:00.1: reg 10: [mem 0xd8000000-0xd9ffffff 64bit]
[ 2.700871] pci 0000:01:00.1: PME# supported from D0 D3hot D3cold
[ 2.706185] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 2.706192] pci 0000:00:01.0: bridge window [mem 0xd6000000-0xd9ffffff]
[ 2.706253] pci 0000:02:00.0: [14e4:1639] type 0 class 0x000200
[ 2.706267] pci 0000:02:00.0: reg 10: [mem 0xda000000-0xdbffffff 64bit]
[ 2.706341] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 2.706371] pci 0000:02:00.1: [14e4:1639] type 0 class 0x000200
[ 2.706385] pci 0000:02:00.1: reg 10: [mem 0xdc000000-0xddffffff 64bit]
[ 2.706459] pci 0000:02:00.1: PME# supported from D0 D3hot D3cold
[ 2.714162] pci 0000:00:03.0: PCI bridge to [bus 02-02]
[ 2.714168] pci 0000:00:03.0: bridge window [mem 0xda000000-0xddffffff]
[ 2.714211] pci 0000:00:07.0: PCI bridge to [bus 04-04]
[ 2.714251] pci 0000:00:09.0: PCI bridge to [bus 05-05]
[ 2.714305] pci 0000:03:00.0: [1000:0079] type 0 class 0x000104
[ 2.714319] pci 0000:03:00.0: reg 10: [io 0xfc00-0xfcff]
[ 2.714334] pci 0000:03:00.0: reg 14: [mem 0xdf1bc000-0xdf1bffff 64bit]
[ 2.714349] pci 0000:03:00.0: reg 1c: [mem 0xdf1c0000-0xdf1fffff 64bit]
[ 2.714368] pci 0000:03:00.0: reg 30: [mem 0xdf100000-0xdf13ffff pref]
[ 2.714426] pci 0000:03:00.0: supports D1 D2
[ 2.722142] pci 0000:00:1c.0: PCI bridge to [bus 03-03]
[ 2.722147] pci 0000:00:1c.0: bridge window [io 0xf000-0xffff]
[ 2.722152] pci 0000:00:1c.0: bridge window [mem 0xdf100000-0xdf1fffff]
[ 2.722197] pci 0000:06:03.0: [102b:0532] type 0 class 0x000300
[ 2.722216] pci 0000:06:03.0: reg 10: [mem 0xd5800000-0xd5ffffff pref]
[ 2.722225] pci 0000:06:03.0: reg 14: [mem 0xde7fc000-0xde7fffff]
[ 2.722233] pci 0000:06:03.0: reg 18: [mem 0xde800000-0xdeffffff]
[ 2.722262] pci 0000:06:03.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 2.722321] pci 0000:00:1e.0: PCI bridge to [bus 06-06] (subtractive decode)
[ 2.722326] pci 0000:00:1e.0: bridge window [mem 0xde000000-0xdeffffff]
[ 2.722330] pci 0000:00:1e.0: bridge window [mem 0xd5800000-0xd5ffffff 64bit pref]
[ 2.722333] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 2.722335] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 2.722337] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 2.722339] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xfdffffff] (subtractive decode)
[ 2.722341] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[ 2.722361] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 2.722890] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[ 2.722979] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
[ 2.723071] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX7._PRT]
[ 2.723160] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX9._PRT]
[ 2.723249] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SBEX._PRT]
[ 2.723333] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.COMP._PRT]
[ 2.723499] pci0000:00: Requesting ACPI _OSC control (0x15)
[ 2.723743] pci0000:00: ACPI _OSC control (0x15) granted
[ 2.726602] ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 6 7 10 11 14 *15)
[ 2.726664] ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 5 6 7 10 11 *14 15)
[ 2.726725] ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 2.726784] ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 2.726843] ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 2.726904] ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 *6 7 10 11 14 15)
[ 2.726962] ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 2.727022] ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 *14 15)
[ 2.727127] vgaarb: device added: PCI:0000:06:03.0,decodes=io+mem,owns=io+mem,locks=none
[ 2.727129] vgaarb: loaded
[ 2.727130] vgaarb: bridge control possible 0000:06:03.0
[ 2.727166] PCI: Using ACPI for IRQ routing
[ 2.732477] PCI: Discovered peer bus fe
[ 2.732508] pci 0000:fe:00.0: [8086:2c70] type 0 class 0x000600
[ 2.732525] pci 0000:fe:00.1: [8086:2d81] type 0 class 0x000600
[ 2.732542] pci 0000:fe:02.0: [8086:2d90] type 0 class 0x000600
[ 2.732556] pci 0000:fe:02.1: [8086:2d91] type 0 class 0x000600
[ 2.732571] pci 0000:fe:02.2: [8086:2d92] type 0 class 0x000600
[ 2.732587] pci 0000:fe:02.3: [8086:2d93] type 0 class 0x000600
[ 2.732602] pci 0000:fe:02.4: [8086:2d94] type 0 class 0x000600
[ 2.732616] pci 0000:fe:02.5: [8086:2d95] type 0 class 0x000600
[ 2.732632] pci 0000:fe:03.0: [8086:2d98] type 0 class 0x000600
[ 2.732646] pci 0000:fe:03.1: [8086:2d99] type 0 class 0x000600
[ 2.732661] pci 0000:fe:03.2: [8086:2d9a] type 0 class 0x000600
[ 2.732675] pci 0000:fe:03.4: [8086:2d9c] type 0 class 0x000600
[ 2.732691] pci 0000:fe:04.0: [8086:2da0] type 0 class 0x000600
[ 2.732705] pci 0000:fe:04.1: [8086:2da1] type 0 class 0x000600
[ 2.732720] pci 0000:fe:04.2: [8086:2da2] type 0 class 0x000600
[ 2.732735] pci 0000:fe:04.3: [8086:2da3] type 0 class 0x000600
[ 2.732751] pci 0000:fe:05.0: [8086:2da8] type 0 class 0x000600
[ 2.732765] pci 0000:fe:05.1: [8086:2da9] type 0 class 0x000600
[ 2.732780] pci 0000:fe:05.2: [8086:2daa] type 0 class 0x000600
[ 2.732794] pci 0000:fe:05.3: [8086:2dab] type 0 class 0x000600
[ 2.732810] pci 0000:fe:06.0: [8086:2db0] type 0 class 0x000600
[ 2.732825] pci 0000:fe:06.1: [8086:2db1] type 0 class 0x000600
[ 2.732840] pci 0000:fe:06.2: [8086:2db2] type 0 class 0x000600
[ 2.732854] pci 0000:fe:06.3: [8086:2db3] type 0 class 0x000600
[ 2.733385] PCI: Discovered peer bus ff
[ 2.733416] pci 0000:ff:00.0: [8086:2c70] type 0 class 0x000600
[ 2.733433] pci 0000:ff:00.1: [8086:2d81] type 0 class 0x000600
[ 2.733451] pci 0000:ff:02.0: [8086:2d90] type 0 class 0x000600
[ 2.733467] pci 0000:ff:02.1: [8086:2d91] type 0 class 0x000600
[ 2.733484] pci 0000:ff:02.2: [8086:2d92] type 0 class 0x000600
[ 2.733501] pci 0000:ff:02.3: [8086:2d93] type 0 class 0x000600
[ 2.733517] pci 0000:ff:02.4: [8086:2d94] type 0 class 0x000600
[ 2.733534] pci 0000:ff:02.5: [8086:2d95] type 0 class 0x000600
[ 2.733552] pci 0000:ff:03.0: [8086:2d98] type 0 class 0x000600
[ 2.733568] pci 0000:ff:03.1: [8086:2d99] type 0 class 0x000600
[ 2.733585] pci 0000:ff:03.2: [8086:2d9a] type 0 class 0x000600
[ 2.733602] pci 0000:ff:03.4: [8086:2d9c] type 0 class 0x000600
[ 2.733620] pci 0000:ff:04.0: [8086:2da0] type 0 class 0x000600
[ 2.733637] pci 0000:ff:04.1: [8086:2da1] type 0 class 0x000600
[ 2.733654] pci 0000:ff:04.2: [8086:2da2] type 0 class 0x000600
[ 2.733670] pci 0000:ff:04.3: [8086:2da3] type 0 class 0x000600
[ 2.733689] pci 0000:ff:05.0: [8086:2da8] type 0 class 0x000600
[ 2.733705] pci 0000:ff:05.1: [8086:2da9] type 0 class 0x000600
[ 2.733722] pci 0000:ff:05.2: [8086:2daa] type 0 class 0x000600
[ 2.733739] pci 0000:ff:05.3: [8086:2dab] type 0 class 0x000600
[ 2.733758] pci 0000:ff:06.0: [8086:2db0] type 0 class 0x000600
[ 2.733775] pci 0000:ff:06.1: [8086:2db1] type 0 class 0x000600
[ 2.733792] pci 0000:ff:06.2: [8086:2db2] type 0 class 0x000600
[ 2.733809] pci 0000:ff:06.3: [8086:2db3] type 0 class 0x000600
[ 2.734363] PCI: pci_cache_line_size set to 64 bytes
[ 2.734485] reserve RAM buffer: 000000000009e000 - 000000000009ffff
[ 2.734487] reserve RAM buffer: 00000000cf379000 - 00000000cfffffff
[ 2.734593] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 2.734596] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 2.736624] Switching to clocksource hpet
[ 2.738415] pnp: PnP ACPI init
[ 2.738427] ACPI: bus type pnp registered
[ 2.738534] pnp 00:00: [bus 00-ff]
[ 2.738537] pnp 00:00: [io 0x0cf8-0x0cff]
[ 2.738539] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 2.738541] pnp 00:00: [io 0x0d00-0xffff window]
[ 2.738542] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 2.738545] pnp 00:00: [mem 0xd0000000-0xfdffffff window]
[ 2.738546] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 2.738579] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 2.738623] pnp 00:01: [io 0x0080-0x009f]
[ 2.738624] pnp 00:01: [io 0x0000-0x001f]
[ 2.738626] pnp 00:01: [io 0x00c0-0x00df]
[ 2.738628] pnp 00:01: [dma 4]
[ 2.738655] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 2.738676] pnp 00:02: [io 0x00f0-0x00ff]
[ 2.738686] pnp 00:02: [irq 13]
[ 2.738713] pnp 00:02: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 2.738734] pnp 00:03: [io 0x0061]
[ 2.738794] system 00:03: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 2.738816] pnp 00:04: [io 0x0070-0x007f]
[ 2.738823] pnp 00:04: [irq 8]
[ 2.738850] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 2.739016] pnp 00:05: [io 0x03f8-0x03ff]
[ 2.739023] pnp 00:05: [irq 4]
[ 2.739113] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[ 2.739276] pnp 00:06: [io 0x02f8-0x02ff]
[ 2.739283] pnp 00:06: [irq 3]
[ 2.739372] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[ 2.740293] pnp 00:07: [io 0x0800-0x087f]
[ 2.740295] pnp 00:07: [io 0x00e0-0x00e7]
[ 2.740297] pnp 00:07: [io 0x0880-0x08ff]
[ 2.740298] pnp 00:07: [io 0x0900-0x091f]
[ 2.740300] pnp 00:07: [io 0x0920-0x0923]
[ 2.740301] pnp 00:07: [io 0x0924]
[ 2.740303] pnp 00:07: [io 0x0c00-0x0c7f]
[ 2.740304] pnp 00:07: [io 0x0ca0-0x0ca7]
[ 2.740306] pnp 00:07: [io 0x0ca9-0x0cab]
[ 2.740307] pnp 00:07: [io 0x0cad-0x0caf]
[ 2.740309] pnp 00:07: [io 0x0060]
[ 2.740310] pnp 00:07: [io 0x0064]
[ 2.740375] system 00:07: [io 0x0800-0x087f] has been reserved
[ 2.740377] system 00:07: [io 0x0880-0x08ff] has been reserved
[ 2.740379] system 00:07: [io 0x0900-0x091f] has been reserved
[ 2.740382] system 00:07: [io 0x0920-0x0923] has been reserved
[ 2.740384] system 00:07: [io 0x0924] has been reserved
[ 2.740386] system 00:07: [io 0x0c00-0x0c7f] has been reserved
[ 2.740388] system 00:07: [io 0x0ca0-0x0ca7] has been reserved
[ 2.740390] system 00:07: [io 0x0ca9-0x0cab] has been reserved
[ 2.740392] system 00:07: [io 0x0cad-0x0caf] has been reserved
[ 2.740395] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 2.740442] pnp 00:08: [io 0x0ca8]
[ 2.740444] pnp 00:08: [io 0x0cac]
[ 2.740446] pnp 00:08: [irq 0 disabled]
[ 2.740513] system 00:08: [io 0x0ca8] has been reserved
[ 2.740515] system 00:08: [io 0x0cac] has been reserved
[ 2.740518] system 00:08: Plug and Play ACPI device, IDs IPI0001 PNP0c01 (active)
[ 2.741242] pnp 00:09: [mem 0xe0000000-0xefffffff]
[ 2.741306] system 00:09: [mem 0xe0000000-0xefffffff] has been reserved
[ 2.741308] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.741357] pnp 00:0a: [mem 0xfed00000-0xfed003ff]
[ 2.741386] pnp 00:0a: Plug and Play ACPI device, IDs PNP0103 (active)
[ 2.741401] pnp 00:0b: [mem 0xfed90000-0xfed91fff]
[ 2.741464] system 00:0b: [mem 0xfed90000-0xfed91fff] has been reserved
[ 2.741466] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 2.741651] pnp: PnP ACPI: found 12 devices
[ 2.741652] ACPI: ACPI bus type pnp unregistered
[ 2.748735] PCI: max bus depth: 1 pci_try_num: 2
[ 2.748769] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 2.748773] pci 0000:00:01.0: bridge window [mem 0xd6000000-0xd9ffffff]
[ 2.748778] pci 0000:00:03.0: PCI bridge to [bus 02-02]
[ 2.748782] pci 0000:00:03.0: bridge window [mem 0xda000000-0xddffffff]
[ 2.748787] pci 0000:00:07.0: PCI bridge to [bus 04-04]
[ 2.748793] pci 0000:00:09.0: PCI bridge to [bus 05-05]
[ 2.748800] pci 0000:00:1c.0: PCI bridge to [bus 03-03]
[ 2.748803] pci 0000:00:1c.0: bridge window [io 0xf000-0xffff]
[ 2.748807] pci 0000:00:1c.0: bridge window [mem 0xdf100000-0xdf1fffff]
[ 2.748815] pci 0000:06:03.0: BAR 6: assigned [mem 0xde000000-0xde00ffff pref]
[ 2.748817] pci 0000:00:1e.0: PCI bridge to [bus 06-06]
[ 2.748821] pci 0000:00:1e.0: bridge window [mem 0xde000000-0xdeffffff]
[ 2.748824] pci 0000:00:1e.0: bridge window [mem 0xd5800000-0xd5ffffff 64bit pref]
[ 2.748846] pci 0000:00:01.0: setting latency timer to 64
[ 2.748852] pci 0000:00:03.0: setting latency timer to 64
[ 2.748856] pci 0000:00:07.0: setting latency timer to 64
[ 2.748861] pci 0000:00:09.0: setting latency timer to 64
[ 2.748874] pci 0000:00:1c.0: setting latency timer to 64
[ 2.748879] pci 0000:00:1e.0: setting latency timer to 64
[ 2.748882] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 2.748884] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 2.748886] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 2.748887] pci_bus 0000:00: resource 7 [mem 0xd0000000-0xfdffffff]
[ 2.748889] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff]
[ 2.748891] pci_bus 0000:01: resource 1 [mem 0xd6000000-0xd9ffffff]
[ 2.748893] pci_bus 0000:02: resource 1 [mem 0xda000000-0xddffffff]
[ 2.748895] pci_bus 0000:03: resource 0 [io 0xf000-0xffff]
[ 2.748896] pci_bus 0000:03: resource 1 [mem 0xdf100000-0xdf1fffff]
[ 2.748898] pci_bus 0000:06: resource 1 [mem 0xde000000-0xdeffffff]
[ 2.748900] pci_bus 0000:06: resource 2 [mem 0xd5800000-0xd5ffffff 64bit pref]
[ 2.748902] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7]
[ 2.748903] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff]
[ 2.748905] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff]
[ 2.748907] pci_bus 0000:06: resource 7 [mem 0xd0000000-0xfdffffff]
[ 2.748908] pci_bus 0000:06: resource 8 [mem 0xfed40000-0xfed44fff]
[ 2.748910] pci_bus 0000:fe: resource 0 [io 0x0000-0xffff]
[ 2.748912] pci_bus 0000:fe: resource 1 [mem 0x00000000-0xffffffffff]
[ 2.748914] pci_bus 0000:ff: resource 0 [io 0x0000-0xffff]
[ 2.748916] pci_bus 0000:ff: resource 1 [mem 0x00000000-0xffffffffff]
[ 2.749085] NET: Registered protocol family 2
[ 2.749402] IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 2.750532] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 2.751880] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 2.752047] TCP: Hash tables configured (established 524288 bind 65536)
[ 2.752049] TCP reno registered
[ 2.752078] UDP hash table entries: 16384 (order: 7, 524288 bytes)
[ 2.752192] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes)
[ 2.752544] NET: Registered protocol family 1
[ 2.768571] pci 0000:06:03.0: Boot video device
[ 2.768637] PCI: CLS 64 bytes, default 64
[ 2.768685] Unpacking initramfs...
[ 2.952487] Freeing initrd memory: 10688k freed
[ 2.954571] DMAR: Device scope device [0000:00:1a.02] not found
[ 2.954573] DMAR: Device scope device [0000:00:1a.02] not found
[ 2.954575] DMAR: Device scope device [0000:00:1d.02] not found
[ 2.954576] DMAR: Device scope device [0000:00:1d.02] not found
[ 2.954579] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 2.954582] Placing 64MB software IO TLB between ffff8800cb377000 - ffff8800cf377000
[ 2.954584] software IO TLB at phys 0xcb377000 - 0xcf377000
[ 2.956143] audit: initializing netlink socket (disabled)
[ 2.956154] type=2000 audit(1366814282.468:1): initialized
[ 2.968952] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.971958] VFS: Disk quotas dquot_6.5.2
[ 2.972016] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.972120] msgmni has been set to 32768
[ 2.972316] alg: No test for stdrng (krng)
[ 2.972365] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.972368] io scheduler noop registered
[ 2.972369] io scheduler deadline registered
[ 2.972425] io scheduler cfq registered (default)
[ 2.972607] pcieport 0000:00:01.0: setting latency timer to 64
[ 2.972645] pcieport 0000:00:01.0: irq 73 for MSI/MSI-X
[ 2.972695] pcieport 0000:00:03.0: setting latency timer to 64
[ 2.972724] pcieport 0000:00:03.0: irq 74 for MSI/MSI-X
[ 2.972772] pcieport 0000:00:07.0: setting latency timer to 64
[ 2.972802] pcieport 0000:00:07.0: irq 75 for MSI/MSI-X
[ 2.972847] pcieport 0000:00:09.0: setting latency timer to 64
[ 2.972876] pcieport 0000:00:09.0: irq 76 for MSI/MSI-X
[ 2.972924] pcieport 0000:00:1c.0: setting latency timer to 64
[ 2.972958] pcieport 0000:00:1c.0: irq 77 for MSI/MSI-X
[ 2.973045] pcieport 0000:00:01.0: Signaling PME through PCIe PME interrupt
[ 2.973047] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 2.973049] pci 0000:01:00.1: Signaling PME through PCIe PME interrupt
[ 2.973052] pcie_pme 0000:00:01.0:pcie01: service driver pcie_pme loaded
[ 2.973065] pcieport 0000:00:03.0: Signaling PME through PCIe PME interrupt
[ 2.973067] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 2.973069] pci 0000:02:00.1: Signaling PME through PCIe PME interrupt
[ 2.973072] pcie_pme 0000:00:03.0:pcie01: service driver pcie_pme loaded
[ 2.973086] pcieport 0000:00:07.0: Signaling PME through PCIe PME interrupt
[ 2.973089] pcie_pme 0000:00:07.0:pcie01: service driver pcie_pme loaded
[ 2.973102] pcieport 0000:00:09.0: Signaling PME through PCIe PME interrupt
[ 2.973105] pcie_pme 0000:00:09.0:pcie01: service driver pcie_pme loaded
[ 2.973118] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 2.973120] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 2.973123] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 2.973141] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 2.973159] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 2.973160] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 2.973353] intel_idle: MWAIT substates: 0x1120
[ 2.973355] intel_idle: v0.4 model 0x2C
[ 2.973356] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 2.973470] ERST: Error Record Serialization Table (ERST) support is initialized.
[ 2.973662] GHES: APEI firmware first mode is enabled by APEI bit and WHEA _OSC.
[ 2.973732] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 2.994057] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.052088] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.156052] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 3.195809] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 3.215607] Linux agpgart interface v0.103
[ 3.215811] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 3.218689] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 3.218694] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 3.218826] mousedev: PS/2 mouse device common for all mice
[ 3.218867] rtc_cmos 00:04: RTC can wake from S4
[ 3.218969] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 3.218994] rtc0: alarms up to one day, y3k, 242 bytes nvram, hpet irqs
[ 3.219351] cpuidle: using governor ladder
[ 3.219798] cpuidle: using governor menu
[ 3.220029] TCP cubic registered
[ 3.225038] NET: Registered protocol family 10
[ 3.229066] Mobile IPv6
[ 3.229069] NET: Registered protocol family 17
[ 3.229072] Registering the dns_resolver key type
[ 3.229413] PM: Hibernation image not present or could not be loaded.
[ 3.229422] registered taskstats version 1
[ 3.231951] rtc_cmos 00:04: setting system clock to 2013-04-24 14:38:03 UTC (1366814283)
[ 3.231979] Initializing network drop monitor service
[ 3.235590] Freeing unused kernel memory: 576k freed
[ 3.235706] Write protecting the kernel read-only data: 6144k
[ 3.242183] Freeing unused kernel memory: 660k freed
[ 3.247322] Freeing unused kernel memory: 680k freed
[ 3.259386] udevd[148]: starting version 175
[ 3.274970] bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.1.11 (July 20, 2011)
[ 3.275007] bnx2 0000:01:00.0: setting latency timer to 64
[ 3.275760] bnx2 0000:01:00.0: eth0: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem d6000000, IRQ 36, node addr f0:4d:a2:0b:7f:6d
[ 3.275790] bnx2 0000:01:00.1: setting latency timer to 64
[ 3.276374] usbcore: registered new interface driver usbfs
[ 3.276404] usbcore: registered new interface driver hub
[ 3.276439] usbcore: registered new device driver usb
[ 3.276683] bnx2 0000:01:00.1: eth1: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem d8000000, IRQ 48, node addr f0:4d:a2:0b:7f:6f
[ 3.276726] bnx2 0000:02:00.0: setting latency timer to 64
[ 3.276882] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.276917] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 3.276921] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 3.276947] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 3.276975] ehci_hcd 0000:00:1a.7: debug port 1
[ 3.277663] bnx2 0000:02:00.0: eth2: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem da000000, IRQ 32, node addr f0:4d:a2:0b:7f:71
[ 3.277708] bnx2 0000:02:00.1: setting latency timer to 64
[ 3.278530] SCSI subsystem initialized
[ 3.278651] bnx2 0000:02:00.1: eth3: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem dc000000, IRQ 42, node addr f0:4d:a2:0b:7f:73
[ 3.279179] megasas: 00.00.06.12-rc1 Wed. Oct. 5 17:00:00 PDT 2011
[ 3.279198] megasas: 0x1000:0x0079:0x1028:0x1f17: bus 3:slot 0:func 0
[ 3.279213] megaraid_sas 0000:03:00.0: setting latency timer to 64
[ 3.279268] megasas: FW now in Ready state
[ 3.279354] megaraid_sas 0000:03:00.0: irq 78 for MSI/MSI-X
[ 3.280844] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
[ 3.280862] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xdf0fe000
[ 3.295228] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 3.295253] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.295255] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.295257] usb usb1: Product: EHCI Host Controller
[ 3.295259] usb usb1: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[ 3.295260] usb usb1: SerialNumber: 0000:00:1a.7
[ 3.295549] hub 1-0:1.0: USB hub found
[ 3.295554] hub 1-0:1.0: 4 ports detected
[ 3.296570] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.296573] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.296580] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 3.296602] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.300475] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
[ 3.300489] ehci_hcd 0000:00:1d.7: irq 21, io mem 0xdf0ff000
[ 3.303216] megasas_init_mfi: fw_support_ieee=67108864
[ 3.303218] megasas: INIT adapter done
[ 3.315109] uhci_hcd: USB Universal Host Controller Interface driver
[ 3.315114] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 3.315129] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.315132] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.315133] usb usb2: Product: EHCI Host Controller
[ 3.315135] usb usb2: Manufacturer: Linux 3.2.0-4-amd64 ehci_hcd
[ 3.315137] usb usb2: SerialNumber: 0000:00:1d.7
[ 3.315375] hub 2-0:1.0: USB hub found
[ 3.315379] hub 2-0:1.0: 4 ports detected
[ 3.316340] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 3.316343] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 3.316350] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 3.316381] uhci_hcd 0000:00:1a.0: irq 17, io base 0x0000ec40
[ 3.316411] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.316413] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.316414] usb usb3: Product: UHCI Host Controller
[ 3.316416] usb usb3: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 3.316417] usb usb3: SerialNumber: 0000:00:1a.0
[ 3.316615] hub 3-0:1.0: USB hub found
[ 3.316624] hub 3-0:1.0: 2 ports detected
[ 3.316708] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 3.316711] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 3.316716] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 3.316744] uhci_hcd 0000:00:1a.1: irq 18, io base 0x0000ec60
[ 3.316772] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.316775] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.316776] usb usb4: Product: UHCI Host Controller
[ 3.316778] usb usb4: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 3.316779] usb usb4: SerialNumber: 0000:00:1a.1
[ 3.316917] hub 4-0:1.0: USB hub found
[ 3.316923] hub 4-0:1.0: 2 ports detected
[ 3.316998] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 3.317004] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.317009] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 3.317031] uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ec80
[ 3.317060] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.317062] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.317064] usb usb5: Product: UHCI Host Controller
[ 3.317065] usb usb5: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 3.317067] usb usb5: SerialNumber: 0000:00:1d.0
[ 3.317251] hub 5-0:1.0: USB hub found
[ 3.317256] hub 5-0:1.0: 2 ports detected
[ 3.317331] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 3.317333] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.317338] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 3.317366] uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000eca0
[ 3.317390] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.317392] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.317394] usb usb6: Product: UHCI Host Controller
[ 3.317395] usb usb6: Manufacturer: Linux 3.2.0-4-amd64 uhci_hcd
[ 3.317397] usb usb6: SerialNumber: 0000:00:1d.1
[ 3.317569] hub 6-0:1.0: USB hub found
[ 3.317578] hub 6-0:1.0: 2 ports detected
[ 3.375068] scsi0 : LSI SAS based MegaRAID driver
[ 3.378596] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHZ2160B 8A22 PQ: 0 ANSI: 5
[ 3.379532] scsi 0:0:1:0: Direct-Access ATA FUJITSU MHZ2160B 8A22 PQ: 0 ANSI: 5
[ 3.481719] scsi 0:0:32:0: Enclosure DP BACKPLANE 1.07 PQ: 0 ANSI: 5
[ 3.496974] scsi 0:2:0:0: Direct-Access DELL PERC H700 2.10 PQ: 0 ANSI: 5
[ 3.520162] sd 0:2:0:0: [sda] 311427072 512-byte logical blocks: (159 GB/148 GiB)
[ 3.520284] sd 0:2:0:0: [sda] Write Protect is off
[ 3.520288] sd 0:2:0:0: [sda] Mode Sense: 1f 00 00 08
[ 3.520402] sd 0:2:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.521140] sda: sda1
[ 3.522274] sd 0:2:0:0: [sda] Attached SCSI disk
[ 3.610437] usb 1-3: new high-speed USB device number 2 using ehci_hcd
[ 3.631898] ses 0:0:32:0: Attached Enclosure device
[ 3.632078] ses 0:0:32:0: Attached scsi generic sg0 type 13
[ 3.632157] sd 0:2:0:0: Attached scsi generic sg1 type 0
[ 3.742398] usb 1-3: New USB device found, idVendor=0424, idProduct=2514
[ 3.742403] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.742689] hub 1-3:1.0: USB hub found
[ 3.742750] hub 1-3:1.0: 3 ports detected
[ 3.949538] Refined TSC clocksource calibration: 2659.999 MHz.
[ 3.949544] Switching to clocksource tsc
[ 3.968073] device-mapper: uevent: version 1.0.3
[ 3.969404] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 4.097157] usb 5-2: new full-speed USB device number 2 using uhci_hcd
[ 4.259754] usb 5-2: New USB device found, idVendor=0624, idProduct=0248
[ 4.259759] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4.259762] usb 5-2: Product: USB Composite Device-0
[ 4.259765] usb 5-2: Manufacturer: Avocent
[ 4.259767] usb 5-2: SerialNumber: 20120430
[ 4.294811] input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.0/input/input0
[ 4.294925] generic-usb 0003:0624:0248.0001: input,hidraw0: USB HID v1.00 Keyboard [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input0
[ 4.298773] input: Avocent USB Composite Device-0 as /devices/pci0000:00/0000:00:1d.0/usb5/5-2/5-2:1.1/input/input1
[ 4.299025] generic-usb 0003:0624:0248.0002: input,hidraw1: USB HID v1.00 Mouse [Avocent USB Composite Device-0] on usb-0000:00:1d.0-2/input1
[ 4.299045] usbcore: registered new interface driver usbhid
[ 4.299047] usbhid: USB HID core driver
[ 4.554569] PM: Starting manual resume from disk
[ 4.554571] PM: Hibernation image partition 254:1 present
[ 4.554573] PM: Looking for hibernation image.
[ 4.554855] PM: Image not found (code -22)
[ 4.554859] PM: Hibernation image not present or could not be loaded.
[ 4.623632] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 5.757425] udevd[537]: starting version 175
[ 6.051196] wmi: Mapper loaded
[ 6.066963] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 6.066967] ACPI: Power Button [PWRF]
[ 6.124002] ACPI Error: No handler for Region [IPMI] (ffff88032345f300) [IPMI] (20110623/evregion-373)
[ 6.124007] ACPI Error: Region IPMI (ID=7) has no handler (20110623/exfldio-292)
[ 6.124012] ACPI Error: Method parse/execution failed [\_SB_.PMI0._GHL] (Node ffff880622c6eab0), AE_NOT_EXIST (20110623/psparse-536)
[ 6.124028] ACPI Error: Method parse/execution failed [\_SB_.PMI0._PMC] (Node ffff880622c6eb00), AE_NOT_EXIST (20110623/psparse-536)
[ 6.124038] ACPI Exception: AE_NOT_EXIST, Evaluating _PMC (20110623/power_meter-773)
[ 6.130790] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 6.171267] EDAC MC: Ver: 2.1.0
[ 6.180112] EDAC MC1: Giving out device to 'i7core_edac.c' 'i7 core #1': DEV 0000:fe:03.0
[ 6.180125] EDAC PCI0: Giving out device to module 'i7core_edac' controller 'EDAC PCI controller': DEV '0000:fe:03.0' (POLLED)
[ 6.180540] EDAC MC0: Giving out device to 'i7core_edac.c' 'i7 core #0': DEV 0000:ff:03.0
[ 6.180551] EDAC PCI1: Giving out device to module 'i7core_edac' controller 'EDAC PCI controller': DEV '0000:ff:03.0' (POLLED)
[ 6.181589] EDAC i7core: Driver loaded, 2 memory controller(s) found.
[ 6.183618] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 6.211381] Error: Driver 'pcspkr' is already registered, aborting...
[ 6.231462] iTCO_vendor_support: vendor-support=0
[ 6.247618] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 6.247686] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0x0860)
[ 6.247754] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 6.309550] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[ 7.420577] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 7.537617] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 7.679914] loop: module loaded
[ 7.913891] Adding 140087292k swap on /dev/mapper/voip12-swap_1. Priority:-1 extents:1 across:140087292k
[ 9.991871] RPC: Registered named UNIX socket transport module.
[ 9.991873] RPC: Registered udp transport module.
[ 9.991874] RPC: Registered tcp transport module.
[ 9.991876] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 10.026318] FS-Cache: Loaded
[ 10.075227] FS-Cache: Netfs 'nfs' registered for caching
[ 10.094299] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 10.485135] bnx2 0000:01:00.0: firmware: agent loaded bnx2/bnx2-mips-09-6.2.1a.fw into memory
[ 10.505994] bnx2 0000:01:00.0: firmware: agent loaded bnx2/bnx2-rv2p-09-6.0.17.fw into memory
[ 10.506812] bnx2 0000:01:00.0: irq 79 for MSI/MSI-X
[ 10.506822] bnx2 0000:01:00.0: irq 80 for MSI/MSI-X
[ 10.506830] bnx2 0000:01:00.0: irq 81 for MSI/MSI-X
[ 10.506837] bnx2 0000:01:00.0: irq 82 for MSI/MSI-X
[ 10.506844] bnx2 0000:01:00.0: irq 83 for MSI/MSI-X
[ 10.506851] bnx2 0000:01:00.0: irq 84 for MSI/MSI-X
[ 10.506858] bnx2 0000:01:00.0: irq 85 for MSI/MSI-X
[ 10.506865] bnx2 0000:01:00.0: irq 86 for MSI/MSI-X
[ 10.506872] bnx2 0000:01:00.0: irq 87 for MSI/MSI-X
[ 10.570553] bnx2 0000:01:00.0: eth0: using MSIX
[ 10.571555] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.663017] bnx2 0000:01:00.0: eth0: NIC Copper Link is Up, 1000 Mbps full duplex
[ 13.664070] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 269.207828] Bridge firewalling registered
[ 269.235914] 8021q: 802.1Q VLAN Support v1.8
[ 276.145086] ipmi message handler version 39.2
[ 276.155279] IPMI System Interface driver.
[ 276.155335] ipmi_si: probing via SMBIOS
[ 276.155337] ipmi_si: SMBIOS: io 0xca8 regsize 1 spacing 4 irq 0
[ 276.155339] ipmi_si: Adding SMBIOS-specified kcs state machine
[ 276.155341] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca8, slave address 0x20, irq 0
[ 276.325184] ipmi_si ipmi_si.0: Found new BMC (man_id: 0x0002a2, prod_id: 0x0100, dev_id: 0x20)
[ 276.325196] ipmi_si ipmi_si.0: IPMI kcs interface initialized
[ 276.536534] ipmi device interface
[ 3270.432590] bnx2 0000:01:00.0: irq 79 for MSI/MSI-X
[ 3270.432598] bnx2 0000:01:00.0: irq 80 for MSI/MSI-X
[ 3270.432606] bnx2 0000:01:00.0: irq 81 for MSI/MSI-X
[ 3270.432613] bnx2 0000:01:00.0: irq 82 for MSI/MSI-X
[ 3270.432620] bnx2 0000:01:00.0: irq 83 for MSI/MSI-X
[ 3270.432627] bnx2 0000:01:00.0: irq 84 for MSI/MSI-X
[ 3270.432635] bnx2 0000:01:00.0: irq 85 for MSI/MSI-X
[ 3270.432642] bnx2 0000:01:00.0: irq 86 for MSI/MSI-X
[ 3270.432649] bnx2 0000:01:00.0: irq 87 for MSI/MSI-X
[ 3270.492905] bnx2 0000:01:00.0: eth0: using MSIX
[ 3270.493978] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3273.626726] bnx2 0000:01:00.0: eth0: NIC Copper Link is Up, 1000 Mbps full duplex
[ 3273.627909] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3360.400392] bnx2 0000:01:00.0: irq 79 for MSI/MSI-X
[ 3360.400401] bnx2 0000:01:00.0: irq 80 for MSI/MSI-X
[ 3360.400408] bnx2 0000:01:00.0: irq 81 for MSI/MSI-X
[ 3360.400416] bnx2 0000:01:00.0: irq 82 for MSI/MSI-X
[ 3360.400423] bnx2 0000:01:00.0: irq 83 for MSI/MSI-X
[ 3360.400431] bnx2 0000:01:00.0: irq 84 for MSI/MSI-X
[ 3360.400438] bnx2 0000:01:00.0: irq 85 for MSI/MSI-X
[ 3360.400446] bnx2 0000:01:00.0: irq 86 for MSI/MSI-X
[ 3360.400453] bnx2 0000:01:00.0: irq 87 for MSI/MSI-X
[ 3360.460789] bnx2 0000:01:00.0: eth0: using MSIX
[ 3360.461765] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3362.931362] bnx2 0000:01:00.0: eth0: NIC Copper Link is Up, 1000 Mbps full duplex
[ 3362.932417] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3397.659527] bnx2 0000:01:00.0: irq 79 for MSI/MSI-X
[ 3397.659535] bnx2 0000:01:00.0: irq 80 for MSI/MSI-X
[ 3397.659543] bnx2 0000:01:00.0: irq 81 for MSI/MSI-X
[ 3397.659550] bnx2 0000:01:00.0: irq 82 for MSI/MSI-X
[ 3397.659557] bnx2 0000:01:00.0: irq 83 for MSI/MSI-X
[ 3397.659565] bnx2 0000:01:00.0: irq 84 for MSI/MSI-X
[ 3397.659572] bnx2 0000:01:00.0: irq 85 for MSI/MSI-X
[ 3397.659580] bnx2 0000:01:00.0: irq 86 for MSI/MSI-X
[ 3397.659587] bnx2 0000:01:00.0: irq 87 for MSI/MSI-X
[ 3397.719979] bnx2 0000:01:00.0: eth0: using MSIX
[ 3397.720985] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3400.106812] bnx2 0000:01:00.0: eth0: NIC Copper Link is Up, 1000 Mbps full duplex
[ 3400.107874] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3418.878675] bnx2 0000:01:00.0: irq 79 for MSI/MSI-X
[ 3418.878683] bnx2 0000:01:00.0: irq 80 for MSI/MSI-X
[ 3418.878692] bnx2 0000:01:00.0: irq 81 for MSI/MSI-X
[ 3418.878700] bnx2 0000:01:00.0: irq 82 for MSI/MSI-X
[ 3418.878707] bnx2 0000:01:00.0: irq 83 for MSI/MSI-X
[ 3418.878714] bnx2 0000:01:00.0: irq 84 for MSI/MSI-X
[ 3418.878721] bnx2 0000:01:00.0: irq 85 for MSI/MSI-X
[ 3418.878729] bnx2 0000:01:00.0: irq 86 for MSI/MSI-X
[ 3418.878736] bnx2 0000:01:00.0: irq 87 for MSI/MSI-X
[ 3418.955021] bnx2 0000:01:00.0: eth0: using MSIX
[ 3418.956023] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3421.814530] bnx2 0000:01:00.0: eth0: NIC Copper Link is Up, 1000 Mbps full duplex
[ 3421.815603] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 4515.077372] device eth0 entered promiscuous mode
[ 4836.420343] device eth0 left promiscuous mode
[42995.606407] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[42995.606409] EDD information not available.
[42996.856083] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[42996.856086] EDD information not available.
** Model information
sys_vendor: Dell Inc.
product_name: PowerEdge R610
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: 6.3.0
board_vendor: Dell Inc.
board_name: 0F0XJ6
board_version: A06
** Loaded modules:
ipmi_devintf
ipmi_si
ipmi_msghandler
8021q
garp
bridge
stp
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
loop
coretemp
crc32c_intel
ghash_clmulni_intel
aesni_intel
iTCO_wdt
iTCO_vendor_support
snd_pcm
snd_page_alloc
dcdbas
i7core_edac
psmouse
edac_core
snd_timer
snd
soundcore
serio_raw
pcspkr
joydev
evdev
acpi_power_meter
aes_x86_64
processor
button
wmi
aes_generic
cryptd
thermal_sys
ext4
crc16
jbd2
mbcache
usbhid
hid
dm_mod
sg
ses
enclosure
sd_mod
crc_t10dif
uhci_hcd
megaraid_sas
scsi_mod
ehci_hcd
usbcore
usb_common
bnx2
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5500 I/O Hub to ESI Port [8086:3403] (rev 13)
Subsystem: Dell PowerEdge R610 I/O Hub to ESI Port [1028:0236]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 15
Capabilities: [60] MSI: Enable- Count=1/2 Maskable+ 64bit-
Address: 00000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 17s to 64s, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [160 v0] Vendor Specific Information: ID=0002 Rev=0 Len=00c <?>
00:01.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 [8086:3408] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d6000000-d9ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Dell Device [1028:0236]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00358 Data: 0000
Masking: 00000002 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 1s to 3.5s, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [160 v0] Vendor Specific Information: ID=0002 Rev=0 Len=00c <?>
Kernel driver in use: pcieport
00:03.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 [8086:340a] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: da000000-ddffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Dell Device [1028:0236]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00378 Data: 0000
Masking: 00000002 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 1s to 3.5s, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [160 v0] Vendor Specific Information: ID=0002 Rev=0 Len=00c <?>
Kernel driver in use: pcieport
00:07.0 PCI bridge [0604]: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 [8086:340e] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Dell Device [1028:0236]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee00398 Data: 0000
Masking: 00000002 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #7, Speed 5GT/s, Width x8, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 1s to 3.5s, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Capabilities: [160 v0] Vendor Specific Information: ID=0002 Rev=0 Len=00c <?>
Kernel driver in use: pcieport
00:09.0 PCI bridge [0604]: Intel Corporation 7500/5520/5500/X58 I/O Hub PCI Express Root Port 9 [8086:3410] (rev 13) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: Dell Device [1028:0236]
Capabilities: [60] MSI: Enable+ Count=1/2 Maskable+ 64bit-
Address: fee003b8 Data: 0000
Masking: 00000002 Pending: 00000000
Capabilities: [90] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #9, Speed 5GT/s, Width x8, ASPM L0s L1, Latency L0 <512ns, L1 <64us
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #2, PowerLimit 25.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd Off, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BCD, TimeoutDis+ ARIFwd+
DevCtl2: Completion Timeout: 1s to 3.5s, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [e0] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol+
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [150 v1] Access Control Services
ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
ACSCtl: SrcValid- TransBlk- ReqRedir- CmpltRedir- UpstreamFwd- EgressCtrl- DirectTrans-
Kernel driver in use: pcieport
00:14.0 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub System Management Registers [8086:342e] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Kernel driver in use: i7core_edac
00:14.1 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers [8086:3422] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
00:14.2 PIC [0800]: Intel Corporation 7500/5520/5500/X58 I/O Hub Control Status and RAS Registers [8086:3423] (rev 13) (prog-if 00 [8259])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM L0s, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise+ LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
00:1a.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell PowerEdge R610 USB UHCI Controller [1028:0236]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at ec40 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell PowerEdge R610 USB UHCI Controller [1028:0236]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at ec60 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell PowerEdge R610 USB EHCI Controller [1028:0236]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 0: Memory at df0fe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-0000ffff
Memory behind bridge: df100000-df1fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal+ ErrFatal+ PMEIntEna+ CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee003d8 Data: 0000
Capabilities: [90] Subsystem: Dell Device [1028:0236]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000feda8000
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell PowerEdge R610 USB UHCI Controller [1028:0236]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at ec80 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell PowerEdge R610 USB UHCI Controller [1028:0236]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at eca0 [size=32]
Capabilities: [50] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell PowerEdge R610 USB EHCI Controller [1028:0236]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at df0ff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
Memory behind bridge: de000000-deffffff
Prefetchable memory behind bridge: 00000000d5800000-00000000d5ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Dell Device [1028:0236]
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IB (ICH9) LPC Interface Controller [8086:2918] (rev 02)
Subsystem: Dell PowerEdge R610 82801IB (ICH9) LPC Interface Controller [1028:0236]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
01:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5709 Gigabit Ethernet [14e4:1639] (rev 20)
Subsystem: Dell PowerEdge R610 BCM5709 Gigabit Ethernet [1028:0236]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 36
Region 0: Memory at d6000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme II Ethernet Controller
Read-only fields:
[PN] Part number: BCM95709C0
[EC] Engineering changes: 220197-2
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 30 32 38
[V0] Vendor specific: 7.4.8
[RV] Reserved: checksum good, 23 byte(s) reserved
End
Capabilities: [58] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable+ Count=9 Masked-
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <2us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Device Serial Number f0-4d-a2-ff-fe-0b-7f-6d
Capabilities: [110 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Power Budgeting <?>
Capabilities: [160 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: bnx2
01:00.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5709 Gigabit Ethernet [14e4:1639] (rev 20)
Subsystem: Dell PowerEdge R610 BCM5709 Gigabit Ethernet [1028:0236]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 48
Region 0: Memory at d8000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme II Ethernet Controller
Read-only fields:
[PN] Part number: BCM95709C0
[EC] Engineering changes: 220197-2
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 30 32 38
[V0] Vendor specific: 7.4.8
[RV] Reserved: checksum good, 23 byte(s) reserved
End
Capabilities: [58] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable- Count=9 Masked-
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <2us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Device Serial Number f0-4d-a2-ff-fe-0b-7f-6f
Capabilities: [110 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Power Budgeting <?>
Capabilities: [160 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: bnx2
02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5709 Gigabit Ethernet [14e4:1639] (rev 20)
Subsystem: Dell PowerEdge R610 BCM5709 Gigabit Ethernet [1028:0236]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: Memory at da000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme II Ethernet Controller
Read-only fields:
[PN] Part number: BCM95709C0
[EC] Engineering changes: 220197-2
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 30 32 38
[V0] Vendor specific: 7.4.8
[RV] Reserved: checksum good, 23 byte(s) reserved
End
Capabilities: [58] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable- Count=9 Masked-
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <2us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Device Serial Number f0-4d-a2-ff-fe-0b-7f-71
Capabilities: [110 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Power Budgeting <?>
Capabilities: [160 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: bnx2
02:00.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme II BCM5709 Gigabit Ethernet [14e4:1639] (rev 20)
Subsystem: Dell PowerEdge R610 BCM5709 Gigabit Ethernet [1028:0236]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 42
Region 0: Memory at dc000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Broadcom NetXtreme II Ethernet Controller
Read-only fields:
[PN] Part number: BCM95709C0
[EC] Engineering changes: 220197-2
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 30 32 38
[V0] Vendor specific: 7.4.8
[RV] Reserved: checksum good, 23 byte(s) reserved
End
Capabilities: [58] MSI: Enable- Count=1/16 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable- Count=9 Masked-
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
MaxPayload 256 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <2us, L1 <2us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Device Serial Number f0-4d-a2-ff-fe-0b-7f-73
Capabilities: [110 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [150 v1] Power Budgeting <?>
Capabilities: [160 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: bnx2
03:00.0 RAID bus controller [0104]: LSI Logic / Symbios Logic MegaRAID SAS 2108 [Liberator] [1000:0079] (rev 05)
Subsystem: Dell PERC H700 Integrated [1028:1f17]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at fc00 [size=256]
Region 1: Memory at df1bc000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at df1c0000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at df100000 [disabled] [size=256K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range BC, TimeoutDis+
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [d0] Vital Product Data
Unknown small resource type 00, will not decode more.
Capabilities: [a8] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c0] MSI-X: Enable+ Count=15 Masked-
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003800
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt+ RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP+ FCP+ CmpltTO+ CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC+ UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [138 v1] Power Budgeting <?>
Kernel driver in use: megaraid_sas
06:03.0 VGA compatible controller [0300]: Matrox Electronics Systems Ltd. MGA G200eW WPCM450 [102b:0532] (rev 0a) (prog-if 00 [VGA controller])
Subsystem: Dell PowerEdge R610 MGA G200eW WPCM450 [1028:0236]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 8000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d5800000 (32-bit, prefetchable) [size=8M]
Region 1: Memory at de7fc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at de800000 (32-bit, non-prefetchable) [size=8M]
[virtual] Expansion ROM at de000000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
fe:00.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath Architecture Generic Non-core Registers [8086:2c70] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:00.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath Architecture System Address Decoder [8086:2d81] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:02.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 0 [8086:2d90] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:02.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 0 [8086:2d91] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:02.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link 0 [8086:2d92] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:02.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link 1 [8086:2d93] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:02.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 1 [8086:2d94] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:02.5 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 1 [8086:2d95] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:03.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Registers [8086:2d98] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:03.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Target Address Decoder [8086:2d99] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:03.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller RAS Registers [8086:2d9a] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:03.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Test Registers [8086:2d9c] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:04.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Control [8086:2da0] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:04.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Address [8086:2da1] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:04.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Rank [8086:2da2] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:04.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Thermal Control [8086:2da3] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:05.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Control [8086:2da8] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:05.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Address [8086:2da9] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:05.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Rank [8086:2daa] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:05.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Thermal Control [8086:2dab] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:06.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Control [8086:2db0] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:06.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Address [8086:2db1] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:06.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Rank [8086:2db2] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
fe:06.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Thermal Control [8086:2db3] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:00.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath Architecture Generic Non-core Registers [8086:2c70] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:00.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QuickPath Architecture System Address Decoder [8086:2d81] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 0 [8086:2d90] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 0 [8086:2d91] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link 0 [8086:2d92] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Mirror Port Link 1 [8086:2d93] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Link 1 [8086:2d94] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.5 Host bridge [0600]: Intel Corporation Xeon 5600 Series QPI Physical 1 [8086:2d95] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Registers [8086:2d98] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Target Address Decoder [8086:2d99] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller RAS Registers [8086:2d9a] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:03.4 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Test Registers [8086:2d9c] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Control [8086:2da0] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Address [8086:2da1] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Rank [8086:2da2] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:04.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 0 Thermal Control [8086:2da3] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Control [8086:2da8] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Address [8086:2da9] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Rank [8086:2daa] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:05.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 1 Thermal Control [8086:2dab] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.0 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Control [8086:2db0] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.1 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Address [8086:2db1] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.2 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Rank [8086:2db2] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:06.3 Host bridge [0600]: Intel Corporation Xeon 5600 Series Integrated Memory Controller Channel 2 Thermal Control [8086:2db3] (rev 02)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 005 Device 002: ID 0624:0248 Avocent Corp.
-- System Information:
Debian Release: 7.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-4-amd64 (SMP w/24 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.2.0-4-amd64 recommends:
pn firmware-linux-free <none>
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
ii firmware-bnx2 0.36+wheezy.1
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
Reply to: