Bug#702368: atl1c: freezes on ifconfig eth0 down/up when no cable is connected
Package: src:linux
Version: 3.2.39-2
Severity: normal
Dear Maintainer,
I've discovered a problem with the atl1c module which is responsible
for the ethernet controller on my laptop. A few simple steps to reproduce the bug:
1) Turn on the machine without any ethernet cable connected;
2) Run the following commands (as root):
root@georgios:/home/yurb# time ifconfig eth0 down
real 0m12.015s
user 0m0.072s
sys 0m0.728s
root@georgios:/home/yurb# time ifconfig eth0 up
real 0m17.182s
user 0m0.000s
sys 0m0.024s
During the delays after running the commands the machine stays
unresponsible. The delays can be big. Sometimes it's only a few
seconds and sometimes it's up to 17s as in this case.
I've initially spotted this behavior with wicd: each time I connected
to a wifi network the system was freezing. But if I rmmod atl1c no
freezes would occour.
The problem seems to be fixed in linux 3.7.8 wich I've installed from
debian experimental.
I've also seen this problem on another machine from different
manufacturer (can't access it now), so it seem not that rare.
How can I help backport the fix to the 3.2 kernel to eliminate the
problem in wheezy?
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-15) ) #1 SMP Debian 3.2.39-2
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=28157690-0ed4-4b55-bbea-31fdbaffbc6f ro quiet
** Tainted: WO (4608)
* Taint on warning.
* Out-of-tree module has been loaded.
** Kernel log:
[ 7.192667] acer_wmi: Brightness must be controlled by generic video driver
[ 7.193726] input: Acer WMI hotkeys as /devices/virtual/input/input6
[ 7.216123] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 7.217702] Registered led device: ath9k-phy0
[ 7.217729] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc90010920000, irq=17
[ 7.233031] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[ 7.233050] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 7.233057] [drm] Driver supports precise vblank timestamp query.
[ 7.233202] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 7.264540] fixme: max PWM is zero.
[ 7.396946] usb 1-4: New USB device found, idVendor=04f2, idProduct=b209
[ 7.396970] usb 1-4: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[ 7.396976] usb 1-4: Product: WebCam
[ 7.396981] usb 1-4: Manufacturer: Chicony Electronics Co., Ltd.
[ 7.542895] [drm] initialized overlay support
[ 7.563826] fbcon: inteldrmfb (fb0) is primary device
[ 7.841805] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000
[ 7.899102] Linux media interface: v0.10
[ 7.911742] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[ 7.972898] Linux video capture interface: v2.00
[ 7.998490] uvcvideo: Found UVC 1.00 device WebCam (04f2:b209)
[ 8.001819] input: WebCam as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/input/input8
[ 8.002243] usbcore: registered new interface driver uvcvideo
[ 8.002253] USB Video Class driver (1.1.1)
[ 8.036785] Console: switching to colour frame buffer device 128x37
[ 8.043738] fb0: inteldrmfb frame buffer device
[ 8.043743] drm: registered panic notifier
[ 8.368329] acpi device:27: registered as cooling_device5
[ 8.369361] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input9
[ 8.369744] ACPI: Video Device [OVGA] (multi-head: yes rom: no post: no)
[ 8.369845] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 8.370214] snd_hda_intel 0000:00:1b.0: irq 44 for MSI/MSI-X
[ 8.370337] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 9.462694] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
[ 9.467153] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[ 9.467708] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 10.846495] Adding 923732k swap on /dev/sda2. Priority:-1 extents:1 across:923732k
[ 11.537604] loop: module loaded
[ 13.531046] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 14.788612] atl1c 0000:01:00.0: irq 45 for MSI/MSI-X
[ 14.876430] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 15.113135] RPC: Registered named UNIX socket transport module.
[ 15.113145] RPC: Registered udp transport module.
[ 15.113150] RPC: Registered tcp transport module.
[ 15.113155] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 15.191565] FS-Cache: Loaded
[ 15.253904] FS-Cache: Netfs 'nfs' registered for caching
[ 15.275485] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 17.603766] vboxdrv: Found 4 processor cores.
[ 17.604678] vboxdrv: fAsync=0 offMin=0x640 offMax=0x5d02
[ 17.604863] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 17.604869] vboxdrv: Successfully loaded version 4.1.18_Debian (interface 0x00190000).
[ 18.745918] vboxpci: IOMMU not found (not registered)
[ 25.123126] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 67.503009] sched: RT throttling activated
[ 75.684915] atl1c 0000:01:00.0: irq 45 for MSI/MSI-X
[ 75.705908] ------------[ cut here ]------------
[ 75.705908] WARNING: at /build/buildd-linux_3.2.39-2-amd64-G5_nN0/linux-3.2.39/kernel/watchdog.c:241 watchdog_overflow_callback+0x93/0x9e()
[ 75.705908] Hardware name: eM355
[ 75.705908] Watchdog detected hard LOCKUP on cpu 0
[ 75.705908] Modules linked in: pci_stub vboxpci(O) vboxnetadp(O) vboxnetflt(O) vboxdrv(O) nfsd nfs nfs_acl auth_rpcgss fscache lockd sunrpc ext4 crc16 jbd2 loop snd_hda_codec_realtek uvcvideo videodev joydev v4l2_compat_ioctl32 media snd_hda_intel snd_hda_codec snd_hwdep snd_pcm arc4 acer_wmi i915 snd_page_alloc ath9k ath9k_common ath9k_hw uhci_hcd ath snd_seq snd_seq_device snd_timer drm_kms_helper mac80211 snd i2c_i801 iTCO_wdt ehci_hcd psmouse sparse_keymap drm i2c_algo_bit cfg80211 rfkill usbcore soundcore atl1c i2c_core iTCO_vendor_support serio_raw usb_common coretemp evdev pcspkr battery ac power_supply acpi_cpufreq mperf processor video button wmi ext2 mbcache sd_mod crc_t10dif ahci libahci libata scsi_mod thermal fan thermal_sys
[ 75.705908] Pid: 2887, comm: lxterminal Tainted: G O 3.2.0-4-amd64 #1 Debian 3.2.39-2
[ 75.705908] Call Trace:
[ 75.705908] <NMI> [<ffffffff81046a35>] ? warn_slowpath_common+0x78/0x8c
[ 86.386585] [<ffffffff81046ae1>] ? warn_slowpath_fmt+0x45/0x4a
[ 86.386585] [<ffffffff81013a24>] ? sched_clock+0x5/0x8
[ 86.386585] [<ffffffff8109028c>] ? watchdog_overflow_callback+0x93/0x9e
[ 86.386585] [<ffffffff810901f9>] ? touch_nmi_watchdog+0x60/0x60
[ 86.386585] [<ffffffff810aff4f>] ? __perf_event_overflow+0xf9/0x17b
[ 86.386585] [<ffffffff81063c22>] ? local_clock+0x24/0x2b
[ 86.386585] [<ffffffff810ae36d>] ? perf_event_update_userpage+0x9/0x9a
[ 86.386585] [<ffffffff81019f23>] ? x86_perf_event_set_period+0x101/0x10b
[ 86.386585] [<ffffffff8101d2ce>] ? intel_pmu_handle_irq+0x206/0x267
[ 86.386585] [<ffffffff8134e8d9>] ? nmi_handle.isra.0+0x3e/0x61
[ 86.386585] [<ffffffff8134e979>] ? do_nmi+0x7d/0x258
[ 86.386585] [<ffffffff8134e1f0>] ? nmi+0x20/0x30
[ 86.386585] [<ffffffff81029ae0>] ? read_hpet+0xd/0x10
[ 86.386585] <<EOE>> <IRQ> [<ffffffff81065ead>] ? timekeeping_get_ns+0xd/0x2a
[ 86.386585] [<ffffffff81066f36>] ? ktime_get_update_offsets+0x32/0x84
[ 86.386585] [<ffffffff8106283a>] ? hrtimer_interrupt+0x5e/0x1af
[ 86.386585] [<ffffffff8104b4c8>] ? __local_bh_enable+0x40/0x77
[ 86.386585] [<ffffffff81354bac>] ? call_softirq+0x1c/0x30
[ 86.386585] [<ffffffff810241db>] ? smp_apic_timer_interrupt+0x6f/0x82
[ 86.386585] [<ffffffff8135341e>] ? apic_timer_interrupt+0x6e/0x80
[ 86.386585] <EOI>
[ 86.386585] ---[ end trace bee87788246ef525 ]---
[ 86.983811] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 93.510683] atl1c 0000:01:00.0: irq 45 for MSI/MSI-X
[ 93.595708] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 95.934766] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 95.935887] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 97.258730] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Down
[ 99.085234] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 106.672042] eth0: no IPv6 routers present
[ 133.589649] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 133.960260] atl1c 0000:01:00.0: irq 45 for MSI/MSI-X
[ 133.960551] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 134.282013] atl1c 0000:01:00.0: irq 45 for MSI/MSI-X
[ 134.282307] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[ 144.520094] eth0: no IPv6 routers present
** Model information
sys_vendor: eMachines
product_name: eM355
product_version: V3.16(DDR3)
chassis_vendor: eMachines
chassis_version: V3.16(DDR3)
bios_vendor: eMachines
bios_version: V3.16(DDR3)
board_vendor: eMachines
board_name: HM02_PT
board_version: V3.16(DDR3)
** Loaded modules:
pci_stub
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
ext4
crc16
jbd2
loop
snd_hda_codec_realtek
uvcvideo
videodev
joydev
v4l2_compat_ioctl32
media
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
arc4
acer_wmi
i915
snd_page_alloc
ath9k
ath9k_common
ath9k_hw
uhci_hcd
ath
snd_seq
snd_seq_device
snd_timer
drm_kms_helper
mac80211
snd
i2c_i801
iTCO_wdt
ehci_hcd
psmouse
sparse_keymap
drm
i2c_algo_bit
cfg80211
rfkill
usbcore
soundcore
atl1c
i2c_core
iTCO_vendor_support
serio_raw
usb_common
coretemp
evdev
pcspkr
battery
ac
power_supply
acpi_cpufreq
mperf
processor
video
button
wmi
ext2
mbcache
sd_mod
crc_t10dif
ahci
libahci
libata
scsi_mod
thermal
fan
thermal_sys
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge [8086:a010] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort+ <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a011] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at 98180000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 60c0 [size=8]
Region 2: Memory at 80000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at 98000000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller [8086:a012] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at 98100000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at 98200000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: 97000000-97ffffff
Prefetchable memory behind bridge: 0000000090000000-0000000090ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: 96000000-96ffffff
Prefetchable memory behind bridge: 0000000091000000-0000000091ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 4: I/O ports at 6080 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 6060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 6040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 22
Region 4: I/O ports at 6020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 22
Region 0: Memory at 98204400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 42
Region 0: I/O ports at 60b8 [size=8]
Region 1: I/O ports at 60cc [size=4]
Region 2: I/O ports at 60b0 [size=8]
Region 3: I/O ports at 60c8 [size=4]
Region 4: I/O ports at 60a0 [size=16]
Region 5: Memory at 98204000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02)
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 6000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet [1969:2060] (rev c1)
Subsystem: Acer Incorporated [ALI] Device [1025:0349]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at 97000000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 5000 [size=128]
Capabilities: <access denied>
Kernel driver in use: atl1c
02:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
Subsystem: Foxconn International, Inc. Device [105b:e016]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 96000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 04f2:b209 Chicony Electronics Co., Ltd
-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.2.0-4-amd64 (SMP w/4 CPU cores)
Locale: LANG=uk_UA.UTF-8, LC_CTYPE=uk_UA.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.46
ii initramfs-tools [linux-initramfs-tool] 0.109
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-23
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
Reply to: