Bug#730536: gma500: fail to thaw after hibernation, while resume after suspend is ok
Package: src:linux
Version: 3.2.51-1
Severity: normal
Dear Maintainer,
I installed wheezy on an Asus Eeepc 1025c. Everything went almost well during installation, however I registered
several problems about the suspend and hibernation commands: in both cases I always get a scrambled, full of colors
screen with the undergoing system still working. Usually I use the Ctrl-Alt-F1 combination to activate a blind
console in which I login as root and I run a reboot command.
I looked around for a solution and I found a workaround listed in the Debian Wiki for the 1101HA model
(wiki.debian.org/DebianEeePC/Model/1101HA). In this workaround is suggested to create the file
/etc/pm/config.d/gma500 with this line: ADD_PARAMETERS='--quirk-vbestate-restore'. This solves the suspend/resume
problems, but the issue is still present when I try the hibernation/thaw steps.
So, everytime I try to hibernate the computer, it is not possible to thaw the system with a working video.
Thanks in advance.
pkz
-- Package-specific info:
** Version:
Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.51-1
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-686-pae root=UUID=6d54cbc6-e467-4573-ba86-96f992d3bbba ro quiet acpi_osi=Linux
** Not tainted
** Kernel log:
[ 4.238190] gma500 0000:00:02.0: allocated 1024x600 fb
[ 4.238550] fbcon: psbfb (fb0) is primary device
[ 4.478462] usb 1-3: New USB device found, idVendor=04f2, idProduct=b26f
[ 4.478481] usb 1-3: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 4.478497] usb 1-3: Product: USB2.0 0.3M UVC WebCam
[ 4.478509] usb 1-3: Manufacturer: Chicony Electronics Co., Ltd.
[ 4.478521] usb 1-3: SerialNumber: 0x0001
[ 4.534499] Linux media interface: v0.10
[ 4.543269] Linux video capture interface: v2.00
[ 4.548730] uvcvideo: Found UVC 1.00 device USB2.0 0.3M UVC WebCam (04f2:b26f)
[ 4.559725] psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x450f00)
[ 4.567597] input: USB2.0 0.3M UVC WebCam as /devices/pci0000:00/0000:00:1d.7/usb1/1-3/1-3:1.0/input/input6
[ 4.567787] usbcore: registered new interface driver uvcvideo
[ 4.567792] USB Video Class driver (1.1.1)
[ 4.600103] Console: switching to colour frame buffer device 128x37
[ 4.607410] fb0: psbfb frame buffer device
[ 4.607414] drm: registered panic notifier
[ 4.607500] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0
[ 4.607568] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4.607578] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 4.607618] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 4.607704] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000f060
[ 4.607816] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.607825] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.607838] usb usb2: Product: UHCI Host Controller
[ 4.607845] usb usb2: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[ 4.607851] usb usb2: SerialNumber: 0000:00:1d.0
[ 4.608256] hub 2-0:1.0: USB hub found
[ 4.608273] hub 2-0:1.0: 2 ports detected
[ 4.608515] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 4.608526] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.608554] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 4.608638] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000f040
[ 4.608744] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.608753] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.608761] usb usb3: Product: UHCI Host Controller
[ 4.608768] usb usb3: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[ 4.608775] usb usb3: SerialNumber: 0000:00:1d.1
[ 4.609993] hub 3-0:1.0: USB hub found
[ 4.610009] hub 3-0:1.0: 2 ports detected
[ 4.610250] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 4.610261] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.610293] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 4.610379] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000f020
[ 4.610487] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.610496] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.610502] usb usb4: Product: UHCI Host Controller
[ 4.610508] usb usb4: Manufacturer: Linux 3.2.0-4-686-pae uhci_hcd
[ 4.610515] usb usb4: SerialNumber: 0000:00:1d.2
[ 4.611624] hub 4-0:1.0: USB hub found
[ 4.611640] hub 4-0:1.0: 2 ports detected
[ 4.612732] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 4.612784] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[ 4.623848] psmouse serio1: elantech: Synaptics capabilities query result 0x68, 0x15, 0x0a.
[ 4.684059] HDMI status: Codec=1 Pin=3 Presence_Detect=0 ELD_Valid=0
[ 4.684693] input: HDA Intel HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 4.686005] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 4.787710] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input9
[ 5.629829] Adding 4789244k swap on /dev/sda5. Priority:-1 extents:1 across:4789244k SS
[ 5.693570] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 5.823549] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 5.898137] loop: module loaded
[ 8.474010] RPC: Registered named UNIX socket transport module.
[ 8.474019] RPC: Registered udp transport module.
[ 8.474025] RPC: Registered tcp transport module.
[ 8.474030] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 8.484349] FS-Cache: Loaded
[ 8.512767] FS-Cache: Netfs 'nfs' registered for caching
[ 8.530454] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 10.341222] Bluetooth: Core ver 2.16
[ 10.341290] NET: Registered protocol family 31
[ 10.341297] Bluetooth: HCI device and connection manager initialized
[ 10.341305] Bluetooth: HCI socket layer initialized
[ 10.341312] Bluetooth: L2CAP socket layer initialized
[ 10.341534] Bluetooth: SCO socket layer initialized
[ 10.363108] Bluetooth: RFCOMM TTY layer initialized
[ 10.363125] Bluetooth: RFCOMM socket layer initialized
[ 10.363131] Bluetooth: RFCOMM ver 1.11
[ 10.394185] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 10.394193] Bluetooth: BNEP filters: protocol multicast
[ 10.599343] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 10.699471] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input10
[ 10.771642] atl1c 0000:03:00.0: irq 46 for MSI/MSI-X
[ 10.830647] lp: driver loaded but no devices found
[ 10.841163] ppdev: user-space parallel port driver
[ 10.855622] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.959389] wlan0: authenticate with bc:05:43:b5:ea:56 (try 1)
[ 12.961624] wlan0: authenticated
[ 12.978775] wlan0: associate with bc:05:43:b5:ea:56 (try 1)
[ 12.982838] wlan0: RX AssocResp from bc:05:43:b5:ea:56 (capab=0x431 status=0 aid=1)
[ 12.982845] wlan0: associated
[ 12.987906] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 12.988115] cfg80211: Calling CRDA for country: DE
[ 13.051619] cfg80211: Regulatory domain changed to country: DE
[ 13.051629] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.051639] cfg80211: (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 13.051648] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 13.051657] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 13.051665] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[ 23.575333] wlan0: no IPv6 routers present
** Model information
not available
** Loaded modules:
cryptd
aes_i586
aes_generic
parport_pc
ppdev
lp
parport
bnep
rfcomm
bluetooth
cpufreq_stats
cpufreq_userspace
cpufreq_powersave
cpufreq_conservative
uinput
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
loop
joydev
snd_hda_codec_hdmi
snd_hda_codec_realtek
uvcvideo
videodev
media
arc4
eeepc_wmi
asus_wmi
sparse_keymap
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
ath9k
snd_page_alloc
ath9k_common
snd_seq
ath9k_hw
ath
mac80211
cfg80211
psmouse
iTCO_wdt
snd_seq_device
coretemp
serio_raw
evdev
iTCO_vendor_support
rfkill
uhci_hcd
snd_timer
atl1c
battery
ac
gma500_gfx
power_supply
drm_kms_helper
ehci_hcd
video
snd
drm
usbcore
usb_common
acpi_cpufreq
mperf
i2c_algo_bit
soundcore
i2c_core
wmi
button
processor
ext4
crc16
mbcache
jbd2
sd_mod
crc_t10dif
ahci
libahci
libata
scsi_mod
thermal
thermal_sys
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 30:85:a9:83:38:45 brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 74:e5:43:5b:8a:72 brd ff:ff:ff:ff:ff:ff
inet 192.168.178.28/24 brd 192.168.178.255 scope global wlan0
inet6 fe80::76e5:43ff:fe5b:8a72/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 3600 48 0 0 0 0 0 0 3600 48 0 0 0 0 0 0
wlan0: 7809371 10626 0 0 0 0 0 0 775838 5326 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
9131 total packets received
339 with invalid addresses
0 forwarded
0 incoming packets discarded
6416 incoming packets delivered
5216 requests sent out
8 outgoing packets dropped
Icmp:
26 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 26
24 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 24
IcmpMsg:
InType3: 26
OutType3: 24
Tcp:
204 active connections openings
0 passive connection openings
2 failed connection attempts
20 connection resets received
0 connections established
5563 segments received
4736 segments send out
2 segments retransmited
4 bad segments received.
245 resets sent
Udp:
1166 packets received
24 packets to unknown port received.
0 packet receive errors
391 packets sent
UdpLite:
TcpExt:
2 packets pruned from receive queue because of socket buffer overrun
64 TCP sockets finished time wait in fast timer
78 delayed acks sent
1 delayed acks further delayed because of locked socket
Quick ack mode was activated 5 times
3409 packet headers predicted
347 acknowledgments not containing data payload received
128 predicted acknowledgments
2 congestion windows recovered without slow start after partial ack
2 other TCP timeouts
175 packets collapsed in receive queue due to low socket buffer
5 DSACKs sent for old packets
1 DSACKs received
22 connections reset due to unexpected data
20 connections reset due to early user close
TCPSackShiftFallback: 1
TCPChallengeACK: 4
TCPSYNChallenge: 4
IpExt:
InMcastPkts: 99
OutMcastPkts: 81
InBcastPkts: 432
OutBcastPkts: 76
InOctets: 7081428
OutOctets: 589450
InMcastOctets: 11197
OutMcastOctets: 6075
InBcastOctets: 52270
OutBcastOctets: 12602
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Atom Processor D2xxx/N2xxx DRAM Controller [8086:0bf2] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:84a9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller [0300]: Intel Corporation Atom Processor D2xxx/N2xxx Integrated Graphics Controller [8086:0be2] (rev 09) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:84a9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at dfc00000 (32-bit, non-prefetchable) [size=1M]
Region 1: I/O ports at f0c0 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: gma500
00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:8437]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at dff00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: c0400000-c05fffff
Prefetchable memory behind bridge: 00000000c0600000-00000000c07fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: dfe00000-dfefffff
Prefetchable memory behind bridge: 00000000c0200000-00000000c03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: dfd00000-dfdfffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at f060 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at f020 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at dff05000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 43
Region 0: I/O ports at f0b0 [size=8]
Region 1: I/O ports at f0a0 [size=4]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f000 [size=16]
Region 5: Memory at dff04000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller [8086:27da] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:83ad]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 0800 [size=32]
02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01)
Subsystem: Lite-On Communications Inc Device [11ad:6627]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at dfe00000 (64-bit, non-prefetchable) [size=512K]
Expansion ROM at dfe80000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8152 v2.0 Fast Ethernet [1969:2062] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:8468]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at dfd00000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at e000 [size=128]
Capabilities: <access denied>
Kernel driver in use: atl1c
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 04f2:b26f Chicony Electronics Co., Ltd
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 7.2
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-4-686-pae (SMP w/4 CPU cores)
Locale: LANG=it_IT.UTF-8, LC_CTYPE=it_IT.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-686-pae depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.2.0-4-686-pae recommends:
pn firmware-linux-free <none>
ii libc6-i686 2.13-38
Versions of packages linux-image-3.2.0-4-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u2
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-686-pae/postinst/depmod-error-initrd-3.2.0-4-686-pae: false
linux-image-3.2.0-4-686-pae/prerm/removing-running-kernel-3.2.0-4-686-pae: true
linux-image-3.2.0-4-686-pae/postinst/missing-firmware-3.2.0-4-686-pae:
linux-image-3.2.0-4-686-pae/postinst/ignoring-ramdisk:
Reply to: