Bug#730337: linux-image-3.10-3-amd64: Fails to enumerate USB3 device, sometimes hangs the system for seconds
Package: src:linux
Version: 3.10.11-1
Severity: normal
Hi,
attaching a USB3 device mostly results in the following error messages:
[ 1780.947651] usb 2-2: new high-speed USB device number 2 using xhci_hcd
[ 1780.951138] usb 2-2: Device not responding to set address.
[ 1781.154991] usb 2-2: Device not responding to set address.
[ 1781.355397] usb 2-2: device not accepting address 2, error -71
[ 1781.523237] usb 2-2: new high-speed USB device number 3 using xhci_hcd
[ 1781.526723] usb 2-2: Device not responding to set address.
[ 1781.730596] usb 2-2: Device not responding to set address.
[ 1781.931055] usb 2-2: device not accepting address 3, error -71
[ 1782.098888] usb 2-2: new high-speed USB device number 4 using xhci_hcd
[ 1782.102377] usb 2-2: Device not responding to set address.
[ 1782.306311] usb 2-2: Device not responding to set address.
[ 1782.506574] usb 2-2: device not accepting address 4, error -71
[ 1782.674546] usb 2-2: new high-speed USB device number 5 using xhci_hcd
[ 1782.678032] usb 2-2: Device not responding to set address.
[ 1782.881826] usb 2-2: Device not responding to set address.
[ 1783.082313] usb 2-2: device not accepting address 5, error -71
[ 1783.082345] hub 2-0:1.0: unable to enumerate USB device on port 2
Sometimes the system hangs for several seconds when attaching the device. The
sound stutters, the network connection breaks, no input is accepted:
[ 1986.465988] usb 2-1: new high-speed USB device number 14 using xhci_hcd
[ 1986.568645] usb 2-1: New USB device found, idVendor=067b, idProduct=2773
[ 1986.568655] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1986.568661] usb 2-1: Product: USB-SATA Bridge
[ 1986.568665] usb 2-1: Manufacturer: Prolific Technology Inc.
[ 1986.568669] usb 2-1: SerialNumber: PROLIFICMP000000002
[ 1986.570061] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 1986.570195] scsi9 : usb-storage 2-1:1.0
[ 1988.975317] scsi 9:0:0:0: Direct-Access WDC WD30 EZRX-00AZ6B0 80.0 PQ: 0 ANSI: 4
[ 1988.975548] sd 9:0:0:0: Attached scsi generic sg4 type 0
[ 1988.976520] sd 9:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16).
[ 1988.976940] sd 9:0:0:0: [sdd] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 1988.977374] sd 9:0:0:0: [sdd] Write Protect is off
[ 1988.977378] sd 9:0:0:0: [sdd] Mode Sense: 22 00 00 00
[ 1988.977813] sd 9:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1988.978122] sd 9:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16).
[ 1989.088468] sdd: sdd1 sdd2 sdd3
[ 1989.089463] sd 9:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16).
[ 1989.090880] sd 9:0:0:0: [sdd] Attached SCSI disk
[ 1990.048300] usb 2-1: reset high-speed USB device number 14 using xhci_hcd
[ 1995.044916] xhci_hcd 0000:02:00.0: Timeout while waiting for address device command
[ 1995.136795] xhci_hcd 0000:02:00.0: Timeout while waiting for a slot
[ 2005.941021] xhci_hcd 0000:02:00.0: Stopped the command ring failed, maybe the host is dead
[ 2005.941040] xhci_hcd 0000:02:00.0: Abort command ring failed
[ 2005.941051] xhci_hcd 0000:02:00.0: Abort the command ring, but the xHCI is dead.
[ 2005.941212] xhci_hcd 0000:02:00.0: HC died; cleaning up
[ 2005.942363] [sched_delayed] sched: RT throttling activated
[ 2006.346230] usb 2-1: device not accepting address 14, error -22
[ 2006.346342] xHCI xhci_free_dev called with unaddressed device
[ 2006.386255] sd 9:0:0:0: [sdd] Unhandled error code
[ 2006.386263] sd 9:0:0:0: [sdd]
[ 2006.386268] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 2006.386272] sd 9:0:0:0: [sdd] CDB:
[ 2006.386275] Read(16): 88 00 00 00 00 00 07 af 3d 38 00 00 00 f0 00 00
[ 2006.386293] end_request: I/O error, dev sdd, sector 128924984
[ 2006.386299] Buffer I/O error on device sdd2, logical block 121111864
[ 2006.386306] Buffer I/O error on device sdd2, logical block 121111865
[ 2006.386310] Buffer I/O error on device sdd2, logical block 121111866
[ 2006.386314] Buffer I/O error on device sdd2, logical block 121111867
[ 2006.386319] Buffer I/O error on device sdd2, logical block 121111868
[ 2006.386323] Buffer I/O error on device sdd2, logical block 121111869
[ 2006.386327] Buffer I/O error on device sdd2, logical block 121111870
[ 2006.386331] Buffer I/O error on device sdd2, logical block 121111871
[ 2006.386354] Buffer I/O error on device sdd2, logical block 121111872
[ 2006.386359] Buffer I/O error on device sdd2, logical block 121111873
[ 2006.498151] sd 9:0:0:0: [sdd] Unhandled error code
[ 2006.498159] sd 9:0:0:0: [sdd]
[ 2006.498164] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 2006.498168] sd 9:0:0:0: [sdd] CDB:
[ 2006.498170] Read(16): 88 00 00 00 00 00 07 af 3e 28 00 00 00 10 00 00
[ 2006.498188] end_request: I/O error, dev sdd, sector 128925224
[ 2006.542159] sd 9:0:0:0: [sdd] Unhandled error code
[ 2006.542167] sd 9:0:0:0: [sdd]
[ 2006.542171] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 2006.542175] sd 9:0:0:0: [sdd] CDB:
[ 2006.542178] Read(16): 88 00 00 00 00 00 07 af 3e 38 00 00 00 f0 00 00
[ 2006.542196] end_request: I/O error, dev sdd, sector 128925240
[ 2006.582099] sd 9:0:0:0: [sdd] Unhandled error code
[ 2006.582107] sd 9:0:0:0: [sdd]
[ 2006.582111] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 2006.582115] sd 9:0:0:0: [sdd] CDB:
[ 2006.582118] Read(16): 88 00 00 00 00 00 07 af 3f 28 00 00 00 10 00 00
[ 2006.582136] end_request: I/O error, dev sdd, sector 128925480
(this repeats for a few dozen times)
[ 2011.303336] Read(16): 88 00 00 00 00 00 00 77 38 00 00 00 00 08 00 00
[ 2011.343186] xhci_hcd 0000:02:00.0: Timeout while waiting for a slot
[ 2011.343195] xhci_hcd 0000:02:00.0: Abort the command ring, but the xHCI is dead.
[ 2011.343214] xHCI xhci_free_dev called with unaddressed device
[ 2011.343250] sd 9:0:0:0: [sdd] Unhandled error code
[ 2011.343255] sd 9:0:0:0: [sdd]
[ 2011.343258] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 2011.343262] sd 9:0:0:0: [sdd] CDB:
[ 2011.343264] Read(16): 88 00 00 00 00 00 00 77 38 00 00 00 00 08 00 00
[ 2011.383257] sd 9:0:0:0: [sdd] Unhandled error code
[ 2011.383265] sd 9:0:0:0: [sdd]
[ 2011.383270] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 2011.383274] sd 9:0:0:0: [sdd] CDB:
[ 2011.383276] Read(16): 88 00 00 00 00 00 00 77 38 08 00 00 00 08 00 00
(again repeating)
[ 2011.423279] blk_update_request: 110 callbacks suppressed
[ 2011.423284] end_request: I/O error, dev sdd, sector 7813248
[ 2011.423288] quiet_error: 624 callbacks suppressed
[ 2011.423292] Buffer I/O error on device sdd2, logical block 16
[ 2011.463255] sd 9:0:0:0: [sdd] Unhandled error code
[ 2011.463263] sd 9:0:0:0: [sdd]
[ 2011.463267] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 2011.463271] sd 9:0:0:0: [sdd] CDB:
[ 2011.463274] Read(16): 88 00 00 00 00 00 00 77 38 00 00 00 00 08 00 00
[ 2011.463291] end_request: I/O error, dev sdd, sector 7813120
[ 2011.463297] Buffer I/O error on device sdd2, logical block 0
[ 2011.503186] sd 9:0:0:0: [sdd] Unhandled error code
[ 2011.503195] sd 9:0:0:0: [sdd]
[ 2011.503199] Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
[ 2011.503203] sd 9:0:0:0: [sdd] CDB:
[ 2011.503206] Read(16): 88 00 00 00 00 00 00 77 38 00 00 00 00 08 00 00
[ 2011.503223] end_request: I/O error, dev sdd, sector 7813120
[ 2011.503229] Buffer I/O error on device sdd2, logical block 0
(and repeat...)
[ 2016.340382] xhci_hcd 0000:02:00.0: Timeout while waiting for a slot
[ 2016.340391] xhci_hcd 0000:02:00.0: Abort the command ring, but the xHCI is dead.
[ 2016.340411] xHCI xhci_free_dev called with unaddressed device
[ 2021.337426] xhci_hcd 0000:02:00.0: Timeout while waiting for a slot
[ 2021.337436] xhci_hcd 0000:02:00.0: Abort the command ring, but the xHCI is dead.
[ 2021.337457] xHCI xhci_free_dev called with unaddressed device
[ 2021.337471] usb 2-1: USB disconnect, device number 14
And there the system is up again.
After trying long enough (sometimes a dozen tries is not enough) the device
can be attached successfully and is perfectly usable without any further
problems. Attaching it to a USB2 port works without problems.
This problem did already exist with previous kernel versions. If you need any
further information just tell me.
Regards
Alex
-- Package-specific info:
** Version:
Linux version 3.10-3-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.3 (Debian 4.7.3-7) ) #1 SMP Debian 3.10.11-1 (2013-09-10)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.10-3-amd64 root=UUID=2e1b197a-b73b-453b-be49-434d097b319b ro vga=794
** Tainted: PO (4097)
* Proprietary module has been loaded.
* Out-of-tree module has been loaded.
** Model information
sys_vendor: System manufacturer
product_name: System Product Name
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 0801
board_vendor: ASUSTeK Computer INC.
board_name: M5A78L-M/USB3
board_version: Rev X.0x
** Loaded modules:
usb_storage
xhci_hcd
xfs
sha256_generic
ppdev
lp
snd_hrtimer
cpufreq_userspace
cpufreq_stats
cpufreq_powersave
pci_stub
cpufreq_conservative
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
binfmt_misc
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
dns_resolver
fscache
sunrpc
loop
fuse
dm_crypt
dm_mod
snd_hda_codec_hdmi
joydev
acpi_cpufreq
mperf
snd_hda_codec_via
kvm_amd
kvm
snd_hda_intel
snd_hda_codec
nvidia(PO)
evdev
microcode
snd_hwdep
pcspkr
psmouse
snd_pcm_oss
serio_raw
snd_mixer_oss
fam15h_power
edac_mce_amd
sp5100_tco
edac_core
snd_pcm
k10temp
snd_page_alloc
i2c_piix4
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_seq
snd_seq_device
parport_pc
wmi
parport
snd_timer
asus_atk0110
button
processor
i2c_core
snd
thermal_sys
soundcore
ext4
crc16
jbd2
mbcache
btrfs
xor
zlib_deflate
raid6_pq
libcrc32c
sg
sr_mod
sd_mod
crc_t10dif
cdrom
ata_generic
hid_generic
usbhid
hid
crc32c_intel
ghash_clmulni_intel
aesni_intel
aes_x86_64
ablk_helper
cryptd
lrw
gf128mul
glue_helper
ahci
libahci
pata_atiixp
ohci_hcd
ehci_pci
ehci_hcd
usbcore
r8169
mii
libata
scsi_mod
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] RS780 Host Bridge [1022:9600]
Subsystem: ASUSTeK Computer Inc. Device [1043:8388]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780 PCI to PCI bridge (ext gfx port 0) [1022:9603] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fc000000-feafffff
Prefetchable memory behind bridge: 00000000d4000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:07.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 3) [1022:9607] (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: feb00000-febfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0a.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 5) [1022:9609] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Prefetchable memory behind bridge: 00000000faf00000-00000000faffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at c000 [size=8]
Region 1: I/O ports at b000 [size=4]
Region 2: I/O ports at a000 [size=8]
Region 3: I/O ports at 9000 [size=4]
Region 4: I/O ports at 8000 [size=16]
Region 5: Memory at fbfffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:12.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fbfff800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fbffc000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fbffb000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fbfff400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller [1002:4385] (rev 3c)
Subsystem: ASUSTeK Computer Inc. M4A785TD Motherboard [1043:8389]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at ff00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) [1002:4383]
Subsystem: ASUSTeK Computer Inc. M4A785TD Motherboard [1043:836c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fbff4000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller [1002:439d]
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8389]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbffa000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 0 [1022:1600]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 1 [1022:1601]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 2 [1022:1602]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 3 [1022:1603]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k10temp
00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 4 [1022:1604]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: fam15h_power
00:18.5 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 5 [1022:1605]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF116 [GeForce GTX 550 Ti] [10de:1244] (rev a1) (prog-if 00 [VGA controller])
Subsystem: CardExpert Technology Device [10b0:0401]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=32M]
Region 1: Memory at d8000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at d4000000 (64-bit, prefetchable) [size=64M]
Region 5: I/O ports at dc00 [size=128]
[virtual] Expansion ROM at fea80000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nvidia
01:00.1 Audio device [0403]: NVIDIA Corporation GF116 High Definition Audio Controller [10de:0bee] (rev a1)
Subsystem: CardExpert Technology Device [10b0:0401]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fea7c000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
02:00.0 USB controller [0c03]: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller [1b21:1042] (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8488]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at febf0000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
Subsystem: ASUSTeK Computer Inc. P8P67 and other motherboards [1043:8432]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 43
Region 0: I/O ports at e800 [size=256]
Region 2: Memory at fafff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at faff8000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
** USB devices:
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 006: ID 046d:c069 Logitech, Inc. M500 Laser Mouse
Bus 005 Device 002: ID 046d:c31d Logitech, Inc. Media Keyboard K200
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (500, 'testing'), (500, 'stable'), (50, 'unstable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.10-3-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.10-3-amd64 depends on:
ii debconf [debconf-2.0] 1.5.51
ii initramfs-tools [linux-initramfs-tool] 0.115
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.10-3-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.10-3-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u2
ii lilo 1:24.0-2
pn linux-doc-3.10 <none>
Versions of packages linux-image-3.10-3-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information excluded
Reply to: