Package: src:linux
Version: 3.10.5-1
Severity: normal
The Lenovo Yoga 11s laptop boots to a black screen (backlight off)
when i915 loads. This is due to the common backlight control inversion
problem, and can be worked around with i915.invert_brightness=1
This should be enough information to add an entry for this laptop to the
intel_quirks table:
00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core process
or Graphics Controller [8086:0166] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device [17aa:3977]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 2000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
This affects both the kernel I'm running and the one in stable too.
-- Package-specific info:
** Version:
Linux version 3.10-2-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.3 (Debian 4.7.3-6) ) #1 SMP Debian 3.10.5-1 (2013-08-07)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.10-2-amd64 root=UUID=8f9f53ff-f80d-468c-9310-892de8846629 ro quiet i915.invert_brightness=1
** Tainted: WCO (5632)
* Taint on warning.
* Module from drivers/staging has been loaded.
* Out-of-tree module has been loaded.
** Kernel log:
[49876.205573] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[49876.205573] ==> rssi_level:3, rate_bitmap:0x00000ff5
[49882.218012] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[49882.218012] ==> rssi_level:2, rate_bitmap:0x00000ff0
[50050.562890] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[50050.562890] ==> rssi_level:3, rate_bitmap:0x00000ff5
[50056.566202] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[50056.566202] ==> rssi_level:2, rate_bitmap:0x00000ff0
[50311.082032] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[50311.082032] ==> rssi_level:3, rate_bitmap:0x00000ff5
[50335.121810] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[50335.121810] ==> rssi_level:2, rate_bitmap:0x00000ff0
[50515.221777] EXT2-fs (sdf): previous I/O error to superblock detected
[50515.221777]
[50515.221793] EXT2-fs (sdf): error: ext2_readdir: bad page in #2
[50518.567000] EXT2-fs (sdf): previous I/O error to superblock detected
[50518.567000]
[50518.567067] EXT2-fs (sdf): previous I/O error to superblock detected
[50518.567067]
[50518.567093] EXT2-fs (sdf): previous I/O error to superblock detected
[50518.567093]
[50551.844610] EXT2-fs (sde): previous I/O error to superblock detected
[50551.844610]
[50551.844624] EXT2-fs (sde): error: ext2_readdir: bad page in #2
[50562.524764] EXT2-fs (sde): previous I/O error to superblock detected
[50562.524764]
[50562.524776] EXT2-fs (sde): error: ext2_get_inode: unable to read inode block - inode=2, block=129
[50562.524796] EXT2-fs (sde): previous I/O error to superblock detected
[50562.524796]
[50562.524845] EXT2-fs (sde): previous I/O error to superblock detected
[50562.524845]
[50562.524878] EXT2-fs (sde): previous I/O error to superblock detected
[50562.524878]
[50568.515687] EXT2-fs (sdd): previous I/O error to superblock detected
[50568.515687]
[50568.515908] EXT2-fs (sdd): previous I/O error to superblock detected
[50568.515908]
[50568.515940] EXT2-fs (sdd): previous I/O error to superblock detected
[50568.515940]
[50571.209716] EXT2-fs (sdc): previous I/O error to superblock detected
[50571.209716]
[50571.209762] EXT2-fs (sdc): previous I/O error to superblock detected
[50571.209762]
[50571.209781] EXT2-fs (sdc): previous I/O error to superblock detected
[50571.209781]
[50615.856235] usb 1-1.2: new high-speed USB device number 14 using ehci-pci
[50616.598733] usb 1-1.2: New USB device found, idVendor=1058, idProduct=0730
[50616.598740] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[50616.598744] usb 1-1.2: Product: My Passport 0730
[50616.598747] usb 1-1.2: Manufacturer: Western Digital
[50616.598750] usb 1-1.2: SerialNumber: 575842314143305334373633
[50616.599318] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[50616.599629] scsi14 : usb-storage 1-1.2:1.0
[50618.668473] scsi 14:0:0:0: Direct-Access WD My Passport 0730 1012 PQ: 0 ANSI: 6
[50618.669586] scsi 14:0:0:1: Enclosure WD SES Device 1012 PQ: 0 ANSI: 6
[50618.670300] sd 14:0:0:0: Attached scsi generic sg2 type 0
[50618.670817] scsi 14:0:0:1: Attached scsi generic sg3 type 13
[50622.548050] sd 14:0:0:0: [sdc] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB)
[50622.549158] sd 14:0:0:0: [sdc] Write Protect is off
[50622.549167] sd 14:0:0:0: [sdc] Mode Sense: 47 00 10 08
[50622.550498] sd 14:0:0:0: [sdc] No Caching mode page present
[50622.550504] sd 14:0:0:0: [sdc] Assuming drive cache: write through
[50622.554123] sd 14:0:0:0: [sdc] No Caching mode page present
[50622.554141] sd 14:0:0:0: [sdc] Assuming drive cache: write through
[50622.571963] sdc: sdc1
[50622.572682] ses 14:0:0:1: Attached Enclosure device
[50622.575850] sd 14:0:0:0: [sdc] No Caching mode page present
[50622.575856] sd 14:0:0:0: [sdc] Assuming drive cache: write through
[50622.575861] sd 14:0:0:0: [sdc] Attached SCSI disk
[50623.036141] EXT4-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended
[50623.040316] EXT4-fs (sdc1): recovery complete
[50623.044124] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: errors=remount-ro
[51170.789392] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[51170.789392] ==> rssi_level:3, rate_bitmap:0x00000ff5
[51172.794278] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[51172.794278] ==> rssi_level:2, rate_bitmap:0x00000ff0
[51222.894094] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[51222.894094] ==> rssi_level:3, rate_bitmap:0x00000ff5
[51226.902492] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[51226.902492] ==> rssi_level:2, rate_bitmap:0x00000ff0
[51403.261096] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[51403.261096] ==> rssi_level:3, rate_bitmap:0x00000ff5
[51491.437140] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[51491.437140] ==> rssi_level:2, rate_bitmap:0x00000ff0
[51569.679755] usb 1-1.2: USB disconnect, device number 14
[51569.967364] Buffer I/O error on device sdc1, logical block 121667584
[51569.967370] lost page write due to I/O error on sdc1
[51569.967374] JBD2: Error -5 detected when updating journal superblock for sdc1-8.
[51954.353400] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[51954.353400] ==> rssi_level:3, rate_bitmap:0x00000ff5
[51960.365314] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[51960.365314] ==> rssi_level:2, rate_bitmap:0x00000ff0
[52014.473153] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[52014.473153] ==> rssi_level:3, rate_bitmap:0x00000ff5
[52020.486441] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[52020.486441] ==> rssi_level:2, rate_bitmap:0x00000ff0
[54066.569949] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[54066.569949] ==> rssi_level:3, rate_bitmap:0x00000ff5
[54078.593237] UpdateHalRAMask8192CUsb => mac_id:0, networkType:0x03, mask:0x00000fff
[54078.593237] ==> rssi_level:2, rate_bitmap:0x00000ff0
** Model information
sys_vendor: LENOVO
product_name: 20246
product_version: Lenovo IdeaPad Yoga 11S
chassis_vendor: LENOVO
chassis_version: Lenovo IdeaPad Yoga 11S
bios_vendor: LENOVO
bios_version: 77CN19WW(V1.05)
board_vendor: LENOVO
board_name: Yoga2
board_version: 31900003Std
** Loaded modules:
ses
enclosure
8723au(O)
tun
sit
tunnel4
ip_tunnel
bnep
rfcomm
bluetooth
uinput
arc4
rt2800usb
rt2x00usb
rt2800lib
rt2x00lib
mac80211
cfg80211
crc_ccitt
cpuid
ext2
usb_storage
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
dns_resolver
fscache
sunrpc
nls_utf8
nls_cp437
vfat
fat
snd_hda_codec_hdmi
snd_hda_codec_conexant
uvcvideo
videobuf2_vmalloc
videobuf2_memops
videobuf2_core
hid_sensor_hub
videodev
media
joydev
hid_multitouch
hid_generic
usbhid
hid
coretemp
kvm_intel
kvm
crc32c_intel
ghash_clmulni_intel
cryptd
rts5139(C)
iTCO_wdt
iTCO_vendor_support
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
snd_page_alloc
snd_seq
snd_seq_device
snd_timer
psmouse
serio_raw
microcode
evdev
snd
pcspkr
ideapad_laptop
sparse_keymap
rfkill
battery
efivars
wmi
i2c_i801
ac
i915
soundcore
mperf
video
lpc_ich
mfd_core
button
drm_kms_helper
drm
processor
i2c_algo_bit
mei_me
i2c_core
mei
ext4
crc16
jbd2
mbcache
sg
sd_mod
crc_t10dif
thermal
thermal_sys
xhci_hcd
ahci
libahci
ehci_pci
ehci_hcd
libata
usbcore
scsi_mod
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09)
Subsystem: Lenovo Device [17aa:3977]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device [17aa:3977]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 2000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:04.0 Signal processing controller [1180]: Intel Corporation 3rd Gen Core Processor Thermal Subsystem [8086:0153] (rev 09)
Subsystem: Lenovo Device [17aa:3977]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: Memory at cfa08000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Lenovo Device [17aa:3977]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 42
Region 0: Memory at e0400000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: Lenovo Device [17aa:3977]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 41
Region 0: Memory at e041c000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Lenovo Device [17aa:3977]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0421000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: Lenovo Device [17aa:3977]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at e0418000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Lenovo Device [17aa:3977]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at e0420000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge [0601]: Intel Corporation QS77 Express Chipset LPC Controller [8086:1e56] (rev 04)
Subsystem: Lenovo Device [17aa:3977]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Device [17aa:3977]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 40
Region 0: I/O ports at 2088 [size=8]
Region 1: I/O ports at 2094 [size=4]
Region 2: I/O ports at 2080 [size=8]
Region 3: I/O ports at 2090 [size=4]
Region 4: I/O ports at 2060 [size=32]
Region 5: Memory at e041f000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
Subsystem: Lenovo Device [17aa:3977]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 19
Region 0: Memory at e041d000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 2040 [size=32]
00:1f.6 Signal processing controller [1180]: Intel Corporation 7 Series/C210 Series Chipset Family Thermal Management Controller [8086:1e24] (rev 04)
Subsystem: Lenovo Device [17aa:3977]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: Memory at e041e000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
** USB devices:
Bus 002 Device 005: ID 04f2:b35e Chicony Electronics Co., Ltd
Bus 002 Device 004: ID 0bda:1724 Realtek Semiconductor Corp.
Bus 002 Device 003: ID 2047:0855 Texas Instruments
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 004: ID 03eb:8814 Atmel Corp.
Bus 001 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. RTS5129 Card Reader Controller
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.10-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.10-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.50
ii initramfs-tools [linux-initramfs-tool] 0.113
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.10-2-amd64 recommends:
pn firmware-linux-free <none>
Versions of packages linux-image-3.10-2-amd64 suggests:
pn debian-kernel-handbook <none>
pn grub-pc | extlinux | lilo <none>
pn linux-doc-3.10 <none>
Versions of packages linux-image-3.10-2-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
ii firmware-ralink 0.40
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information excluded
--
see shy jo
Attachment:
signature.asc
Description: Digital signature