Package: src:linux Version: 3.10.5-1 Severity: critical Justification: breaks the whole system Dear Maintainer, after upgrading from linux-image-3.9-1-amd64 to linux-image-3.10-2-amd64 the system fails to boot. The Installation of kernel package linux-image-3.10-2-amd64 succeeded and did not return any error. But the system hangs when I try to boot the new kernel (see attached picture). Regards Uwe -- Package-specific info: ** Kernel log: boot messages should be attached ** Model information sys_vendor: Hewlett-Packard product_name: HP Compaq dc5800 Microtower product_version: chassis_vendor: Hewlett-Packard chassis_version: bios_vendor: Hewlett-Packard bios_version: 786F2 v01.51 board_vendor: Hewlett-Packard board_name: 2820h board_version: ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 82Q33 Express DRAM Controller [8086:29d0] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:01.0 PCI bridge [0604]: Intel Corporation 82Q33 Express PCI Express Root Port [8086:29d1] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: f0000000-f2ffffff Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:03.0 Communication controller [0780]: Intel Corporation 82Q33 Express MEI Controller [8086:29d4] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 44 Region 0: Memory at f3025900 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei 00:19.0 Ethernet controller [0200]: Intel Corporation 82566DM-2 Gigabit Network Connection [8086:10bd] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 43 Region 0: Memory at f3000000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at f3024000 (32-bit, non-prefetchable) [size=4K] Region 2: I/O ports at 2100 [size=32] Capabilities: <access denied> Kernel driver in use: e1000e 00:1a.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 4: I/O ports at 2120 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at 2140 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 22 Region 4: I/O ports at 2160 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1a.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 22 Region 0: Memory at f3025000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at f3020000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=20, subordinate=20, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: f8000000-f81fffff Prefetchable memory behind bridge: 00000000f8200000-00000000f83fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=30, subordinate=30, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: f8400000-f85fffff Prefetchable memory behind bridge: 00000000f8600000-00000000f87fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 4: I/O ports at 2180 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 21 Region 4: I/O ports at 21a0 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 22 Region 4: I/O ports at 21c0 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 00:1d.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 20 Region 0: Memory at f3025400 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci-pci 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=32 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge [0601]: Intel Corporation 82801IB (ICH9) LPC Interface Controller [8086:2918] (rev 02) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: lpc_ich 00:1f.2 IDE interface [0101]: Intel Corporation 82801IB (ICH9) 2 port SATA Controller [IDE mode] [8086:2921] (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 Region 4: I/O ports at 2200 [size=16] Region 5: I/O ports at 2210 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 00:1f.5 IDE interface [0101]: Intel Corporation 82801I (ICH9 Family) 2 port SATA Controller [IDE mode] [8086:2926] (rev 02) (prog-if 85 [Master SecO PriO]) Subsystem: Hewlett-Packard Company Device [103c:281e] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 18 Region 0: I/O ports at 2250 [size=8] Region 1: I/O ports at 2268 [size=4] Region 2: I/O ports at 2258 [size=8] Region 3: I/O ports at 226c [size=4] Region 4: I/O ports at 2220 [size=16] Region 5: I/O ports at 2230 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation G86 [Quadro NVS 290] [10de:042f] (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device [10de:0492] Physical Slot: 1 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at f0000000 (64-bit, non-prefetchable) [size=32M] Region 5: I/O ports at 1100 [size=128] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: nvidia ** USB devices: Bus 002 Device 003: ID 0bda:0111 Realtek Semiconductor Corp. RTS5111 Card Reader Controller Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 004: ID 0430:00a2 Sun Microsystems, Inc. Type 7 Keyboard Bus 006 Device 003: ID 046d:c016 Logitech, Inc. Optical Wheel Mouse Bus 006 Device 002: ID 0430:100e Sun Microsystems, Inc. 24.1" LCD Monitor v4 / FID-638 Mouse Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub -- System Information: Debian Release: jessie/sid APT prefers testing APT policy: (750, 'testing'), (650, 'unstable'), (1, 'experimental') Architecture: i386 (x86_64) Kernel: Linux 3.9-1-amd64 (SMP w/2 CPU cores) Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.10-2-amd64 depends on: ii debconf [debconf-2.0] 1.5.50 ii initramfs-tools [linux-initramfs-tool] 0.113 ii kmod 9-3 ii linux-base 3.5 ii module-init-tools 9-3 Versions of packages linux-image-3.10-2-amd64 recommends: ii firmware-linux-free 3.2 ii libc6-i686 2.17-92 Versions of packages linux-image-3.10-2-amd64 suggests: pn debian-kernel-handbook <none> ii grub-pc 1.99-27+deb7u1 pn linux-doc-3.10 <none> Versions of packages linux-image-3.10-2-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.10-2-amd64/postinst/missing-firmware-3.10-2-amd64: linux-image-3.10-2-amd64/postinst/depmod-error-initrd-3.10-2-amd64: false linux-image-3.10-2-amd64/prerm/removing-running-kernel-3.10-2-amd64: true linux-image-3.10-2-amd64/postinst/ignoring-ramdisk:
Attachment:
boot.jpg
Description: JPEG image
