Bug#719627: linux-image-3.10-2-amd64: ten minute delay during boot
Package: src:linux
Version: 3.10.5-1
Severity: important
Dear Maintainer,
This afternoon I installed the linux-image-3.10-2-amd64 package on my
old HP dc5800 small form factor desktop running Debian testing.
As you can see from the attached dmesg output, the 3.10 kernel freezes
for about 10 minutes at a specific point during the boot process. The
computer does not respond to any key strokes during this time. The long
but temporary freeze is completely reproducible; it happens on every
boot/reboot at exactly the same place. Once the kernel has booted the
kernel seems to work fine.
For comparison, I have also attached the dmesg output obtained using the
kernel from linux-image-3.9-1-amd64, which does not freeze.
I'd be happy to try to help you track this down given detailed
instructions, but please note that my technical knowledge is limited.
Thanks for your help.
Matthew
-- Package-specific info:
** Version:
Linux version 3.10-2-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.3 (Debian 4.7.3-6) ) #1 SMP Debian 3.10.5-1 (2013-08-07)
** Command line:
BOOT_IMAGE=/vmlinuz-3.10-2-amd64 root=UUID=b989b59b-22c3-4fa9-9785-805b2d1cddaa ro quiet
** Not tainted
** Kernel log:
[ 608.280299] e1000e 0000:00:19.0: setting latency timer to 64
[ 608.280348] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 608.280362] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 608.510846] [drm] Initialized drm 1.1.0 20060810
[ 608.544031] usb 3-1: new low-speed USB device number 2 using uhci_hcd
[ 608.581971] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:23:7d:46:35:93
[ 608.581974] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 608.581994] e1000e 0000:00:19.0 eth0: MAC: 7, PHY: 6, PBA No: 1042FF-0FF
[ 608.673854] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 608.673857] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 608.674005] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 608.695990] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 608.696062] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 608.720344] usb 3-1: New USB device found, idVendor=03f0, idProduct=0024
[ 608.720349] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 608.720352] usb 3-1: Product: HP Basic USB Keyboard
[ 608.720354] usb 3-1: Manufacturer: CHICONY
[ 608.747245] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 608.796052] tpm_tis 00:09: TPM is disabled/deactivated (0x7)
[ 608.832228] input: HP WMI hotkeys as /devices/virtual/input/input3
[ 608.952392] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x086f00a2
[ 608.952396] nouveau [ DEVICE][0000:01:00.0] Chipset: G86 (NV86)
[ 608.952397] nouveau [ DEVICE][0000:01:00.0] Family : NV50
[ 608.953010] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
[ 608.964588] usb 7-2: new low-speed USB device number 2 using uhci_hcd
[ 608.994701] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
[ 608.994704] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
[ 608.994847] nouveau [ VBIOS][0000:01:00.0] BIT signature found
[ 608.994850] nouveau [ VBIOS][0000:01:00.0] version 60.86.63.00.19
[ 609.014845] nouveau [ PFB][0000:01:00.0] RAM type: DDR2
[ 609.014847] nouveau [ PFB][0000:01:00.0] RAM size: 256 MiB
[ 609.014849] nouveau [ PFB][0000:01:00.0] ZCOMP: 646 tags
[ 609.059211] hidraw: raw HID events driver (C) Jiri Kosina
[ 609.084493] usbcore: registered new interface driver usbhid
[ 609.084495] usbhid: USB HID core driver
[ 609.129106] input: CHICONY HP Basic USB Keyboard as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1:1.0/input/input4
[ 609.129903] hid-generic 0003:03F0:0024.0001: input,hidraw0: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:1a.0-1/input0
[ 609.140877] usb 7-2: New USB device found, idVendor=046d, idProduct=c03d
[ 609.140880] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 609.140882] usb 7-2: Product: USB-PS/2 Optical Mouse
[ 609.140883] usb 7-2: Manufacturer: Logitech
[ 609.147476] hda_codec: AD1884: BIOS auto-probing.
[ 609.149572] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input5
[ 609.153210] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 609.153296] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 609.153379] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 609.153463] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 609.157421] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.0/input/input10
[ 609.157498] hid-generic 0003:046D:C03D.0002: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-2/input0
[ 612.619943] nouveau [ PTHERM][0000:01:00.0] FAN control: PWM
[ 612.619957] nouveau [ PTHERM][0000:01:00.0] fan management: disabled
[ 612.619961] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
[ 612.620112] [TTM] Zone kernel: Available graphics memory: 1989308 kiB
[ 612.620114] [TTM] Initializing pool allocator
[ 612.620120] [TTM] Initializing DMA pool allocator
[ 612.620138] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[ 612.620141] nouveau [ DRM] VRAM: 256 MiB
[ 612.620143] nouveau [ DRM] GART: 512 MiB
[ 612.620148] nouveau [ DRM] TMDS table version 2.0
[ 612.620151] nouveau [ DRM] DCB version 4.0
[ 612.620154] nouveau [ DRM] DCB outp 00: 02011300 00000028
[ 612.620157] nouveau [ DRM] DCB outp 01: 01011302 00000010
[ 612.620160] nouveau [ DRM] DCB outp 02: 01000310 00000028
[ 612.620162] nouveau [ DRM] DCB outp 03: 02000312 00000010
[ 612.620165] nouveau [ DRM] DCB conn 00: 2030
[ 612.620168] nouveau [ DRM] DCB conn 01: 1130
[ 612.628202] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 612.628205] [drm] No driver support for vblank timestamp query.
[ 612.628327] nouveau [ DRM] 2 available performance level(s)
[ 612.628332] nouveau [ DRM] 0: core 208MHz shader 416MHz memory 100MHz fanspeed 100%
[ 612.628336] nouveau [ DRM] 1: core 459MHz shader 918MHz memory 400MHz fanspeed 100%
[ 612.628340] nouveau [ DRM] c: core 459MHz shader 918MHz memory 399MHz fanspeed 100%
[ 612.636305] nouveau [ DRM] MM: using CRYPT for buffer copies
[ 612.679659] nouveau [ DRM] allocated 1920x1080 fb: 0x60000, bo ffff880113068800
[ 612.679716] fbcon: nouveaufb (fb0) is primary device
[ 612.737208] Console: switching to colour frame buffer device 240x67
[ 612.740026] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 612.740028] nouveau 0000:01:00.0: registered panic notifier
[ 612.740034] [drm] Initialized nouveau 1.1.1 20120801 for 0000:01:00.0 on minor 0
[ 613.411556] Adding 3906556k swap on /dev/sda3. Priority:-1 extents:1 across:3906556k
[ 613.440753] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 613.802221] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 614.629907] fuse init (API version 7.22)
[ 614.649960] loop: module loaded
[ 614.907414] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 614.965857] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: user_xattr
[ 615.477267] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 615.539291] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 617.407654] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input11
[ 618.582446] lp: driver loaded but no devices found
[ 618.600143] ppdev: user-space parallel port driver
[ 622.482067] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 622.584073] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 622.584183] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 625.396501] e1000e 0000:00:19.0: setting latency timer to 64
[ 625.396527] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 625.525800] e1000e 0000:00:19.0 eth0: MAC Wakeup cause - Link Status Change
[ 627.128860] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[ 627.128968] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO
[ 627.128996] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
** Model information
sys_vendor: Hewlett-Packard
product_name: HP Compaq dc5800 Small Form Factor
product_version:
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: 786F2 v01.51
board_vendor: Hewlett-Packard
board_name: 2820h
board_version:
** Loaded modules:
cpufreq_stats
cpufreq_powersave
cpufreq_userspace
cpufreq_conservative
parport_pc
ppdev
lp
parport
uinput
xt_tcpudp
nf_conntrack_ipv4
nf_defrag_ipv4
xt_conntrack
nf_conntrack
iptable_filter
ip_tables
x_tables
loop
fuse
snd_hda_codec_analog
hid_generic
usbhid
hid
nouveau
tpm_infineon
snd_hda_intel
sg
hp_wmi
mxm_wmi
snd_hda_codec
sr_mod
cdrom
sparse_keymap
video
snd_hwdep
snd_pcm
snd_page_alloc
ttm
drm_kms_helper
drm
i2c_algo_bit
snd_seq
snd_seq_device
snd_timer
snd
coretemp
psmouse
kvm_intel
serio_raw
e1000e
soundcore
i2c_core
ptp
iTCO_wdt
iTCO_vendor_support
rfkill
mei_me
pps_core
mei
floppy
acpi_cpufreq
kvm
mperf
lpc_ich
evdev
mfd_core
pcspkr
ehci_pci
uhci_hcd
tpm_tis
tpm
tpm_bios
processor
ehci_hcd
thermal_sys
microcode
usbcore
usb_common
wmi
button
ext4
crc16
mbcache
jbd2
sd_mod
crc_t10dif
ata_generic
ata_piix
libata
scsi_mod
** Network interface configuration:
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:23:7d:46:35:93 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.101/24 brd 192.168.1.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::223:7dff:fe46:3593/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
eth0: 1489303 1167 0 0 0 0 0 0 99435 861 0 0 0 0 0 0
lo: 3304 52 0 0 0 0 0 0 3304 52 0 0 0 0 0 0
*** Protocol statistics:
Ip:
1226 total packets received
0 forwarded
0 incoming packets discarded
1199 incoming packets delivered
872 requests sent out
80 dropped because of missing route
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
39 active connections openings
0 passive connection openings
22 failed connection attempts
0 connection resets received
0 connections established
1101 segments received
738 segments send out
17 segments retransmited
1 bad segments received.
34 resets sent
Udp:
98 packets received
0 packets to unknown port received.
0 packet receive errors
122 packets sent
UdpLite:
TcpExt:
9 TCP sockets finished time wait in fast timer
8 delayed acks sent
945 packet headers predicted
44 acknowledgments not containing data payload received
1 predicted acknowledgments
1 times recovered from packet loss by selective acknowledgements
Detected reordering 1 times using time stamp
1 congestion windows fully recovered without slow start
7 congestion windows partially recovered using Hoe heuristic
5 fast retransmits
2 forward retransmits
2 other TCP timeouts
7 DSACKs received
2 connections reset due to unexpected data
TCPSackMerged: 1
TCPSackShiftFallback: 2
TCPRcvCoalesce: 9
TCPOFOQueue: 2
TCPChallengeACK: 1
TCPSYNChallenge: 1
IpExt:
InNoRoutes: 2
InMcastPkts: 24
OutMcastPkts: 26
InBcastPkts: 1
InOctets: 1474675
OutOctets: 81781
InMcastOctets: 3874
OutMcastOctets: 3954
InBcastOctets: 328
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82Q33 Express DRAM Controller [8086:29d0] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 82Q33 Express PCI Express Root Port [8086:29d1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: f0000000-f2ffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:03.0 Communication controller [0780]: Intel Corporation 82Q33 Express MEI Controller [8086:29d4] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f3025900 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
00:19.0 Ethernet controller [0200]: Intel Corporation 82566DM-2 Gigabit Network Connection [8086:10bd] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: Memory at f3000000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f3024000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 2100 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 2120 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 2140 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 2160 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at f3025000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f3020000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f8000000-f81fffff
Prefetchable memory behind bridge: 00000000f8200000-00000000f83fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=30, subordinate=30, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: f8400000-f85fffff
Prefetchable memory behind bridge: 00000000f8600000-00000000f87fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 2180 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 21a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 21c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f3025400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IB (ICH9) LPC Interface Controller [8086:2918] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 IDE interface [0101]: Intel Corporation 82801IB (ICH9) 2 port SATA Controller [IDE mode] [8086:2921] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374
Region 4: I/O ports at 2200 [size=16]
Region 5: I/O ports at 2210 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.5 IDE interface [0101]: Intel Corporation 82801I (ICH9 Family) 2 port SATA Controller [IDE mode] [8086:2926] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:281e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 2250 [size=8]
Region 1: I/O ports at 2268 [size=4]
Region 2: I/O ports at 2258 [size=8]
Region 3: I/O ports at 226c [size=4]
Region 4: I/O ports at 2220 [size=16]
Region 5: I/O ports at 2230 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation G86 [Quadro NVS 290] [10de:042f] (rev a1) (prog-if 00 [VGA controller])
Subsystem: NVIDIA Corporation Device [10de:0492]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f0000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at 1100 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: nouveau
** USB devices:
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 002: ID 046d:c03d Logitech, Inc. M-BT96a Pilot Optical Mouse
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 03f0:0024 Hewlett-Packard KU-0316 Keyboard
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (990, 'testing')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.10-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.10-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.50
ii initramfs-tools [linux-initramfs-tool] 0.113
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.10-2-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.10-2-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u1
pn linux-doc-3.10 <none>
Versions of packages linux-image-3.10-2-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 0.39
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.10-2-amd64/prerm/removing-running-kernel-3.10-2-amd64: true
linux-image-3.10-2-amd64/postinst/missing-firmware-3.10-2-amd64:
linux-image-3.10-2-amd64/postinst/ignoring-ramdisk:
linux-image-3.10-2-amd64/postinst/depmod-error-initrd-3.10-2-amd64: false
[ 0.000000] CPU0 microcode updated early to revision 0xa0b, date = 2010-09-28
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10-2-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.3 (Debian 4.7.3-6) ) #1 SMP Debian 3.10.5-1 (2013-08-07)
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.10-2-amd64 root=UUID=b989b59b-22c3-4fa9-9785-805b2d1cddaa ro quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e8000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000defaff9f] usable
[ 0.000000] BIOS-e820: [mem 0x00000000defb1fa0-0x00000000defb1fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000defb2000-0x00000000dfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f4000000-0x00000000f7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fed3ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed45000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011bffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.5 present.
[ 0.000000] DMI: Hewlett-Packard HP Compaq dc5800 Small Form Factor/2820h, BIOS 786F2 v01.51 08/01/2008
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x11c000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E3FFF write-protect
[ 0.000000] E4000-EFFFF write-back
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F00000000 write-back
[ 0.000000] 1 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 2 base 11C000000 mask FFC000000 uncachable
[ 0.000000] 3 base 100000000 mask FE0000000 write-back
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdefaf max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f9bf0-0x000f9bff] mapped at [ffff8800000f9bf0]
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x0186e000, 0x0186efff] PGTABLE
[ 0.000000] BRK [0x0186f000, 0x0186ffff] PGTABLE
[ 0.000000] BRK [0x01870000, 0x01870fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x11be00000-0x11bffffff]
[ 0.000000] [mem 0x11be00000-0x11bffffff] page 2M
[ 0.000000] BRK [0x01871000, 0x01871fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x118000000-0x11bdfffff]
[ 0.000000] [mem 0x118000000-0x11bdfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x117ffffff]
[ 0.000000] [mem 0x100000000-0x117ffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xdefaefff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0xdedfffff] page 2M
[ 0.000000] [mem 0xdee00000-0xdefaefff] page 4k
[ 0.000000] RAMDISK: [mem 0x37b00000-0x37d77fff]
[ 0.000000] ACPI: RSDP 00000000000e6210 00014 (v00 COMPAQ)
[ 0.000000] ACPI: RSDT 00000000defc2040 00040 (v01 HPQOEM SLIC-BPC 20080801 00000000)
[ 0.000000] ACPI: FACP 00000000defc20e8 00074 (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: DSDT 00000000defc245f 0A0DF (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
[ 0.000000] ACPI: FACS 00000000defc2000 00040
[ 0.000000] ACPI: APIC 00000000defc215c 00084 (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: ASF! 00000000defc21e0 00063 (v32 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: MCFG 00000000defc2243 0003C (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: TCPA 00000000defc227f 00032 (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: SLIC 00000000defc22b1 00176 (v01 HPQOEM SLIC-BPC 00000001 00000000)
[ 0.000000] ACPI: HPET 00000000defc2427 00038 (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000011bffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x11bffffff]
[ 0.000000] NODE_DATA [mem 0x11bff8000-0x11bffbfff]
[ 0.000000] [ffffea0000000000-ffffea0003ffffff] PMD -> [ffff880117600000-ffff88011affffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x11bffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0xdefaefff]
[ 0.000000] node 0: [mem 0x100000000-0x11bffffff]
[ 0.000000] On node 0 totalpages: 1027917
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 12431 pages used for memmap
[ 0.000000] DMA32 zone: 909231 pages, LIFO batch:31
[ 0.000000] Normal zone: 1568 pages used for memmap
[ 0.000000] Normal zone: 114688 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0xf808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e8000
[ 0.000000] PM: Registered nosave memory: 00000000000e8000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000defaf000 - 00000000defb2000
[ 0.000000] PM: Registered nosave memory: 00000000defb2000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f4000000
[ 0.000000] PM: Registered nosave memory: 00000000f4000000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed40000
[ 0.000000] PM: Registered nosave memory: 00000000fed40000 - 00000000fed45000
[ 0.000000] PM: Registered nosave memory: 00000000fed45000 - 0000000100000000
[ 0.000000] e820: [mem 0xe0000000-0xf3ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88011bc00000 s85184 r8192 d21312 u524288
[ 0.000000] pcpu-alloc: s85184 r8192 d21312 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1013841
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.10-2-amd64 root=UUID=b989b59b-22c3-4fa9-9785-805b2d1cddaa ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3974232k/4653056k available (3651k kernel code, 541388k absent, 137436k reserved, 3118k data, 920k init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:33024 nr_irqs:712 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3158.877 MHz processor
[ 0.004003] Calibrating delay loop (skipped), value calculated using timer frequency.. 6317.75 BogoMIPS (lpj=12635508)
[ 0.004006] pid_max: default: 32768 minimum: 301
[ 0.004035] Security Framework initialized
[ 0.004040] AppArmor: AppArmor disabled by boot time parameter
[ 0.004041] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.004306] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.009575] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.010463] Mount-cache hash table entries: 256
[ 0.010658] Initializing cgroup subsys memory
[ 0.010674] Initializing cgroup subsys devices
[ 0.010676] Initializing cgroup subsys freezer
[ 0.010677] Initializing cgroup subsys net_cls
[ 0.010679] Initializing cgroup subsys blkio
[ 0.010680] Initializing cgroup subsys perf_event
[ 0.010710] CPU: Physical Processor ID: 0
[ 0.010711] CPU: Processor Core ID: 0
[ 0.010713] mce: CPU supports 6 MCE banks
[ 0.010720] CPU0: Thermal monitoring enabled (TM2)
[ 0.010727] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
[ 0.010727] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
[ 0.010727] tlb_flushall_shift: -1
[ 0.010785] Freeing SMP alternatives: 12k freed
[ 0.011108] ACPI: Core revision 20130328
[ 0.013291] ACPI: All ACPI Tables successfully acquired
[ 0.016416] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.056236] smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (fam: 06, model: 17, stepping: 0a)
[ 0.060000] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
[ 0.060000] ... version: 2
[ 0.060000] ... bit width: 40
[ 0.060000] ... generic registers: 2
[ 0.060000] ... value mask: 000000ffffffffff
[ 0.060000] ... max period: 000000007fffffff
[ 0.060000] ... fixed-purpose events: 3
[ 0.060000] ... event mask: 0000000700000003
[ 0.008000] CPU1 microcode updated early to revision 0xa0b, date = 2010-09-28
[ 0.060000] smpboot: Booting Node 0, Processors #1
[ 0.072029] Brought up 2 CPUs
[ 0.072033] smpboot: Total of 2 processors activated (12635.50 BogoMIPS)
[ 0.072116] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.080060] devtmpfs: initialized
[ 0.082391] PM: Registering ACPI NVS region [mem 0xdefb1fa0-0xdefb1fff] (96 bytes)
[ 0.082391] reboot: BIOS series board detected. Selecting HP Compaq Laptop-method for reboots.
[ 0.082391] regulator-dummy: no parameters
[ 0.082391] NET: Registered protocol family 16
[ 0.082391] ACPI: bus type PCI registered
[ 0.082391] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.082391] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf4000000-0xf7ffffff] (base 0xf4000000)
[ 0.082391] PCI: MMCONFIG at [mem 0xf4000000-0xf7ffffff] reserved in E820
[ 0.082391] PCI: Using configuration type 1 for base access
[ 0.084048] bio: create slab <bio-0> at 0
[ 0.084048] ACPI: Added _OSI(Module Device)
[ 0.084048] ACPI: Added _OSI(Processor Device)
[ 0.084048] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.084048] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.088070] ACPI: EC: Look up EC in DSDT
[ 0.124052] ACPI: SSDT 00000000defcd368 003AC (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
[ 0.124313] ACPI: Dynamic OEM Table Load:
[ 0.124315] ACPI: SSDT (null) 003AC (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
[ 0.144028] ACPI: SSDT 00000000defcd1ec 0017C (v01 COMPAQ CST 00000001 MSFT 0100000E)
[ 0.144256] ACPI: Dynamic OEM Table Load:
[ 0.144257] ACPI: SSDT (null) 0017C (v01 COMPAQ CST 00000001 MSFT 0100000E)
[ 0.184208] ACPI: Interpreter enabled
[ 0.184214] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130328/hwxface-568)
[ 0.184217] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130328/hwxface-568)
[ 0.184228] ACPI: (supports S0 S3 S4 S5)
[ 0.184230] ACPI: Using IOAPIC for interrupt routing
[ 0.184250] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.184306] ACPI: No dock devices found.
[ 0.196224] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.196276] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20130328/dsfield-211)
[ 0.196280] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff880116e87808), AE_ALREADY_EXISTS (20130328/psparse-537)
[ 0.196285] ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error
[ 0.196289] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20130328/nspredef-307)
[ 0.196605] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.196711] PCI host bridge to bus 0000:00
[ 0.196713] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.196716] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfebfffff]
[ 0.196718] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.196719] pci_bus 0000:00: root bus resource [io 0x1000-0x2fff]
[ 0.196721] pci_bus 0000:00: root bus resource [io 0x3000-0x6fff]
[ 0.196723] pci_bus 0000:00: root bus resource [io 0x7000-0xafff]
[ 0.196725] pci_bus 0000:00: root bus resource [io 0xb000-0xffff]
[ 0.196727] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.196729] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xf3ffffff]
[ 0.196731] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[ 0.196738] pci 0000:00:00.0: [8086:29d0] type 00 class 0x060000
[ 0.196820] pci 0000:00:01.0: [8086:29d1] type 01 class 0x060400
[ 0.196847] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.196868] pci 0000:00:01.0: System wakeup disabled by ACPI
[ 0.196900] pci 0000:00:03.0: [8086:29d4] type 00 class 0x078000
[ 0.196911] pci 0000:00:03.0: reg 10: [mem 0xf3025900-0xf302590f 64bit]
[ 0.196942] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 0.197030] pci 0000:00:19.0: [8086:10bd] type 00 class 0x020000
[ 0.197044] pci 0000:00:19.0: reg 10: [mem 0xf3000000-0xf301ffff]
[ 0.197051] pci 0000:00:19.0: reg 14: [mem 0xf3024000-0xf3024fff]
[ 0.197058] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f]
[ 0.197107] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.197132] pci 0000:00:19.0: System wakeup disabled by ACPI
[ 0.197164] pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300
[ 0.197198] pci 0000:00:1a.0: reg 20: [io 0x2120-0x213f]
[ 0.197259] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 0.197292] pci 0000:00:1a.1: [8086:2938] type 00 class 0x0c0300
[ 0.197326] pci 0000:00:1a.1: reg 20: [io 0x2140-0x215f]
[ 0.197388] pci 0000:00:1a.1: System wakeup disabled by ACPI
[ 0.197421] pci 0000:00:1a.2: [8086:2939] type 00 class 0x0c0300
[ 0.197455] pci 0000:00:1a.2: reg 20: [io 0x2160-0x217f]
[ 0.197517] pci 0000:00:1a.2: System wakeup disabled by ACPI
[ 0.197559] pci 0000:00:1a.7: [8086:293c] type 00 class 0x0c0320
[ 0.197576] pci 0000:00:1a.7: reg 10: [mem 0xf3025000-0xf30253ff]
[ 0.197649] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.197692] pci 0000:00:1a.7: System wakeup disabled by ACPI
[ 0.197728] pci 0000:00:1b.0: [8086:293e] type 00 class 0x040300
[ 0.197740] pci 0000:00:1b.0: reg 10: [mem 0xf3020000-0xf3023fff 64bit]
[ 0.197793] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.197865] pci 0000:00:1c.0: [8086:2940] type 01 class 0x060400
[ 0.197917] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.197945] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.197983] pci 0000:00:1c.1: [8086:2942] type 01 class 0x060400
[ 0.198036] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.198066] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 0.198103] pci 0000:00:1d.0: [8086:2934] type 00 class 0x0c0300
[ 0.198136] pci 0000:00:1d.0: reg 20: [io 0x2180-0x219f]
[ 0.198193] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.198226] pci 0000:00:1d.1: [8086:2935] type 00 class 0x0c0300
[ 0.200011] pci 0000:00:1d.1: reg 20: [io 0x21a0-0x21bf]
[ 0.200070] pci 0000:00:1d.1: System wakeup disabled by ACPI
[ 0.200102] pci 0000:00:1d.2: [8086:2936] type 00 class 0x0c0300
[ 0.200136] pci 0000:00:1d.2: reg 20: [io 0x21c0-0x21df]
[ 0.200195] pci 0000:00:1d.2: System wakeup disabled by ACPI
[ 0.200234] pci 0000:00:1d.7: [8086:293a] type 00 class 0x0c0320
[ 0.200252] pci 0000:00:1d.7: reg 10: [mem 0xf3025400-0xf30257ff]
[ 0.200324] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.200366] pci 0000:00:1d.7: System wakeup disabled by ACPI
[ 0.200398] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.200460] pci 0000:00:1e.0: System wakeup disabled by ACPI
[ 0.200494] pci 0000:00:1f.0: [8086:2918] type 00 class 0x060100
[ 0.200559] pci 0000:00:1f.0: quirk: [io 0xf800-0xf87f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.200564] pci 0000:00:1f.0: quirk: [io 0xfa00-0xfa3f] claimed by ICH6 GPIO
[ 0.200567] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0400 (mask 007f)
[ 0.200570] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0480 (mask 000f)
[ 0.200573] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0cb0 (mask 000f)
[ 0.200634] pci 0000:00:1f.2: [8086:2921] type 00 class 0x01018a
[ 0.200646] pci 0000:00:1f.2: reg 10: [io 0x2240-0x2247]
[ 0.200652] pci 0000:00:1f.2: reg 14: [io 0x2260-0x2263]
[ 0.200659] pci 0000:00:1f.2: reg 18: [io 0x2248-0x224f]
[ 0.200665] pci 0000:00:1f.2: reg 1c: [io 0x2264-0x2267]
[ 0.200671] pci 0000:00:1f.2: reg 20: [io 0x2200-0x220f]
[ 0.200678] pci 0000:00:1f.2: reg 24: [io 0x2210-0x221f]
[ 0.200769] pci 0000:00:1f.5: [8086:2926] type 00 class 0x010185
[ 0.200781] pci 0000:00:1f.5: reg 10: [io 0x2250-0x2257]
[ 0.200788] pci 0000:00:1f.5: reg 14: [io 0x2268-0x226b]
[ 0.200794] pci 0000:00:1f.5: reg 18: [io 0x2258-0x225f]
[ 0.200800] pci 0000:00:1f.5: reg 1c: [io 0x226c-0x226f]
[ 0.200807] pci 0000:00:1f.5: reg 20: [io 0x2220-0x222f]
[ 0.200813] pci 0000:00:1f.5: reg 24: [io 0x2230-0x223f]
[ 0.200951] pci 0000:01:00.0: [10de:042f] type 00 class 0x030000
[ 0.200959] pci 0000:01:00.0: reg 10: [mem 0xf2000000-0xf2ffffff]
[ 0.200968] pci 0000:01:00.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.200977] pci 0000:01:00.0: reg 1c: [mem 0xf0000000-0xf1ffffff 64bit]
[ 0.200983] pci 0000:01:00.0: reg 24: [io 0x1100-0x117f]
[ 0.200990] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.201057] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.201060] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 0.201062] pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf2ffffff]
[ 0.201066] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.201125] pci 0000:00:1c.0: PCI bridge to [bus 20]
[ 0.201190] pci 0000:00:1c.1: PCI bridge to [bus 30]
[ 0.201300] pci 0000:00:1e.0: PCI bridge to [bus 07] (subtractive decode)
[ 0.201308] pci 0000:00:1e.0: bridge window [mem 0xf8000000-0xfebfffff] (subtractive decode)
[ 0.201310] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.201312] pci 0000:00:1e.0: bridge window [io 0x1000-0x2fff] (subtractive decode)
[ 0.201314] pci 0000:00:1e.0: bridge window [io 0x3000-0x6fff] (subtractive decode)
[ 0.201316] pci 0000:00:1e.0: bridge window [io 0x7000-0xafff] (subtractive decode)
[ 0.201318] pci 0000:00:1e.0: bridge window [io 0xb000-0xffff] (subtractive decode)
[ 0.201320] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.201322] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xf3ffffff] (subtractive decode)
[ 0.201324] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[ 0.201387] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20130328/dsfield-211)
[ 0.201391] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff880116e87808), AE_ALREADY_EXISTS (20130328/psparse-537)
[ 0.201398] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20130328/nspredef-307)
[ 0.201402] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.201404] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.201594] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.201650] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 0.201707] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.201762] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.201817] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 0.201873] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.201928] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.201983] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 0.202186] acpi root: \_SB_.PCI0 notify handler is installed
[ 0.202210] Found 1 acpi root devices
[ 0.202641] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.202641] vgaarb: loaded
[ 0.202641] vgaarb: bridge control possible 0000:01:00.0
[ 0.202641] PCI: Using ACPI for IRQ routing
[ 0.202641] PCI: pci_cache_line_size set to 64 bytes
[ 0.202641] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.202641] e820: reserve RAM buffer [mem 0xdefaffa0-0xdfffffff]
[ 0.202641] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.202641] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.202641] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.205009] Switching to clocksource hpet
[ 0.205507] pnp: PnP ACPI init
[ 0.205517] ACPI: bus type PNP registered
[ 0.205552] pnp 00:00: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.205563] pnp 00:01: [dma 4]
[ 0.205580] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.205606] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.205630] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.205656] pnp 00:04: Plug and Play ACPI device, IDs PNP0f13 PNP0f0e (active)
[ 0.205681] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.205875] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 PNP0500 (active)
[ 0.206023] pnp 00:07: [dma 2]
[ 0.206049] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.206104] pnp 00:08: Plug and Play ACPI device, IDs PNP0003 (active)
[ 0.206129] pnp 00:09: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
[ 0.206177] pnp 00:0a: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.206355] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.206374] pnp 00:0c: disabling [io 0xf800-0xf81f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
[ 0.206377] pnp 00:0c: disabling [io 0xf820-0xf83f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
[ 0.206379] pnp 00:0c: disabling [io 0xf840-0xf85f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
[ 0.206381] pnp 00:0c: disabling [io 0xf860-0xf87f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
[ 0.206409] system 00:0c: [io 0x0400-0x041f] has been reserved
[ 0.206411] system 00:0c: [io 0x0420-0x043f] has been reserved
[ 0.206413] system 00:0c: [io 0x0440-0x045f] has been reserved
[ 0.206415] system 00:0c: [io 0x0460-0x047f] has been reserved
[ 0.206418] system 00:0c: [io 0x0480-0x048f] has been reserved
[ 0.206420] system 00:0c: [io 0xfa00-0xfa3f] has been reserved
[ 0.206422] system 00:0c: [io 0xfc00-0xfc7f] has been reserved
[ 0.206424] system 00:0c: [io 0xfc80-0xfcff] has been reserved
[ 0.206427] system 00:0c: [io 0xfe00-0xfe7f] has been reserved
[ 0.206429] system 00:0c: [io 0xfe80-0xfeff] has been reserved
[ 0.206431] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.206477] system 00:0d: [io 0x04d0-0x04d1] has been reserved
[ 0.206479] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 604.096062] system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved
[ 604.096067] system 00:0e: [mem 0x00100000-0xdfffffff] could not be reserved
[ 604.096071] system 00:0e: [mem 0x000e4000-0x000fffff] could not be reserved
[ 604.096074] system 00:0e: [mem 0xfec01000-0xfecfffff] has been reserved
[ 604.096078] system 00:0e: [mem 0xfed00400-0xfed3ffff] has been reserved
[ 604.096082] system 00:0e: [mem 0xfed45000-0xffffffff] has been reserved
[ 604.096085] system 00:0e: [mem 0xf4000000-0xf7ffffff] has been reserved
[ 604.096089] system 00:0e: [mem 0x000cea00-0x000e3fff] has been reserved
[ 604.096093] system 00:0e: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 604.096105] pnp: PnP ACPI: found 15 devices
[ 604.096107] ACPI: bus type PNP unregistered
[ 604.102376] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 20] add_size 1000
[ 604.102380] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 20] add_size 200000
[ 604.102383] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 20] add_size 200000
[ 604.102389] pci 0000:00:1c.1: bridge window [io 0x1000-0x0fff] to [bus 30] add_size 1000
[ 604.102392] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 30] add_size 200000
[ 604.102394] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff] to [bus 30] add_size 200000
[ 604.102404] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 604.102407] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 604.102409] pci 0000:00:1c.1: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 604.102411] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 604.102413] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 604.102416] pci 0000:00:1c.1: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 604.102419] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf8000000-0xf81fffff]
[ 604.102422] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf8200000-0xf83fffff 64bit pref]
[ 604.102424] pci 0000:00:1c.1: BAR 14: assigned [mem 0xf8400000-0xf85fffff]
[ 604.102426] pci 0000:00:1c.1: BAR 15: assigned [mem 0xf8600000-0xf87fffff 64bit pref]
[ 604.102429] pci 0000:00:1c.0: BAR 13: assigned [io 0x3000-0x3fff]
[ 604.102432] pci 0000:00:1c.1: BAR 13: assigned [io 0x4000-0x4fff]
[ 604.102436] pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x20000)
[ 604.102438] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 604.102440] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 604.102443] pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf2ffffff]
[ 604.102446] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 604.102449] pci 0000:00:1c.0: PCI bridge to [bus 20]
[ 604.102452] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 604.102456] pci 0000:00:1c.0: bridge window [mem 0xf8000000-0xf81fffff]
[ 604.102459] pci 0000:00:1c.0: bridge window [mem 0xf8200000-0xf83fffff 64bit pref]
[ 604.102463] pci 0000:00:1c.1: PCI bridge to [bus 30]
[ 604.102466] pci 0000:00:1c.1: bridge window [io 0x4000-0x4fff]
[ 604.102470] pci 0000:00:1c.1: bridge window [mem 0xf8400000-0xf85fffff]
[ 604.102473] pci 0000:00:1c.1: bridge window [mem 0xf8600000-0xf87fffff 64bit pref]
[ 604.102478] pci 0000:00:1e.0: PCI bridge to [bus 07]
[ 604.102721] pci 0000:00:1e.0: setting latency timer to 64
[ 604.102724] pci_bus 0000:00: resource 4 [mem 0xf8000000-0xfebfffff]
[ 604.102726] pci_bus 0000:00: resource 5 [io 0x0000-0x0cf7]
[ 604.102728] pci_bus 0000:00: resource 6 [io 0x1000-0x2fff]
[ 604.102730] pci_bus 0000:00: resource 7 [io 0x3000-0x6fff]
[ 604.102731] pci_bus 0000:00: resource 8 [io 0x7000-0xafff]
[ 604.102733] pci_bus 0000:00: resource 9 [io 0xb000-0xffff]
[ 604.102735] pci_bus 0000:00: resource 10 [mem 0x000a0000-0x000bffff]
[ 604.102737] pci_bus 0000:00: resource 11 [mem 0xe0000000-0xf3ffffff]
[ 604.102739] pci_bus 0000:00: resource 12 [mem 0xfed40000-0xfed44fff]
[ 604.102741] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
[ 604.102743] pci_bus 0000:01: resource 1 [mem 0xf0000000-0xf2ffffff]
[ 604.102745] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
[ 604.102747] pci_bus 0000:20: resource 0 [io 0x3000-0x3fff]
[ 604.102749] pci_bus 0000:20: resource 1 [mem 0xf8000000-0xf81fffff]
[ 604.102751] pci_bus 0000:20: resource 2 [mem 0xf8200000-0xf83fffff 64bit pref]
[ 604.102752] pci_bus 0000:30: resource 0 [io 0x4000-0x4fff]
[ 604.102754] pci_bus 0000:30: resource 1 [mem 0xf8400000-0xf85fffff]
[ 604.102756] pci_bus 0000:30: resource 2 [mem 0xf8600000-0xf87fffff 64bit pref]
[ 604.102758] pci_bus 0000:07: resource 4 [mem 0xf8000000-0xfebfffff]
[ 604.102760] pci_bus 0000:07: resource 5 [io 0x0000-0x0cf7]
[ 604.102762] pci_bus 0000:07: resource 6 [io 0x1000-0x2fff]
[ 604.102764] pci_bus 0000:07: resource 7 [io 0x3000-0x6fff]
[ 604.102765] pci_bus 0000:07: resource 8 [io 0x7000-0xafff]
[ 604.102767] pci_bus 0000:07: resource 9 [io 0xb000-0xffff]
[ 604.102769] pci_bus 0000:07: resource 10 [mem 0x000a0000-0x000bffff]
[ 604.102771] pci_bus 0000:07: resource 11 [mem 0xe0000000-0xf3ffffff]
[ 604.102773] pci_bus 0000:07: resource 12 [mem 0xfed40000-0xfed44fff]
[ 604.102805] NET: Registered protocol family 2
[ 604.102961] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 604.103106] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 604.103218] TCP: Hash tables configured (established 32768 bind 32768)
[ 604.103244] TCP: reno registered
[ 604.103250] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 604.103271] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 604.103336] NET: Registered protocol family 1
[ 604.105166] pci 0000:01:00.0: Boot video device
[ 604.105168] PCI: CLS 64 bytes, default 64
[ 604.105200] Unpacking initramfs...
[ 604.142857] Freeing initrd memory: 2528k freed
[ 604.143365] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 604.143368] software IO TLB [mem 0xdafaf000-0xdefaf000] (64MB) mapped at [ffff8800dafaf000-ffff8800defaefff]
[ 604.143637] audit: initializing netlink socket (disabled)
[ 604.143651] type=2000 audit(1376415943.138:1): initialized
[ 604.154277] bounce pool size: 64 pages
[ 604.154282] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 604.154689] VFS: Disk quotas dquot_6.5.2
[ 604.154709] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 604.154785] msgmni has been set to 7767
[ 604.154965] alg: No test for stdrng (krng)
[ 604.154984] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 604.155009] io scheduler noop registered
[ 604.155011] io scheduler deadline registered
[ 604.155019] io scheduler cfq registered (default)
[ 604.155097] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 604.155143] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 604.155196] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[ 604.155261] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 604.155274] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 604.155329] intel_idle: does not run on family 6 model 23
[ 604.155365] GHES: HEST is not enabled!
[ 604.155412] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 604.175798] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 604.176202] Linux agpgart interface v0.103
[ 604.176346] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 604.179278] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 604.179283] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 604.179385] mousedev: PS/2 mouse device common for all mice
[ 604.179422] rtc_cmos 00:02: RTC can wake from S4
[ 604.179525] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 604.179546] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 604.179555] cpuidle: using governor ladder
[ 604.179556] cpuidle: using governor menu
[ 604.179574] drop_monitor: Initializing network drop monitor service
[ 604.179637] TCP: cubic registered
[ 604.179659] NET: Registered protocol family 10
[ 604.179830] mip6: Mobile IPv6
[ 604.179832] NET: Registered protocol family 17
[ 604.180020] PM: Hibernation image not present or could not be loaded.
[ 604.180026] registered taskstats version 1
[ 604.180509] rtc_cmos 00:02: setting system clock to 2013-08-13 17:45:43 UTC (1376415943)
[ 604.181240] Freeing unused kernel memory: 920k freed
[ 604.181476] Write protecting the kernel read-only data: 6144k
[ 604.182453] Freeing unused kernel memory: 436k freed
[ 604.183559] Freeing unused kernel memory: 488k freed
[ 604.188399] udevd[57]: starting version 175
[ 604.214468] SCSI subsystem initialized
[ 604.215284] ACPI: bus type ATA registered
[ 604.217606] libata version 3.00 loaded.
[ 604.217856] ata_piix 0000:00:1f.2: version 2.13
[ 604.218008] ata_piix 0000:00:1f.2: MAP [
[ 604.218009] P0 -- P1 -- ]
[ 604.218040] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 604.218335] scsi0 : ata_piix
[ 604.219066] scsi1 : ata_piix
[ 604.219127] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2200 irq 14
[ 604.219130] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2208 irq 15
[ 604.219248] ata_piix 0000:00:1f.5: MAP [
[ 604.219249] P0 -- P1 -- ]
[ 604.372039] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 604.372304] scsi2 : ata_piix
[ 604.372353] scsi3 : ata_piix
[ 604.372389] ata3: SATA max UDMA/133 cmd 0x2250 ctl 0x2268 bmdma 0x2220 irq 18
[ 604.372392] ata4: SATA max UDMA/133 cmd 0x2258 ctl 0x226c bmdma 0x2228 irq 18
[ 604.692052] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 604.700121] ata2.00: ATAPI: TSSTcorp CDDVDW TS-H653Q, HC01, max UDMA/100
[ 604.700263] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 604.702546] ata4: SATA link down (SStatus 0 SControl 300)
[ 604.713082] ata3: SATA link down (SStatus 0 SControl 300)
[ 604.713234] ata1.00: ATA-8: WDC WD1600AAJS-60M0A0, 02.03E02, max UDMA/100
[ 604.713236] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 604.720136] ata2.00: configured for UDMA/100
[ 604.728125] ata1.00: configured for UDMA/100
[ 604.728244] scsi 0:0:0:0: Direct-Access ATA WDC WD1600AAJS-6 02.0 PQ: 0 ANSI: 5
[ 604.728931] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW TS-H653Q HC01 PQ: 0 ANSI: 5
[ 604.731913] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 604.731957] sd 0:0:0:0: [sda] Write Protect is off
[ 604.731959] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 604.731978] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 604.751794] sda: sda1 sda2 sda3 sda4
[ 604.752194] sd 0:0:0:0: [sda] Attached SCSI disk
[ 605.111983] PM: Starting manual resume from disk
[ 605.111986] PM: Hibernation image partition 8:3 present
[ 605.111987] PM: Looking for hibernation image.
[ 605.112186] PM: Image not found (code -22)
[ 605.112188] PM: Hibernation image not present or could not be loaded.
[ 605.140014] tsc: Refined TSC clocksource calibration: 3158.749 MHz
[ 605.140020] Switching to clocksource tsc
[ 605.150573] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 606.649743] udevd[337]: starting version 175
[ 607.546738] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 607.546745] ACPI: Power Button [PBTN]
[ 607.546788] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 607.546790] ACPI: Power Button [PWRF]
[ 607.636171] wmi: Mapper loaded
[ 607.663680] ACPI: bus type USB registered
[ 607.663706] usbcore: registered new interface driver usbfs
[ 607.663716] usbcore: registered new interface driver hub
[ 607.663848] usbcore: registered new device driver usb
[ 607.668545] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa0b
[ 607.753936] platform microcode: firmware: agent loaded intel-ucode/06-17-0a into memory
[ 607.753964] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa0b
[ 607.753985] platform microcode: firmware: agent loaded intel-ucode/06-17-0a into memory
[ 607.754057] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 607.804917] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 607.813482] ACPI: Requesting acpi_cpufreq
[ 607.813572] tsc: Marking TSC unstable due to TSC halts in idle
[ 607.813579] ACPI: acpi_idle registered with cpuidle
[ 607.813646] Switching to clocksource hpet
[ 607.836607] tpm_tis 00:09: 1.2 TPM (device-id 0xB, rev-id 16)
[ 607.848702] ehci-pci: EHCI PCI platform driver
[ 607.848745] uhci_hcd: USB Universal Host Controller Interface driver
[ 607.848843] ehci-pci 0000:00:1a.7: setting latency timer to 64
[ 607.848853] ehci-pci 0000:00:1a.7: EHCI Host Controller
[ 607.848860] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 607.848871] ehci-pci 0000:00:1a.7: debug port 1
[ 607.852773] ehci-pci 0000:00:1a.7: cache line size of 64 is not supported
[ 607.852790] ehci-pci 0000:00:1a.7: irq 22, io mem 0xf3025000
[ 607.864027] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 607.864064] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 607.864067] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 607.864070] usb usb1: Product: EHCI Host Controller
[ 607.864073] usb usb1: Manufacturer: Linux 3.10-2-amd64 ehci_hcd
[ 607.864075] usb usb1: SerialNumber: 0000:00:1a.7
[ 607.864215] hub 1-0:1.0: USB hub found
[ 607.864220] hub 1-0:1.0: 6 ports detected
[ 607.864445] ehci-pci 0000:00:1d.7: setting latency timer to 64
[ 607.864451] ehci-pci 0000:00:1d.7: EHCI Host Controller
[ 607.864455] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 607.864465] ehci-pci 0000:00:1d.7: debug port 1
[ 607.868368] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[ 607.868380] ehci-pci 0000:00:1d.7: irq 20, io mem 0xf3025400
[ 607.880022] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 607.880041] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 607.880044] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 607.880047] usb usb2: Product: EHCI Host Controller
[ 607.880050] usb usb2: Manufacturer: Linux 3.10-2-amd64 ehci_hcd
[ 607.880052] usb usb2: SerialNumber: 0000:00:1d.7
[ 607.880177] hub 2-0:1.0: USB hub found
[ 607.880184] hub 2-0:1.0: 6 ports detected
[ 607.881276] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 607.881279] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 607.881284] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 607.881304] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00002120
[ 607.881330] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 607.881332] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 607.881334] usb usb3: Product: UHCI Host Controller
[ 607.881336] usb usb3: Manufacturer: Linux 3.10-2-amd64 uhci_hcd
[ 607.881337] usb usb3: SerialNumber: 0000:00:1a.0
[ 607.881464] hub 3-0:1.0: USB hub found
[ 607.881469] hub 3-0:1.0: 2 ports detected
[ 607.881651] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 607.881654] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 607.881658] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 607.881689] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00002140
[ 607.881714] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 607.881716] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 607.881718] usb usb4: Product: UHCI Host Controller
[ 607.881720] usb usb4: Manufacturer: Linux 3.10-2-amd64 uhci_hcd
[ 607.881722] usb usb4: SerialNumber: 0000:00:1a.1
[ 607.881835] hub 4-0:1.0: USB hub found
[ 607.881839] hub 4-0:1.0: 2 ports detected
[ 607.882015] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 607.882018] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 607.882023] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 607.882043] uhci_hcd 0000:00:1a.2: irq 22, io base 0x00002160
[ 607.882068] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 607.882071] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 607.882072] usb usb5: Product: UHCI Host Controller
[ 607.882074] usb usb5: Manufacturer: Linux 3.10-2-amd64 uhci_hcd
[ 607.882076] usb usb5: SerialNumber: 0000:00:1a.2
[ 607.882193] hub 5-0:1.0: USB hub found
[ 607.882197] hub 5-0:1.0: 2 ports detected
[ 607.882452] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 607.882454] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 607.882459] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 607.882479] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00002180
[ 607.882507] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 607.882509] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 607.882511] usb usb6: Product: UHCI Host Controller
[ 607.882513] usb usb6: Manufacturer: Linux 3.10-2-amd64 uhci_hcd
[ 607.882515] usb usb6: SerialNumber: 0000:00:1d.0
[ 607.882628] hub 6-0:1.0: USB hub found
[ 607.882631] hub 6-0:1.0: 2 ports detected
[ 607.882808] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 607.882811] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 607.882816] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 607.882836] uhci_hcd 0000:00:1d.1: irq 21, io base 0x000021a0
[ 607.882861] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 607.882863] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 607.882865] usb usb7: Product: UHCI Host Controller
[ 607.882867] usb usb7: Manufacturer: Linux 3.10-2-amd64 uhci_hcd
[ 607.882868] usb usb7: SerialNumber: 0000:00:1d.1
[ 607.882948] hub 7-0:1.0: USB hub found
[ 607.882951] hub 7-0:1.0: 2 ports detected
[ 607.883122] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 607.883125] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 607.883129] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 607.883150] uhci_hcd 0000:00:1d.2: irq 22, io base 0x000021c0
[ 607.883174] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 607.883176] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 607.883178] usb usb8: Product: UHCI Host Controller
[ 607.883180] usb usb8: Manufacturer: Linux 3.10-2-amd64 uhci_hcd
[ 607.883181] usb usb8: SerialNumber: 0000:00:1d.2
[ 607.883254] hub 8-0:1.0: USB hub found
[ 607.883258] hub 8-0:1.0: 2 ports detected
[ 607.912051] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 607.968081] tpm_tis 00:09: Adjusting TPM timeout parameters.
[ 608.057956] FDC 0 is a post-1991 82077
[ 608.093106] pps_core: LinuxPPS API ver. 1 registered
[ 608.093108] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 608.173912] iTCO_vendor_support: vendor-support=0
[ 608.186484] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 608.186508] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0xf860)
[ 608.186588] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 608.192946] PTP clock support registered
[ 608.208276] mei_me 0000:00:03.0: setting latency timer to 64
[ 608.208297] mei_me 0000:00:03.0: irq 43 for MSI/MSI-X
[ 608.249753] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 608.249755] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 608.280299] e1000e 0000:00:19.0: setting latency timer to 64
[ 608.280348] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 608.280362] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 608.510846] [drm] Initialized drm 1.1.0 20060810
[ 608.544031] usb 3-1: new low-speed USB device number 2 using uhci_hcd
[ 608.581971] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:23:7d:46:35:93
[ 608.581974] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 608.581994] e1000e 0000:00:19.0 eth0: MAC: 7, PHY: 6, PBA No: 1042FF-0FF
[ 608.673854] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 608.673857] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 608.674005] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 608.695990] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 608.696062] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 608.720344] usb 3-1: New USB device found, idVendor=03f0, idProduct=0024
[ 608.720349] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 608.720352] usb 3-1: Product: HP Basic USB Keyboard
[ 608.720354] usb 3-1: Manufacturer: CHICONY
[ 608.747245] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 608.796052] tpm_tis 00:09: TPM is disabled/deactivated (0x7)
[ 608.832228] input: HP WMI hotkeys as /devices/virtual/input/input3
[ 608.952392] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x086f00a2
[ 608.952396] nouveau [ DEVICE][0000:01:00.0] Chipset: G86 (NV86)
[ 608.952397] nouveau [ DEVICE][0000:01:00.0] Family : NV50
[ 608.953010] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
[ 608.964588] usb 7-2: new low-speed USB device number 2 using uhci_hcd
[ 608.994701] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
[ 608.994704] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
[ 608.994847] nouveau [ VBIOS][0000:01:00.0] BIT signature found
[ 608.994850] nouveau [ VBIOS][0000:01:00.0] version 60.86.63.00.19
[ 609.014845] nouveau [ PFB][0000:01:00.0] RAM type: DDR2
[ 609.014847] nouveau [ PFB][0000:01:00.0] RAM size: 256 MiB
[ 609.014849] nouveau [ PFB][0000:01:00.0] ZCOMP: 646 tags
[ 609.059211] hidraw: raw HID events driver (C) Jiri Kosina
[ 609.084493] usbcore: registered new interface driver usbhid
[ 609.084495] usbhid: USB HID core driver
[ 609.129106] input: CHICONY HP Basic USB Keyboard as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1:1.0/input/input4
[ 609.129903] hid-generic 0003:03F0:0024.0001: input,hidraw0: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:1a.0-1/input0
[ 609.140877] usb 7-2: New USB device found, idVendor=046d, idProduct=c03d
[ 609.140880] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 609.140882] usb 7-2: Product: USB-PS/2 Optical Mouse
[ 609.140883] usb 7-2: Manufacturer: Logitech
[ 609.147476] hda_codec: AD1884: BIOS auto-probing.
[ 609.149572] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input5
[ 609.153210] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 609.153296] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 609.153379] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 609.153463] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 609.157421] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb7/7-2/7-2:1.0/input/input10
[ 609.157498] hid-generic 0003:046D:C03D.0002: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-2/input0
[ 612.619943] nouveau [ PTHERM][0000:01:00.0] FAN control: PWM
[ 612.619957] nouveau [ PTHERM][0000:01:00.0] fan management: disabled
[ 612.619961] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
[ 612.620112] [TTM] Zone kernel: Available graphics memory: 1989308 kiB
[ 612.620114] [TTM] Initializing pool allocator
[ 612.620120] [TTM] Initializing DMA pool allocator
[ 612.620138] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[ 612.620141] nouveau [ DRM] VRAM: 256 MiB
[ 612.620143] nouveau [ DRM] GART: 512 MiB
[ 612.620148] nouveau [ DRM] TMDS table version 2.0
[ 612.620151] nouveau [ DRM] DCB version 4.0
[ 612.620154] nouveau [ DRM] DCB outp 00: 02011300 00000028
[ 612.620157] nouveau [ DRM] DCB outp 01: 01011302 00000010
[ 612.620160] nouveau [ DRM] DCB outp 02: 01000310 00000028
[ 612.620162] nouveau [ DRM] DCB outp 03: 02000312 00000010
[ 612.620165] nouveau [ DRM] DCB conn 00: 2030
[ 612.620168] nouveau [ DRM] DCB conn 01: 1130
[ 612.628202] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 612.628205] [drm] No driver support for vblank timestamp query.
[ 612.628327] nouveau [ DRM] 2 available performance level(s)
[ 612.628332] nouveau [ DRM] 0: core 208MHz shader 416MHz memory 100MHz fanspeed 100%
[ 612.628336] nouveau [ DRM] 1: core 459MHz shader 918MHz memory 400MHz fanspeed 100%
[ 612.628340] nouveau [ DRM] c: core 459MHz shader 918MHz memory 399MHz fanspeed 100%
[ 612.636305] nouveau [ DRM] MM: using CRYPT for buffer copies
[ 612.679659] nouveau [ DRM] allocated 1920x1080 fb: 0x60000, bo ffff880113068800
[ 612.679716] fbcon: nouveaufb (fb0) is primary device
[ 612.737208] Console: switching to colour frame buffer device 240x67
[ 612.740026] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 612.740028] nouveau 0000:01:00.0: registered panic notifier
[ 612.740034] [drm] Initialized nouveau 1.1.1 20120801 for 0000:01:00.0 on minor 0
[ 613.411556] Adding 3906556k swap on /dev/sda3. Priority:-1 extents:1 across:3906556k
[ 613.440753] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 613.802221] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 614.629907] fuse init (API version 7.22)
[ 614.649960] loop: module loaded
[ 614.907414] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 614.965857] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: user_xattr
[ 615.477267] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 615.539291] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 617.407654] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input11
[ 618.582446] lp: driver loaded but no devices found
[ 618.600143] ppdev: user-space parallel port driver
[ 622.482067] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 622.584073] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 622.584183] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 625.396501] e1000e 0000:00:19.0: setting latency timer to 64
[ 625.396527] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 625.525800] e1000e 0000:00:19.0 eth0: MAC Wakeup cause - Link Status Change
[ 627.128860] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[ 627.128968] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO
[ 627.128996] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 0.000000] CPU0 microcode updated early to revision 0xa0b, date = 2010-09-28
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.9-1-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.3 (Debian 4.7.3-5) ) #1 SMP Debian 3.9.8-1
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.9-1-amd64 root=UUID=b989b59b-22c3-4fa9-9785-805b2d1cddaa ro quiet
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e8000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000defaff9f] usable
[ 0.000000] BIOS-e820: [mem 0x00000000defb1fa0-0x00000000defb1fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000defb2000-0x00000000dfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f4000000-0x00000000f7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fed3ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed45000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011bffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.5 present.
[ 0.000000] DMI: Hewlett-Packard HP Compaq dc5800 Small Form Factor/2820h, BIOS 786F2 v01.51 08/01/2008
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x11c000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E3FFF write-protect
[ 0.000000] E4000-EFFFF write-back
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F00000000 write-back
[ 0.000000] 1 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 2 base 11C000000 mask FFC000000 uncachable
[ 0.000000] 3 base 100000000 mask FE0000000 write-back
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdefaf max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f9bf0-0x000f9bff] mapped at [ffff8800000f9bf0]
[ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x01859000, 0x01859fff] PGTABLE
[ 0.000000] BRK [0x0185a000, 0x0185afff] PGTABLE
[ 0.000000] BRK [0x0185b000, 0x0185bfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x11be00000-0x11bffffff]
[ 0.000000] [mem 0x11be00000-0x11bffffff] page 2M
[ 0.000000] BRK [0x0185c000, 0x0185cfff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x118000000-0x11bdfffff]
[ 0.000000] [mem 0x118000000-0x11bdfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x117ffffff]
[ 0.000000] [mem 0x100000000-0x117ffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xdefaefff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0xdedfffff] page 2M
[ 0.000000] [mem 0xdee00000-0xdefaefff] page 4k
[ 0.000000] RAMDISK: [mem 0x37b02000-0x37d78fff]
[ 0.000000] ACPI: RSDP 00000000000e6210 00014 (v00 COMPAQ)
[ 0.000000] ACPI: RSDT 00000000defc2040 00040 (v01 HPQOEM SLIC-BPC 20080801 00000000)
[ 0.000000] ACPI: FACP 00000000defc20e8 00074 (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: DSDT 00000000defc245f 0A0DF (v01 COMPAQ DSDT_PRJ 00000001 MSFT 0100000E)
[ 0.000000] ACPI: FACS 00000000defc2000 00040
[ 0.000000] ACPI: APIC 00000000defc215c 00084 (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: ASF! 00000000defc21e0 00063 (v32 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: MCFG 00000000defc2243 0003C (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: TCPA 00000000defc227f 00032 (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: SLIC 00000000defc22b1 00176 (v01 HPQOEM SLIC-BPC 00000001 00000000)
[ 0.000000] ACPI: HPET 00000000defc2427 00038 (v01 COMPAQ BEARLAKE 00000001 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000011bffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x11bffffff]
[ 0.000000] NODE_DATA [mem 0x11bff8000-0x11bffbfff]
[ 0.000000] [ffffea0000000000-ffffea0003ffffff] PMD -> [ffff880117600000-ffff88011affffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x11bffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0xdefaefff]
[ 0.000000] node 0: [mem 0x100000000-0x11bffffff]
[ 0.000000] On node 0 totalpages: 1027917
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 12431 pages used for memmap
[ 0.000000] DMA32 zone: 909231 pages, LIFO batch:31
[ 0.000000] Normal zone: 1568 pages used for memmap
[ 0.000000] Normal zone: 114688 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0xf808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e8000
[ 0.000000] PM: Registered nosave memory: 00000000000e8000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000defaf000 - 00000000defb2000
[ 0.000000] PM: Registered nosave memory: 00000000defb2000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f4000000
[ 0.000000] PM: Registered nosave memory: 00000000f4000000 - 00000000f8000000
[ 0.000000] PM: Registered nosave memory: 00000000f8000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fed40000
[ 0.000000] PM: Registered nosave memory: 00000000fed40000 - 00000000fed45000
[ 0.000000] PM: Registered nosave memory: 00000000fed45000 - 0000000100000000
[ 0.000000] e820: [mem 0xe0000000-0xf3ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88011bc00000 s84800 r8192 d21696 u524288
[ 0.000000] pcpu-alloc: s84800 r8192 d21696 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1013841
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.9-1-amd64 root=UUID=b989b59b-22c3-4fa9-9785-805b2d1cddaa ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] xsave: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3974320k/4653056k available (3646k kernel code, 541388k absent, 137348k reserved, 3109k data, 880k init)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:33024 nr_irqs:712 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 3158.419 MHz processor
[ 0.004003] Calibrating delay loop (skipped), value calculated using timer frequency.. 6316.83 BogoMIPS (lpj=12633676)
[ 0.004005] pid_max: default: 32768 minimum: 301
[ 0.004035] Security Framework initialized
[ 0.004040] AppArmor: AppArmor disabled by boot time parameter
[ 0.004041] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.004293] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.009337] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.010225] Mount-cache hash table entries: 256
[ 0.010416] Initializing cgroup subsys cpuacct
[ 0.010419] Initializing cgroup subsys memory
[ 0.010433] Initializing cgroup subsys devices
[ 0.010435] Initializing cgroup subsys freezer
[ 0.010436] Initializing cgroup subsys net_cls
[ 0.010438] Initializing cgroup subsys blkio
[ 0.010440] Initializing cgroup subsys perf_event
[ 0.010467] CPU: Physical Processor ID: 0
[ 0.010468] CPU: Processor Core ID: 0
[ 0.010470] mce: CPU supports 6 MCE banks
[ 0.010477] CPU0: Thermal monitoring enabled (TM2)
[ 0.010484] Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
[ 0.010484] Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32
[ 0.010484] tlb_flushall_shift: -1
[ 0.010542] Freeing SMP alternatives: 12k freed
[ 0.010860] ACPI: Core revision 20130117
[ 0.012925] ACPI: All ACPI Tables successfully acquired
[ 0.016175] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.055857] smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (fam: 06, model: 17, stepping: 0a)
[ 0.056000] Performance Events: PEBS fmt0+, 4-deep LBR, Core2 events, Intel PMU driver.
[ 0.056000] ... version: 2
[ 0.056000] ... bit width: 40
[ 0.056000] ... generic registers: 2
[ 0.056000] ... value mask: 000000ffffffffff
[ 0.056000] ... max period: 000000007fffffff
[ 0.056000] ... fixed-purpose events: 3
[ 0.056000] ... event mask: 0000000700000003
[ 0.008000] CPU1 microcode updated early to revision 0xa0b, date = 2010-09-28
[ 0.056000] smpboot: Booting Node 0, Processors #1
[ 0.068022] Brought up 2 CPUs
[ 0.068026] smpboot: Total of 2 processors activated (12633.67 BogoMIPS)
[ 0.068111] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.072086] devtmpfs: initialized
[ 0.074351] PM: Registering ACPI NVS region [mem 0xdefb1fa0-0xdefb1fff] (96 bytes)
[ 0.074351] reboot: BIOS series board detected. Selecting HP Compaq Laptop-method for reboots.
[ 0.074351] regulator-dummy: no parameters
[ 0.074351] NET: Registered protocol family 16
[ 0.074351] ACPI: bus type PCI registered
[ 0.074351] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf4000000-0xf7ffffff] (base 0xf4000000)
[ 0.074351] PCI: MMCONFIG at [mem 0xf4000000-0xf7ffffff] reserved in E820
[ 0.074351] PCI: Using configuration type 1 for base access
[ 0.076026] bio: create slab <bio-0> at 0
[ 0.076052] ACPI: Added _OSI(Module Device)
[ 0.076052] ACPI: Added _OSI(Processor Device)
[ 0.076052] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.076052] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.080257] ACPI: EC: Look up EC in DSDT
[ 0.084052] ACPI: SSDT 00000000defcd368 003AC (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
[ 0.084314] ACPI: Dynamic OEM Table Load:
[ 0.084316] ACPI: SSDT (null) 003AC (v01 COMPAQ CPU_TM2 00000001 MSFT 0100000E)
[ 0.084331] ACPI: SSDT 00000000defcd1ec 0017C (v01 COMPAQ CST 00000001 MSFT 0100000E)
[ 0.084331] ACPI: Dynamic OEM Table Load:
[ 0.084331] ACPI: SSDT (null) 0017C (v01 COMPAQ CST 00000001 MSFT 0100000E)
[ 0.092187] ACPI: Interpreter enabled
[ 0.092196] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130117/hwxface-568)
[ 0.092205] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130117/hwxface-568)
[ 0.092214] ACPI: (supports S0 S3 S4 S5)
[ 0.092216] ACPI: Using IOAPIC for interrupt routing
[ 0.092237] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.096239] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.096239] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20130117/dsfield-211)
[ 0.096239] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff880116e80808), AE_ALREADY_EXISTS (20130117/psparse-537)
[ 0.096239] ACPI: Marking method _OSC as Serialized because of AE_ALREADY_EXISTS error
[ 0.096239] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20130117/nspredef-337)
[ 0.096485] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
[ 0.096517] PCI host bridge to bus 0000:00
[ 0.096520] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.096522] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xfebfffff]
[ 0.096524] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.096526] pci_bus 0000:00: root bus resource [io 0x1000-0x2fff]
[ 0.096528] pci_bus 0000:00: root bus resource [io 0x3000-0x6fff]
[ 0.096530] pci_bus 0000:00: root bus resource [io 0x7000-0xafff]
[ 0.096532] pci_bus 0000:00: root bus resource [io 0xb000-0xffff]
[ 0.096533] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.096535] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xf3ffffff]
[ 0.096537] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[ 0.096545] pci 0000:00:00.0: [8086:29d0] type 00 class 0x060000
[ 0.096626] pci 0000:00:01.0: [8086:29d1] type 01 class 0x060400
[ 0.096654] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.096674] pci 0000:00:01.0: System wakeup disabled by ACPI
[ 0.096707] pci 0000:00:03.0: [8086:29d4] type 00 class 0x078000
[ 0.096718] pci 0000:00:03.0: reg 10: [mem 0xf3025900-0xf302590f 64bit]
[ 0.096749] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 0.096837] pci 0000:00:19.0: [8086:10bd] type 00 class 0x020000
[ 0.096852] pci 0000:00:19.0: reg 10: [mem 0xf3000000-0xf301ffff]
[ 0.096859] pci 0000:00:19.0: reg 14: [mem 0xf3024000-0xf3024fff]
[ 0.096866] pci 0000:00:19.0: reg 18: [io 0x2100-0x211f]
[ 0.096915] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.096939] pci 0000:00:19.0: System wakeup disabled by ACPI
[ 0.096973] pci 0000:00:1a.0: [8086:2937] type 00 class 0x0c0300
[ 0.097007] pci 0000:00:1a.0: reg 20: [io 0x2120-0x213f]
[ 0.097066] pci 0000:00:1a.0: System wakeup disabled by ACPI
[ 0.097100] pci 0000:00:1a.1: [8086:2938] type 00 class 0x0c0300
[ 0.097134] pci 0000:00:1a.1: reg 20: [io 0x2140-0x215f]
[ 0.097194] pci 0000:00:1a.1: System wakeup disabled by ACPI
[ 0.097227] pci 0000:00:1a.2: [8086:2939] type 00 class 0x0c0300
[ 0.097261] pci 0000:00:1a.2: reg 20: [io 0x2160-0x217f]
[ 0.097323] pci 0000:00:1a.2: System wakeup disabled by ACPI
[ 0.097363] pci 0000:00:1a.7: [8086:293c] type 00 class 0x0c0320
[ 0.097380] pci 0000:00:1a.7: reg 10: [mem 0xf3025000-0xf30253ff]
[ 0.097453] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.097497] pci 0000:00:1a.7: System wakeup disabled by ACPI
[ 0.097497] pci 0000:00:1b.0: [8086:293e] type 00 class 0x040300
[ 0.097497] pci 0000:00:1b.0: reg 10: [mem 0xf3020000-0xf3023fff 64bit]
[ 0.097497] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.097497] pci 0000:00:1c.0: [8086:2940] type 01 class 0x060400
[ 0.097497] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.097497] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.097497] pci 0000:00:1c.1: [8086:2942] type 01 class 0x060400
[ 0.097497] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.097497] pci 0000:00:1c.1: System wakeup disabled by ACPI
[ 0.097497] pci 0000:00:1d.0: [8086:2934] type 00 class 0x0c0300
[ 0.097497] pci 0000:00:1d.0: reg 20: [io 0x2180-0x219f]
[ 0.097497] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.097497] pci 0000:00:1d.1: [8086:2935] type 00 class 0x0c0300
[ 0.097497] pci 0000:00:1d.1: reg 20: [io 0x21a0-0x21bf]
[ 0.097497] pci 0000:00:1d.1: System wakeup disabled by ACPI
[ 0.097497] pci 0000:00:1d.2: [8086:2936] type 00 class 0x0c0300
[ 0.097497] pci 0000:00:1d.2: reg 20: [io 0x21c0-0x21df]
[ 0.097497] pci 0000:00:1d.2: System wakeup disabled by ACPI
[ 0.097497] pci 0000:00:1d.7: [8086:293a] type 00 class 0x0c0320
[ 0.097497] pci 0000:00:1d.7: reg 10: [mem 0xf3025400-0xf30257ff]
[ 0.097497] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.097497] pci 0000:00:1d.7: System wakeup disabled by ACPI
[ 0.097497] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.097497] pci 0000:00:1e.0: System wakeup disabled by ACPI
[ 0.097497] pci 0000:00:1f.0: [8086:2918] type 00 class 0x060100
[ 0.097497] pci 0000:00:1f.0: quirk: [io 0xf800-0xf87f] claimed by ICH6 ACPI/GPIO/TCO
[ 0.097497] pci 0000:00:1f.0: quirk: [io 0xfa00-0xfa3f] claimed by ICH6 GPIO
[ 0.097497] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0400 (mask 007f)
[ 0.097497] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0480 (mask 000f)
[ 0.097497] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 0cb0 (mask 000f)
[ 0.097497] pci 0000:00:1f.2: [8086:2921] type 00 class 0x01018a
[ 0.097497] pci 0000:00:1f.2: reg 10: [io 0x2240-0x2247]
[ 0.097497] pci 0000:00:1f.2: reg 14: [io 0x2260-0x2263]
[ 0.097497] pci 0000:00:1f.2: reg 18: [io 0x2248-0x224f]
[ 0.097497] pci 0000:00:1f.2: reg 1c: [io 0x2264-0x2267]
[ 0.097497] pci 0000:00:1f.2: reg 20: [io 0x2200-0x220f]
[ 0.097497] pci 0000:00:1f.2: reg 24: [io 0x2210-0x221f]
[ 0.097497] pci 0000:00:1f.5: [8086:2926] type 00 class 0x010185
[ 0.097497] pci 0000:00:1f.5: reg 10: [io 0x2250-0x2257]
[ 0.097497] pci 0000:00:1f.5: reg 14: [io 0x2268-0x226b]
[ 0.097497] pci 0000:00:1f.5: reg 18: [io 0x2258-0x225f]
[ 0.097497] pci 0000:00:1f.5: reg 1c: [io 0x226c-0x226f]
[ 0.097497] pci 0000:00:1f.5: reg 20: [io 0x2220-0x222f]
[ 0.097497] pci 0000:00:1f.5: reg 24: [io 0x2230-0x223f]
[ 0.097497] pci 0000:01:00.0: [10de:042f] type 00 class 0x030000
[ 0.097497] pci 0000:01:00.0: reg 10: [mem 0xf2000000-0xf2ffffff]
[ 0.097497] pci 0000:01:00.0: reg 14: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.097498] pci 0000:01:00.0: reg 1c: [mem 0xf0000000-0xf1ffffff 64bit]
[ 0.097504] pci 0000:01:00.0: reg 24: [io 0x1100-0x117f]
[ 0.097510] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.097577] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.097580] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 0.097583] pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf2ffffff]
[ 0.097586] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.097628] pci 0000:00:1c.0: PCI bridge to [bus 20]
[ 0.097677] pci 0000:00:1c.1: PCI bridge to [bus 30]
[ 0.097742] pci 0000:00:1e.0: PCI bridge to [bus 07] (subtractive decode)
[ 0.097750] pci 0000:00:1e.0: bridge window [mem 0xf8000000-0xfebfffff] (subtractive decode)
[ 0.097752] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.097754] pci 0000:00:1e.0: bridge window [io 0x1000-0x2fff] (subtractive decode)
[ 0.097756] pci 0000:00:1e.0: bridge window [io 0x3000-0x6fff] (subtractive decode)
[ 0.097758] pci 0000:00:1e.0: bridge window [io 0x7000-0xafff] (subtractive decode)
[ 0.097760] pci 0000:00:1e.0: bridge window [io 0xb000-0xffff] (subtractive decode)
[ 0.097763] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.097765] pci 0000:00:1e.0: bridge window [mem 0xe0000000-0xf3ffffff] (subtractive decode)
[ 0.097767] pci 0000:00:1e.0: bridge window [mem 0xfed40000-0xfed44fff] (subtractive decode)
[ 0.097828] ACPI Error: [CAPD] Namespace lookup failure, AE_ALREADY_EXISTS (20130117/dsfield-211)
[ 0.097832] ACPI Error: Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff880116e80808), AE_ALREADY_EXISTS (20130117/psparse-537)
[ 0.097838] ACPI Warning: For \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20130117/nspredef-337)
[ 0.097842] acpi PNP0A08:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.097844] acpi PNP0A08:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.098176] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.098228] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 0.098281] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.098333] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.098385] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 0.098437] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 0.098488] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 0.098540] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 0.098741] acpi root: \_SB_.PCI0 notify handler is installed
[ 0.098764] Found 1 acpi root devices
[ 0.099219] ACPI: No dock devices found.
[ 0.100014] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.100016] vgaarb: loaded
[ 0.100017] vgaarb: bridge control possible 0000:01:00.0
[ 0.100049] PCI: Using ACPI for IRQ routing
[ 0.100413] PCI: pci_cache_line_size set to 64 bytes
[ 0.100450] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.100452] e820: reserve RAM buffer [mem 0xdefaffa0-0xdfffffff]
[ 0.100550] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.100553] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 0.100557] hpet0: 4 comparators, 64-bit 14.318180 MHz counter
[ 0.104008] Switching to clocksource hpet
[ 0.105646] pnp: PnP ACPI init
[ 0.105656] ACPI: bus type PNP registered
[ 0.105693] pnp 00:00: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.105705] pnp 00:01: [dma 4]
[ 0.105722] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.105750] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.105771] pnp 00:03: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.105798] pnp 00:04: Plug and Play ACPI device, IDs PNP0f13 PNP0f0e (active)
[ 0.105824] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.106011] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 PNP0500 (active)
[ 0.106151] pnp 00:07: [dma 2]
[ 0.106178] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
[ 0.106232] pnp 00:08: Plug and Play ACPI device, IDs PNP0003 (active)
[ 0.106256] pnp 00:09: Plug and Play ACPI device, IDs IFX0102 PNP0c31 (active)
[ 0.106302] pnp 00:0a: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.106472] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.106493] pnp 00:0c: disabling [io 0xf800-0xf81f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
[ 0.106495] pnp 00:0c: disabling [io 0xf820-0xf83f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
[ 0.106498] pnp 00:0c: disabling [io 0xf840-0xf85f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
[ 0.106500] pnp 00:0c: disabling [io 0xf860-0xf87f] because it overlaps 0000:00:1f.0 BAR 13 [io 0xf800-0xf87f]
[ 0.106529] system 00:0c: [io 0x0400-0x041f] has been reserved
[ 0.106532] system 00:0c: [io 0x0420-0x043f] has been reserved
[ 0.106534] system 00:0c: [io 0x0440-0x045f] has been reserved
[ 0.106536] system 00:0c: [io 0x0460-0x047f] has been reserved
[ 0.106539] system 00:0c: [io 0x0480-0x048f] has been reserved
[ 0.106541] system 00:0c: [io 0xfa00-0xfa3f] has been reserved
[ 0.106543] system 00:0c: [io 0xfc00-0xfc7f] has been reserved
[ 0.106546] system 00:0c: [io 0xfc80-0xfcff] has been reserved
[ 0.106548] system 00:0c: [io 0xfe00-0xfe7f] has been reserved
[ 0.106550] system 00:0c: [io 0xfe80-0xfeff] has been reserved
[ 0.106553] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.106595] system 00:0d: [io 0x04d0-0x04d1] has been reserved
[ 0.106598] system 00:0d: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.108307] system 00:0e: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.108310] system 00:0e: [mem 0x00100000-0xdfffffff] could not be reserved
[ 0.108312] system 00:0e: [mem 0x000e4000-0x000fffff] could not be reserved
[ 0.108315] system 00:0e: [mem 0xfec01000-0xfecfffff] has been reserved
[ 0.108317] system 00:0e: [mem 0xfed00400-0xfed3ffff] has been reserved
[ 0.108319] system 00:0e: [mem 0xfed45000-0xffffffff] has been reserved
[ 0.108322] system 00:0e: [mem 0xf4000000-0xf7ffffff] has been reserved
[ 0.108324] system 00:0e: [mem 0x000cea00-0x000e3fff] has been reserved
[ 0.108327] system 00:0e: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.108335] pnp: PnP ACPI: found 15 devices
[ 0.108336] ACPI: bus type PNP unregistered
[ 0.114592] pci 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 20] add_size 1000
[ 0.114595] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 20] add_size 200000
[ 0.114598] pci 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff] to [bus 20] add_size 200000
[ 0.114605] pci 0000:00:1c.1: bridge window [io 0x1000-0x0fff] to [bus 30] add_size 1000
[ 0.114607] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 30] add_size 200000
[ 0.114610] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff] to [bus 30] add_size 200000
[ 0.114620] pci 0000:00:1c.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.114622] pci 0000:00:1c.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.114624] pci 0000:00:1c.1: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.114627] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.114629] pci 0000:00:1c.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.114631] pci 0000:00:1c.1: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.114634] pci 0000:00:1c.0: BAR 14: assigned [mem 0xf8000000-0xf81fffff]
[ 0.114637] pci 0000:00:1c.0: BAR 15: assigned [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.114639] pci 0000:00:1c.1: BAR 14: assigned [mem 0xf8400000-0xf85fffff]
[ 0.114642] pci 0000:00:1c.1: BAR 15: assigned [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.114645] pci 0000:00:1c.0: BAR 13: assigned [io 0x3000-0x3fff]
[ 0.114648] pci 0000:00:1c.1: BAR 13: assigned [io 0x4000-0x4fff]
[ 0.114651] pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x20000)
[ 0.114654] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.114656] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff]
[ 0.114659] pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf2ffffff]
[ 0.114662] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.114665] pci 0000:00:1c.0: PCI bridge to [bus 20]
[ 0.114668] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
[ 0.114672] pci 0000:00:1c.0: bridge window [mem 0xf8000000-0xf81fffff]
[ 0.114675] pci 0000:00:1c.0: bridge window [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.114680] pci 0000:00:1c.1: PCI bridge to [bus 30]
[ 0.114682] pci 0000:00:1c.1: bridge window [io 0x4000-0x4fff]
[ 0.114686] pci 0000:00:1c.1: bridge window [mem 0xf8400000-0xf85fffff]
[ 0.114690] pci 0000:00:1c.1: bridge window [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.114694] pci 0000:00:1e.0: PCI bridge to [bus 07]
[ 0.114916] pci 0000:00:1e.0: setting latency timer to 64
[ 0.114919] pci_bus 0000:00: resource 4 [mem 0xf8000000-0xfebfffff]
[ 0.114921] pci_bus 0000:00: resource 5 [io 0x0000-0x0cf7]
[ 0.114923] pci_bus 0000:00: resource 6 [io 0x1000-0x2fff]
[ 0.114925] pci_bus 0000:00: resource 7 [io 0x3000-0x6fff]
[ 0.114927] pci_bus 0000:00: resource 8 [io 0x7000-0xafff]
[ 0.114929] pci_bus 0000:00: resource 9 [io 0xb000-0xffff]
[ 0.114930] pci_bus 0000:00: resource 10 [mem 0x000a0000-0x000bffff]
[ 0.114932] pci_bus 0000:00: resource 11 [mem 0xe0000000-0xf3ffffff]
[ 0.114934] pci_bus 0000:00: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.114936] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
[ 0.114938] pci_bus 0000:01: resource 1 [mem 0xf0000000-0xf2ffffff]
[ 0.114940] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.114942] pci_bus 0000:20: resource 0 [io 0x3000-0x3fff]
[ 0.114944] pci_bus 0000:20: resource 1 [mem 0xf8000000-0xf81fffff]
[ 0.114946] pci_bus 0000:20: resource 2 [mem 0xf8200000-0xf83fffff 64bit pref]
[ 0.114948] pci_bus 0000:30: resource 0 [io 0x4000-0x4fff]
[ 0.114950] pci_bus 0000:30: resource 1 [mem 0xf8400000-0xf85fffff]
[ 0.114952] pci_bus 0000:30: resource 2 [mem 0xf8600000-0xf87fffff 64bit pref]
[ 0.114954] pci_bus 0000:07: resource 4 [mem 0xf8000000-0xfebfffff]
[ 0.114956] pci_bus 0000:07: resource 5 [io 0x0000-0x0cf7]
[ 0.114957] pci_bus 0000:07: resource 6 [io 0x1000-0x2fff]
[ 0.114959] pci_bus 0000:07: resource 7 [io 0x3000-0x6fff]
[ 0.114961] pci_bus 0000:07: resource 8 [io 0x7000-0xafff]
[ 0.114963] pci_bus 0000:07: resource 9 [io 0xb000-0xffff]
[ 0.114965] pci_bus 0000:07: resource 10 [mem 0x000a0000-0x000bffff]
[ 0.114967] pci_bus 0000:07: resource 11 [mem 0xe0000000-0xf3ffffff]
[ 0.114969] pci_bus 0000:07: resource 12 [mem 0xfed40000-0xfed44fff]
[ 0.115000] NET: Registered protocol family 2
[ 0.115156] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.115303] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.115416] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.115440] TCP: reno registered
[ 0.115447] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.115468] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.115531] NET: Registered protocol family 1
[ 0.117178] pci 0000:01:00.0: Boot video device
[ 0.117181] PCI: CLS 64 bytes, default 64
[ 0.117211] Unpacking initramfs...
[ 0.154823] Freeing initrd memory: 2524k freed
[ 0.155337] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.155340] software IO TLB [mem 0xdafaf000-0xdefaf000] (64MB) mapped at [ffff8800dafaf000-ffff8800defaefff]
[ 0.155621] audit: initializing netlink socket (disabled)
[ 0.155637] type=2000 audit(1376410980.152:1): initialized
[ 0.170676] bounce pool size: 64 pages
[ 0.170680] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.171072] VFS: Disk quotas dquot_6.5.2
[ 0.171090] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.171166] msgmni has been set to 7767
[ 0.171330] alg: No test for stdrng (krng)
[ 0.171348] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.171370] io scheduler noop registered
[ 0.171372] io scheduler deadline registered
[ 0.171380] io scheduler cfq registered (default)
[ 0.171464] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.171527] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.171597] pcieport 0000:00:1c.1: irq 42 for MSI/MSI-X
[ 0.171662] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.171676] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.171677] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.171866] intel_idle: does not run on family 6 model 23
[ 0.171899] GHES: HEST is not enabled!
[ 0.171944] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.192333] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.192703] Linux agpgart interface v0.103
[ 0.192861] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
[ 0.195737] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.195742] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.195833] mousedev: PS/2 mouse device common for all mice
[ 0.195871] rtc_cmos 00:02: RTC can wake from S4
[ 0.195972] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.195993] rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.196009] cpuidle: using governor ladder
[ 0.196010] cpuidle: using governor menu
[ 0.196028] drop_monitor: Initializing network drop monitor service
[ 0.196093] TCP: cubic registered
[ 0.196115] NET: Registered protocol family 10
[ 0.196281] mip6: Mobile IPv6
[ 0.196284] NET: Registered protocol family 17
[ 0.196454] PM: Hibernation image not present or could not be loaded.
[ 0.196462] registered taskstats version 1
[ 0.196933] rtc_cmos 00:02: setting system clock to 2013-08-13 16:23:00 UTC (1376410980)
[ 0.197644] Freeing unused kernel memory: 880k freed
[ 0.197861] Write protecting the kernel read-only data: 6144k
[ 0.198852] Freeing unused kernel memory: 440k freed
[ 0.200074] Freeing unused kernel memory: 520k freed
[ 0.204899] udevd[56]: starting version 175
[ 0.231271] SCSI subsystem initialized
[ 0.242449] ACPI: bus type ATA registered
[ 0.246988] libata version 3.00 loaded.
[ 0.247289] ata_piix 0000:00:1f.2: version 2.13
[ 0.247427] ata_piix 0000:00:1f.2: MAP [
[ 0.247428] P0 -- P1 -- ]
[ 0.247459] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.258899] scsi0 : ata_piix
[ 0.261017] scsi1 : ata_piix
[ 0.261083] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2200 irq 14
[ 0.261086] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2208 irq 15
[ 0.261205] ata_piix 0000:00:1f.5: MAP [
[ 0.261207] P0 -- P1 -- ]
[ 0.416030] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 0.416277] scsi2 : ata_piix
[ 0.416321] scsi3 : ata_piix
[ 0.416357] ata3: SATA max UDMA/133 cmd 0x2250 ctl 0x2268 bmdma 0x2220 irq 18
[ 0.416359] ata4: SATA max UDMA/133 cmd 0x2258 ctl 0x226c bmdma 0x2228 irq 18
[ 0.736048] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 0.736147] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.744114] ata2.00: ATAPI: TSSTcorp CDDVDW TS-H653Q, HC01, max UDMA/100
[ 0.746699] ata3: SATA link down (SStatus 0 SControl 300)
[ 0.746819] ata1.00: ATA-8: WDC WD1600AAJS-60M0A0, 02.03E02, max UDMA/100
[ 0.746821] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 0.757241] ata4: SATA link down (SStatus 0 SControl 300)
[ 0.760125] ata1.00: configured for UDMA/100
[ 0.760238] scsi 0:0:0:0: Direct-Access ATA WDC WD1600AAJS-6 02.0 PQ: 0 ANSI: 5
[ 0.764127] ata2.00: configured for UDMA/100
[ 0.765065] scsi 1:0:0:0: CD-ROM TSSTcorp CDDVDW TS-H653Q HC01 PQ: 0 ANSI: 5
[ 0.767982] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 0.768034] sd 0:0:0:0: [sda] Write Protect is off
[ 0.768036] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.768054] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.787321] sda: sda1 sda2 sda3 sda4
[ 0.787683] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.124469] PM: Starting manual resume from disk
[ 1.124472] PM: Hibernation image partition 8:3 present
[ 1.124473] PM: Looking for hibernation image.
[ 1.124657] PM: Image not found (code -22)
[ 1.124659] PM: Hibernation image not present or could not be loaded.
[ 1.152014] tsc: Refined TSC clocksource calibration: 3158.749 MHz
[ 1.152019] Switching to clocksource tsc
[ 1.161249] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 2.630739] udevd[346]: starting version 175
[ 3.555677] microcode: CPU0 sig=0x1067a, pf=0x1, revision=0xa0b
[ 3.589429] platform microcode: firmware: agent loaded intel-ucode/06-17-0a into memory
[ 3.589458] microcode: CPU1 sig=0x1067a, pf=0x1, revision=0xa0b
[ 3.589480] platform microcode: firmware: agent loaded intel-ucode/06-17-0a into memory
[ 3.589548] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 3.648518] ACPI: bus type USB registered
[ 3.648543] usbcore: registered new interface driver usbfs
[ 3.648553] usbcore: registered new interface driver hub
[ 3.648615] usbcore: registered new device driver usb
[ 3.660132] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.785053] wmi: Mapper loaded
[ 3.853038] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 3.853045] ACPI: Power Button [PBTN]
[ 3.853086] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 3.853088] ACPI: Power Button [PWRF]
[ 3.882870] mei 0000:00:03.0: setting latency timer to 64
[ 3.882899] mei 0000:00:03.0: irq 43 for MSI/MSI-X
[ 3.906177] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 3.909930] FDC 0 is a post-1991 82077
[ 3.994685] pps_core: LinuxPPS API ver. 1 registered
[ 3.994686] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 4.002332] PTP clock support registered
[ 4.180891] input: HP WMI hotkeys as /devices/virtual/input/input3
[ 4.182949] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.185841] ehci-pci: EHCI PCI platform driver
[ 4.186402] tpm_tis 00:09: 1.2 TPM (device-id 0xB, rev-id 16)
[ 4.196682] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 4.196685] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 4.196691] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 4.196726] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00002120
[ 4.196756] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.196758] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.196760] usb usb1: Product: UHCI Host Controller
[ 4.196761] usb usb1: Manufacturer: Linux 3.9-1-amd64 uhci_hcd
[ 4.196763] usb usb1: SerialNumber: 0000:00:1a.0
[ 4.196843] hub 1-0:1.0: USB hub found
[ 4.196846] hub 1-0:1.0: 2 ports detected
[ 4.204397] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 4.204401] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 4.204406] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2
[ 4.204436] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00002140
[ 4.204463] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.204465] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.204467] usb usb2: Product: UHCI Host Controller
[ 4.204468] usb usb2: Manufacturer: Linux 3.9-1-amd64 uhci_hcd
[ 4.204470] usb usb2: SerialNumber: 0000:00:1a.1
[ 4.204620] hub 2-0:1.0: USB hub found
[ 4.204624] hub 2-0:1.0: 2 ports detected
[ 4.204783] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 4.204786] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 4.204793] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3
[ 4.204821] uhci_hcd 0000:00:1a.2: irq 22, io base 0x00002160
[ 4.204845] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.204847] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.204849] usb usb3: Product: UHCI Host Controller
[ 4.204851] usb usb3: Manufacturer: Linux 3.9-1-amd64 uhci_hcd
[ 4.204852] usb usb3: SerialNumber: 0000:00:1a.2
[ 4.204933] hub 3-0:1.0: USB hub found
[ 4.204937] hub 3-0:1.0: 2 ports detected
[ 4.205095] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 4.205098] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 4.205102] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4
[ 4.205122] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00002180
[ 4.205146] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.205148] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.205150] usb usb4: Product: UHCI Host Controller
[ 4.205151] usb usb4: Manufacturer: Linux 3.9-1-amd64 uhci_hcd
[ 4.205153] usb usb4: SerialNumber: 0000:00:1d.0
[ 4.205230] hub 4-0:1.0: USB hub found
[ 4.205233] hub 4-0:1.0: 2 ports detected
[ 4.205389] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 4.205392] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 4.205397] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 4.205416] uhci_hcd 0000:00:1d.1: irq 21, io base 0x000021a0
[ 4.205440] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.205442] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.205444] usb usb5: Product: UHCI Host Controller
[ 4.205445] usb usb5: Manufacturer: Linux 3.9-1-amd64 uhci_hcd
[ 4.205447] usb usb5: SerialNumber: 0000:00:1d.1
[ 4.205529] hub 5-0:1.0: USB hub found
[ 4.205533] hub 5-0:1.0: 2 ports detected
[ 4.205689] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 4.205691] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 4.205697] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 4.205716] uhci_hcd 0000:00:1d.2: irq 22, io base 0x000021c0
[ 4.205740] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.205742] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.205744] usb usb6: Product: UHCI Host Controller
[ 4.205746] usb usb6: Manufacturer: Linux 3.9-1-amd64 uhci_hcd
[ 4.205747] usb usb6: SerialNumber: 0000:00:1d.2
[ 4.205822] hub 6-0:1.0: USB hub found
[ 4.205826] hub 6-0:1.0: 2 ports detected
[ 4.206710] ehci-pci 0000:00:1a.7: setting latency timer to 64
[ 4.206713] ehci-pci 0000:00:1a.7: EHCI Host Controller
[ 4.206717] ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 7
[ 4.206729] ehci-pci 0000:00:1a.7: debug port 1
[ 4.210624] ehci-pci 0000:00:1a.7: cache line size of 64 is not supported
[ 4.210630] ehci-pci 0000:00:1a.7: irq 22, io mem 0xf3025000
[ 4.220017] ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 4.220058] usb usb7: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.220062] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.220065] usb usb7: Product: EHCI Host Controller
[ 4.220067] usb usb7: Manufacturer: Linux 3.9-1-amd64 ehci_hcd
[ 4.220070] usb usb7: SerialNumber: 0000:00:1a.7
[ 4.220204] hub 7-0:1.0: USB hub found
[ 4.220208] hub 7-0:1.0: 6 ports detected
[ 4.220429] ehci-pci 0000:00:1d.7: setting latency timer to 64
[ 4.220432] ehci-pci 0000:00:1d.7: EHCI Host Controller
[ 4.220437] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 8
[ 4.220448] ehci-pci 0000:00:1d.7: debug port 1
[ 4.224356] ehci-pci 0000:00:1d.7: cache line size of 64 is not supported
[ 4.224362] ehci-pci 0000:00:1d.7: irq 20, io mem 0xf3025400
[ 4.236011] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 4.236049] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.236053] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.236056] usb usb8: Product: EHCI Host Controller
[ 4.236059] usb usb8: Manufacturer: Linux 3.9-1-amd64 ehci_hcd
[ 4.236061] usb usb8: SerialNumber: 0000:00:1d.7
[ 4.236188] hub 8-0:1.0: USB hub found
[ 4.236194] hub 8-0:1.0: 6 ports detected
[ 4.301745] e1000e: Intel(R) PRO/1000 Network Driver - 2.2.14-k
[ 4.301748] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 4.301891] e1000e 0000:00:19.0: setting latency timer to 64
[ 4.301932] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 4.301957] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 4.316064] tpm_tis 00:09: Adjusting TPM timeout parameters.
[ 4.362099] iTCO_vendor_support: vendor-support=0
[ 4.378689] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 4.378711] iTCO_wdt: Found a ICH9 TCO device (Version=2, TCOBASE=0xf860)
[ 4.378755] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 4.392046] ACPI: Requesting acpi_cpufreq
[ 4.392172] tsc: Marking TSC unstable due to TSC halts in idle
[ 4.392180] ACPI: acpi_idle registered with cpuidle
[ 4.393055] Switching to clocksource hpet
[ 4.464644] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 4.464648] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 4.464788] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.483189] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.483217] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.597955] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:23:7d:46:35:93
[ 4.597958] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 4.597976] e1000e 0000:00:19.0 eth0: MAC: 7, PHY: 6, PBA No: 1042FF-0FF
[ 4.600600] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 4.714618] [drm] Initialized drm 1.1.0 20060810
[ 4.772038] usb 1-1: new low-speed USB device number 2 using uhci_hcd
[ 4.928405] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x086f00a2
[ 4.928409] nouveau [ DEVICE][0000:01:00.0] Chipset: G86 (NV86)
[ 4.928410] nouveau [ DEVICE][0000:01:00.0] Family : NV50
[ 4.929042] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
[ 4.948057] usb 1-1: New USB device found, idVendor=03f0, idProduct=0024
[ 4.948059] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.948061] usb 1-1: Product: HP Basic USB Keyboard
[ 4.948063] usb 1-1: Manufacturer: CHICONY
[ 4.970592] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
[ 4.970594] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
[ 4.970737] nouveau [ VBIOS][0000:01:00.0] BIT signature found
[ 4.970740] nouveau [ VBIOS][0000:01:00.0] version 60.86.63.00.19
[ 4.990746] nouveau [ PFB][0000:01:00.0] RAM type: DDR2
[ 4.990748] nouveau [ PFB][0000:01:00.0] RAM size: 256 MiB
[ 4.990750] nouveau [ PFB][0000:01:00.0] ZCOMP: 646 tags
[ 5.062695] hda_codec: AD1884: BIOS auto-probing.
[ 5.064787] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input4
[ 5.068347] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 5.068433] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 5.068516] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 5.068600] input: HDA Intel Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 5.120057] tpm_tis 00:09: TPM is disabled/deactivated (0x7)
[ 5.188020] usb 5-2: new low-speed USB device number 2 using uhci_hcd
[ 5.338488] hidraw: raw HID events driver (C) Jiri Kosina
[ 5.364044] usb 5-2: New USB device found, idVendor=046d, idProduct=c03d
[ 5.364047] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.364049] usb 5-2: Product: USB-PS/2 Optical Mouse
[ 5.364050] usb 5-2: Manufacturer: Logitech
[ 5.380640] usbcore: registered new interface driver usbhid
[ 5.380642] usbhid: USB HID core driver
[ 5.726295] input: CHICONY HP Basic USB Keyboard as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.0/input/input9
[ 5.727087] hid-generic 0003:03F0:0024.0001: input,hidraw0: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:1a.0-1/input0
[ 5.727219] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb5/5-2/5-2:1.0/input/input10
[ 5.727358] hid-generic 0003:046D:C03D.0002: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-2/input0
[ 9.029822] nouveau [ PTHERM][0000:01:00.0] FAN control: PWM
[ 9.029834] nouveau [ PTHERM][0000:01:00.0] fan management: disabled
[ 9.029839] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
[ 9.029844] nouveau [ PTHERM][0000:01:00.0] Programmed thresholds [ 90(3), 95(3), 115(2), 135(5) ]
[ 9.029963] [TTM] Zone kernel: Available graphics memory: 1989348 kiB
[ 9.029966] [TTM] Initializing pool allocator
[ 9.029972] [TTM] Initializing DMA pool allocator
[ 9.029989] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[ 9.029992] nouveau [ DRM] VRAM: 256 MiB
[ 9.029994] nouveau [ DRM] GART: 512 MiB
[ 9.029999] nouveau [ DRM] TMDS table version 2.0
[ 9.030002] nouveau [ DRM] DCB version 4.0
[ 9.030005] nouveau [ DRM] DCB outp 00: 02011300 00000028
[ 9.030008] nouveau [ DRM] DCB outp 01: 01011302 00000010
[ 9.030011] nouveau [ DRM] DCB outp 02: 01000310 00000028
[ 9.030013] nouveau [ DRM] DCB outp 03: 02000312 00000010
[ 9.030016] nouveau [ DRM] DCB conn 00: 2030
[ 9.030019] nouveau [ DRM] DCB conn 01: 1130
[ 9.030064] nouveau E[ PTHERM][0000:01:00.0] unhandled intr 0x000001e1
[ 9.037943] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 9.037945] [drm] No driver support for vblank timestamp query.
[ 9.038047] nouveau [ DRM] 2 available performance level(s)
[ 9.038051] nouveau [ DRM] 0: core 208MHz shader 416MHz memory 100MHz fanspeed 100%
[ 9.038053] nouveau [ DRM] 1: core 459MHz shader 918MHz memory 400MHz fanspeed 100%
[ 9.038056] nouveau [ DRM] c: core 459MHz shader 918MHz memory 399MHz fanspeed 100%
[ 9.045163] nouveau [ DRM] MM: using CRYPT for buffer copies
[ 9.088535] nouveau [ DRM] allocated 1920x1080 fb: 0x60000, bo ffff8801164d0400
[ 9.088591] fbcon: nouveaufb (fb0) is primary device
[ 9.147498] Console: switching to colour frame buffer device 240x67
[ 9.150317] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
[ 9.150319] nouveau 0000:01:00.0: registered panic notifier
[ 9.150330] [drm] Initialized nouveau 1.1.0 20120801 for 0000:01:00.0 on minor 0
[ 9.822075] Adding 3906556k swap on /dev/sda3. Priority:-1 extents:1 across:3906556k
[ 9.851253] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 10.234639] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 11.067194] fuse init (API version 7.21)
[ 11.102182] loop: module loaded
[ 11.426272] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 11.502837] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: user_xattr
[ 12.015558] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.060252] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 14.201435] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input11
[ 15.846761] lp: driver loaded but no devices found
[ 16.000528] ppdev: user-space parallel port driver
[ 19.372265] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 19.476087] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 19.476198] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.200501] e1000e 0000:00:19.0: setting latency timer to 64
[ 22.200540] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[ 22.333796] e1000e 0000:00:19.0 eth0: MAC Wakeup cause - Link Status Change
[ 23.944858] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[ 23.944966] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO
[ 23.944994] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Reply to: