Bug#716827: linux-image-3.9-1-amd64: Not detected laptop webcam with Jessie (ver: 3.9.8-1) although Wheezy (ver: 3.2.35-2) did it
Package: src:linux
Version: 3.9.8-1
Followup-For: Bug #716827
Dear Maintainer,
The bug can be closed.
* What exactly did you do (or not do) that was effective (or
ineffective)?
The reported camera had been deactivated by hardware by mean of a
rather bizarre key combination.
After realizing that, I activated it. Now the camera is working
without any problem.
Sorry for the annoyance. I really didn't know that it is possible to
change the camera state in this way.
robert
-- Package-specific info:
** Version:
Linux version 3.9-1-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.3 (Debian 4.7.3-5) ) #1 SMP Debian 3.9.8-1
** Command line:
BOOT_IMAGE=/vmlinuz-3.9-1-amd64 root=/dev/mapper/nyxVG-root ro quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 17.132399] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20130117/utaddress-251)
[ 17.132409] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 17.132413] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 17.132670] ACPI Warning: 0x000000000000f040-0x000000000000f05f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20130117/utaddress-251)
[ 17.132698] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 17.133041] snd_hda_intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[ 17.140257] iTCO_vendor_support: vendor-support=0
[ 17.140857] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 17.140901] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
[ 17.140993] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 17.153707] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 17.153863] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 17.154003] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 17.173250] psmouse serio2: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000, board id: 3655, fw id: 582762
[ 17.208092] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input10
[ 17.460063] ACPI: AC Adapter [AC] (off-line)
[ 17.461015] ACPI Error: [_T_0] Namespace lookup failure, AE_ALREADY_EXISTS (20130117/dswload2-330)
[ 17.461027] ACPI Exception: AE_ALREADY_EXISTS, During name lookup/catalog (20130117/psobject-222)
[ 17.461033] ACPI Error: Method parse/execution failed [\_SB_.AC__.ADJP] (Node ffff88021549dce0), AE_ALREADY_EXISTS (20130117/psparse-537)
[ 17.461043] ACPI Error: Method parse/execution failed [\_SB_.AC__._PSR] (Node ffff88021549dd30), AE_ALREADY_EXISTS (20130117/psparse-537)
[ 17.461056] ACPI Exception: AE_ALREADY_EXISTS, Error reading AC Adapter state (20130117/ac-122)
[ 17.461287] ACPI Error: [_T_0] Namespace lookup failure, AE_ALREADY_EXISTS (20130117/dswload2-330)
[ 17.461299] ACPI Exception: AE_ALREADY_EXISTS, During name lookup/catalog (20130117/psobject-222)
[ 17.461304] ACPI Error: Method parse/execution failed [\_SB_.AC__.ADJP] (Node ffff88021549dce0), AE_ALREADY_EXISTS (20130117/psparse-537)
[ 17.461314] ACPI Error: Method parse/execution failed [\_SB_.AC__._PSR] (Node ffff88021549dd30), AE_ALREADY_EXISTS (20130117/psparse-537)
[ 17.461325] ACPI Exception: AE_ALREADY_EXISTS, Error reading AC Adapter state (20130117/ac-122)
[ 17.461878] ACPI Error: [_T_0] Namespace lookup failure, AE_ALREADY_EXISTS (20130117/dswload2-330)
[ 17.461906] ACPI Exception: AE_ALREADY_EXISTS, During name lookup/catalog (20130117/psobject-222)
[ 17.461911] ACPI Error: Method parse/execution failed [\_SB_.AC__.ADJP] (Node ffff88021549dce0), AE_ALREADY_EXISTS (20130117/psparse-537)
[ 17.461919] ACPI Error: Method parse/execution failed [\_SB_.AC__._PSR] (Node ffff88021549dd30), AE_ALREADY_EXISTS (20130117/psparse-537)
[ 17.461933] ACPI Exception: AE_ALREADY_EXISTS, Error reading AC Adapter state (20130117/ac-122)
[ 17.467192] ACPI: Marking method ADJP as Serialized because of AE_ALREADY_EXISTS error
[ 17.468112] ACPI: Marking method _PSR as Serialized because of AE_ALREADY_EXISTS error
[ 17.775074] [drm] Enabling RC6 states: RC6 on, RC6p on, RC6pp off
[ 17.975784] ACPI: Battery Slot [BAT0] (battery present)
[ 17.976227] wmi: Mapper loaded
[ 18.315303] Adding 8785916k swap on /dev/mapper/nyxVG-swap. Priority:-1 extents:1 across:8785916k SS
[ 18.340752] EXT4-fs (dm-1): re-mounted. Opts: (null)
[ 18.442669] EXT4-fs (dm-1): re-mounted. Opts: errors=remount-ro
[ 18.712810] fuse init (API version 7.21)
[ 18.725937] loop: module loaded
[ 19.039358] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[ 19.472002] RPC: Registered named UNIX socket transport module.
[ 19.472008] RPC: Registered udp transport module.
[ 19.472010] RPC: Registered tcp transport module.
[ 19.472013] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 19.477782] FS-Cache: Loaded
[ 19.478573] Key type dns_resolver registered
[ 19.486518] FS-Cache: Netfs 'nfs' registered for caching
[ 19.496221] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 19.981988] vboxdrv: Found 8 processor cores.
[ 19.982282] vboxdrv: fAsync=0 offMin=0x370 offMax=0x2b32
[ 19.982428] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 19.982433] vboxdrv: Successfully loaded version 4.2.16_Debian (interface 0x001a0005).
[ 20.094951] vboxpci: IOMMU not found (not registered)
[ 20.141554] Bluetooth: RFCOMM TTY layer initialized
[ 20.141575] Bluetooth: RFCOMM socket layer initialized
[ 20.141579] Bluetooth: RFCOMM ver 1.11
[ 20.146015] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 20.146022] Bluetooth: BNEP filters: protocol multicast
[ 20.146038] Bluetooth: BNEP socket layer initialized
[ 20.221992] lp: driver loaded but no devices found
[ 20.228661] ppdev: user-space parallel port driver
[ 20.731698] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 20.752609] r8169 0000:03:00.2: firmware: agent loaded rtl_nic/rtl8411-1.fw into memory
[ 20.822261] r8169 0000:03:00.2 eth0: link down
[ 20.822302] r8169 0000:03:00.2 eth0: link down
[ 20.822344] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 20.947321] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input11
[ 22.480627] r8169 0000:03:00.2 eth0: link up
[ 22.480641] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 36.659044] wlan0: authenticate with 00:0b:86:21:ea:a0
[ 36.690131] wlan0: send auth to 00:0b:86:21:ea:a0 (try 1/3)
[ 36.692427] wlan0: authenticated
[ 36.692594] rtl8723ae 0000:02:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 36.692600] rtl8723ae 0000:02:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 36.693860] wlan0: associate with 00:0b:86:21:ea:a0 (try 1/3)
[ 36.703882] wlan0: RX AssocResp from 00:0b:86:21:ea:a0 (capab=0x11 status=0 aid=1)
[ 36.703987] wlan0: associated
[ 36.704024] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 45.716098] wlan0: deauthenticating from 00:0b:86:21:ea:a0 by local choice (reason=3)
[ 45.740388] cfg80211: Calling CRDA to update world regulatory domain
[ 45.757023] cfg80211: World regulatory domain updated:
[ 45.757039] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 45.757054] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 45.757065] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 45.757081] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 45.757091] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 45.757099] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 91.457926] usb 3-1.1: new high-speed USB device number 3 using ehci-pci
[ 91.639796] usb 3-1.1: New USB device found, idVendor=5986, idProduct=0400
[ 91.639804] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 91.639809] usb 3-1.1: Product: BisonCam, NB Pro
[ 91.639812] usb 3-1.1: Manufacturer: Bison
[ 91.692980] media: Linux media interface: v0.10
[ 91.697012] Linux video capture interface: v2.00
[ 91.703384] uvcvideo: Found UVC 1.00 device BisonCam, NB Pro (5986:0400)
[ 91.708571] input: BisonCam, NB Pro as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.1/3-1.1:1.0/input/input12
[ 91.708734] usbcore: registered new interface driver uvcvideo
[ 91.708738] USB Video Class driver (1.1.1)
** Model information
sys_vendor: CLEVO CO.
product_name: W55xEU
product_version: Not Applicable
chassis_vendor: No Enclosure
chassis_version: N/A
bios_vendor: American Megatrends Inc.
bios_version: 4.6.5
board_vendor: CLEVO CO.
board_name: W55xEU
board_version: D02
** Loaded modules:
uvcvideo
videobuf2_vmalloc
videobuf2_memops
videobuf2_core
videodev
media
parport_pc
ppdev
lp
parport
bnep
rfcomm
pci_stub
vboxpci(O)
cpufreq_stats
cpufreq_userspace
cpufreq_powersave
cpufreq_conservative
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
binfmt_misc
uinput
nfsd
auth_rpcgss
nfs_acl
nfs
lockd
dns_resolver
fscache
sunrpc
ext2
loop
fuse
joydev
snd_hda_codec_hdmi
snd_hda_codec_via
iTCO_wdt
iTCO_vendor_support
arc4
btusb
bluetooth
rtl8723ae
rtlwifi
mac80211
coretemp
cfg80211
kvm_intel
rfkill
snd_hda_intel
kvm
snd_hda_codec
snd_hwdep
snd_pcm
snd_page_alloc
snd_seq
microcode
snd_seq_device
wmi
snd_timer
rtsx_pci_ms
pcspkr
i2c_i801
psmouse
snd
lpc_ich
memstick
evdev
serio_raw
i915
acpi_cpufreq
drm_kms_helper
drm
mperf
i2c_algo_bit
i2c_core
soundcore
battery
video
mei
ac
processor
button
ext4
crc16
jbd2
mbcache
dm_crypt
dm_mod
sg
sr_mod
sd_mod
cdrom
crc_t10dif
rtsx_pci_sdmmc
mmc_core
crc32c_intel
r8169
mii
rtsx_pci
mfd_core
ghash_clmulni_intel
aesni_intel
aes_x86_64
thermal
thermal_sys
ablk_helper
cryptd
xts
lrw
ahci
gf128mul
libahci
ehci_pci
libata
xhci_hcd
ehci_hcd
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09)
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f6400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 40
Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f7d1b000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7d18000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at f7d10000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 [8086:1e14] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7c00000-f7cfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 4 [8086:1e16] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f7200000-f7bfffff
Prefetchable memory behind bridge: 00000000f0a00000-00000000f13fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 5 [8086:1e18] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=06, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f6800000-f71fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f09fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7d17000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge [0601]: Intel Corporation HM77 Express Chipset LPC Controller [8086:1e57] (rev 04)
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 43
Region 0: I/O ports at f0b0 [size=8]
Region 1: I/O ports at f0a0 [size=4]
Region 2: I/O ports at f090 [size=8]
Region 3: I/O ports at f080 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7d16000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
Subsystem: CLEVO/KAPOK Computer Device [1558:0550]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7d15000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8723AE PCIe Wireless Network Adapter [10ec:8723]
Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:0726]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at e000 [size=256]
Region 2: Memory at f7c00000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: rtl8723ae
03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device [10ec:5289] (rev 01)
Subsystem: CLEVO/KAPOK Computer Device [1558:0540]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 41
Region 0: Memory at f7200000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: rtsx_pci
03:00.2 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 0a)
Subsystem: CLEVO/KAPOK Computer Device [1558:0540]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 42
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at f0a04000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f0a00000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
** USB devices:
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 5986:0400 Acer, Inc
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 0bda:8723 Realtek Semiconductor Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.9-1-amd64 (SMP w/8 CPU cores)
Locale: LANG=ca_ES.UTF-8, LC_CTYPE=ca_ES.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.9-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.50
ii initramfs-tools [linux-initramfs-tool] 0.113
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.9-1-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.9-1-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u1
pn linux-doc-3.9 <none>
Versions of packages linux-image-3.9-1-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.39
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.9-1-amd64/postinst/ignoring-ramdisk:
linux-image-3.9-1-amd64/postinst/missing-firmware-3.9-1-amd64:
linux-image-3.9-1-amd64/prerm/removing-running-kernel-3.9-1-amd64: true
linux-image-3.9-1-amd64/postinst/depmod-error-initrd-3.9-1-amd64: false
Reply to: