--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.26-1-vserver-686: Problem with Vserver CPU scheduler, vserver never hold (hold-ticks always 0)
- From: Mario Abajo Duran <marioabajo@gmail.com>
- Date: Sun, 11 Jan 2009 02:04:58 +0100
- Message-id: <20090111010458.4483.93565.reportbug@beta.homelinux.org>
Package: linux-image-2.6.26-1-vserver-686
Version: 2.6.26-12
Severity: normal
Hi, i was trying out the token bucket directly with lenny but seems that no configuration
makes the guest vserver get hold.
The status and the configuration of the scheduler can be shown here:
beta:/etc/vservers/amule# cat /proc/virtual/40001/sched
FillRate: 1,1
Interval: 1,8
TokensMin: 750
TokensMax: 2988
PrioBias: 0
cpu 0: 2 7 0 0 0 RI 1 750 2988 1/1 1/8 0 0
cpu 1: 62829 22 0 0 0 RI 1 750 2988 1/1 1/8 0 0
The guest was running the "burnMMX" application for some time consumming 100% of one of
the two cpu's.
The flags of the vserver are as follows:
beta:/etc/vservers/amule# cat flags
sched_hard
virt_mem
virt_uptime
virt_cpu
virt_load
virt_time
beta:/etc/vservers/amule# cat /proc/virtual/40001/status
UseCnt: 5
Tasks: 2
Flags: 00000016021f0110
BCaps: 00000000000004ff
CCaps: 0000000000000101
Spaces: 1c020200
I hope it wont be a configuration problem, after reading quite a few documentation from
linux-vserver.org and googling for examples, configurations and similar cases like this
i reached the conclusion that maybe a bug.
Thanks in advance :)
-- Package-specific info:
** Version:
Linux version 2.6.26-1-vserver-686 (Debian 2.6.26-12) (waldi@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-24)) #1 SMP Mon Dec 15 21:11:05 UTC 2008
** Command line:
root=/dev/mapper/system-root ro quiet
** Not tainted
** Kernel log:
[ 3.536428] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.536437] usb usb1: Product: UHCI Host Controller
[ 3.536444] usb usb1: Manufacturer: Linux 2.6.26-1-vserver-686 uhci_hcd
[ 3.536452] usb usb1: SerialNumber: 0000:00:07.2
[ 3.536415] ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 3.536415] uhci_hcd 0000:00:07.3: VIA VLink IRQ fixup, from 9 to 11
[ 3.536415] uhci_hcd 0000:00:07.3: UHCI Host Controller
[ 3.536415] uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
[ 3.536415] uhci_hcd 0000:00:07.3: irq 11, io base 0x0000d000
[ 3.536588] usb usb2: configuration #1 chosen from 1 choice
[ 3.536685] hub 2-0:1.0: USB hub found
[ 3.536709] hub 2-0:1.0: 2 ports detected
[ 3.641989] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.642003] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.642012] usb usb2: Product: UHCI Host Controller
[ 3.642020] usb usb2: Manufacturer: Linux 2.6.26-1-vserver-686 uhci_hcd
[ 3.642027] usb usb2: SerialNumber: 0000:00:07.3
[ 3.648811] VP_IDE: IDE controller (0x1106:0x0571 rev 0x06) at PCI slot 0000:00:07.1
[ 3.648811] VP_IDE: not 100% native mode: will probe irqs later
[ 3.648885] VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
[ 3.648910] ide0: BM-DMA at 0xffa0-0xffa7
[ 3.648931] ide1: BM-DMA at 0xffa8-0xffaf
[ 3.648947] Probing IDE interface ide0...
[ 3.832749] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 3.955466] FDC 0 is a post-1991 82077
[ 4.070868] hda: Maxtor 6Y160P0, ATA DISK drive
[ 4.743265] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 4.743407] hda: UDMA/100 mode selected
[ 4.743529] Probing IDE interface ide1...
[ 5.306238] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.306238] ide1 at 0x170-0x177,0x376 on irq 15
[ 5.351274] 8139cp 0000:00:0a.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[ 5.351324] 8139cp 0000:00:0a.0: Try the "8139too" driver instead.
[ 5.352029] No dock devices found.
[ 5.361397] 8139too Fast Ethernet driver 0.9.28
[ 5.361397] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 5.363631] eth0: RealTek RTL8139 at 0xc800, 00:c0:26:a0:86:d3, IRQ 18
[ 5.363641] eth0: Identified 8139 chip type 'RTL-8139B'
[ 5.401184] SCSI subsystem initialized
[ 5.449184] libata version 3.00 loaded.
[ 5.502478] hda: max request size: 512KiB
[ 5.503734] hda: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63
[ 5.503907] hda: cache flushes supported
[ 5.504060] hda: hda1 hda2
[ 5.873806] device-mapper: uevent: version 1.0.3
[ 5.873806] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 6.288345] PM: Starting manual resume from disk
[ 6.334167] SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
[ 6.338396] SGI XFS Quota Management subsystem
[ 6.342396] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 6.346396] XFS mounting filesystem dm-0
[ 6.737953] Ending clean XFS mount for filesystem: dm-0
[ 8.410035] udevd version 125 started
[ 9.686094] Linux agpgart interface v0.103
[ 9.700792] agpgart: Detected VIA Apollo Pro 133 chipset
[ 9.701900] agpgart: AGP aperture is 4M @ 0xe0000000
[ 9.922461] parport_pc: VIA 686A/8231 detected
[ 9.922471] parport_pc: probing current configuration
[ 9.922494] parport_pc: Current parallel port base: 0x378
[ 9.922574] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 9.936402] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 9.947440] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 10.009694] parport_pc: VIA parallel port: io=0x378, irq=7
[ 11.283817] input: Power Button (FF) as /class/input/input1
[ 11.301548] input: PC Speaker as /class/input/input2
[ 11.358584] ACPI: Power Button (FF) [PWRF]
[ 11.358803] input: Power Button (CM) as /class/input/input3
[ 11.410993] ACPI: Power Button (CM) [PWRB]
[ 11.411243] input: Sleep Button (CM) as /class/input/input4
[ 11.460056] ACPI: Sleep Button (CM) [SLPB]
[ 11.461127] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 11.461146] ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[ 11.461311] PCI: Setting latency timer of device 0000:00:07.5 to 64
[ 11.597899] Error: Driver 'pcspkr' is already registered, aborting...
[ 11.886060] input: ImExPS/2 Generic Explorer Mouse as /class/input/input5
[ 11.994661] Error: Driver 'pcspkr' is already registered, aborting...
[ 13.597622] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 14.419036] loop: module loaded
[ 16.416902] kjournald starting. Commit interval 5 seconds
[ 16.416902] EXT3 FS on hda1, internal journal
[ 16.416902] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.430927] Filesystem "dm-1": Disabling barriers, not supported by the underlying device
[ 16.430927] XFS mounting filesystem dm-1
[ 16.684350] Ending clean XFS mount for filesystem: dm-1
[ 16.716344] Filesystem "dm-4": Disabling barriers, not supported by the underlying device
[ 16.724344] XFS mounting filesystem dm-4
[ 17.109572] Ending clean XFS mount for filesystem: dm-4
[ 17.124584] Filesystem "dm-2": Disabling barriers, not supported by the underlying device
[ 17.124584] XFS mounting filesystem dm-2
[ 17.415862] Ending clean XFS mount for filesystem: dm-2
[ 17.476325] Adding 524280k swap on /dev/mapper/system-swap. Priority:-1 extents:1 across:524280k
[ 18.711190] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 30.433714] eth0: no IPv6 routers present
[ 7331.560179] Not cloning cgroup for unused subsystem ns
[ 7331.997868] warning: `vserver-info' uses deprecated v2 capabilities in a way that may be insecure.
[ 7332.459325] Filesystem "dm-5": Disabling barriers, not supported by the underlying device
[ 7332.475168] XFS mounting filesystem dm-5
[ 7332.637384] Ending clean XFS mount for filesystem: dm-5
[ 7333.048449] Not cloning cgroup for unused subsystem ns
[12619.102872] Not cloning cgroup for unused subsystem ns
** Loaded modules:
Module Size Used by
ext3 108232 1
jbd 39444 1 ext3
mbcache 7108 1 ext3
lm80 11504 0
loop 12908 0
psmouse 32336 0
snd_via82xx 20664 0
gameport 10700 1 snd_via82xx
snd_ac97_codec 88484 1 snd_via82xx
snd_pcsp 8576 0
button 6096 0
ac97_bus 1728 1 snd_ac97_codec
serio_raw 4740 0
via686a 11948 0
snd_pcm 62596 3 snd_via82xx,snd_ac97_codec,snd_pcsp
snd_timer 17800 1 snd_pcm
snd_page_alloc 7816 2 snd_via82xx,snd_pcm
snd_mpu401_uart 6368 1 snd_via82xx
snd_rawmidi 18496 1 snd_mpu401_uart
snd_seq_device 6380 1 snd_rawmidi
snd 45604 8 snd_via82xx,snd_ac97_codec,snd_pcsp,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
i2c_viapro 6836 0
soundcore 6368 1 snd
i2c_core 19828 2 lm80,i2c_viapro
shpchp 25528 0
pci_hotplug 23460 1 shpchp
parport_pc 22500 0
parport 30988 1 parport_pc
via_agp 7744 1
agpgart 28776 1 via_agp
evdev 8000 0
xfs 459672 5
dm_mirror 15104 0
dm_log 8452 1 dm_mirror
dm_snapshot 14340 0
dm_mod 46600 16 dm_mirror,dm_log,dm_snapshot
ide_disk 10496 3
ata_generic 4676 0
libata 140384 1 ata_generic
scsi_mod 129356 1 libata
8139too 20320 0
dock 8304 1 libata
floppy 47716 0
8139cp 16800 0
mii 4896 2 8139too,8139cp
via82cxxx 6948 0 [permanent]
ide_pci_generic 3908 0 [permanent]
ide_core 96168 3 ide_disk,via82cxxx,ide_pci_generic
uhci_hcd 18672 0
usbcore 118192 2 uhci_hcd
thermal 15228 0
processor 32576 1 thermal
fan 4164 0
thermal_sys 10856 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] [1106:0691] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 16
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=4M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: agpgart-via
Kernel modules: via-agp
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] [1106:8598] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00008000-00009fff
Memory behind bridge: dde00000-dfefffff
Prefetchable memory behind bridge: ddc00000-ddcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: shpchp
00:07.0 ISA bridge [0601]: VIA Technologies, Inc. VT82C686 [Apollo Super South] [1106:0686] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge [1106:0686]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: parport_pc
Kernel modules: parport_pc
00:07.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at ffa0 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: VIA_IDE
Kernel modules: via82cxxx
00:07.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1a) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at cc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:07.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1a) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:07.4 SMBus [0c05]: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] [1106:3057] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: via686a, i2c-viapro
00:07.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT82C686 AC97 Audio Controller [1106:3058] (rev 50)
Subsystem: Giga-byte Technology Device [1458:a004]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at d800 [size=4]
Region 2: I/O ports at d400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: VIA 82xx Audio
Kernel modules: snd-via82xx
00:0a.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139 [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at dfffff00 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: 8139too
Kernel modules: 8139cp, 8139too
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Rage XL AGP 2X [1002:474d] (rev 65) (prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc Xpert 98 RXL AGP 2X [1002:0008]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 9800 [size=256]
Region 2: Memory at dfeff000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at dfec0000 [disabled] [size=128K]
Capabilities: [50] AGP version 1.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [5c] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-- System Information:
Debian Release: 5.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-1-vserver-686 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-1-vserver-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.26-1-vserver-686 recommends:
ii libc6-i686 2.7-16 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-1-vserver-686 suggests:
ii grub 0.97-47lenny1 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
linux-image-2.6.26-1-vserver-686/postinst/old-dir-initrd-link-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-vserver-686/preinst/initrd-2.6.26-1-vserver-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-vserver-686/preinst/failed-to-move-modules-2.6.26-1-vserver-686:
linux-image-2.6.26-1-vserver-686/preinst/overwriting-modules-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/postinst/bootloader-test-error-2.6.26-1-vserver-686:
linux-image-2.6.26-1-vserver-686/prerm/would-invalidate-boot-loader-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/postinst/depmod-error-initrd-2.6.26-1-vserver-686: false
linux-image-2.6.26-1-vserver-686/prerm/removing-running-kernel-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/postinst/old-initrd-link-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/preinst/lilo-initrd-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/preinst/abort-install-2.6.26-1-vserver-686:
linux-image-2.6.26-1-vserver-686/preinst/elilo-initrd-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/postinst/old-system-map-link-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/preinst/abort-overwrite-2.6.26-1-vserver-686:
linux-image-2.6.26-1-vserver-686/postinst/bootloader-error-2.6.26-1-vserver-686:
linux-image-2.6.26-1-vserver-686/postinst/create-kimage-link-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-vserver-686/preinst/bootloader-initrd-2.6.26-1-vserver-686: true
linux-image-2.6.26-1-vserver-686/postinst/depmod-error-2.6.26-1-vserver-686: false
--- End Message ---