[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#607793: marked as done (linux-image-2.6.26-2-686: scsi related kernel panic in 686 during boot, works in 486)

Your message dated Fri, 5 Jul 2013 20:16:22 +0200
with message-id <20130705181622.GF8593@pisco.westfalen.local>
and subject line Closing
has caused the Debian Bug report #607793,
regarding linux-image-2.6.26-2-686: scsi related kernel panic in 686 during boot, works in 486
to be marked as done.

This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.

(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)


-- 
607793: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=607793
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message --- 
Package: linux-2.6
Version: 2.6.26-26lenny1
Severity: normal

I've recently installed Lenny on an old HP NetServer E60 machine.
The installer worked perfectly, but after the reboot I got a kernel panic with flashing keyboard lights.

A search lead me to bug 486168, which seems very similar (same hardware, same panic message).
The comments there suggest using rescue mode to install a 486 kernel and boot it.
I did that, and the system now works, but the 486 kernel recognizes just one CPU and not both.
(I'm not sure if this is a limitation of the 486 kernel or not)

A late comment in bug 486168 suggests disabling the memory hole in the BIOS settings.
I checked the BIOS settings on my machine and the memory hole is disabled, yet the kernel panic still happens.

I'd like to load the 686 kernel for increased performance, and possibly to take advantage of SMP.

-- Package-specific info:
** Kernel log: boot messages should be attached

Can't make it save the boot messages to a file, so uploaded as YouTube video at: 
 http://www.youtube.com/watch?v=0ahFTUIY4ZY
I hope the quality is enough. crash it around 00:22

Note that I edited the kernel command line in grub.
I did this to remove the "quiet" option, so that more info is on screen.

** Model information
HP NetServer E60

** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
allow-hotplug eth1
iface eth1 inet dhcp

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] (rev 03)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 64
	Region 0: Memory at 30000000 (32-bit, prefetchable) [size=256M]
	Capabilities: [a0] AGP version 1.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
	Kernel driver in use: agpgart-intel
	Kernel modules: intel-agp

00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 128
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: fc200000-fc2fffff
	Prefetchable memory behind bridge: fd000000-fdffffff
	Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B+
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Kernel modules: shpchp

00:04.0 ISA bridge [0601]: Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:04.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01) (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32
	Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
	Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
	Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
	Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
	Region 4: I/O ports at 1860 [size=16]
	Kernel driver in use: PIIX_IDE
	Kernel modules: piix

00:04.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB [8086:7112] (rev 01) (prog-if 00 [UHCI])
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32
	Interrupt: pin D routed to IRQ 19
	Region 4: I/O ports at 1840 [size=32]
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci-hcd

00:04.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 02)
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin ? routed to IRQ 9
	Kernel driver in use: piix4_smbus
	Kernel modules: i2c-piix4

00:05.0 SCSI storage controller [0100]: Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 [9004:7895] (rev 04)
	Subsystem: Adaptec AHA-2940U/2940UW Dual AHA-394xAU/AUW/AUWD AIC-7895B [9004:7895]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (2000ns min, 2000ns max)
	Interrupt: pin A routed to IRQ 18
	Region 0: I/O ports at 1000 [disabled] [size=256]
	Region 1: Memory at fc100000 (32-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at 20100000 [disabled] [size=64K]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: aic7xxx
	Kernel modules: aic7xxx

00:05.1 SCSI storage controller [0100]: Adaptec AHA-2940U/UW / AHA-39xx / AIC-7895 [9004:7895] (rev 04)
	Subsystem: Adaptec AHA-2940U/2940UW Dual AHA-394xAU/AUW/AUWD AIC-7895B [9004:7895]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (2000ns min, 2000ns max)
	Interrupt: pin B routed to IRQ 18
	Region 0: I/O ports at 1400 [disabled] [size=256]
	Region 1: Memory at fc101000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: aic7xxx
	Kernel modules: aic7xxx

00:06.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 08)
	Subsystem: Hewlett-Packard Company NetServer 10/100TX [103c:10ca]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 19
	Region 0: Memory at fc102000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at 1800 [size=64]
	Region 2: Memory at fc000000 (32-bit, non-prefetchable) [size=1M]
	[virtual] Expansion ROM at 20000000 [disabled] [size=1M]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=2 PME-
	Kernel driver in use: e100
	Kernel modules: eepro100, e100

00:0c.0 PCI bridge [0604]: Digital Equipment Corporation DECchip 21152 [1011:0024] (rev 03) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 57, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=36
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: fc300000-fc3fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+
	Kernel modules: shpchp

01:00.0 VGA compatible controller [0300]: ATI Technologies Inc 3D Rage IIC AGP [1002:475a] (rev 7a) (prog-if 00 [VGA controller])
	Subsystem: ATI Technologies Inc Rage 3D Pro AGP 2x XPERT 98 [1002:0084]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 66 (2000ns min), Cache Line Size: 32 bytes
	Region 0: Memory at fd000000 (32-bit, prefetchable) [size=16M]
	Region 1: I/O ports at 9000 [size=256]
	Region 2: Memory at fc200000 (32-bit, non-prefetchable) [size=4K]
	[virtual] Expansion ROM at fc220000 [disabled] [size=128K]
	Capabilities: [5c] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:03.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
	Subsystem: Realtek Semiconductor Co., Ltd. RT8139 [10ec:8139]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32 (8000ns min, 16000ns max)
	Interrupt: pin A routed to IRQ 19
	Region 0: I/O ports at 2000 [size=256]
	Region 1: Memory at fc300000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: 8139too
	Kernel modules: 8139too, 8139cp


** USB devices:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


-- System Information:
Debian Release: 5.0.7
  APT prefers stable
  APT policy: (500, 'stable')
Architecture: i386 (i686)

Kernel: Linux 2.6.26-2-486
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-2-686 depends on:
ii  debconf [debconf-2.0]         1.5.24     Debian configuration management sy
ii  initramfs-tools [linux-initra 0.92o      tools for generating an initramfs
ii  module-init-tools             3.4-1      tools for managing Linux kernel mo

Versions of packages linux-image-2.6.26-2-686 recommends:
ii  libc6-i686                  2.7-18lenny6 GNU C Library: Shared libraries [i

Versions of packages linux-image-2.6.26-2-686 suggests:
ii  grub                       0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn  linux-doc-2.6.26           <none>        (no description available)

Versions of packages linux-image-2.6.26-2-686 is related to:
pn  firmware-bnx2                 <none>     (no description available)
pn  firmware-bnx2x                <none>     (no description available)
pn  firmware-ipw2x00              <none>     (no description available)
pn  firmware-ivtv                 <none>     (no description available)
pn  firmware-iwlwifi              <none>     (no description available)
pn  firmware-linux                <none>     (no description available)
pn  firmware-linux-nonfree        <none>     (no description available)
pn  firmware-qlogic               <none>     (no description available)
pn  firmware-ralink               <none>     (no description available)

-- debconf information:
  linux-image-2.6.26-2-686/postinst/bootloader-error-2.6.26-2-686:
  shared/kernel-image/really-run-bootloader: true
  linux-image-2.6.26-2-686/postinst/old-dir-initrd-link-2.6.26-2-686: true
  linux-image-2.6.26-2-686/preinst/overwriting-modules-2.6.26-2-686: true
  linux-image-2.6.26-2-686/postinst/bootloader-test-error-2.6.26-2-686:
  linux-image-2.6.26-2-686/postinst/depmod-error-2.6.26-2-686: false
  linux-image-2.6.26-2-686/preinst/bootloader-initrd-2.6.26-2-686: true
  linux-image-2.6.26-2-686/preinst/abort-overwrite-2.6.26-2-686:
  linux-image-2.6.26-2-686/preinst/abort-install-2.6.26-2-686:
  linux-image-2.6.26-2-686/postinst/depmod-error-initrd-2.6.26-2-686: false
  linux-image-2.6.26-2-686/postinst/create-kimage-link-2.6.26-2-686: true
  linux-image-2.6.26-2-686/preinst/failed-to-move-modules-2.6.26-2-686:
  linux-image-2.6.26-2-686/preinst/initrd-2.6.26-2-686:
  linux-image-2.6.26-2-686/preinst/lilo-has-ramdisk:
  linux-image-2.6.26-2-686/prerm/would-invalidate-boot-loader-2.6.26-2-686: true
  linux-image-2.6.26-2-686/postinst/kimage-is-a-directory:
  linux-image-2.6.26-2-686/postinst/old-initrd-link-2.6.26-2-686: true
  linux-image-2.6.26-2-686/preinst/elilo-initrd-2.6.26-2-686: true
  linux-image-2.6.26-2-686/preinst/lilo-initrd-2.6.26-2-686: true
  linux-image-2.6.26-2-686/prerm/removing-running-kernel-2.6.26-2-686: true
  linux-image-2.6.26-2-686/postinst/old-system-map-link-2.6.26-2-686: true

--- End Message ---
--- Begin Message --- 
Hi,
your bug has been filed against the "linux-2.6" source package and was filed for
a kernel older than the recently released Debian 7.x / Wheezy with a severity
less than important.

We don't have the ressources to reproduce the complete backlog of all older kernel
bugs, so we're closing this bug for now. If you can reproduce the bug with Debian Wheezy
or a more recent kernel from testing or unstable, please reopen the bug by sending
a mail to control@bugs.debian.org with the following three commands included in the
mail:

reopen BUGNUMBER
reassign BUGNUMBER src:linux
thanks

Cheers,
        Moritz

--- End Message ---
Reply to: