Bug#714959: linux-image-3.2.0-4-kirkwood mdraid array fails to assemble b/c drives are not yet ready (sata_mv)
Package: src:linux
Version: 3.2.46-1
Severity: normal
Tags: upstream patch
Dear Maintainer,
On my QNAP TS-412, after a clean install of Wheezy, the kernel fails to bring up all sata ports (using Marvell 88SX7042 via sata_mv driver) before md/raid tries to assemble the array.
The same disks/array work in a different model (TS-410) and the drives/array from said TS-410 also fail in my TS-412.
At the same time, using the original QNAP firmware, everything works as expected.
The only discernable differences between the devices that I could find (they share the exact same SoC and SATA Model ID and revision), apart from the core clock speed, is that the TS-412 shows some sort of spin-up delay / staggering behaviour while the TS-410 does not.
Now, having had a look at the most recent GPL code package from QNAP that I could find here:
http://sourceforge.net/projects/qosgpl/
I found that they have a version 3.4.6 kernel tree.
The file drivers/ata/sata_mv.c contains some changes regarding the delay while initializing the hardware.
Using this as a blueprint, I patched the linux-image-3.2.0-4 source file accordingly.
The resulting kernel works for me: The delay ensures that all drives are up and the raid array comes up.
I discussed this with others on debian-arm@lists.debian.org and while we agree that this kind of patch is a mere band-aid, we wanted to point out that there may be some issue concerning timing/delays with this kernel module.
Maybe there is a more elegant / targeted approach to solving this?
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
Processor : Feroceon 88FR131 rev 1 (v5l)
Hardware : QNAP TS-41x
Revision : 0000
** PCI devices:
00:00.0 Host bridge [0600]: Marvell Technology Group Ltd. 88F6281 [Kirkwood] ARM SoC [11ab:6281] (rev 03)
Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at <ignored> (64-bit, prefetchable)
Capabilities: <access denied>
00:01.0 SCSI storage controller [0100]: Marvell Technology Group Ltd. 88SX7042 PCI-e 4-port SATA-II [11ab:7042] (rev 02)
Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=1M]
Region 2: I/O ports at 1000 [size=256]
Capabilities: <access denied>
Kernel driver in use: sata_mv
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
-- System Information:
Debian Release: 7.1
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: armel (armv5tel)
Kernel: Linux 3.2.46
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-kirkwood depends on:
ii debconf [debconf-2.0] 1.5.49
ii initramfs-tools [linux-initramfs-tool] 0.109.1
ii kmod 9-3
ii linux-base 3.5
Versions of packages linux-image-3.2.0-4-kirkwood recommends:
pn firmware-linux-free <none>
pn uboot-mkimage <none>
Versions of packages linux-image-3.2.0-4-kirkwood suggests:
pn debian-kernel-handbook <none>
pn fdutils <none>
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-kirkwood is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-kirkwood/postinst/missing-firmware-3.2.0-4-kirkwood:
linux-image-3.2.0-4-kirkwood/prerm/removing-running-kernel-3.2.0-4-kirkwood: true
linux-image-3.2.0-4-kirkwood/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-kirkwood/postinst/depmod-error-initrd-3.2.0-4-kirkwood: false
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-kirkwood (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 Debian 3.2.46-1
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: QNAP TS-41x
[ 0.000000] Ignoring unrecognised tag 0x41000403
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c0441aa4, node_mem_map c04a8000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/ram initrd=0xa00000,0x900000 ramdisk=34816
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 245876k/245876k available, 16268k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc03e54f8 (3958 kB)
[ 0.000000] .init : 0xc03e6000 - 0xc040a000 ( 144 kB)
[ 0.000000] .data : 0xc040a000 - 0xc0444800 ( 234 kB)
[ 0.000000] .bss : 0xc0444824 - 0xc04a7e6c ( 398 kB)
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 7.755104] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 7.844742] pid_max: default: 32768 minimum: 301
[ 7.844878] Security Framework initialized
[ 7.844975] Mount-cache hash table entries: 512
[ 7.845318] Initializing cgroup subsys cpuacct
[ 7.845361] Initializing cgroup subsys memory
[ 7.845399] Initializing cgroup subsys devices
[ 7.845421] Initializing cgroup subsys freezer
[ 7.845440] Initializing cgroup subsys net_cls
[ 7.845457] Initializing cgroup subsys blkio
[ 7.845487] Initializing cgroup subsys perf_event
[ 7.845595] CPU: Testing write buffer coherency: ok
[ 7.846840] devtmpfs: initialized
[ 7.848607] print_constraints: dummy:
[ 7.848877] NET: Registered protocol family 16
[ 7.849650] Kirkwood: MV88F6281-A1, TCLK=200000000.
[ 7.849687] Feroceon L2: Enabling L2
[ 7.849732] Feroceon L2: Cache support initialised.
[ 7.850320] initial MPP regs: 11112222 43303311 33330004 33003333 00000033 00000000 00000000
[ 7.850347] final MPP regs: 11112222 43303311 33330004 33003333 00000033 00000000 00000000
[ 7.891193] Kirkwood PCIe port 0:
[ 7.891205] link up
[ 7.891241] PCI: bus0 uses PCIe port 0
[ 7.891398] pci 0000:00:00.0: [11ab:6281] type 0 class 0x000580
[ 7.891421] pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref]
[ 7.891435] pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0fffffff]
[ 7.891468] pci 0000:00:00.0: supports D1 D2
[ 7.891509] pci 0000:00:01.0: [11ab:7042] type 0 class 0x000100
[ 7.891537] pci 0000:00:01.0: reg 10: [mem 0x14000000-0x140fffff 64bit]
[ 7.891554] pci 0000:00:01.0: reg 18: [io 0x0000-0x00ff]
[ 7.891656] PCI: bus0: Fast back to back transfers disabled
[ 7.891925] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit]
[ 7.891964] pci 0000:00:01.0: BAR 2: assigned [io 0x1000-0x10ff]
[ 7.893620] bio: create slab <bio-0> at 0
[ 7.894026] vgaarb: loaded
[ 7.894598] Switching to clocksource orion_clocksource
[ 7.908844] NET: Registered protocol family 2
[ 7.909086] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 7.909710] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 7.909909] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 7.910015] TCP: Hash tables configured (established 8192 bind 8192)
[ 7.910034] TCP reno registered
[ 7.910050] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 7.910082] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 7.910305] NET: Registered protocol family 1
[ 7.910366] PCI: CLS 32 bytes, default 32
[ 7.910521] Unpacking initramfs...
[ 8.328757] Freeing initrd memory: 9216K
[ 8.328808] NetWinder Floating Point Emulator V0.97 (double precision)
[ 8.329417] audit: initializing netlink socket (disabled)
[ 8.329482] type=2000 audit(0.560:1): initialized
[ 8.330694] VFS: Disk quotas dquot_6.5.2
[ 8.330796] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.330916] JFFS2 version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9\xffffffa9 2001-2006 Red Hat, Inc.
[ 8.331271] msgmni has been set to 498
[ 8.332768] alg: No test for stdrng (krng)
[ 8.332897] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 8.332929] io scheduler noop registered
[ 8.332945] io scheduler deadline registered
[ 8.333007] io scheduler cfq registered (default)
[ 8.333119] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 8.333165] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 8.364675] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 8.404674] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 8.444674] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 8.484670] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 8.485034] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 8.505588] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 8.525878] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 8.527390] m25p80 spi0.0: m25p128 (16384 Kbytes)
[ 8.527423] Creating 6 MTD partitions on "spi_flash":
[ 8.527446] 0x000000000000-0x000000080000 : "U-Boot"
[ 8.528346] 0x000000200000-0x000000400000 : "Kernel"
[ 8.529193] 0x000000400000-0x000000d00000 : "RootFS1"
[ 8.530053] 0x000000d00000-0x000001000000 : "RootFS2"
[ 8.530927] 0x000000080000-0x0000000c0000 : "U-Boot Config"
[ 8.531820] 0x0000000c0000-0x000000200000 : "NAS Config"
[ 8.532956] mousedev: PS/2 mouse device common for all mice
[ 9.534663] rtc-mv rtc-mv: internal RTC not ticking
[ 9.534788] i2c /dev entries driver
[ 9.538672] rtc-s35390a 0-0030: rtc core: registered rtc-s35390a as rtc0
[ 9.538800] cpuidle: using governor ladder
[ 9.538888] cpuidle: using governor menu
[ 9.539680] TCP cubic registered
[ 9.539704] NET: Registered protocol family 17
[ 9.539735] Registering the dns_resolver key type
[ 9.539783] Gating clock of unused units
[ 9.539791] before: 0x00cfc1dd
[ 9.539797] after: 0x00cfc1cd
[ 9.540227] registered taskstats version 1
[ 9.541322] rtc-s35390a 0-0030: setting system clock to 2013-07-04 06:14:42 UTC (1372918482)
[ 9.541404] Initializing network drop monitor service
[ 9.541942] Freeing init memory: 144K
[ 9.605208] udevd[51]: starting version 175
[ 9.764781] SCSI subsystem initialized
[ 9.858461] libata version 3.00 loaded.
[ 9.860182] sata_mv 0000:00:01.0: version 1.28
[ 9.860276] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 9.860465] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 9.880706] scsi0 : sata_mv
[ 9.889205] scsi1 : sata_mv
[ 9.893444] scsi2 : sata_mv
[ 9.896842] scsi3 : sata_mv
[ 9.897103] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[ 9.897137] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[ 9.897165] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[ 9.897191] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[ 9.897902] sata_mv sata_mv.0: version 1.28
[ 9.898028] sata_mv sata_mv.0: slots 32 ports 2
[ 9.902528] scsi4 : sata_mv
[ 9.906355] scsi5 : sata_mv
[ 9.906626] ata5: SATA max UDMA/133 irq 21
[ 9.906649] ata6: SATA max UDMA/133 irq 21
[ 10.264668] ata5: SATA link down (SStatus 0 SControl F300)
[ 10.404684] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 10.444708] ata1.00: ATA-8: Hitachi HDS721010DLE630, MS2OA600, max UDMA/133
[ 10.444737] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 10.504708] ata1.00: configured for UDMA/133
[ 10.505075] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72101 MS2O PQ: 0 ANSI: 5
[ 11.014683] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 11.054709] ata2.00: ATA-8: Hitachi HDS721010DLE630, MS2OA600, max UDMA/133
[ 11.054738] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 11.114709] ata2.00: configured for UDMA/133
[ 11.115044] scsi 1:0:0:0: Direct-Access ATA Hitachi HDS72101 MS2O PQ: 0 ANSI: 5
[ 11.624681] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 11.664706] ata3.00: ATA-8: Hitachi HDS721010DLE630, MS2OA600, max UDMA/133
[ 11.664735] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 11.724706] ata3.00: configured for UDMA/133
[ 11.725031] scsi 2:0:0:0: Direct-Access ATA Hitachi HDS72101 MS2O PQ: 0 ANSI: 5
[ 12.074678] ata4: SATA link down (SStatus 0 SControl 300)
[ 12.424655] ata6: SATA link down (SStatus 0 SControl F300)
[ 12.479344] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 12.479384] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 12.479631] sd 0:0:0:0: [sda] Write Protect is off
[ 12.479656] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 12.479760] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.484871] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 12.484911] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 12.485157] sd 1:0:0:0: [sdb] Write Protect is off
[ 12.485182] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 12.485286] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.487781] sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 12.487818] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[ 12.488058] sd 2:0:0:0: [sdc] Write Protect is off
[ 12.488083] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 12.488187] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.495958] sdb: sdb1
[ 12.497427] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 12.498854] sdc: sdc1
[ 12.500229] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 12.519757] sda: sda1
[ 12.522913] sd 0:0:0:0: [sda] Attached SCSI disk
[ 12.942809] md: md0 stopped.
[ 12.956998] md: bind<sdb1>
[ 12.957437] md: bind<sdc1>
[ 12.957825] md: bind<sda1>
[ 13.154752] raid6: int32x1 79 MB/s
[ 13.324822] raid6: int32x2 123 MB/s
[ 13.495098] raid6: int32x4 125 MB/s
[ 13.664815] raid6: int32x8 156 MB/s
[ 13.664835] raid6: using algorithm int32x8 (156 MB/s)
[ 13.666762] async_tx: api initialized (async)
[ 13.668333] xor: measuring software checksum speed
[ 13.714636] arm4regs : 1090.800 MB/sec
[ 13.764640] 8regs : 654.800 MB/sec
[ 13.814637] 32regs : 906.400 MB/sec
[ 13.814657] xor: using function: arm4regs (1090.800 MB/sec)
[ 13.814714] ata4: exception Emask 0x10 SAct 0x0 SErr 0x4010000 action 0xe frozen
[ 13.814742] ata4: edma_err_cause=00000010 pp_flags=00000000, dev connect
[ 13.814766] ata4: SError: { PHYRdyChg DevExch }
[ 13.814802] ata4: hard resetting link
[ 13.824504] md: raid6 personality registered for level 6
[ 13.824537] md: raid5 personality registered for level 5
[ 13.824554] md: raid4 personality registered for level 4
[ 13.825520] bio: create slab <bio-1> at 1
[ 13.825580] md/raid:md0: device sda1 operational as raid disk 0
[ 13.825603] md/raid:md0: device sdc1 operational as raid disk 2
[ 13.825623] md/raid:md0: device sdb1 operational as raid disk 1
[ 13.826720] md/raid:md0: allocated 4218kB
[ 13.826842] md/raid:md0: raid level 5 active with 3 out of 4 devices, algorithm 2
[ 13.826870] RAID conf printout:
[ 13.826878] --- level:5 rd:4 wd:3
[ 13.826886] disk 0, o:1, dev:sda1
[ 13.826894] disk 1, o:1, dev:sdb1
[ 13.826901] disk 2, o:1, dev:sdc1
[ 13.827171] created bitmap (8 pages) for device md0
[ 13.828314] md0: bitmap initialized from disk: read 1/1 pages, set 0 of 14903 bits
[ 13.904719] md0: detected capacity change from 0 to 3000205049856
[ 13.918046] md0: unknown partition table
[ 14.122752] device-mapper: uevent: version 1.0.3
[ 14.124444] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 14.857161] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 16.870316] udevd[319]: starting version 175
[ 17.243389] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 17.252350] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 17.252484] mv643xx_eth smi: probed
[ 17.280691] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:08:9b:c2:ab:8f
[ 17.355676] mv643xx_eth_port mv643xx_eth_port.1: eth1: port 0 with MAC address 00:08:9b:c2:ab:90
[ 17.556563] usbcore: registered new interface driver usbfs
[ 17.556685] usbcore: registered new interface driver hub
[ 17.563163] usbcore: registered new device driver usb
[ 17.688058] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 17.750057] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 17.750154] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 17.774826] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 17.794695] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 17.794801] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 17.794826] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 17.794850] usb usb1: Product: Marvell Orion EHCI
[ 17.794867] usb usb1: Manufacturer: Linux 3.2.0-4-kirkwood ehci_hcd
[ 17.794886] usb usb1: SerialNumber: orion-ehci.0
[ 17.795417] hub 1-0:1.0: USB hub found
[ 17.795454] hub 1-0:1.0: 1 port detected
[ 18.114739] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 18.266227] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 18.266265] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 18.266287] usb 1-1: Product: USB2.0 Hub
[ 18.267801] hub 1-1:1.0: USB hub found
[ 18.268220] hub 1-1:1.0: 4 ports detected
[ 18.741075] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 19.284722] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 19.286005] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 19.324771] ata4.00: ATA-8: Hitachi HDS721010DLE630, MS2OA600, max UDMA/133
[ 19.324813] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 19.384775] ata4.00: configured for UDMA/133
[ 19.384823] ata4: EH complete
[ 19.385162] scsi 3:0:0:0: Direct-Access ATA Hitachi HDS72101 MS2O PQ: 0 ANSI: 5
[ 19.387217] sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 19.387256] sd 3:0:0:0: [sdd] 4096-byte physical blocks
[ 19.387503] sd 3:0:0:0: [sdd] Write Protect is off
[ 19.387529] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 19.387633] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 19.414288] sdd: sdd1
[ 19.415802] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 19.489933] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 19.490148] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 19.492154] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 19.492757] sd 3:0:0:0: Attached scsi generic sg3 type 0
[ 19.889314] loop: module loaded
[ 23.309204] Adding 974844k swap on /dev/mapper/qnap-swap. Priority:-1 extents:1 across:974844k
[ 25.609352] NET: Registered protocol family 10
[ 25.882167] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.481054] RPC: Registered named UNIX socket transport module.
[ 26.481095] RPC: Registered udp transport module.
[ 26.481112] RPC: Registered tcp transport module.
[ 26.481128] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 26.641611] FS-Cache: Loaded
[ 26.913860] FS-Cache: Netfs 'nfs' registered for caching
[ 26.946236] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 29.535147] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 29.535317] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 40.354674] eth0: no IPv6 routers present
[ 249.876014] md: bind<sdd1>
[ 249.995967] RAID conf printout:
[ 249.995980] --- level:5 rd:4 wd:3
[ 249.995989] disk 0, o:1, dev:sda1
[ 249.995996] disk 1, o:1, dev:sdb1
[ 249.996004] disk 2, o:1, dev:sdc1
[ 249.996012] disk 3, o:1, dev:sdd1
[ 250.000617] md: recovery of RAID array md0
[ 250.000640] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 250.000658] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 250.000682] md: using 128k window, over a total of 976629248k.
[ 309.988791] md: md0: recovery done.
[ 310.044829] RAID conf printout:
[ 310.044840] --- level:5 rd:4 wd:4
[ 310.044848] disk 0, o:1, dev:sda1
[ 310.044856] disk 1, o:1, dev:sdb1
[ 310.044863] disk 2, o:1, dev:sdc1
[ 310.044871] disk 3, o:1, dev:sdd1
[ 363.165316] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[ 392.525245] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.46 (root@debian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #2 Mon Jul 1 12:51:39 CEST 2013
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: QNAP TS-41x
[ 0.000000] Ignoring unrecognised tag 0x41000403
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat c043daa4, node_mem_map c04a4000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/ram initrd=0xa00000,0x900000 ramdisk=34816
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 256MB = 256MB total
[ 0.000000] Memory: 245892k/245892k available, 16252k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xfe800000 ( 736 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc03e14f8 (3942 kB)
[ 0.000000] .init : 0xc03e2000 - 0xc0406000 ( 144 kB)
[ 0.000000] .data : 0xc0406000 - 0xc0440800 ( 234 kB)
[ 0.000000] .bss : 0xc0440824 - 0xc04a3e6c ( 398 kB)
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 7.757057] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[ 7.846697] pid_max: default: 32768 minimum: 301
[ 7.846832] Security Framework initialized
[ 7.846929] Mount-cache hash table entries: 512
[ 7.847271] Initializing cgroup subsys cpuacct
[ 7.847315] Initializing cgroup subsys memory
[ 7.847353] Initializing cgroup subsys devices
[ 7.847376] Initializing cgroup subsys freezer
[ 7.847395] Initializing cgroup subsys net_cls
[ 7.847412] Initializing cgroup subsys blkio
[ 7.847441] Initializing cgroup subsys perf_event
[ 7.847549] CPU: Testing write buffer coherency: ok
[ 7.848791] devtmpfs: initialized
[ 7.850548] print_constraints: dummy:
[ 7.850815] NET: Registered protocol family 16
[ 7.851588] Kirkwood: MV88F6281-A1, TCLK=200000000.
[ 7.851623] Feroceon L2: Enabling L2
[ 7.851668] Feroceon L2: Cache support initialised.
[ 7.852257] initial MPP regs: 11112222 43303311 33330004 33003333 00000033 00000000 00000000
[ 7.852284] final MPP regs: 11112222 43303311 33330004 33003333 00000033 00000000 00000000
[ 7.893130] Kirkwood PCIe port 0:
[ 7.893143] link up
[ 7.893179] PCI: bus0 uses PCIe port 0
[ 7.893336] pci 0000:00:00.0: [11ab:6281] type 0 class 0x000580
[ 7.893359] pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref]
[ 7.893374] pci 0000:00:00.0: reg 18: [mem 0x00000000-0x0fffffff]
[ 7.893407] pci 0000:00:00.0: supports D1 D2
[ 7.893449] pci 0000:00:01.0: [11ab:7042] type 0 class 0x000100
[ 7.893476] pci 0000:00:01.0: reg 10: [mem 0x14000000-0x140fffff 64bit]
[ 7.893494] pci 0000:00:01.0: reg 18: [io 0x0000-0x00ff]
[ 7.893596] PCI: bus0: Fast back to back transfers disabled
[ 7.893866] pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe00fffff 64bit]
[ 7.893904] pci 0000:00:01.0: BAR 2: assigned [io 0x1000-0x10ff]
[ 7.895567] bio: create slab <bio-0> at 0
[ 7.895974] vgaarb: loaded
[ 7.896543] Switching to clocksource orion_clocksource
[ 7.910817] NET: Registered protocol family 2
[ 7.911055] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 7.911680] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 7.911880] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 7.911985] TCP: Hash tables configured (established 8192 bind 8192)
[ 7.912004] TCP reno registered
[ 7.912021] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 7.912053] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 7.912276] NET: Registered protocol family 1
[ 7.912335] PCI: CLS 32 bytes, default 32
[ 7.912494] Unpacking initramfs...
[ 8.331423] Freeing initrd memory: 9216K
[ 8.331473] NetWinder Floating Point Emulator V0.97 (double precision)
[ 8.332081] audit: initializing netlink socket (disabled)
[ 8.332147] type=2000 audit(0.560:1): initialized
[ 8.333367] VFS: Disk quotas dquot_6.5.2
[ 8.333472] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.333593] JFFS2 version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9\xffffffa9 2001-2006 Red Hat, Inc.
[ 8.333949] msgmni has been set to 498
[ 8.335435] alg: No test for stdrng (krng)
[ 8.335566] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 8.335598] io scheduler noop registered
[ 8.335614] io scheduler deadline registered
[ 8.335677] io scheduler cfq registered (default)
[ 8.335788] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 8.335833] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 8.366622] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 8.406619] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 8.446620] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 8.486617] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 8.486982] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 8.507539] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 8.527831] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 8.529346] m25p80 spi0.0: m25p128 (16384 Kbytes)
[ 8.529379] Creating 6 MTD partitions on "spi_flash":
[ 8.529402] 0x000000000000-0x000000080000 : "U-Boot"
[ 8.530311] 0x000000200000-0x000000400000 : "Kernel"
[ 8.531163] 0x000000400000-0x000000d00000 : "RootFS1"
[ 8.532020] 0x000000d00000-0x000001000000 : "RootFS2"
[ 8.532905] 0x000000080000-0x0000000c0000 : "U-Boot Config"
[ 8.533807] 0x0000000c0000-0x000000200000 : "NAS Config"
[ 8.534941] mousedev: PS/2 mouse device common for all mice
[ 9.536610] rtc-mv rtc-mv: internal RTC not ticking
[ 9.536735] i2c /dev entries driver
[ 9.540616] rtc-s35390a 0-0030: rtc core: registered rtc-s35390a as rtc0
[ 9.540744] cpuidle: using governor ladder
[ 9.540832] cpuidle: using governor menu
[ 9.541620] TCP cubic registered
[ 9.541643] NET: Registered protocol family 17
[ 9.541674] Registering the dns_resolver key type
[ 9.541749] Gating clock of unused units
[ 9.541757] before: 0x00cfc1dd
[ 9.541764] after: 0x00cfc1cd
[ 9.542185] registered taskstats version 1
[ 9.543287] rtc-s35390a 0-0030: setting system clock to 2013-07-04 06:37:41 UTC (1372919861)
[ 9.543372] Initializing network drop monitor service
[ 9.543911] Freeing init memory: 144K
[ 9.607148] udevd[51]: starting version 175
[ 9.765800] SCSI subsystem initialized
[ 9.859446] libata version 3.00 loaded.
[ 9.861157] sata_mv 0000:00:01.0: version 1.28
[ 9.861257] PCI: enabling device 0000:00:01.0 (0140 -> 0143)
[ 9.861380] Wait 5 seconds to initialize scsi 2.
[ 14.851929] Wait 5 seconds to initialize scsi 3.
[ 19.842414] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
[ 19.842463] sched: RT throttling activated
[ 19.938250] scsi0 : sata_mv
[ 19.938996] scsi1 : sata_mv
[ 19.939543] scsi2 : sata_mv
[ 19.940074] scsi3 : sata_mv
[ 19.940318] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9
[ 19.940351] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9
[ 19.940378] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9
[ 19.940405] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9
[ 19.940544] sata_mv sata_mv.0: version 1.28
[ 19.940670] sata_mv sata_mv.0: slots 32 ports 2
[ 19.949479] scsi4 : sata_mv
[ 19.951440] scsi5 : sata_mv
[ 19.951711] ata5: SATA max UDMA/133 irq 21
[ 19.951735] ata6: SATA max UDMA/133 irq 21
[ 20.296602] ata5: SATA link down (SStatus 0 SControl F300)
[ 20.446629] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 20.486653] ata1.00: ATA-8: Hitachi HDS721010DLE630, MS2OA600, max UDMA/133
[ 20.486682] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 20.546653] ata1.00: configured for UDMA/133
[ 20.547011] scsi 0:0:0:0: Direct-Access ATA Hitachi HDS72101 MS2O PQ: 0 ANSI: 5
[ 21.056628] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 21.096652] ata2.00: ATA-8: Hitachi HDS721010DLE630, MS2OA600, max UDMA/133
[ 21.096681] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 21.156652] ata2.00: configured for UDMA/133
[ 21.156985] scsi 1:0:0:0: Direct-Access ATA Hitachi HDS72101 MS2O PQ: 0 ANSI: 5
[ 21.666624] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 21.706651] ata3.00: ATA-8: Hitachi HDS721010DLE630, MS2OA600, max UDMA/133
[ 21.706679] ata3.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 21.766654] ata3.00: configured for UDMA/133
[ 21.766963] scsi 2:0:0:0: Direct-Access ATA Hitachi HDS72101 MS2O PQ: 0 ANSI: 5
[ 22.276626] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 22.316652] ata4.00: ATA-8: Hitachi HDS721010DLE630, MS2OA600, max UDMA/133
[ 22.316681] ata4.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 22.376651] ata4.00: configured for UDMA/133
[ 22.376965] scsi 3:0:0:0: Direct-Access ATA Hitachi HDS72101 MS2O PQ: 0 ANSI: 5
[ 22.726606] ata6: SATA link down (SStatus 0 SControl F300)
[ 22.803782] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 22.803823] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 22.804071] sd 0:0:0:0: [sda] Write Protect is off
[ 22.804097] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 22.804202] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.806633] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 22.806670] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 22.806916] sd 1:0:0:0: [sdb] Write Protect is off
[ 22.806941] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 22.807044] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.810094] sd 2:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 22.810132] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[ 22.810376] sd 2:0:0:0: [sdc] Write Protect is off
[ 22.810401] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 22.810506] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.812671] sd 3:0:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 22.812707] sd 3:0:0:0: [sdd] 4096-byte physical blocks
[ 22.812950] sd 3:0:0:0: [sdd] Write Protect is off
[ 22.812975] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 22.813080] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.815960] sdb: sdb1
[ 22.816988] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 22.825440] sdc: sdc1
[ 22.826495] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 22.837756] sdd: sdd1
[ 22.840880] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 22.845740] sda: sda1
[ 22.851471] sd 0:0:0:0: [sda] Attached SCSI disk
[ 23.273571] md: md0 stopped.
[ 23.291083] md: bind<sdb1>
[ 23.291504] md: bind<sdc1>
[ 23.291898] md: bind<sdd1>
[ 23.295943] md: bind<sda1>
[ 23.496731] raid6: int32x1 80 MB/s
[ 23.666769] raid6: int32x2 123 MB/s
[ 23.837061] raid6: int32x4 125 MB/s
[ 24.006755] raid6: int32x8 156 MB/s
[ 24.006775] raid6: using algorithm int32x8 (156 MB/s)
[ 24.008864] async_tx: api initialized (async)
[ 24.010444] xor: measuring software checksum speed
[ 24.056588] arm4regs : 1091.600 MB/sec
[ 24.106582] 8regs : 654.800 MB/sec
[ 24.156583] 32regs : 906.400 MB/sec
[ 24.156602] xor: using function: arm4regs (1091.600 MB/sec)
[ 24.165874] md: raid6 personality registered for level 6
[ 24.165907] md: raid5 personality registered for level 5
[ 24.165924] md: raid4 personality registered for level 4
[ 24.166922] bio: create slab <bio-1> at 1
[ 24.166983] md/raid:md0: device sda1 operational as raid disk 0
[ 24.167006] md/raid:md0: device sdd1 operational as raid disk 3
[ 24.167027] md/raid:md0: device sdc1 operational as raid disk 2
[ 24.167046] md/raid:md0: device sdb1 operational as raid disk 1
[ 24.168140] md/raid:md0: allocated 4218kB
[ 24.168269] md/raid:md0: raid level 5 active with 4 out of 4 devices, algorithm 2
[ 24.168298] RAID conf printout:
[ 24.168305] --- level:5 rd:4 wd:4
[ 24.168313] disk 0, o:1, dev:sda1
[ 24.168321] disk 1, o:1, dev:sdb1
[ 24.168328] disk 2, o:1, dev:sdc1
[ 24.168335] disk 3, o:1, dev:sdd1
[ 24.168600] created bitmap (8 pages) for device md0
[ 24.169746] md0: bitmap initialized from disk: read 1/1 pages, set 0 of 14903 bits
[ 24.226849] md0: detected capacity change from 0 to 3000205049856
[ 24.235711] md0: unknown partition table
[ 24.444933] device-mapper: uevent: version 1.0.3
[ 24.446661] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 25.005817] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 26.264233] udevd[328]: starting version 175
[ 26.595617] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 26.607688] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 26.607822] mv643xx_eth smi: probed
[ 26.675522] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:08:9b:c2:ab:8f
[ 26.732667] mv643xx_eth_port mv643xx_eth_port.1: eth1: port 0 with MAC address 00:08:9b:c2:ab:90
[ 26.980870] usbcore: registered new interface driver usbfs
[ 26.980990] usbcore: registered new interface driver hub
[ 26.996450] usbcore: registered new device driver usb
[ 27.015133] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 27.085357] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 27.085458] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 27.106654] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 27.126943] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 27.127050] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 27.127075] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 27.127100] usb usb1: Product: Marvell Orion EHCI
[ 27.127116] usb usb1: Manufacturer: Linux 3.2.46 ehci_hcd
[ 27.127134] usb usb1: SerialNumber: orion-ehci.0
[ 27.127672] hub 1-0:1.0: USB hub found
[ 27.127707] hub 1-0:1.0: 1 port detected
[ 27.446682] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 27.598010] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 27.598049] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 27.598072] usb 1-1: Product: USB2.0 Hub
[ 27.599612] hub 1-1:1.0: USB hub found
[ 27.600015] hub 1-1:1.0: 4 ports detected
[ 28.263107] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 28.628420] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 29.037362] loop: module loaded
[ 31.941871] Adding 974844k swap on /dev/mapper/qnap-swap. Priority:-1 extents:1 across:974844k
[ 33.814234] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[ 35.188676] NET: Registered protocol family 10
[ 35.191088] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 35.276736] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 38.745225] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 38.745395] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 39.080067] mv643xx_eth_port mv643xx_eth_port.1: eth1: link up, 1000 Mb/s, full duplex, flow control disabled
[ 39.080213] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 45.289257] RPC: Registered named UNIX socket transport module.
[ 45.289297] RPC: Registered udp transport module.
[ 45.289313] RPC: Registered tcp transport module.
[ 45.289329] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 45.409206] FS-Cache: Loaded
[ 45.481844] FS-Cache: Netfs 'nfs' registered for caching
[ 45.531734] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 49.346608] eth0: no IPv6 routers present
[ 49.376597] eth1: no IPv6 routers present
--- linux-source-3.2-orig/drivers/ata/sata_mv.c 2013-05-30 15:35:16.000000000 +0200
+++ linux-source-3.2/drivers/ata/sata_mv.c 2013-07-01 11:30:43.094185000 +0200
@@ -73,6 +73,10 @@
#define DRV_NAME "sata_mv"
#define DRV_VERSION "1.28"
+//Patch by QNAP: delay SATA disk initialization
+#define QMV_SATA_INIT_DELAY_PHASE 5000 //milliseconds
+////////////////////////////////////////////////////////////////
+
/*
* module options
*/
@@ -4329,7 +4333,11 @@
struct ata_port *ap = host->ports[port];
void __iomem *port_mmio = mv_port_base(hpriv->base, port);
unsigned int offset = port_mmio - hpriv->base;
-
+ // marvell 7042 port 2 port 3 will power on by order every 5 sec
+ if( (port==2) || (port == 3) ){
+ printk("Wait %d seconds to initialize scsi %d.\n",QMV_SATA_INIT_DELAY_PHASE/1000,port);
+ mdelay(QMV_SATA_INIT_DELAY_PHASE);
+ }
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio");
ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port");
}
Reply to: