--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: ath5k: regression: unable to connect to AP on channel 13
- From: "John S. Skogtvedt" <jss@bzz.no>
- Date: Sat, 23 Jan 2010 21:24:05 +0100
- Message-id: <20100123202405.28084.64324.reportbug@sh>
Package: linux-2.6
Version: 2.6.32-5
Severity: normal
With kernels 2.6.26 and 2.6.30 I am able to connect to an AP on channel 13 without problems, with the following /etc/modprobe.d/cfg80211_reg.conf :
options cfg80211 ieee80211_regdom=EU
On linux-image-2.6.32-trunk-686 I am not able to connect, nor does the AP show up when running iwlist scan.
I have tried both with and without the ieee80211_regdom option, as well as ieee80211_regdom=NO. cfg80211 autodetects regulatory domain DK if nothing is specified.
My configuration is as follows:
auto wlan0
iface wlan0 inet static
wpa-driver wext
wpa-ssid pingvin
wpa-psk mykey
address 192.168.1.10
netmask 255.255.255.0
gateway 192.168.1.1
dns-nameservers ...
dns-search ...
dmesg output with ieee80211_regdom=NO:
$ grep -e "Linux version" -e ath5k -e cfg80211 /var/log/dmesg.0
[ 0.000000] Linux version 2.6.32-trunk-686 (Debian 2.6.32-5) (ben@decadent.org.uk) (gcc version 4.3.4 (Debian 4.3.4-6) ) #1 SMP Sun Jan 10 06:32:16 UTC 2010
[ 8.197842] cfg80211: Using static regulatory domain info
[ 8.197846] cfg80211: Regulatory domain: US
[ 8.198141] cfg80211: Calling CRDA for country: US
[ 8.198190] cfg80211: Calling CRDA for country: NO
[ 8.400510] ath5k 0000:01:0a.0: PCI INT A -> Link[APC1] -> GSI 16 (level, high) -> IRQ 16
[ 8.400602] ath5k 0000:01:0a.0: registered as 'phy0'
[ 9.251795] ath5k phy0: Atheros AR2414 chip found (MAC: 0x79, PHY: 0x45)
[ 9.252114] cfg80211: Calling CRDA for country: DK
[ 61.626958] ath5k phy0: noise floor calibration timeout (2462MHz)
Please let me know if you need any more information.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** PCI devices:
00:00.0 Host bridge [0600]: nVidia Corporation nForce2 IGP2 [10de:01e0] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=32M]
Capabilities: <access denied>
Kernel driver in use: agpgart-nvidia
00:00.1 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 0 [10de:01ea] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.2 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 4 [10de:01ee] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 3 [10de:01ed] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.4 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 2 [10de:01ec] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.5 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 5 [10de:01ef] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.0 ISA bridge [0601]: nVidia Corporation nForce2 ISA Bridge [10de:0060] (rev a4)
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard [1043:80ad]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.1 SMBus [0c05]: nVidia Corporation nForce2 SMBus (MCP) [10de:0064] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:0c11]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at e400 [size=32]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
00:02.0 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0067] (rev a4) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard [1043:0c11]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at e7001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.1 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0067] (rev a4) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard [1043:0c11]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at e7002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.2 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0068] (rev a4) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard [1043:0c11]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at e7003000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:04.0 Ethernet controller [0200]: nVidia Corporation nForce2 Ethernet Controller [10de:0066] (rev a1)
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard onboard nForce2 Ethernet [1043:80a7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at e7000000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e000 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth
00:08.0 PCI bridge [0604]: nVidia Corporation nForce2 External PCI Bridge [10de:006c] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e5000000-e6ffffff
Prefetchable memory behind bridge: c4000000-c40fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00:09.0 IDE interface [0101]: nVidia Corporation nForce2 IDE [10de:0065] (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:0c11]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: <access denied>
Kernel driver in use: AMD_IDE
00:1e.0 PCI bridge [0604]: nVidia Corporation nForce2 AGP [10de:01e8] (rev c1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: e2000000-e4ffffff
Prefetchable memory behind bridge: d0000000-dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
01:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at e6010000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at c4000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
01:09.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1 [1102:0002] (rev 0a)
Subsystem: Creative Labs SBLive! 5.1 eMicro 28028 [1102:8067]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at d400 [size=32]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
01:09.1 Input device controller [0980]: Creative Labs SB Live! Game Port [1102:7002] (rev 0a)
Subsystem: Creative Labs Gameport Joystick [1102:0020]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: I/O ports at d800 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
01:0a.0 Ethernet controller [0200]: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter [168c:0013] (rev 01)
Subsystem: D-Link System Inc D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev.B) [1186:3a13]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e6000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath5k
02:00.0 VGA compatible controller [0300]: nVidia Corporation NV44A [GeForce 6200] [10de:0221] (rev a1) (prog-if 00 [VGA controller])
Subsystem: XFX Pine Group Inc. Device [1682:2156]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 2: Memory at e3000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at e4000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
** USB devices:
Bus 003 Device 002: ID 046d:c510 Logitech, Inc. Cordless Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 046d:0a0b Logitech, Inc.
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (900, 'testing'), (800, 'unstable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.30-2-686 (SMP w/1 CPU core)
Locale: LANG=nb_NO.UTF-8, LC_CTYPE=nb_NO.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.32-trunk-686 depends on:
ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-trunk-686 recommends:
ii firmware-linux-free 2.6.32-5 Binary firmware for various driver
ii libc6-i686 2.10.2-2 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.32-trunk-686 suggests:
ii grub 0.97-59 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-trunk-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
-- debconf information excluded
--- End Message ---