Your message dated Sun, 09 Jun 2013 14:17:25 +0100 with message-id <1370783845.5614.6.camel@deadeye.wl.decadent.org.uk> and subject line Re: Bug#704153: No problem with 3.9.4 has caused the Debian Bug report #704153, regarding linux-image-3.8-trunk-amd64: Disk failure with 3.8, not with 3.7 to be marked as done. This means that you claim that the problem has been dealt with. If this is not the case it is now your responsibility to reopen the Bug report if necessary, and/or fix the problem forthwith. (NB: If you are a system administrator and have no idea what this message is talking about, this may indicate a serious mail system misconfiguration somewhere. Please contact owner@bugs.debian.org immediately.) -- 704153: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=704153 Debian Bug Tracking System Contact owner@bugs.debian.org with problems
--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.8-trunk-amd64: Disk failure with 3.8, not with 3.7
- From: Benoit Friry <benoit@friry.net>
- Date: Thu, 28 Mar 2013 11:40:01 +0100
- Message-id: <20130328104001.24194.24334.reportbug@tc2.lan>
Package: src:linux Version: 3.8.3-1~experimental.1 Severity: important Dear Maintainer, When running linux 3.8, after a while, a disk fails. /var/log/kern.log is full of: Mar 28 10:11:09 tc2 kernel: [ 3871.788922] DMA: Out of SW-IOMMU space for 65536 bytes at device 0000:00:1f.2 Mar 28 10:11:09 tc2 kernel: [ 3871.789022] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Mar 28 10:11:09 tc2 kernel: [ 3871.789028] ata2.01: failed command: READ DMA EXT Mar 28 10:11:09 tc2 kernel: [ 3871.789035] ata2.01: cmd 25/00:00:20:51:16/00:02:00:00:00/f0 tag 0 dma 262144 in Mar 28 10:11:09 tc2 kernel: [ 3871.789035] res 50/00:00:08:48:f8/00:00:8f:b6:83/fd Emask 0x40 (internal error) Mar 28 10:11:09 tc2 kernel: [ 3871.789038] ata2.01: status: { DRDY } Mar 28 10:11:09 tc2 kernel: [ 3871.865796] ata2.00: configured for UDMA/133 Mar 28 10:11:09 tc2 kernel: [ 3871.923259] ata2.01: configured for UDMA/133 Mar 28 10:11:09 tc2 kernel: [ 3871.923273] ata2: EH complete It first happened after installing 3.8-1~experimental.1. Since I use disk mirroring (md), I tried to rebuild the failing partition, but it failed again during rebuild. Of course, I though of an hardware failure. Having just upgraded to 3.8, just to be sure, I rebooting on 3.7.x~experimental.y: no more failure! Uptime of more than 2 weeks, without any problem. This morning, I install 3.8.3-1~experimental.1. After 2 hours, a disk fails. I found similar reports: http://forums.fedoraforum.org/showthread.php?t=289979&goto=newpost (comment #4) https://bugzilla.redhat.com/show_bug.cgi?id=787054 (comment #37) I'm relunctant to reboot to 3.8. If both disks fails, my RAID will not help me... Thanks, Benoit -- Package-specific info: ** Kernel log: boot messages should be attached ** Model information sys_vendor: Gigabyte Technology Co., Ltd. product_name: To be filled by O.E.M. product_version: To be filled by O.E.M. chassis_vendor: Gigabyte Technology Co., Ltd. chassis_version: To Be Filled By O.E.M. bios_vendor: American Megatrends Inc. bios_version: F4 board_vendor: Gigabyte Technology Co., Ltd. board_name: H77-DS3H board_version: x.x ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller [8086:0150] (rev 09) Subsystem: Giga-byte Technology Device [1458:5000] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor Graphics Controller [8086:0152] (rev 09) (prog-if 00 [VGA controller]) Subsystem: Giga-byte Technology Device [1458:d000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 44 Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M] Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at f000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI]) Subsystem: Giga-byte Technology Device [1458:5007] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 42 Region 0: Memory at f7e00000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) Subsystem: Giga-byte Technology Device [1458:1c3a] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 43 Region 0: Memory at f7e19000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology Device [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at f7e17000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) Subsystem: Giga-byte Technology Device [1458:a002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at f7e10000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.2 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 [8086:1e14] (rev c4) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f7d00000-f7dfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.3 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c4) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=04, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f7c00000-f7cfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI]) Subsystem: Giga-byte Technology Device [1458:5006] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at f7e16000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation H77 Express Chipset LPC Controller [8086:1e4a] (rev 04) Subsystem: Giga-byte Technology Device [1458:5001] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: lpc_ich 00:1f.2 IDE interface [0101]: Intel Corporation 7 Series/C210 Series Chipset Family 4-port SATA Controller [IDE mode] [8086:1e00] (rev 04) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Giga-byte Technology Device [1458:b005] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at f110 [size=8] Region 1: I/O ports at f100 [size=4] Region 2: I/O ports at f0f0 [size=8] Region 3: I/O ports at f0e0 [size=4] Region 4: I/O ports at f0d0 [size=16] Region 5: I/O ports at f0c0 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) Subsystem: Giga-byte Technology Device [1458:5001] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin C routed to IRQ 18 Region 0: Memory at f7e15000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at f040 [size=32] 00:1f.5 IDE interface [0101]: Intel Corporation 7 Series/C210 Series Chipset Family 2-port SATA Controller [IDE mode] [8086:1e08] (rev 04) (prog-if 85 [Master SecO PriO]) Subsystem: Giga-byte Technology Device [1458:b002] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at f0b0 [size=8] Region 1: I/O ports at f0a0 [size=4] Region 2: I/O ports at f090 [size=8] Region 3: I/O ports at f080 [size=4] Region 4: I/O ports at f070 [size=16] Region 5: I/O ports at f060 [size=16] Capabilities: <access denied> Kernel driver in use: ata_piix 02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) Subsystem: Giga-byte Technology Device [1458:e000] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 46 Region 0: Memory at f7d00000 (64-bit, non-prefetchable) [size=256K] Region 2: I/O ports at e000 [size=128] Capabilities: <access denied> Kernel driver in use: atl1c 03:00.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 30) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=03, secondary=04, subordinate=04, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f7c00000-f7cfffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8029(AS) [10ec:8029] Subsystem: Realtek Semiconductor Co., Ltd. RTL-8029(AS) [10ec:8029] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at d100 [size=32] Kernel driver in use: ne2k-pci 04:01.0 SCSI storage controller [0100]: Adaptec AIC-7850 [9004:5078] (rev 03) Subsystem: Adaptec AHA-2904/Integrated AIC-7850 [9004:7850] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (1000ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at d000 [disabled] [size=256] Region 1: Memory at f7c00000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: aic7xxx ** USB devices: Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 046d:c03e Logitech, Inc. Premium Optical Wheel Mouse (M-BT58) Bus 001 Device 004: ID 0424:2640 Standard Microsystems Corp. USB 2.0 Hub Bus 001 Device 005: ID 0424:4063 Standard Microsystems Corp. -- System Information: Debian Release: 7.0 APT prefers testing APT policy: (990, 'testing'), (500, 'unstable'), (500, 'stable'), (1, 'experimental') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 3.7-trunk-amd64 (SMP w/4 CPU cores) Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.8-trunk-amd64 depends on: ii debconf [debconf-2.0] 1.5.49 ii initramfs-tools [linux-initramfs-tool] 0.110 ii kmod 9-2 ii linux-base 3.5 ii module-init-tools 9-2 Versions of packages linux-image-3.8-trunk-amd64 recommends: ii firmware-linux-free 3.2 Versions of packages linux-image-3.8-trunk-amd64 suggests: pn debian-kernel-handbook <none> pn grub-pc | extlinux | lilo <none> pn linux-doc-3.8 <none> Versions of packages linux-image-3.8-trunk-amd64 is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information excluded
--- End Message ---
--- Begin Message ---
- To: 704153-done@bugs.debian.org
- Subject: Re: Bug#704153: No problem with 3.9.4
- From: Ben Hutchings <ben@decadent.org.uk>
- Date: Sun, 09 Jun 2013 14:17:25 +0100
- Message-id: <1370783845.5614.6.camel@deadeye.wl.decadent.org.uk>
- In-reply-to: <[🔎] 51B45AE4.4010904@friry.net>
- References: <[🔎] 51B45AE4.4010904@friry.net>
Version: 3.9.4-1 On Sun, 2013-06-09 at 12:37 +0200, Benoit Friry wrote: > I've installed and booted yesterday on linux-image-3.9-1-amd64 > (3.9.4-1), and I do not encounter any problem anymore. > > I do not have a clue about what failed, but I am not motivated to test > the issue again. > > >From my point of view, this bug can be closed. Thanks. Ben. -- Ben Hutchings Knowledge is power. France is bacon.Attachment: signature.asc
Description: This is a digitally signed message part
--- End Message ---