Bug#707330: linux-image-3.8-1-amd64: Update to 3.8 causes MD RAID1 failure
Package: src:linux
Version: 3.8.11-1
Severity: important
I have two disks, one SSD and one HDD. There are to MD RAID1 volumes
that each use one partition on the SSD and one on the HDD.
After the first reboot with 3.8, MD kicked the HDD's partitions from
both RAID devices. However, there were no actual errors logged in
kern.log, the other (non-RAID partitions) on the HDD continued to work
fine and SMART did not report any error:
May 8 20:32:18 k kernel: [ 16.967657] md/raid1:md1: Disk failure on
sdb9, disabling device.
May 8 20:32:18 k kernel: [ 16.967657] md/raid1:md1: Operation
continuing on 1 devices.
May 8 20:32:18 k kernel: [ 17.172624] RAID1 conf printout:
May 8 20:32:18 k kernel: [ 17.172629] --- wd:1 rd:2
May 8 20:32:18 k kernel: [ 17.172633] disk 0, wo:0, o:1, dev:sda6
May 8 20:32:18 k kernel: [ 17.172637] disk 1, wo:1, o:0, dev:sdb9
May 8 20:32:18 k kernel: [ 17.172791] RAID1 conf printout:
May 8 20:32:18 k kernel: [ 17.172796] --- wd:1 rd:2
May 8 20:32:18 k kernel: [ 17.172801] disk 0, wo:0, o:1, dev:sda6
...
May 8 20:33:33 k kernel: [ 94.707222] md/raid1:md0: Disk failure on
sdb7, disabling device.
May 8 20:33:33 k kernel: [ 94.707222] md/raid1:md0: Operation
continuing on 1 devices.
May 8 20:33:33 k kernel: [ 94.709046] RAID1 conf printout:
May 8 20:33:33 k kernel: [ 94.709051] --- wd:1 rd:2
May 8 20:33:33 k kernel: [ 94.709056] disk 0, wo:0, o:1, dev:sda1
May 8 20:33:33 k kernel: [ 94.709059] disk 1, wo:1, o:0, dev:sdb7
May 8 20:33:33 k kernel: [ 94.712138] RAID1 conf printout:
May 8 20:33:33 k kernel: [ 94.712141] --- wd:1 rd:2
May 8 20:33:33 k kernel: [ 94.712144] disk 0, wo:0, o:1, dev:sda1
Re-adding the devices resulted in immediate RAID failures again (see
below for the log). As there was no change with mdadm, I guess this is a
kernel bug.
Initially, the partitions on the HDD were marked as write-mostly with
mdadm. However, when re-adding the partitions, I did not specify
--write-mostly again, which (if I read mdadm's man page right) should
have lead to write-mostly not being active.
-- Package-specific info:
** Version:
Linux version 3.8-1-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Debian 3.8.11-1
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.8-1-amd64 root=UUID=16fd1e3f-26b7-41ce-b31d-ac1a9e7e9150 ro rootfstype=ext4 mtrr_spare_reg_num=3 enable_mtrr_cleanup
** Tainted: PO (4097)
* Proprietary module has been loaded.
* Out-of-tree module has been loaded.
** Kernel log:
[ 4.198739] input: HDA Intel MID Line Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input16
[ 4.199874] hda_intel: Disabling MSI
[ 4.199929] hda-intel 0000:01:00.1: Handle VGA-switcheroo audio client
[ 5.005082] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input17
[ 5.005451] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input18
[ 5.005814] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input19
[ 5.006181] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/0000:01:00.1/sound/card1/input20
[ 5.325678] EXT4-fs (md0): re-mounted. Opts: (null)
[ 5.412252] EXT4-fs (md0): re-mounted. Opts: acl
[ 5.919334] fuse init (API version 7.20)
[ 5.979129] Bridge firewalling registered
[ 5.998981] it87: Found IT8720F chip at 0x290, revision 8
[ 5.999049] it87: VID is disabled (pins used for GPIO)
[ 5.999116] it87: Routing internal VCCH to in7
[ 5.999175] it87: Beeping is supported
[ 6.251326] bio: create slab <bio-1> at 1
[ 7.830383] Adding 1572860k swap on /dev/mapper/vg0-swap. Priority:-1 extents:1 across:1572860k
[ 9.605659] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: acl
[ 9.662089] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: acl
[ 9.684424] REISERFS (device dm-2): found reiserfs format "3.6" with standard journal
[ 9.684514] REISERFS (device dm-2): using ordered data mode
[ 9.684568] reiserfs: using flush barriers
[ 9.694345] REISERFS (device dm-2): journal params: device dm-2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 9.694730] REISERFS (device dm-2): checking transaction log (dm-2)
[ 9.808607] REISERFS (device dm-2): Using r5 hash to sort names
[ 9.878067] EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
[ 9.909102] EXT4-fs (dm-3): barriers disabled
[ 9.912596] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: nobarrier
[ 9.927252] EXT4-fs (dm-4): barriers disabled
[ 9.939415] EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: nobarrier
[ 9.957582] EXT4-fs (dm-7): barriers disabled
[ 9.959628] EXT4-fs (dm-7): mounted filesystem with writeback data mode. Opts: nobarrier,data=writeback
[ 10.340381] r8169 0000:03:00.0: firmware: agent loaded rtl_nic/rtl8168d-2.fw into memory
[ 10.398755] r8169 0000:03:00.0 eth0: link down
[ 10.398784] r8169 0000:03:00.0 eth0: link down
[ 10.398888] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.750361] r8169 0000:03:00.0 eth0: link up
[ 12.750428] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.766336] RPC: Registered named UNIX socket transport module.
[ 15.766414] RPC: Registered udp transport module.
[ 15.766472] RPC: Registered tcp transport module.
[ 15.766530] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 15.771825] FS-Cache: Loaded
[ 15.772635] Key type dns_resolver registered
[ 15.781818] FS-Cache: Netfs 'nfs' registered for caching
[ 15.791496] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 16.720402] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 16.732925] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.807146] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 16.807760] NFSD: starting 90-second grace period (net ffffffff8166a140)
[ 17.724031] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input21
[ 18.357619] lp: driver loaded but no devices found
[ 18.366478] ppdev: user-space parallel port driver
[ 18.572673] Ebtables v2.0 registered
[ 18.579948] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2398.365988] md: export_rdev(sdb7)
[ 2398.427750] md: bind<sdb7>
[ 2398.436557] RAID1 conf printout:
[ 2398.436563] --- wd:1 rd:2
[ 2398.436568] disk 0, wo:0, o:1, dev:sda1
[ 2398.436573] disk 1, wo:1, o:1, dev:sdb7
[ 2398.436691] md: recovery of RAID array md0
[ 2398.436700] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 2398.436707] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 2398.436714] md: using 128k window, over a total of 18877368k.
[ 2435.557535] md: export_rdev(sdb9)
[ 2435.888079] md: bind<sdb9>
[ 2435.895533] RAID1 conf printout:
[ 2435.895538] --- wd:1 rd:2
[ 2435.895543] disk 0, wo:0, o:1, dev:sda6
[ 2435.895546] disk 1, wo:1, o:1, dev:sdb9
[ 2435.895873] md: delaying recovery of md1 until md0 has finished (they share one or more physical units)
[ 2581.268514] md: md0: recovery done.
[ 2581.286223] md: recovery of RAID array md1
[ 2581.286229] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 2581.286232] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 2581.286237] md: using 128k window, over a total of 31455160k.
[ 2581.412775] RAID1 conf printout:
[ 2581.412782] --- wd:2 rd:2
[ 2581.412788] disk 0, wo:0, o:1, dev:sda1
[ 2581.412792] disk 1, wo:0, o:1, dev:sdb7
[ 3187.131788] md/raid1:md0: Disk failure on sdb7, disabling device.
[ 3187.131788] md/raid1:md0: Operation continuing on 1 devices.
[ 3187.133622] RAID1 conf printout:
[ 3187.133627] --- wd:1 rd:2
[ 3187.133631] disk 0, wo:0, o:1, dev:sda1
[ 3187.133635] disk 1, wo:1, o:0, dev:sdb7
[ 3187.136262] RAID1 conf printout:
[ 3187.136270] --- wd:1 rd:2
[ 3187.136278] disk 0, wo:0, o:1, dev:sda1
[ 3187.483311] md/raid1:md1: Disk failure on sdb9, disabling device.
[ 3187.483311] md/raid1:md1: Operation continuing on 1 devices.
[ 3188.232419] md: md1: recovery done.
[ 3188.236850] RAID1 conf printout:
[ 3188.236855] --- wd:1 rd:2
[ 3188.236860] disk 0, wo:0, o:1, dev:sda6
[ 3188.236863] disk 1, wo:1, o:0, dev:sdb9
[ 3188.236923] RAID1 conf printout:
[ 3188.236927] --- wd:1 rd:2
[ 3188.236931] disk 0, wo:0, o:1, dev:sda6
** Model information
sys_vendor: Gigabyte Technology Co., Ltd.
product_name: P55-UD3
product_version:
chassis_vendor: Gigabyte Technology Co., Ltd.
chassis_version:
bios_vendor: Award Software International, Inc.
bios_version: F9
board_vendor: Gigabyte Technology Co., Ltd.
board_name: P55-UD3
board_version: x.x
** Loaded modules:
ip6table_filter
ip6_tables
ebtable_nat
ebtables
parport_pc
ppdev
lp
parport
xt_tcpudp
xt_conntrack
iptable_nat
nf_nat_ipv4
nf_nat
iptable_filter
ip_tables
x_tables
binfmt_misc
nf_conntrack_ipv4
nf_defrag_ipv4
nf_conntrack
uinput
nfsd
auth_rpcgss
nfs_acl
nfs
lockd
dns_resolver
fscache
sunrpc
reiserfs
dm_crypt
it87
hwmon_vid
bridge
stp
llc
fuse
snd_hda_codec_hdmi
snd_hda_codec_realtek
snd_hda_intel
nvidia(PO)
snd_hda_codec
snd_hwdep
snd_pcm_oss
snd_mixer_oss
snd_pcm
snd_page_alloc
snd_seq_midi
snd_seq_midi_event
synaptics_usb
snd_rawmidi
snd_seq
coretemp
kvm_intel
iTCO_wdt
kvm
iTCO_vendor_support
snd_seq_device
snd_timer
crc32c_intel
snd
pcspkr
evdev
soundcore
lpc_ich
i7core_edac
i2c_i801
mfd_core
edac_core
i2c_core
acpi_cpufreq
mperf
processor
button
thermal_sys
ext4
crc16
jbd2
mbcache
btrfs
zlib_deflate
crc32c
libcrc32c
dm_mod
raid1
md_mod
sr_mod
cdrom
ata_generic
hid_generic
usbhid
hid
sg
sd_mod
crc_t10dif
usb_storage
microcode
ahci
r8169
ehci_pci
libahci
pata_jmicron
mii
libata
uhci_hcd
ehci_hcd
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DMI [8086:d131] (rev 11)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:03.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express Root Port 1 [8086:d138] (rev 11) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f9000000-faffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:08.0 System peripheral [0880]: Intel Corporation Core Processor System Management Registers [8086:d155] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:08.1 System peripheral [0880]: Intel Corporation Core Processor Semaphore and Scratchpad Registers [8086:d156] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:08.2 System peripheral [0880]: Intel Corporation Core Processor System Control and Status Registers [8086:d157] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:08.3 System peripheral [0880]: Intel Corporation Core Processor Miscellaneous Registers [8086:d158] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:10.0 System peripheral [0880]: Intel Corporation Core Processor QPI Link [8086:d150] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:10.1 System peripheral [0880]: Intel Corporation Core Processor QPI Routing and Protocol Registers [8086:d151] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:1a.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b3b] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ff00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b3e] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at fe00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b3f] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at fd00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 05) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbfff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio [8086:3b56] (rev 05)
Subsystem: Giga-byte Technology Device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at fbff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 [8086:3b42] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbe00000-fbefffff
Prefetchable memory behind bridge: 00000000cf800000-00000000cf9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 [8086:3b44] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fbd00000-fbdfffff
Prefetchable memory behind bridge: 00000000fbc00000-00000000fbcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b36] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at fc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b37] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at fb00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b38] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at fa00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB Universal Host Controller [8086:3b39] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at f900 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 05) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 5 Series Chipset LPC Interface Controller [8086:3b02] (rev 05)
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller [8086:3b22] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Device [1458:b005]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 46
Region 0: I/O ports at f800 [size=8]
Region 1: I/O ports at f700 [size=4]
Region 2: I/O ports at f600 [size=8]
Region 3: I/O ports at f500 [size=4]
Region 4: I/O ports at f400 [size=32]
Region 5: Memory at fbffd000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 05)
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbffc000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GT218 [GeForce 210] [10de:0a65] (rev a2) (prog-if 00 [VGA controller])
Subsystem: CardExpert Technology Device [10b0:1401]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at ee000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at cf00 [size=128]
[virtual] Expansion ROM at e0000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nvidia
01:00.1 Audio device [0403]: NVIDIA Corporation High Definition Audio Controller [10de:0be3] (rev a1)
Subsystem: CardExpert Technology Device [10b0:1401]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at faffc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
02:00.0 SATA controller [0106]: JMicron Technology Corp. JMB363 SATA/IDE Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:b000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at fbefe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: ahci
02:00.1 IDE interface [0101]: JMicron Technology Corp. JMB363 SATA/IDE Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at ef00 [size=8]
Region 1: I/O ports at ee00 [size=4]
Region 2: I/O ports at ed00 [size=8]
Region 3: I/O ports at ec00 [size=4]
Region 4: I/O ports at eb00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_jmicron
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03)
Subsystem: Giga-byte Technology GA-EP45-DS5/GA-EG45M-DS2H Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: I/O ports at de00 [size=256]
Region 2: Memory at fbcff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fbcf8000 (64-bit, prefetchable) [size=16K]
[virtual] Expansion ROM at fbc00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
3f:00.0 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture Generic Non-Core Registers [8086:2c51] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:00.1 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture System Address Decoder [8086:2c81] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:02.0 Host bridge [0600]: Intel Corporation Core Processor QPI Link 0 [8086:2c90] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel driver in use: i7core_edac
3f:02.1 Host bridge [0600]: Intel Corporation Core Processor QPI Physical 0 [8086:2c91] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:03.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller [8086:2c98] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:03.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Target Address Decoder [8086:2c99] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:03.4 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Test Registers [8086:2c9c] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:04.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Control Registers [8086:2ca0] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:04.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Address Registers [8086:2ca1] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:04.2 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Rank Registers [8086:2ca2] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:04.3 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers [8086:2ca3] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:05.0 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Control Registers [8086:2ca8] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:05.1 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Address Registers [8086:2ca9] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:05.2 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Rank Registers [8086:2caa] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
3f:05.3 Host bridge [0600]: Intel Corporation Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers [8086:2cab] (rev 04)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
-- System Information:
Debian Release: jessie/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'stable'), (1, 'experimental')
Architecture: i386 (x86_64)
Kernel: Linux 3.8-1-amd64 (SMP w/8 CPU cores)
Locale: LANG=de_DE.utf8, LC_CTYPE=de_DE.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.8-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.50
ii initramfs-tools [linux-initramfs-tool] 0.112
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.8-1-amd64 recommends:
ii firmware-linux-free 3.2
ii libc6-i686 2.17-1
Versions of packages linux-image-3.8-1-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27.1
pn linux-doc-3.8 <none>
Versions of packages linux-image-3.8-1-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.38
ii firmware-linux-nonfree 0.38
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.38
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.8-1-amd64/postinst/missing-firmware-3.8-1-amd64:
linux-image-3.8-1-amd64/prerm/removing-running-kernel-3.8-1-amd64: true
linux-image-3.8-1-amd64/postinst/ignoring-ramdisk:
linux-image-3.8-1-amd64/postinst/depmod-error-initrd-3.8-1-amd64: false
Reply to: