Bug#695995: mpt2sas: port enable failed after reboot when all attached drives are in standby state
Package: linux-2.6
Version: 2.6.32-46
File: mpt2sas
Severity: important
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-46) (dannf@debian.org) (gcc
version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sun Sep 23 10:07:46 UTC 2012
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64
root=UUID=61dd0022-387c-4fb8-9532-a4af17aa4af3 ro clocksource=hpet
hpet=force raid=noautodetect selinux=0 fastboot noisapnp verbose
** Not tainted
** Kernel log:
[ 6.640273] sd 5:0:0:0: [sdf] 4096-byte physical blocks
[ 6.640428] sd 5:0:0:0: [sdf] Write Protect is off
[ 6.640498] sd 5:0:0:0: [sdf] Mode Sense: 00 3a 00 00
[ 6.640549] sd 5:0:0:0: [sdf] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 6.640786] sdf:
[ 6.959380] ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 6.967809] ata7.00: ATA-8: Hitachi HDS5C3020BLE630, MZ4OAAB0, max
UDMA/133
[ 6.967883] ata7.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 6.983299] ata7.00: configured for UDMA/100
[ 6.983554] scsi 6:0:0:0: Direct-Access ATA Hitachi HDS5C302
MZ4O PQ: 0 ANSI: 5
[ 6.983923] sd 6:0:0:0: [sdg] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 6.984014] sd 6:0:0:0: [sdg] 4096-byte physical blocks
[ 6.984205] sd 6:0:0:0: [sdg] Write Protect is off
[ 6.984274] sd 6:0:0:0: [sdg] Mode Sense: 00 3a 00 00
[ 6.984334] sd 6:0:0:0: [sdg] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 6.984677] sdg:
[ 7.302048] ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 7.310495] ata8.00: ATA-8: Hitachi HDS5C3020BLE630, MZ4OAAB0, max
UDMA/133
[ 7.310566] ata8.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 7.327219] ata8.00: configured for UDMA/100
[ 7.327449] scsi 7:0:0:0: Direct-Access ATA Hitachi HDS5C302
MZ4O PQ: 0 ANSI: 5
[ 7.327783] sd 7:0:0:0: [sdh] 3907029168 512-byte logical blocks:
(2.00 TB/1.81 TiB)
[ 7.327879] sd 7:0:0:0: [sdh] 4096-byte physical blocks
[ 7.328061] sd 7:0:0:0: [sdh] Write Protect is off
[ 7.328132] sd 7:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[ 7.328185] sd 7:0:0:0: [sdh] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 7.328503] sdh:
[ 7.435553] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow
Control: None
[ 7.435701] e1000e 0000:03:00.0: eth0: 10/100 speed: disabling TSO
[ 7.437330] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.580591] unknown partition table
[ 12.581039] sd 4:0:0:0: [sde] Attached SCSI disk
[ 12.885658] unknown partition table
[ 12.886229] sd 5:0:0:0: [sdf] Attached SCSI disk
[ 13.256487] unknown partition table
[ 13.256890] sd 6:0:0:0: [sdg] Attached SCSI disk
[ 13.606597] unknown partition table
[ 13.607035] sd 7:0:0:0: [sdh] Attached SCSI disk
[ 13.656764] mpt2sas version 02.100.03.00 loaded
[ 13.657039] scsi8 : Fusion MPT SAS Host
[ 13.657590] mpt2sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[ 13.657677] mpt2sas 0000:01:00.0: setting latency timer to 64
[ 13.657687] mpt2sas0: 64 BIT PCI BUS DMA ADDRESSING SUPPORTED, total
mem (8191048 kB)
[ 13.657894] alloc irq_desc for 30 on node -1
[ 13.657899] alloc kstat_irqs on node -1
[ 13.657912] mpt2sas 0000:01:00.0: irq 30 for MSI/MSI-X
[ 13.657939] mpt2sas0: PCI-MSI-X enabled: IRQ 30
[ 13.658011] mpt2sas0: iomem(0xfad3c000), mapped(0xffffc90000c78000),
size(16384)
[ 13.658099] mpt2sas0: ioport(0xc000), size(256)
[ 13.658167] mpt2sas0: sending diag reset !!
[ 14.777228] mpt2sas0: diag reset: SUCCESS
[ 15.212688] mpt2sas0: Allocated physical memory: size(882 kB)
[ 15.212761] mpt2sas0: Current Controller Queue Depth(361), Max
Controller Queue Depth(1720)
[ 15.212853] mpt2sas0: Scatter Gather Elements per IO(128)
[ 15.445365] mpt2sas0: LSISAS2008: FWVersion(14.00.01.00),
ChipRevision(0x03), BiosVersion(07.27.00.00)
[ 15.445462] mpt2sas0: Protocol=(Initiator),
Capabilities=(Raid,TLR,EEDP,Snapshot Buffer,Diag Trace Buffer,Task Set
Full,NCQ)
[ 15.446128] mpt2sas0: sending port enable !!
[ 16.954511] mpt2sas0: host_add: handle(0x0001),
sas_addr(0x5003048007abbc00), phys(8)
[ 18.139446] eth0: no IPv6 routers present
[ 178.828451] mpt2sas0: expander_add: handle(0x0009), parent(0x0001),
sas_addr(0x50014380182cf0e6), phys(37)
[ 240.375106] INFO: task modprobe:1393 blocked for more than 120 seconds.
[ 240.375179] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs"
disables this message.
[ 240.375270] modprobe D 0000000000000000 0 1393 1266
0x00000000
[ 240.375426] ffff88023f06b880 0000000000000082 0000000000000000
000000000000cc15
[ 240.375674] 0000000000000096 ffffffff8104e54b 000000000000f9e0
ffff88023f0ebfd8
[ 240.375930] 0000000000015780 0000000000015780 ffff88023c4d3880
ffff88023c4d3b78
[ 240.376179] Call Trace:
[ 240.376249] [<ffffffff8104e54b>] ? release_console_sem+0x17e/0x1af
[ 240.376324] [<ffffffff8105aeba>] ? __mod_timer+0x141/0x153
[ 240.376396] [<ffffffff812fbec4>] ? schedule_timeout+0xa5/0xdd
[ 240.376465] [<ffffffff8105aa34>] ? process_timeout+0x0/0x5
[ 240.376536] [<ffffffff812fbd04>] ? wait_for_common+0xde/0x15b
[ 240.376606] [<ffffffff8104a461>] ? default_wake_function+0x0/0x9
[ 240.376686] [<ffffffffa02126e1>] ?
_base_make_ioc_operational+0x929/0xa6f [mpt2sas]
[ 240.376785] [<ffffffffa0214a85>] ? mpt2sas_base_attach+0xb73/0xc61
[mpt2sas]
[ 240.376855] [<ffffffff810412ee>] ? enqueue_task_fair+0x3e/0x82
[ 240.376928] [<ffffffff8103a311>] ? enqueue_task+0x5f/0x68
[ 240.376997] [<ffffffff8103a403>] ? activate_task+0x22/0x28
[ 240.377081] [<ffffffffa0217e21>] ? _scsih_probe+0x32c/0x501 [mpt2sas]
[ 240.377157] [<ffffffff811a2d46>] ? local_pci_probe+0x12/0x16
[ 240.377226] [<ffffffff811a3996>] ? pci_device_probe+0xc0/0xe9
[ 240.377299] [<ffffffff81221520>] ? driver_probe_device+0xa3/0x14b
[ 240.377372] [<ffffffff81221617>] ? __driver_attach+0x4f/0x6f
[ 240.377445] [<ffffffff812215c8>] ? __driver_attach+0x0/0x6f
[ 240.377517] [<ffffffff81220def>] ? bus_for_each_dev+0x43/0x74
[ 240.377588] [<ffffffff812207af>] ? bus_add_driver+0xaf/0x1f8
[ 240.377660] [<ffffffff812218cf>] ? driver_register+0xa7/0x111
[ 240.377735] [<ffffffffa0128000>] ? _scsih_init+0x0/0x112 [mpt2sas]
[ 240.377809] [<ffffffff811a3bdc>] ? __pci_register_driver+0x50/0xb8
[ 240.377888] [<ffffffffa0128000>] ? _scsih_init+0x0/0x112 [mpt2sas]
[ 240.377966] [<ffffffffa01280fc>] ? _scsih_init+0xfc/0x112 [mpt2sas]
[ 240.378041] [<ffffffff8100a065>] ? do_one_initcall+0x64/0x174
[ 240.378114] [<ffffffff8107ab54>] ? sys_init_module+0xc5/0x21a
[ 240.378186] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 314.931549] mpt2sas0: _base_send_port_enable: timeout
[ 314.931620] mpt2sas0: port enable: FAILED
[ 314.931686] mpt2sas0: sending diag reset !!
[ 316.057859] mpt2sas0: diag reset: SUCCESS
[ 316.057969] mpt2sas 0000:01:00.0: PCI INT A disabled
[ 316.058059] mpt2sas0: failure at
/build/buildd-linux-2.6_2.6.32-46-amd64-_ApuPc/linux-2.6-2.6.32/debian/build/source_amd64_none/drivers/scsi/mpt2sas/mpt2sas_scsih.c:6021/_scsih_probe()!
** Model information
sys_vendor: Supermicro
product_name: X8SIE
product_version: 0123456789
chassis_vendor: Supermicro
chassis_version: 0123456789
bios_vendor: American Megatrends Inc.
bios_version: 1.2a
board_vendor: Supermicro
board_name: X8SIE
board_version: 0123456789
** Loaded modules:
Module Size Used by
mpt2sas 87869 0
scsi_transport_sas 19865 1 mpt2sas
sata_sil 7412 0
acpi_cpufreq 5571 1
cpufreq_stats 2740 0
cpufreq_conservative 5162 0
cpufreq_powersave 902 0
cpufreq_userspace 1992 0
uinput 6376 1
w83627ehf 18691 0
hwmon_vid 1828 1 w83627ehf
ipmi_si 30960 0
ipmi_msghandler 26634 1 ipmi_si
loop 11799 0
i2c_i801 7830 0
i2c_core 15819 1 i2c_i801
evdev 7352 4
psmouse 49985 0
joydev 8459 0
snd_pcm 60487 0
snd_timer 15598 1 snd_pcm
snd 46526 2 snd_pcm,snd_timer
soundcore 4598 1 snd
snd_page_alloc 6249 1 snd_pcm
pcspkr 1699 0
serio_raw 3752 0
button 4650 0
processor 29935 5 acpi_cpufreq
ext3 106710 1
jbd 37317 1 ext3
mbcache 5050 1 ext3
sd_mod 29937 2
crc_t10dif 1276 1 sd_mod
usbhid 33292 0
hid 63257 1 usbhid
ata_generic 3239 0
ata_piix 21124 1
libata 133776 3 sata_sil,ata_generic,ata_piix
scsi_mod 126725 4 mpt2sas,scsi_transport_sas,sd_mod,libata
ehci_hcd 32097 0
e1000e 124836 0
usbcore 123271 3 usbhid,ehci_hcd
nls_base 6377 1 usbcore
thermal 11674 0
thermal_sys 11942 2 processor,thermal
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP qlen 1000
link/ether 00:25:90:69:e4:bc brd ff:ff:ff:ff:ff:ff
inet 192.168.254.27/24 brd 192.168.254.255 scope global eth0
inet6 fe80::225:90ff:fe69:e4bc/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes
packets errs drop fifo colls carrier compressed
lo: 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0
eth0: 116405 721 0 0 0 0 0 171
114061 342 0 0 0 0 0 0
*** Protocol statistics:
Ip:
662 total packets received
2 with invalid addresses
0 forwarded
0 incoming packets discarded
519 incoming packets delivered
321 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
3 active connections openings
2 passive connection openings
0 failed connection attempts
0 connection resets received
2 connections established
511 segments received
313 segments send out
0 segments retransmited
0 bad segments received.
1 resets sent
Udp:
8 packets received
0 packets to unknown port received.
0 packet receive errors
8 packets sent
UdpLite:
TcpExt:
1 TCP sockets finished time wait in fast timer
4 delayed acks sent
4 packets directly queued to recvmsg prequeue.
2 bytes directly received in process context from prequeue
12 packet headers predicted
262 acknowledgments not containing data payload received
3 predicted acknowledgments
IpExt:
InOctets: 99693
OutOctets: 107725
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM
Controller [8086:0048] (rev 12)
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:06.0 PCI bridge [0604]: Intel Corporation Core Processor Secondary
PCI Express Root Port [8086:004b] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fad00000-fadfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Intel Corporation Device [8086:0000]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4169
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x8, ASPM L0s L1, Latency L0
<256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive-
BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
00:1a.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series
Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 05) (prog-if 20
[EHCI])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at facfc000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series
Chipset PCI Express Root Port 1 [8086:3b42] (rev 05) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: c0000000-c01fffff
Prefetchable memory behind bridge: 00000000c0200000-00000000c03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0
<256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #2, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4171
Capabilities: [90] Subsystem: Super Micro Computer Inc Device [15d9:040d]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series
Chipset PCI Express Root Port 5 [8086:3b4a] (rev 05) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fae00000-faefffff
Prefetchable memory behind bridge: 00000000c0400000-00000000c05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
<256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4179
Capabilities: [90] Subsystem: Super Micro Computer Inc Device [15d9:040d]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series
Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 05) (prog-if 20
[EHCI])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at facfa000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge
[8086:244e] (rev a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: faf00000-fbffffff
Prefetchable memory behind bridge: 00000000f9000000-00000000f9ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Super Micro Computer Inc Device [15d9:040d]
00:1f.0 ISA bridge [0601]: Intel Corporation 3400 Series Chipset LPC
Interface Controller [8086:3b14] (rev 05)
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=10 <?>
00:1f.2 IDE interface [0101]: Intel Corporation 5 Series/3400 Series
Chipset 4 port SATA IDE Controller [8086:3b20] (rev 05) (prog-if 8f
[Master SecP SecO PriP PriO])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b880 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b480 [size=4]
Region 4: I/O ports at b400 [size=16]
Region 5: I/O ports at b080 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset
SMBus Controller [8086:3b30] (rev 05)
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at facf8000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
00:1f.5 IDE interface [0101]: Intel Corporation 5 Series/3400 Series
Chipset 2 port SATA IDE Controller [8086:3b26] (rev 05) (prog-if 85
[Master SecO PriO])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at ac00 [size=8]
Region 1: I/O ports at a880 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at a480 [size=4]
Region 4: I/O ports at a400 [size=16]
Region 5: I/O ports at a080 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ata_piix
01:00.0 Serial Attached SCSI controller [0107]: LSI Logic / Symbios
Logic SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] [1000:0072] (rev 03)
Subsystem: Super Micro Computer Inc Device [15d9:0400]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at c000 [size=256]
Region 1: Memory at fad3c000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at fad40000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at fad80000 [disabled] [size=512K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Latency L0 <64ns, L1
<1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range BC, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [d0] Vital Product Data
Unknown small resource type 00, will not decode more.
Capabilities: [a8] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c0] MSI-X: Enable- Count=15 Masked-
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003800
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [138 v1] Power Budgeting <?>
Capabilities: [150 v1] Single Root I/O Virtualization (SR-IOV)
IOVCap: Migration-, Interrupt Message Number: 000
IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy-
IOVSta: Migration-
Initial VFs: 16, Total VFs: 16, Number of VFs: 16, Function Dependency
Link: 00
VF offset: 1, stride: 1, Device ID: 0072
Supported Page Size: 00000553, System Page Size: 00000001
Region 0: Memory at 0000000000000000 (64-bit, non-prefetchable)
Region 2: Memory at 0000000000000000 (64-bit, non-prefetchable)
VF Migration: offset: 00000000, BIR: 0
Capabilities: [190 v1] Alternative Routing-ID Interpretation (ARI)
ARICap: MFVC- ACS-, Next Function: 0
ARICtl: MFVC- ACS-, Function Group: 0
03:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit
Network Connection [8086:10d3]
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at faee0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dc00 [size=32]
Region 3: Memory at faedc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
<128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP+ Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-25-90-ff-ff-69-e4-bc
Kernel driver in use: e1000e
04:00.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3114
[SATALink/SATARaid] Serial ATA Controller [1095:3114] (rev 02)
Subsystem: Silicon Image, Inc. Device [1095:7114]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at e480 [size=8]
Region 1: I/O ports at e400 [size=4]
Region 2: I/O ports at ec00 [size=8]
Region 3: I/O ports at e880 [size=4]
Region 4: I/O ports at e800 [size=16]
Region 5: Memory at fbf7fc00 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at fbf80000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sata_sil
04:03.0 VGA compatible controller [0300]: Matrox Graphics, Inc. MGA
G200eW WPCM450 [102b:0532] (rev 0a) (prog-if 00 [VGA controller])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (4000ns min, 8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at f9000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at faffc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at fb000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
** USB devices:
Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0557:2221 ATEN International Co., Ltd
Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.6
APT prefers stable
APT policy: (990, 'stable'), (800, 'testing'), (500,
'stable-updates'), (300, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/4 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration
management sy
ii initramfs-tools [linux-init 0.99~bpo60+1 tools for generating an
initramfs
ii linux-base 3.4~bpo60+1 Linux image base package
ii module-init-tools 3.12-2 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
ii firmware-linux-free 3.1 Binary firmware for various
driver
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64:
false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64:
true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
Reply to: