Bug#684630: linux-image-3.2.0-3-amd64: USB hard disk write speed is slow until I rmmod and modprobe ehci_hcd and uhci_hcd
Package: src:linux
Version: 3.2.21-3
Severity: normal
Dear Maintainer,
My USB hard disk's write speed is slow (about 1MB/s) when I first boot Debian. It speeds up if I issue "rmmod ehci_hcd; rmmod uhci_hcd; modprobe ehci_hcd; modprobe uhci_hcd", to about 26MB/s. I suspect the issue is that uhci_hcd is being used instead of ehci_hcd because it's loaded first during boot, and it's limited to USB 1's maximum of 12Mb/s (which is close to the 1MB/s I was seeing).
I'd expect the system to autodetect whether it can use EHCI and prefer it if possible, or some other behavior more smart than defaulting to UHCI.
This issue recurs after reboot and is consistently reproducible.
-- Package-specific info:
** Version:
Linux version 3.2.0-3-amd64 (Debian 3.2.21-3) (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-8) ) #1 SMP Thu Jun 28 09:07:26 UTC 2012
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-3-amd64 root=UUID=c0888d09-79a8-45ef-a57e-5ad644b6ab12 ro quiet acpi_enforce_resources=lax
** Not tainted
** Kernel log:
[ 427.448087] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 427.448100] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[ 427.448104] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[ 427.448122] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[ 427.448154] uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000cc00
[ 427.448201] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 427.448205] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 427.448209] usb usb5: Product: UHCI Host Controller
[ 427.448211] usb usb5: Manufacturer: Linux 3.2.0-3-amd64 uhci_hcd
[ 427.448214] usb usb5: SerialNumber: 0000:00:1a.2
[ 427.448381] hub 5-0:1.0: USB hub found
[ 427.448387] hub 5-0:1.0: 2 ports detected
[ 427.468064] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 427.468076] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 427.468081] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 427.468095] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[ 427.468125] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000c080
[ 427.468172] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 427.468176] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 427.468179] usb usb6: Product: UHCI Host Controller
[ 427.468182] usb usb6: Manufacturer: Linux 3.2.0-3-amd64 uhci_hcd
[ 427.468185] usb usb6: SerialNumber: 0000:00:1d.0
[ 427.468341] hub 6-0:1.0: USB hub found
[ 427.468347] hub 6-0:1.0: 2 ports detected
[ 427.496061] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 427.496072] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 427.496076] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 427.496091] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[ 427.496126] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000c400
[ 427.496171] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 427.496175] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 427.496178] usb usb7: Product: UHCI Host Controller
[ 427.496181] usb usb7: Manufacturer: Linux 3.2.0-3-amd64 uhci_hcd
[ 427.496184] usb usb7: SerialNumber: 0000:00:1d.1
[ 427.496346] hub 7-0:1.0: USB hub found
[ 427.496352] hub 7-0:1.0: 2 ports detected
[ 427.516058] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 427.516069] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 427.516074] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 427.516092] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[ 427.516122] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000c480
[ 427.516170] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
[ 427.516173] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 427.516177] usb usb8: Product: UHCI Host Controller
[ 427.516180] usb usb8: Manufacturer: Linux 3.2.0-3-amd64 uhci_hcd
[ 427.516182] usb usb8: SerialNumber: 0000:00:1d.2
[ 427.516336] hub 8-0:1.0: USB hub found
[ 427.516342] hub 8-0:1.0: 2 ports detected
[ 427.616029] usb 2-4: new high-speed USB device number 2 using ehci_hcd
[ 427.763708] usb 2-4: New USB device found, idVendor=03f0, idProduct=070c
[ 427.763711] usb 2-4: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 427.763714] usb 2-4: Product: HP Personal Media Drive
[ 427.763716] usb 2-4: Manufacturer: Hewlett-Packard
[ 427.763718] usb 2-4: SerialNumber: ST3320820A5QF5XB5K
[ 427.765455] scsi7 : usb-storage 2-4:1.0
[ 428.192031] usb 8-1: new low-speed USB device number 2 using uhci_hcd
[ 428.374148] usb 8-1: New USB device found, idVendor=045e, idProduct=0040
[ 428.374151] usb 8-1: New USB device strings: Mfr=1, Product=3, SerialNumber=0
[ 428.374154] usb 8-1: Product: Microsoft 3-Button Mouse with IntelliEye(TM)
[ 428.374156] usb 8-1: Manufacturer: Microsoft
[ 428.392509] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:1d.2/usb8/8-1/8-1:1.0/input/input7
[ 428.392775] generic-usb 0003:045E:0040.0003: input,hidraw0: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.2-1/input0
[ 428.632031] usb 8-2: new low-speed USB device number 3 using uhci_hcd
[ 428.767705] scsi 7:0:0:0: Direct-Access ST332082 0AS PQ: 0 ANSI: 2
[ 428.769453] sd 7:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 428.771693] sd 7:0:0:0: [sdb] Write Protect is off
[ 428.771698] sd 7:0:0:0: [sdb] Mode Sense: 38 00 00 00
[ 428.773942] sd 7:0:0:0: [sdb] No Caching mode page present
[ 428.773947] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 428.779568] sd 7:0:0:0: [sdb] No Caching mode page present
[ 428.779572] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 428.809146] usb 8-2: New USB device found, idVendor=046d, idProduct=c312
[ 428.809149] usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 428.809152] usb 8-2: Product: USB Multimedia Keyboard
[ 428.809154] usb 8-2: Manufacturer: LITEON Technology
[ 428.827410] input: LITEON Technology USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1d.2/usb8/8-2/8-2:1.0/input/input8
[ 428.827561] generic-usb 0003:046D:C312.0004: input,hidraw1: USB HID v1.10 Keyboard [LITEON Technology USB Multimedia Keyboard] on usb-0000:00:1d.2-2/input0
[ 429.919450] sdb: sdb1
[ 429.929038] sd 7:0:0:0: [sdb] No Caching mode page present
[ 429.929043] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[ 429.929047] sd 7:0:0:0: [sdb] Attached SCSI disk
[ 449.274714] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: (null)
[ 784.859793] cfg80211: Calling CRDA to update world regulatory domain
[ 785.699217] wlan0: authenticate with 68:7f:74:27:b4:88 (try 1)
[ 785.701215] wlan0: authenticated
[ 785.721314] wlan0: associate with 68:7f:74:27:b4:88 (try 1)
[ 785.723869] wlan0: RX ReassocResp from 68:7f:74:27:b4:88 (capab=0x431 status=0 aid=1)
[ 785.723872] wlan0: associated
[ 1290.871703] cfg80211: Calling CRDA to update world regulatory domain
[ 1291.727156] wlan0: authenticate with 68:7f:74:27:b4:88 (try 1)
[ 1291.729315] wlan0: authenticated
[ 1291.749203] wlan0: associate with 68:7f:74:27:b4:88 (try 1)
[ 1291.751793] wlan0: RX ReassocResp from 68:7f:74:27:b4:88 (capab=0x431 status=0 aid=1)
[ 1291.751796] wlan0: associated
[ 1423.911629] cfg80211: Calling CRDA to update world regulatory domain
[ 1424.751118] wlan0: authenticate with 68:7f:74:27:b4:88 (try 1)
[ 1424.753166] wlan0: authenticated
[ 1424.773085] wlan0: associate with 68:7f:74:27:b4:88 (try 1)
[ 1424.775640] wlan0: RX ReassocResp from 68:7f:74:27:b4:88 (capab=0x431 status=0 aid=1)
[ 1424.775643] wlan0: associated
** Model information
sys_vendor: System manufacturer
product_name: P5K-E
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 1305
board_vendor: ASUSTeK Computer INC.
board_name: P5K-E
board_version: Rev 1.xx
** Loaded modules:
uhci_hcd
usb_storage
ehci_hcd
ip6t_LOG
xt_hl
ip6t_rt
nf_conntrack_ipv6
nf_defrag_ipv6
ipt_REJECT
ipt_LOG
xt_limit
xt_tcpudp
xt_addrtype
xt_state
ip6table_filter
ip6_tables
nf_conntrack_netbios_ns
nf_conntrack_broadcast
nf_nat_ftp
nf_nat
nf_conntrack_ipv4
nf_defrag_ipv4
nf_conntrack_ftp
nf_conntrack
iptable_filter
cryptd
aes_x86_64
aes_generic
ip_tables
x_tables
w83627ehf
hwmon_vid
loop
radeon
ttm
drm_kms_helper
drm
arc4
snd_hda_codec_hdmi
snd_hda_codec_analog
power_supply
i2c_algo_bit
ath9k
ath9k_common
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
acpi_cpufreq
mperf
iTCO_wdt
snd_page_alloc
ath9k_hw
ath
mac80211
cfg80211
rfkill
iTCO_vendor_support
snd_seq
i2c_i801
i2c_core
processor
evdev
snd_seq_device
coretemp
thermal_sys
button
pcspkr
serio_raw
snd_timer
snd
soundcore
ext4
crc16
jbd2
mbcache
sd_mod
sr_mod
crc_t10dif
cdrom
usbhid
hid
uas
ahci
libahci
sky2
libata
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller [8086:29c0] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:8295]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port [8086:29c1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1a.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at c800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at c880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at cc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe8ffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at fe8f8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: f0200000-f05fffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 [8086:294a] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at c080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at c400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at c480 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe8ff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Memory behind bridge: feb00000-febfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IR (ICH9R) LPC Interface Controller [8086:2916] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 44
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b880 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b480 [size=4]
Region 4: I/O ports at b400 [size=32]
Region 5: Memory at fe8fe800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:8277]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe8ff400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RV620 LE [Radeon HD 3450] [1002:95c5] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:01f4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at fe9e0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at d000 [size=256]
[virtual] Expansion ROM at fe900000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
01:00.1 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI RV620 HDMI Audio [Radeon HD 3400 Series] [1002:aa28]
Subsystem: ASUSTeK Computer Inc. Device [1043:aa28]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 46
Region 0: Memory at fe9fc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
02:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8056 PCI-E Gigabit Ethernet Controller [11ab:4364] (rev 12)
Subsystem: ASUSTeK Computer Inc. Device [1043:81f8]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at feafc000 (64-bit, non-prefetchable) [size=16K]
Region 2: I/O ports at e800 [size=256]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: sky2
04:01.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01)
Subsystem: D-Link System Inc DWA-552 802.11n Xtreme N Desktop Adapter (rev A2) [1186:3a7a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at febf0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 03f0:070c Hewlett-Packard
Bus 008 Device 002: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical
Bus 008 Device 003: ID 046d:c312 Logitech, Inc. DeLuxe 250 Keyboard
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-3-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-3-amd64 depends on:
ii debconf [debconf-2.0] 1.5.44
ii initramfs-tools [linux-initramfs-tool] 0.107
ii kmod 8-2
ii linux-base 3.5
ii module-init-tools 8-2
Versions of packages linux-image-3.2.0-3-amd64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-3-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-22.1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-3-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.36
ii firmware-linux-nonfree 0.36
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-3-amd64/postinst/depmod-error-initrd-3.2.0-3-amd64: false
linux-image-3.2.0-3-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-3-amd64/postinst/missing-firmware-3.2.0-3-amd64:
linux-image-3.2.0-3-amd64/prerm/removing-running-kernel-3.2.0-3-amd64: true
Reply to: