Bug#693004: fails to enable USB 3.0 device (external hard drive)
Package: src:linux
Version: 3.2.35-2
Followup-For: Bug #693004
I've got the same problem.
Problem take place for portable usb 3.0 HDD (no external power source). There
are two USB 3.0 ports at my laptop.
There is no problem with USB 2.0 HDD and various USB 1.1 devices (such as
mouse) at the usb 3.0 ports.
When I plug usb 3.0 HDD device, hdd led goes On, after 5-7 sec hdd led goes
Off. Hdd is not mounted.
After that fail, both USB 3.0 ports became completely unusable (until reboot).
I've checked newer kernels for LiveCD (Fedora 17 x32 kernel 3.6.x, OpenSuse
12.2 x64 kernel 3.4.6), USB 3.0 worked fine (average throughput is 50 Mb/s)
Laptop Lenovo Thinkpad Edge 330G (3354-24G), CPU: Pentium B970, chipset: Intel
HM77 Express, IO Controller: Intel Corporation 7 Series/C210 Series Chipset,
In BIOS menu, "USB 3.0 Support=Enabled"
problematic device:
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.35-2
** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-4-amd64 root=UUID=5e0a1d7f-3997-43f1-931f-ce10d19ee440 ro quiet
** Tainted: PCO (5121)
* Proprietary module has been loaded.
* Module from drivers/staging has been loaded.
* Out-of-tree module has been loaded.
** Kernel log:
[ 7.047536] Bad target number (5:0)
[ 7.047784] Bad target number (6:0)
[ 7.047941] Bad target number (7:0)
[ 7.050058] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 7.050158] sd 6:0:0:0: Attached scsi generic sg1 type 0
[ 7.883055] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[ 7.883204] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 7.883469] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 7.883542] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 8.781039] Adding 9764860k swap on /dev/sda5. Priority:-1 extents:1 across:9764860k
[ 8.811262] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 9.424914] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 9.552233] loop: module loaded
[ 10.815125] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[ 10.998562] input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input11
[ 11.783688] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
[ 11.902621] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[ 12.002991] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[ 12.093869] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[ 13.388868] RPC: Registered named UNIX socket transport module.
[ 13.388872] RPC: Registered udp transport module.
[ 13.388874] RPC: Registered tcp transport module.
[ 13.388876] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 13.429655] FS-Cache: Loaded
[ 13.472578] FS-Cache: Netfs 'nfs' registered for caching
[ 13.500993] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 15.945160] vboxdrv: Found 2 processor cores.
[ 15.946109] vboxdrv: fAsync=0 offMin=0x54d offMax=0x313c
[ 15.946248] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 15.946266] vboxdrv: Successfully loaded version 4.1.18_Debian (interface 0x00190000).
[ 16.000623] vboxpci: IOMMU not found (not registered)
[ 16.544256] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input12
[ 19.309152] Bluetooth: Core ver 2.16
[ 19.309178] NET: Registered protocol family 31
[ 19.309181] Bluetooth: HCI device and connection manager initialized
[ 19.309186] Bluetooth: HCI socket layer initialized
[ 19.309188] Bluetooth: L2CAP socket layer initialized
[ 19.309196] Bluetooth: SCO socket layer initialized
[ 19.337300] Bluetooth: RFCOMM TTY layer initialized
[ 19.337306] Bluetooth: RFCOMM socket layer initialized
[ 19.337308] Bluetooth: RFCOMM ver 1.11
[ 19.560095] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 19.560100] Bluetooth: BNEP filters: protocol multicast
[ 20.439879] lp: driver loaded but no devices found
[ 20.746771] ppdev: user-space parallel port driver
[ 20.999181] r8169 0000:08:00.0: firmware: agent loaded rtl_nic/rtl8168e-3.fw into memory
[ 21.095173] r8169 0000:08:00.0: eth0: link down
[ 21.096715] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 53.973304] wlan0: no IPv6 routers present
[ 75.046533] usb 3-4: new high-speed USB device number 2 using xhci_hcd
[ 75.063327] usb 3-4: New USB device found, idVendor=152d, idProduct=2329
[ 75.063332] usb 3-4: New USB device strings: Mfr=1, Product=11, SerialNumber=5
[ 75.063335] usb 3-4: Product: StoreJet Transcend
[ 75.063337] usb 3-4: Manufacturer: JMicron
[ 75.063339] usb 3-4: SerialNumber: 1090439977FF
[ 75.063518] usb 3-4: ep 0x81 - rounding interval to 32768 microframes, ep desc says 0 microframes
[ 75.063523] usb 3-4: ep 0x2 - rounding interval to 32768 microframes, ep desc says 0 microframes
[ 75.276450] Initializing USB Mass Storage driver...
[ 75.276758] scsi7 : usb-storage 3-4:1.0
[ 75.276865] usbcore: registered new interface driver usb-storage
[ 75.276867] USB Mass Storage support registered.
[ 76.274526] scsi 7:0:0:0: Direct-Access StoreJet Transcend PQ: 0 ANSI: 2 CCS
[ 76.275724] sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 76.276542] sd 7:0:0:0: [sdc] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 76.276913] sd 7:0:0:0: [sdc] Write Protect is off
[ 76.276917] sd 7:0:0:0: [sdc] Mode Sense: 34 00 00 00
[ 76.277265] sd 7:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 76.917194] sdc: sdc1
[ 76.919244] sd 7:0:0:0: [sdc] Attached SCSI disk
[ 77.856681] EXT4-fs (sdc1): warning: maximal mount count reached, running e2fsck is recommended
[ 77.857158] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 112.561617] usb 3-4: USB disconnect, device number 2
[ 130.058259] xhci_hcd 0000:00:14.0: Timeout while waiting for address device command
[ 130.262178] xhci_hcd 0000:00:14.0: ERROR no room on ep ring
[ 130.262183] xhci_hcd 0000:00:14.0: ERR: No room for command on command ring
[ 130.466074] usb 4-4: device not accepting address 2, error -12
[ 130.466086] xhci_hcd 0000:00:14.0: ERROR no room on ep ring
[ 130.466088] xhci_hcd 0000:00:14.0: ERR: No room for command on command ring
[ 130.466094] xhci_hcd 0000:00:14.0: ERROR no room on ep ring
[ 130.466096] xhci_hcd 0000:00:14.0: ERR: No room for command on command ring
[ 130.466099] hub 4-0:1.0: couldn't allocate port 4 usb_device
[ 150.631730] xhci_hcd 0000:00:14.0: ERROR no room on ep ring
[ 150.631735] xhci_hcd 0000:00:14.0: ERR: No room for command on command ring
[ 150.631739] hub 3-0:1.0: couldn't allocate port 2 usb_device
[ 196.556250] usb 1-1.2: new low-speed USB device number 4 using ehci_hcd
[ 196.653571] usb 1-1.2: New USB device found, idVendor=0458, idProduct=0037
[ 196.653576] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 196.653579] usb 1-1.2: Product: NetScroll Eye
[ 196.653580] usb 1-1.2: Manufacturer: KYE
[ 196.731667] input: KYE NetScroll Eye as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/input/input13
[ 196.731872] generic-usb 0003:0458:0037.0001: input,hidraw0: USB HID v1.10 Mouse [KYE NetScroll Eye] on usb-0000:00:1a.0-1.2/input0
[ 196.731888] usbcore: registered new interface driver usbhid
[ 196.731889] usbhid: USB HID core driver
[ 199.062923] xhci_hcd 0000:00:14.0: ERROR no room on ep ring
[ 199.062928] xhci_hcd 0000:00:14.0: ERR: No room for command on command ring
[ 199.062932] hub 4-0:1.0: couldn't allocate port 4 usb_device
[ 203.693787] usb 1-1.2: USB disconnect, device number 4
[ 206.059304] xhci_hcd 0000:00:14.0: ERROR no room on ep ring
[ 206.059309] xhci_hcd 0000:00:14.0: ERR: No room for command on command ring
[ 206.059313] hub 4-0:1.0: couldn't allocate port 4 usb_device
** Model information
sys_vendor: LENOVO
product_name: 335424G
product_version: ThinkPad Edge E330
chassis_vendor: LENOVO
chassis_version: Not Available
bios_vendor: LENOVO
bios_version: H3ET65WW(1.02)
board_vendor: LENOVO
board_name: 335424G
board_version: Not Defined
** Loaded modules:
usbhid
hid
usb_storage
parport_pc
ppdev
lp
parport
bnep
rfcomm
bluetooth
pci_stub
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
binfmt_misc
uinput
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
ext2
loop
snd_hda_codec_hdmi
snd_hda_codec_realtek
uvcvideo
videodev
v4l2_compat_ioctl32
media
joydev
lib80211_crypt_tkip
wl(P)
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
snd_page_alloc
i915
drm_kms_helper
drm
thinkpad_acpi
coretemp
iTCO_wdt
iTCO_vendor_support
nvram
rts_pstor(C)
i2c_algo_bit
acpi_cpufreq
snd_seq
mperf
i2c_i801
rfkill
i2c_core
snd_seq_device
crc32c_intel
ghash_clmulni_intel
snd_timer
battery
cryptd
snd
psmouse
serio_raw
evdev
pcspkr
ac
power_supply
video
soundcore
lib80211
wmi
processor
button
ext4
crc16
jbd2
mbcache
sg
sd_mod
crc_t10dif
ahci
libahci
thermal
thermal_sys
r8169
mii
xhci_hcd
libata
ehci_hcd
scsi_mod
usbcore
usb_common
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09)
Subsystem: Lenovo Device [17aa:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0106] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Lenovo Device [17aa:5006]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f0000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 4000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Lenovo Device [17aa:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f1600000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: Lenovo Device [17aa:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f1615000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Lenovo Device [17aa:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f161a000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: Lenovo Device [17aa:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f1610000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: f1500000-f15fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 [8086:1e14] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=07, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: f0d00000-f14fffff
Prefetchable memory behind bridge: 00000000f0400000-00000000f0bfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 4 [8086:1e16] (rev c4) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 00002000-00002fff
Prefetchable memory behind bridge: 00000000f0c00000-00000000f0cfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Lenovo Device [17aa:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f1619000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge [0601]: Intel Corporation HM77 Express Chipset LPC Controller [8086:1e57] (rev 04)
Subsystem: Lenovo Device [17aa:5006]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Lenovo Device [17aa:5006]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 42
Region 0: I/O ports at 4088 [size=8]
Region 1: I/O ports at 409c [size=4]
Region 2: I/O ports at 4080 [size=8]
Region 3: I/O ports at 4098 [size=4]
Region 4: I/O ports at 4060 [size=32]
Region 5: Memory at f1618000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
Subsystem: Lenovo Device [17aa:5006]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f1614000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at efa0 [size=32]
02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01)
Subsystem: Broadcom Corporation Device [14e4:0608]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at f1500000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: wl
03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader [10ec:5209] (rev 01)
Subsystem: Lenovo Device [17aa:5006]
Physical Slot: 1
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0d00000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: rts_pstor
08:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 07)
Subsystem: Lenovo Device [17aa:5006]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at 2000 [size=256]
Region 2: Memory at f0c04000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at f0c00000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 003: ID 5986:0299 Acer, Inc
-- System Information:
Debian Release: 7.0
APT prefers testing
APT policy: (500, 'testing'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-4-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.48
ii initramfs-tools [linux-initramfs-tool] 0.109
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-23.1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
ii firmware-brcm80211 0.36
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.36
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
Reply to: