Bug#693539: mpt2sas: mpt2sas changes SATA drive state from standby to active/idle on temperature read
Package: linux-2.6
Version: 2.6.32-46
Severity: normal
File: mpt2sas
Tags: upstream
SATA drives do wake up when reading temperature using hddtemp.
The issue is not related to:
a. kernel (both 2.6.32 and 3.2.0bpo)
b. hddtemp version (both 0.3-beta15-46 and 0.3-beta15-52)
c. hard drive make and model (both Hitachi and Western Digital)
make the drive to wake up when reading the temperature.
The difference is to which bus/driver the drive is connected to:
I. ata_piix = ok = no drive wake up
II. mpt2sas = not ok = drive wake up
I. $ hdparm -y /dev/sdc && hdparm -C /dev/sdc && hddtemp /dev/sdc && hdparm -C /dev/sdc
/dev/sdc:
issuing standby command
/dev/sdc:
drive state is: standby
/dev/sdc: WDC WD10EARS-00Y5B1: drive is sleeping
/dev/sdc:
drive state is: standby
II. $ hdparm -y /dev/sdd && hdparm -C /dev/sdd && hddtemp /dev/sdd && hdparm -C /dev/sdd
/dev/sdd:
issuing standby command
/dev/sdd:
drive state is: standby
/dev/sdd: WDC WD10EARS-00Y5B1: 38 C
/dev/sdd:
drive state is: active/idle
It doesnâ??t matter whether the drive is connected
III. directly to the controller or
IV. via an expander.
III. $ hdparm -y /dev/sdg && hdparm -C /dev/sdg && hddtemp /dev/sdg && hdparm -C /dev/sdg
/dev/sdg:
issuing standby command
/dev/sdg:
drive state is: standby
/dev/sdg: WDC WD10EARS-00Y5B1: 41 C
/dev/sdg:
drive state is: active/idle
IV. $ hdparm -y /dev/sdn && hdparm -C /dev/sdn && hddtemp /dev/sdn && hdparm -C /dev/sdn
/dev/sdn:
issuing standby command
/dev/sdn:
drive state is: standby
/dev/sdn: WDC WD10EARS-00Y5B1: 42 C
/dev/sdn:
drive state is: active/idle
Also it doesnâ??t matter whether which kernel:
V. Linux debian 3.2.0-0.bpo.3-amd64 #1 SMP Thu Aug 23 07:41:30 UTC 2012 x86_64
VI. Linux debian 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64
is used.
V. $ hdparm -y /dev/sdg && hdparm -C /dev/sdg && hddtemp /dev/sdg && hdparm -C /dev/sdg
/dev/sdg:
issuing standby command
/dev/sdg:
drive state is: standby
/dev/sdg: WDC WD10EARS-00Y5B1: 35 C
/dev/sdg:
drive state is: active/idle
VI. $ hdparm -y /dev/sdn && hdparm -C /dev/sdn && hddtemp /dev/sdn && hdparm -C /dev/sdn
/dev/sdn:
issuing standby command
/dev/sdn:
drive state is: standby
/dev/sdn: WDC WD10EARS-00Y5B1: 42 C
/dev/sdn:
drive state is: active/idle
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-46) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sun Sep 23 10:07:46 UTC 2012
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64 root=UUID=61dd0022-387c-4fb8-9532-a4af17aa4af3 ro clocksource=hpet hpet=force raid=noautodetect selinux=0 fastboot noisapnp quiet
** Not tainted
** Kernel log:
[ 10.225580] scsi 2:0:9:0: Direct-Access ATA WDC WD10EARS-00Y 0A80 PQ: 0 ANSI: 6
[ 10.225588] scsi 2:0:9:0: SATA: handle(0x0012), sas_addr(0x5001438018c7ed1e), device_name(0x50014ee2afb3f64b)
[ 10.225592] scsi 2:0:9:0: SATA: enclosure_logical_id(0x0000000000000000), slot(0)
[ 10.225685] scsi 2:0:9:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 10.225691] scsi 2:0:9:0: qdepth(32), tagged(1), simple(1), ordered(0), scsi_level(7), cmd_que(1)
[ 10.227753] sd 2:0:9:0: [sdm] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 10.227757] sd 2:0:9:0: [sdm] 4096-byte physical blocks
[ 10.228106] sd 2:0:6:0: [sdj] Write Protect is off
[ 10.228111] sd 2:0:6:0: [sdj] Mode Sense: 7f 00 10 08
[ 10.228818] sd 2:0:5:0: [sdi] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 10.229217] scsi 2:0:10:0: Direct-Access ATA WDC WD10EARS-00Y 0A80 PQ: 0 ANSI: 6
[ 10.229225] scsi 2:0:10:0: SATA: handle(0x0013), sas_addr(0x5001438018c7ed1f), device_name(0x50014ee2b0300223)
[ 10.229227] scsi 2:0:10:0: SATA: enclosure_logical_id(0x0000000000000000), slot(0)
[ 10.229317] scsi 2:0:10:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y)
[ 10.229324] scsi 2:0:10:0: qdepth(32), tagged(1), simple(1), ordered(0), scsi_level(7), cmd_que(1)
[ 10.229662] sdd:
[ 10.231017] scsi 2:0:11:0: Enclosure HP HP SAS EXP Card 2.06 PQ: 0 ANSI: 5
[ 10.231021] scsi 2:0:11:0: SSP: handle(0x0014), sas_addr(0x5001438018c7ed25), device_name(0x0000000000000000)
[ 10.231024] scsi 2:0:11:0: SSP: enclosure_logical_id(0x5001438018c7ed25), slot(0)
[ 10.231027] scsi 2:0:11:0: qdepth(254), tagged(1), simple(1), ordered(0), scsi_level(6), cmd_que(1)
[ 10.231081] sd 2:0:10:0: [sdn] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 10.231083] sd 2:0:10:0: [sdn] 4096-byte physical blocks
[ 10.232661] sd 2:0:7:0: [sdk] Write Protect is off
[ 10.232666] sd 2:0:7:0: [sdk] Mode Sense: 7f 00 10 08
[ 10.232847] sd 2:0:6:0: [sdj] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 10.234528] sd 2:0:1:0: [sde] Attached SCSI disk
[ 10.236470] sdf:
[ 10.237417] sd 2:0:7:0: [sdk] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 10.237728] sd 2:0:8:0: [sdl] Write Protect is off
[ 10.237732] sd 2:0:8:0: [sdl] Mode Sense: 7f 00 10 08
[ 10.240223] sdg:
[ 10.241443] sd 2:0:8:0: [sdl] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 10.242537] sdh:
[ 10.243195] sd 2:0:9:0: [sdm] Write Protect is off
[ 10.243199] sd 2:0:9:0: [sdm] Mode Sense: 7f 00 10 08
[ 10.243921] sd 2:0:10:0: [sdn] Write Protect is off
[ 10.243925] sd 2:0:10:0: [sdn] Mode Sense: 7f 00 10 08
[ 10.244221] unknown partition table
[ 10.246913] sd 2:0:9:0: [sdm] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 10.247979] sd 2:0:10:0: [sdn] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 10.248105] sdd1
[ 10.249651] unknown partition table
[ 10.249659] sdi: unknown partition table
[ 10.253944] sdj:
[ 10.257410] sdk:
[ 10.261416] sdl: unknown partition table
[ 10.266497] sdn:
[ 10.267918] sdm:
[ 10.268370] sd 2:0:2:0: [sdf] Attached SCSI disk
[ 10.268439] unknown partition table
[ 10.268829] unknown partition table
[ 10.271904] unknown partition table
[ 10.272145] unknown partition table
[ 10.272280] sd 2:0:0:0: [sdd] Attached SCSI disk
[ 10.273500] sd 2:0:3:0: [sdg] Attached SCSI disk
[ 10.276438] sd 2:0:4:0: [sdh] Attached SCSI disk
[ 10.281264] unknown partition table
[ 10.287234] sd 2:0:5:0: [sdi] Attached SCSI disk
[ 10.291919] sd 2:0:7:0: [sdk] Attached SCSI disk
[ 10.292246] sd 2:0:6:0: [sdj] Attached SCSI disk
[ 10.295360] sd 2:0:8:0: [sdl] Attached SCSI disk
[ 10.296157] sd 2:0:9:0: [sdm] Attached SCSI disk
[ 10.302021] sd 2:0:10:0: [sdn] Attached SCSI disk
[ 10.431360] ses 2:0:11:0: Attached Enclosure device
[ 10.540082] kjournald starting. Commit interval 5 seconds
[ 10.540094] EXT3-fs: mounted filesystem with ordered data mode.
[ 11.276185] udev[641]: starting version 164
[ 11.396363] ACPI: SSDT 00000000bf7b00f0 00E18 (v01 DpgPmm P001Ist 00000011 INTL 20051117)
[ 11.396977] ACPI: SSDT 00000000bf7b0f10 004D5 (v01 PmRef P001Cst 00003001 INTL 20051117)
[ 11.399217] Monitor-Mwait will be used to enter C-1 state
[ 11.399254] Monitor-Mwait will be used to enter C-2 state
[ 11.399279] Monitor-Mwait will be used to enter C-3 state
[ 11.399385] processor LNXCPU:00: registered as cooling_device0
[ 11.404387] processor LNXCPU:01: registered as cooling_device1
[ 11.406173] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
[ 11.406181] ACPI: Power Button [PWRB]
[ 11.417074] processor LNXCPU:02: registered as cooling_device2
[ 11.417158] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[ 11.417165] ACPI: Power Button [PWRF]
[ 11.425404] processor LNXCPU:03: registered as cooling_device3
[ 11.433606] input: PC Speaker as /devices/platform/pcspkr/input/input7
[ 11.453339] alloc irq_desc for 18 on node -1
[ 11.453343] alloc kstat_irqs on node -1
[ 11.453353] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 11.530902] Error: Driver 'pcspkr' is already registered, aborting...
[ 12.203612] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[ 12.204025] EXT3 FS on sdb1, internal journal
[ 12.297725] loop: module loaded
[ 12.312771] ipmi message handler version 39.2
[ 12.314985] IPMI System Interface driver.
[ 12.314990] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0
[ 12.428724] ipmi: Found new BMC (man_id: 0x00b980, prod_id: 0x040d, dev_id: 0x20)
[ 12.428742] IPMI kcs interface initialized
[ 12.464210] w83627ehf: Found W83627DHG chip at 0xa10
[ 13.157646] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.388840] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input8
[ 14.826882] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 14.826887] e1000e 0000:03:00.0: eth0: 10/100 speed: disabling TSO
[ 14.828421] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 25.562984] eth0: no IPv6 routers present
** Model information
sys_vendor: Supermicro
product_name: X8SIE
product_version: 0123456789
chassis_vendor: Supermicro
chassis_version: 0123456789
bios_vendor: American Megatrends Inc.
bios_version: 1.2a
board_vendor: Supermicro
board_name: X8SIE
board_version: 0123456789
** Loaded modules:
Module Size Used by
acpi_cpufreq 5571 1
cpufreq_stats 2740 0
cpufreq_conservative 5162 0
cpufreq_powersave 902 0
cpufreq_userspace 1992 0
uinput 6376 1
w83627ehf 18691 0
hwmon_vid 1828 1 w83627ehf
ipmi_si 30960 0
ipmi_msghandler 26634 1 ipmi_si
loop 11799 0
psmouse 49985 0
snd_pcm 60487 0
evdev 7352 6
serio_raw 3752 0
snd_timer 15598 1 snd_pcm
snd 46526 2 snd_pcm,snd_timer
soundcore 4598 1 snd
snd_page_alloc 6249 1 snd_pcm
i2c_i801 7830 0
i2c_core 15819 1 i2c_i801
pcspkr 1699 0
joydev 8459 0
button 4650 0
processor 29935 5 acpi_cpufreq
ext3 106710 1
jbd 37317 1 ext3
mbcache 5050 1 ext3
ses 5144 0
enclosure 5503 1 ses
hid_apple 4594 0
usbhid 33292 0
hid 63257 2 hid_apple,usbhid
sd_mod 29937 2
crc_t10dif 1276 1 sd_mod
ata_generic 3239 0
mpt2sas 87869 0
ehci_hcd 32097 0
ata_piix 21124 1
scsi_transport_sas 19865 1 mpt2sas
libata 133776 2 ata_generic,ata_piix
usbcore 123271 3 usbhid,ehci_hcd
nls_base 6377 1 usbcore
scsi_mod 126725 5 ses,sd_mod,mpt2sas,scsi_transport_sas,libata
thermal 11674 0
e1000e 124836 0
thermal_sys 11942 2 processor,thermal
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM Controller [8086:0048] (rev 12)
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:06.0 PCI bridge [0604]: Intel Corporation Core Processor Secondary PCI Express Root Port [8086:004b] (rev 12) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fb400000-fb4fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Intel Corporation Device [8086:0000]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4169
Capabilities: [a0] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x8, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot+
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport
00:1a.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 05) (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at fb3fc000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 [8086:3b42] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: c0000000-c01fffff
Prefetchable memory behind bridge: 00000000c0200000-00000000c03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #2, PowerLimit 25.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4171
Capabilities: [90] Subsystem: Super Micro Computer Inc Device [15d9:040d]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 [8086:3b4a] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fb500000-fb5fffff
Prefetchable memory behind bridge: 00000000c0400000-00000000c05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4179
Capabilities: [90] Subsystem: Super Micro Computer Inc Device [15d9:040d]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 [8086:3b4c] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fb600000-fb6fffff
Prefetchable memory behind bridge: 00000000c0600000-00000000c07fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #0, PowerLimit 0.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4181
Capabilities: [90] Subsystem: Super Micro Computer Inc Device [15d9:040d]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 05) (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fb3fa000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: fb700000-fbffffff
Prefetchable memory behind bridge: 00000000fa000000-00000000faffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Super Micro Computer Inc Device [15d9:040d]
00:1f.0 ISA bridge [0601]: Intel Corporation 3400 Series Chipset LPC Interface Controller [8086:3b14] (rev 05)
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=10 <?>
00:1f.2 IDE interface [0101]: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA IDE Controller [8086:3b20] (rev 05) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b880 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b480 [size=4]
Region 4: I/O ports at b400 [size=16]
Region 5: I/O ports at b080 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 05)
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fb3f8000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
00:1f.5 IDE interface [0101]: Intel Corporation 5 Series/3400 Series Chipset 2 port SATA IDE Controller [8086:3b26] (rev 05) (prog-if 85 [Master SecO PriO])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at ac00 [size=8]
Region 1: I/O ports at a880 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at a480 [size=4]
Region 4: I/O ports at a400 [size=16]
Region 5: I/O ports at a080 [size=16]
Capabilities: [70] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ata_piix
01:00.0 Serial Attached SCSI controller [0107]: LSI Logic / Symbios Logic SAS2008 PCI-Express Fusion-MPT SAS-2 [Falcon] [1000:0072] (rev 03)
Subsystem: Super Micro Computer Inc Device [15d9:0400]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at c000 [size=256]
Region 1: Memory at fb43c000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at fb440000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at fb480000 [disabled] [size=512K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range BC, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [d0] Vital Product Data
Unknown small resource type 00, will not decode more.
Capabilities: [a8] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [c0] MSI-X: Enable+ Count=15 Masked-
Vector table: BAR=1 offset=00002000
PBA: BAR=1 offset=00003800
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [138 v1] Power Budgeting <?>
Capabilities: [150 v1] Single Root I/O Virtualization (SR-IOV)
IOVCap: Migration-, Interrupt Message Number: 000
IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy-
IOVSta: Migration-
Initial VFs: 16, Total VFs: 16, Number of VFs: 16, Function Dependency Link: 00
VF offset: 1, stride: 1, Device ID: 0072
Supported Page Size: 00000553, System Page Size: 00000001
Region 0: Memory at 0000000000000000 (64-bit, non-prefetchable)
Region 2: Memory at 0000000000000000 (64-bit, non-prefetchable)
VF Migration: offset: 00000000, BIR: 0
Capabilities: [190 v1] Alternative Routing-ID Interpretation (ARI)
ARICap: MFVC- ACS-, Next Function: 0
ARICtl: MFVC- ACS-, Function Group: 0
Kernel driver in use: mpt2sas
03:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fb5e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dc00 [size=32]
Region 3: Memory at fb5dc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP+ Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-25-90-ff-ff-69-e4-bc
Kernel driver in use: e1000e
04:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fb6e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ec00 [size=32]
Region 3: Memory at fb6dc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP+ BadDLLP- Rollover- Timeout+ NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-25-90-ff-ff-69-e4-bd
Kernel driver in use: e1000e
05:03.0 VGA compatible controller [0300]: Matrox Graphics, Inc. MGA G200eW WPCM450 [102b:0532] (rev 0a) (prog-if 00 [VGA controller])
Subsystem: Super Micro Computer Inc Device [15d9:040d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (4000ns min, 8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at fa000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fb7fc000 (32-bit, non-prefetchable) [size=16K]
Region 2: Memory at fb800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
** USB devices:
Bus 002 Device 004: ID 05ac:0221 Apple, Inc. Aluminum Keyboard (ISO)
Bus 002 Device 003: ID 05ac:1006 Apple, Inc. Hub in Aluminum Keyboard
Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0557:2221 ATEN International Co., Ltd
Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.6
APT prefers stable
APT policy: (990, 'stable'), (500, 'stable-updates'), (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/4 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-init 0.99~bpo60+1 tools for generating an initramfs
ii linux-base 3.4~bpo60+1 Linux image base package
ii module-init-tools 3.12-2 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64: false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64: true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
Reply to: