--- Begin Message ---
- To: submit@bugs.debian.org
- Subject: linux-image-3.2.0-3-686-pae: none
- From: przypadek <przypadek@vp.pl>
- Date: Tue, 28 Aug 2012 13:28:05 +0200
- Message-id: <91028978-5cd352ffbf91bbb4a2350a3fc840757a@pkn6.m5r2.onet>
Package: src:linux
Version: 3.2.0-3-686-pae
Severity: normal
Dear Maintainer,
I have installed linux-image-3.2.0-3-686-pae , xserver-xorg-video-radeon
and all firmware packets
and i had a logs in xorg similar to
(EE) RADEON(0): [dri] RADEONDRIGetVersion failed because of a version
mismatch.
[dri] This chipset requires a kernel module version of 1.17.0,
[dri] but the kernel reports a version of 2.0.0.[dri] If using legacy
modesetting, upgrade your kernel.
[dri] If using kernel modesetting, make sure your module is
[dri] loaded prior to starting X, and that this driver was built
[dri] with support for KMS.
[dri] Disabling DRI
so i found this side http://www.x.org/wiki/radeonBuildHowTo#Troubleshooting
i was trying loaded radeon kernel-module with KMS enabled before X is
started
echo 'GRUB_CMDLINE_LINUX="radeon.modeset=1"' >> /etc/default/grub
but this didn't work
next is that, kernel config needs
CONFIG_FIRMWARE_IN_KERNEL=y
CONFIG_EXTRA_FIRMWARE_DIR="/lib/firmware"
CONFIG_EXTRA_FIRMWARE="radeon/CEDAR_me.bin radeon/CEDAR_pfp.bin
radeon/CEDAR_rlc.bin radeon/CYPRESS_me.bin radeon/CYPRESS_pfp.bin
radeon/CYPRESS_rlc.bin radeon/JUNIPER_me.bin radeon/JUNIPER_pfp.bin
radeon/JUNIPER_rlc.bin radeon/R600_rlc.bin radeon/R700_rlc.bin
radeon/REDWOOD_me.bin radeon/REDWOOD_pfp.bin radeon/REDWOOD_rlc.bin"
i added this and "radeon/RS690_cp.bin", recomplie kernel and it's
working so i think it can be bug
Dawid Juszczyszyn
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** Network interface configuration:
auto lo
iface lo inet loopback
allow-hotplug eth1
iface eth1 inet static
address 192.168.1.2
netmask 255.255.255.0
network 192.168.1.0
broadcast 192.168.1.255
gateway 192.168.1.1
dns-nameservers 85.14.85.2 85.14.85.14
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] nee ATI RS690
Host Bridge [1002:7910]
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI RS690
PCI to PCI Bridge (Internal gfx) [1002:7912] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fde00000-fdffffff
Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:12.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI
SB600 Non-Raid-5 SATA [1002:4380] (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:13.0 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI
SB600 USB (OHCI0) [1002:4387] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI
SB600 USB (OHCI1) [1002:4388] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI
SB600 USB (OHCI2) [1002:4389] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.3 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI
SB600 USB (OHCI3) [1002:438a] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.4 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI
SB600 USB (OHCI4) [1002:438b] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.5 USB controller [0c03]: Advanced Micro Devices [AMD] nee ATI
SB600 USB Controller (EHCI) [1002:4386] (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus
Controller [1002:4385] (rev 14)
Subsystem: Giga-byte Technology GA-MA770-DS3rev2.0 Motherboard
[1458:4385]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 0b00 [size=16]
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: Advanced Micro Devices [AMD] nee ATI SB600
IDE [1002:438c] (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Gigabyte GA-MA69G-S3H Motherboard
[1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f900 [size=16]
Kernel driver in use: pata_atiixp
00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] nee ATI SB600
PCI to LPC Bridge [1002:438d]
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] nee ATI SBx00
PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: fdc00000-fdcfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
01:05.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD]
nee ATI RS690 [Radeon X1200 Series] [1002:791e] (prog-if 00 [VGA
controller])
Subsystem: Giga-byte Technology Device [1458:d001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d8000000 (64-bit, prefetchable) [size=128M]
Region 2: Memory at fdfe0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at ee00 [size=256]
Region 5: Memory at fde00000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: radeon
01:05.2 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI Radeon
X1200 Series Audio Controller [1002:7919]
Subsystem: Giga-byte Technology Device [1458:7919]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 11
Region 0: Memory at fdffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
02:06.0 Ethernet controller [0200]: Marvell Technology Group Ltd.
Marvell W8300 802.11 Adapter [11ab:1fa6] (rev 07)
Subsystem: Global Sun Technology Inc Device [16ab:1fa6]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fddd0000 (32-bit, non-prefetchable) [size=64K]
Region 1: Memory at fdde0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
02:07.0 Multimedia audio controller [0401]: Creative Labs SB Live!
EMU10k1 [1102:0002] (rev 07)
Subsystem: Creative Labs SBLive! 5.1 Model SB0100 [1102:8064]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at df00 [size=32]
Capabilities: <access denied>
Kernel driver in use: snd_emu10k1
02:07.1 Input device controller [0980]: Creative Labs SB Live! Game Port
[1102:7002] (rev 07)
Subsystem: Creative Labs Gameport Joystick [1102:0020]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: I/O ports at de00 [size=8]
Capabilities: <access denied>
02:0f.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10)
Subsystem: Giga-byte Technology GA-MA69G-S3H Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at fddfe000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at fdc00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 09da:000a A4 Tech Co., Ltd Optical Mouse Opto 510D
-- System Information:
Debian Release: wheezy/sid
Architecture: i386 (i686)
Kernel: Linux 3.2.12-686 (SMP w/1 CPU core)
Locale: LANG=pl_PL.UTF-8, LC_CTYPE=pl_PL.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-3-686-pae depends on:
ii debconf [debconf-2.0] 1.5.44
ii initramfs-tools [linux-initramfs-tool] 0.107
ii kmod 8-2
ii linux-base 3.5
ii module-init-tools 9-1
Versions of packages linux-image-3.2.0-3-686-pae recommends:
ii firmware-linux-free 3.1
ii libc6-i686 2.13-35
Versions of packages linux-image-3.2.0-3-686-pae suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-22.1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-3-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.36
ii firmware-linux-nonfree 0.36
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-3-686-pae/postinst/ignoring-ramdisk:
linux-image-3.2.0-3-686-pae/prerm/removing-running-kernel-3.2.0-3-686-pae:
true
linux-image-3.2.0-3-686-pae/postinst/depmod-error-initrd-3.2.0-3-686-pae: false
linux-image-3.2.0-3-686-pae/postinst/missing-firmware-3.2.0-3-686-pae:
--- End Message ---
--- Begin Message ---
- To: przypadek <przypadek@vp.pl>
- Cc: 686080-done@bugs.debian.org
- Subject: Re: radeon: "This chipset requires a kernel module version of 1.17.0"
- From: Jonathan Nieder <jrnieder@gmail.com>
- Date: Fri, 7 Sep 2012 12:11:27 -0700
- Message-id: <20120907191127.GA438@mannheim-rule.local>
- In-reply-to: <503CF8FD.7090009@vp.pl>
- References: <91028978-5cd352ffbf91bbb4a2350a3fc840757a@pkn6.m5r2.onet> <20120828144716.GA927@mannheim-rule.local> <1346165492.2924.737.camel@thor.local> <20120828150330.GA998@mannheim-rule.local> <503CF8FD.7090009@vp.pl>
notfound 686080 linux/3.2.0-3-686-pae
quit
Hi again,
przypadek wrote:
> On 28.08.2012 17:03, Jonathan Nieder wrote:
>> Dawid, could you provide a full kernel log ("dmesg" output) from
>> booting a woorking and a non-working kernel?
[...]
> No I can't, because I checked old kernel, and now is also working
Closing --- I don't want to send you on a wild goose case to track
down what might have been due to missing firmware or something
similar. Sorry for the trouble, and please don't hesitate to let us
know if it happens again.
Thanks for your help and patience.
Sincerely,
Jonathan
--- End Message ---