Bug#683185: linux-image-2.6.32-5-686: On an ASUS P2B-DS adding a USB drive results in "Disabling IRQ#19"
Package: linux-2.6
Version: 2.6.32-45
Severity: important
USB no longer works. It has in the past, it does on the Windows dual-boot.
See the lines in the kernel log including/following "irq 19: nobody cared"
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-45) (dannf@debian.org) (gcc
version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Sun May 6 04:01:19 UTC 2012
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-686
root=UUID=1f8f97d0-8cbd-44aa-9b55-32fdf4787dfa ro
** Not tainted
** Kernel log:
[ 22.203580] mdadm: sending ioctl 1261 to a partition!
[ 22.207054] mdadm: sending ioctl 1261 to a partition!
[ 22.210527] mdadm: sending ioctl 800c0910 to a partition!
[ 22.213566] mdadm: sending ioctl 800c0910 to a partition!
[ 23.591812] md: resync of RAID array md0
[ 23.595104] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 23.598421] md: using maximum available idle IO bandwidth (but not
more than 200000 KB/sec) for resync.
[ 23.601797] md: using 128k window, over a total of 390708736 blocks.
[ 23.605164] md: resuming resync of md0 from checkpoint.
[ 23.736359] sd 4:0:0:0: Attached scsi generic sg3 type 0
[ 23.744732] sd 4:0:1:0: Attached scsi generic sg4 type 0
[ 23.751540] sd 4:0:0:0: [sdc] 143374650 512-byte logical blocks:
(73.4 GB/68.3 GiB)
[ 23.755525] sd 4:0:1:0: [sdd] 71687340 512-byte logical blocks: (36.7
GB/34.1 GiB)
[ 23.761550] sd 4:0:1:0: [sdd] Write Protect is off
[ 23.764888] sd 4:0:1:0: [sdd] Mode Sense: cb 00 00 08
[ 23.768084] sd 4:0:0:0: [sdc] Write Protect is off
[ 23.771036] sr1: scsi-1 drive
[ 23.771551] sr 4:0:4:0: Attached scsi CD-ROM sr1
[ 23.771908] sr 4:0:4:0: Attached scsi generic sg5 type 5
[ 23.776496] sd 4:0:1:0: [sdd] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 23.781280] sd 4:0:0:0: [sdc] Mode Sense: b3 00 00 08
[ 23.783406] sr2: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
[ 23.796378] sr 4:0:5:0: Attached scsi CD-ROM sr2
[ 23.797263] sr 4:0:5:0: Attached scsi generic sg6 type 5
[ 23.798407] sdd:
[ 23.802599] sd 4:0:0:0: [sdc] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 23.811476] sdd1
[ 23.826394] sd 4:0:1:0: [sdd] Attached SCSI disk
[ 23.832482] sdc: sdc1 sdc2 < sdc5 sdc6 >
[ 23.878448] sd 4:0:0:0: [sdc] Attached SCSI disk
[ 24.491740] kjournald starting. Commit interval 5 seconds
[ 24.492079] EXT3 FS on sda1, internal journal
[ 24.492099] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.518702] kjournald starting. Commit interval 5 seconds
[ 24.520311] EXT3 FS on dm-2, internal journal
[ 24.520331] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.552682] kjournald starting. Commit interval 5 seconds
[ 24.556312] EXT3 FS on dm-0, internal journal
[ 24.559703] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.574783] kjournald starting. Commit interval 5 seconds
[ 24.578348] EXT3 FS on dm-1, internal journal
[ 24.581738] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.696447] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
[ 27.274643] fuse init (API version 7.13)
[ 29.917876] Bluetooth: Core ver 2.15
[ 29.921574] NET: Registered protocol family 31
[ 29.924622] Bluetooth: HCI device and connection manager initialized
[ 29.927718] Bluetooth: HCI socket layer initialized
[ 30.114550] Bluetooth: L2CAP ver 2.14
[ 30.117604] Bluetooth: L2CAP socket layer initialized
[ 30.287408] Bluetooth: RFCOMM TTY layer initialized
[ 30.290510] Bluetooth: RFCOMM socket layer initialized
[ 30.293416] Bluetooth: RFCOMM ver 1.11
[ 30.420515] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 30.423838] Bluetooth: BNEP filters: protocol multicast
[ 30.514474] Bridge firewalling registered
[ 30.669746] Bluetooth: SCO (Voice Link) ver 0.6
[ 30.673096] Bluetooth: SCO socket layer initialized
[ 30.807551] eth0: DSPCFG accepted after 0 usec.
[ 30.809008] eth0: link up.
[ 30.809008] eth0: Setting full-duplex based on negotiated link
capability.
[ 31.614982] lp0: using parport0 (interrupt-driven).
[ 31.670345] ppdev: user-space parallel port driver
[ 34.458856] [drm] nouveau 0000:01:00.0: Allocating FIFO number 1
[ 34.476727] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc:
initialised FIFO 1
[ 40.968022] eth0: no IPv6 routers present
[ 4866.716745] eth0: increased tx threshold, txcfg 0xd0f01004.
[ 5719.619788] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga
encoder (output 0)
[ 6415.390685] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on vga
encoder (output 0)
[ 6619.872025] irq 19: nobody cared (try booting with the "irqpoll" option)
[ 6619.874939] Pid: 0, comm: swapper Not tainted 2.6.32-5-686 #1
[ 6619.875878] Call Trace:
[ 6619.875878] [<c106d92d>] ? __report_bad_irq+0x24/0x69
[ 6619.875878] [<c106d934>] ? __report_bad_irq+0x2b/0x69
[ 6619.875878] [<c106da59>] ? note_interrupt+0xe7/0x13e
[ 6619.875878] [<c106df87>] ? handle_fasteoi_irq+0x7a/0x97
[ 6619.875878] [<c1004dd7>] ? handle_irq+0x17/0x1b
[ 6619.875878] [<c1004659>] ? do_IRQ+0x38/0x89
[ 6619.875878] [<c10037f0>] ? common_interrupt+0x30/0x38
[ 6619.875878] [<c112007b>] ? test_cipher+0xf0/0x1ba
[ 6619.875878] [<f7c60447>] ? scsi_request_fn+0x3a9/0x46f [scsi_mod]
[ 6619.875878] [<c1129b3a>] ? __blk_run_queue+0x2e/0x5a
[ 6619.875878] [<c1129bec>] ? blk_run_queue+0x18/0x27
[ 6619.875878] [<f7c5face>] ? scsi_run_queue+0x281/0x308 [scsi_mod]
[ 6619.875878] [<f7c606b5>] ? scsi_next_command+0x25/0x2f [scsi_mod]
[ 6619.875878] [<f7c6101d>] ? scsi_io_completion+0x383/0x3a4 [scsi_mod]
[ 6619.875878] [<f7c5b723>] ? scsi_finish_command+0xaa/0xc2 [scsi_mod]
[ 6619.875878] [<c112cec3>] ? blk_done_softirq+0x53/0x5f
[ 6619.875878] [<c1035a96>] ? __do_softirq+0xaa/0x156
[ 6619.875878] [<c1035b73>] ? do_softirq+0x31/0x3c
[ 6619.875878] [<c1035c4d>] ? irq_exit+0x26/0x58
[ 6619.875878] [<c1004699>] ? do_IRQ+0x78/0x89
[ 6619.875878] [<c10037f0>] ? common_interrupt+0x30/0x38
[ 6619.875878] [<c101aacc>] ? native_safe_halt+0x2/0x3
[ 6619.875878] [<c1008813>] ? default_idle+0x3c/0x5a
[ 6619.875878] [<c1002377>] ? cpu_idle+0x89/0xa2
[ 6619.875878] handlers:
[ 6619.875878] [<f809372c>] (ahc_linux_isr+0x0/0x39 [aic7xxx])
[ 6619.875878] [<f8190ae1>] (irq_handler+0x0/0x35e [firewire_ohci])
[ 6619.875878] Disabling IRQ #19
** Model information
not available
** Loaded modules:
Module Size Used by
ppdev 4058 0
lp 5570 0
sco 5885 2
bridge 33031 0
stp 996 1 bridge
bnep 7452 2
rfcomm 25199 0
l2cap 21721 6 bnep,rfcomm
crc16 1027 1 l2cap
bluetooth 36319 6 sco,bnep,rfcomm,l2cap
rfkill 10264 3 bluetooth
cpufreq_stats 1997 0
cpufreq_powersave 602 0
cpufreq_conservative 4018 0
cpufreq_userspace 1480 0
binfmt_misc 4907 1
fuse 44272 1
nls_utf8 908 1
nls_cp437 4489 1
vfat 6570 1
fat 34912 1 vfat
firewire_sbp2 9647 0
loop 9769 0
snd_emu10k1_synth 4024 0
snd_emux_synth 21906 1 snd_emu10k1_synth
snd_seq_virmidi 2955 1 snd_emux_synth
snd_seq_midi_emul 3554 1 snd_emux_synth
snd_emu10k1 105040 2 snd_emu10k1_synth
snd_seq_midi 3576 0
snd_seq_midi_event 3684 2 snd_seq_virmidi,snd_seq_midi
snd_rawmidi 12513 3 snd_seq_virmidi,snd_emu10k1,snd_seq_midi
ch7006 13868 1
snd_ac97_codec 79152 1 snd_emu10k1
ac97_bus 710 1 snd_ac97_codec
snd_pcm 47222 2 snd_emu10k1,snd_ac97_codec
snd_page_alloc 5045 2 snd_emu10k1,snd_pcm
snd_util_mem 1548 2 snd_emux_synth,snd_emu10k1
snd_hwdep 4054 2 snd_emux_synth,snd_emu10k1
nouveau 314888 2
sg 19937 0
snd_seq 35463 5
snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_midi,snd_seq_midi_event
ttm 33502 1 nouveau
sr_mod 10770 2
snd_timer 12270 3 snd_emu10k1,snd_pcm,snd_seq
snd_seq_device 3673 5
snd_emu10k1_synth,snd_emu10k1,snd_seq_midi,snd_rawmidi,snd_seq
cdrom 26435 1 sr_mod
drm_kms_helper 18569 2 ch7006,nouveau
firewire_ohci 16725 0
drm 112053 5 ch7006,nouveau,ttm,drm_kms_helper
uhci_hcd 16057 0
ehci_hcd 28689 0
i2c_algo_bit 3493 1 nouveau
firewire_core 31243 2 firewire_sbp2,firewire_ohci
snd 34415 12
snd_emux_synth,snd_seq_virmidi,snd_emu10k1,snd_rawmidi,snd_ac97_codec,snd_pcm,snd_hwdep,snd_seq,snd_timer,snd_seq_device
aic7xxx 95151 4
ata_generic 2247 0
parport_pc 15799 1
usbcore 99321 3 uhci_hcd,ehci_hcd
emu10k1_gp 1238 0
shpchp 21200 0
i2c_piix4 7076 0
psmouse 44837 0
floppy 40923 0
parport 22554 3 ppdev,lp,parport_pc
soundcore 3450 1 snd
evdev 5609 7
natsemi 19391 0
button 3598 1 nouveau
processor 26327 0
crc_itu_t 1035 1 firewire_core
pcspkr 1207 0
gameport 6061 2 emu10k1_gp
scsi_transport_spi 14866 1 aic7xxx
serio_raw 2916 0
ata_piix 17736 0
i2c_core 12787 6
ch7006,nouveau,drm_kms_helper,drm,i2c_algo_bit,i2c_piix4
nls_base 4541 5 nls_utf8,nls_cp437,vfat,fat,usbcore
pci_hotplug 18545 1 shpchp
ext3 94396 5
jbd 32401 1 ext3
mbcache 3762 1 ext3
dm_mod 46326 9
raid1 16375 1
md_mod 67429 2 raid1
sd_mod 26013 9
crc_t10dif 1012 1 sd_mod
sata_sil 5620 5
libata 115869 3 ata_generic,ata_piix,sata_sil
thermal 9206 0
scsi_mod 105001 7
firewire_sbp2,sg,sr_mod,aic7xxx,scsi_transport_spi,sd_mod,libata
thermal_sys 9378 2 processor,thermal
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
#NetworkManager#iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP qlen 1000
link/ether 00:02:e3:1e:4d:8a brd ff:ff:ff:ff:ff:ff
inet 10.15.0.83/24 brd 10.15.0.255 scope global eth0
inet6 fe80::202:e3ff:fe1e:4d8a/64 scope link
valid_lft forever preferred_lft forever
3: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
link/ether ba:17:68:7e:06:c3 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed
multicast|bytes packets errs drop fifo colls carrier compressed
lo: 976 12 0 0 0 0 0 0
976 12 0 0 0 0 0 0
eth0:23864380 17150 0 0 0 0 0 0
557386 7373 1 0 1 0 1 0
pan0: 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
16995 total packets received
2 with invalid addresses
0 forwarded
0 incoming packets discarded
16993 incoming packets delivered
7254 requests sent out
16 dropped because of missing route
Icmp:
1 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
echo requests: 1
1 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
echo replies: 1
IcmpMsg:
InType8: 1
OutType0: 1
Tcp:
26 active connections openings
0 passive connection openings
1 failed connection attempts
0 connection resets received
0 connections established
16752 segments received
7019 segments send out
1 segments retransmited
0 bad segments received.
2 resets sent
Udp:
222 packets received
0 packets to unknown port received.
0 packet receive errors
233 packets sent
UdpLite:
TcpExt:
8 TCP sockets finished time wait in fast timer
179 delayed acks sent
15624 packet headers predicted
42 acknowledgments not containing data payload received
504 predicted acknowledgments
1 other TCP timeouts
IpExt:
InMcastPkts: 8
OutMcastPkts: 10
InBcastPkts: 20
InOctets: 23619293
OutOctets: 448535
InMcastOctets: 2135
OutMcastOctets: 2215
InBcastOctets: 4870
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX -
82443BX/ZX/DX Host bridge [8086:7190] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX
AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
Memory behind bridge: e0000000-e1cfffff
Prefetchable memory behind bridge: e1f00000-e3ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:04.0 ISA bridge [0601]: Intel Corporation 82371AB/EB/MB PIIX4 ISA
[8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:04.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE
[8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at d800 [size=16]
Kernel driver in use: ata_piix
00:04.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB
[8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin D routed to IRQ 18
Region 4: I/O ports at d400 [size=32]
Kernel driver in use: uhci_hcd
00:04.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI
[8086:7113] (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin ? routed to IRQ 9
Kernel driver in use: piix4_smbus
00:06.0 SCSI storage controller [0100]: Adaptec AHA-2940U2/U2W /
7890/7891 [9005:001f]
Subsystem: Adaptec 2940U2W SCSI Controller [9005:000f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (9750ns min, 6250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
BIST result: 00
Region 0: I/O ports at d000 [disabled] [size=256]
Region 1: Memory at df800000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 40080000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: aic7xxx
00:09.0 FireWire (IEEE 1394) [0c00]: NEC Corporation IEEE 1394 Host
Controller [1033:00ce] (rev 01) (prog-if 10 [OHCI])
Subsystem: Ratoc System Inc Device [1195:0200]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
00:0a.0 Multimedia audio controller [0401]: Creative Labs SB Live!
EMU10k1 [1102:0002] (rev 04)
Subsystem: Creative Labs CT4620 SBLive! [1102:0021]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at b800 [size=32]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
00:0a.1 Input device controller [0980]: Creative Labs SB Live! Game Port
[1102:7002] (rev 01)
Subsystem: Creative Labs Gameport Joystick [1102:0020]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: I/O ports at b400 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
00:0b.0 RAID bus controller [0104]: Silicon Image, Inc. Adaptec
AAR-1210SA SATA HostRAID Controller [1095:0240] (rev 02) (prog-if 01)
Subsystem: Adaptec Device [9005:0240]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b000 [size=8]
Region 1: I/O ports at a800 [size=4]
Region 2: I/O ports at a400 [size=8]
Region 3: I/O ports at a000 [size=4]
Region 4: I/O ports at 9800 [size=16]
Region 5: Memory at de800000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at 40000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil
00:0c.0 Ethernet controller [0200]: National Semiconductor Corporation
DP83815 (MacPhyter) Ethernet Controller [100b:0020]
Subsystem: Netgear FA311 / FA312 (FA311 with WoL HW) [1385:f311]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2750ns min, 13000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 9400 [size=256]
Region 1: Memory at de000000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 400a0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: natsemi
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV5 [RIVA
TNT2 Ultra] [10de:0029] (rev 11) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. AGP-V3800 Deluxe [1043:0200]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e2000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at e1ff0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: nouveau
** USB devices:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: 6.0.5
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration
management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an
initramfs
ii linux-base 2.6.32-45 Linux image base package
ii module-init-tools 3.12-2+b1 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-45 Binary firmware for various
driver
ii libc6-i686 2.11.3-3 Embedded GNU C Library:
Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
ii grub 0.97-64 GRand Unified Bootloader
(dummy pa
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
* linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
Reply to: