Bug#678461: linux-image-3.0.0-1-amd64: e1000e driver for onboard Intel Corporation
Package: linux-2.6
Version: 3.0.0-3
Severity: normal
..........................................................
Dear Maintainer, Thu Jun 21 07:22:32 PM EDT 2012
Using the driver (# is the superuser prompt):
# ethtool -i eth0
driver: e1000e
version: 1.3.10-k2
firmware-version: 0.13-4
bus-info: 0000:00:19.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no
Without tuning, it drops about 30-50% of packets when pinging
yahoo.com. The following tuning eliminates all packet loss:
# ethtool -G eth0 rx 4096 tx 4096
# ethtool -s eth0 speed 100 duplex full autoneg off
The problem is that this slows down my Internet connection more
than it should. I have nominal dowload speed with RCN cable
of 25 Megabit/sec. Behind my D-Link VWR-VD router my download
speed is at most 7 or 8 Megabit/sec, whereas another computer,
behind the same router, running Fedora 12 actually gets 22
Megabits/sec or even 25 Megabits/sec. In principle, the above
command slows down the Gigabit network adapter in my computer
to 100 Megabits/sec, so I should be able to get around 22
Megabits/sec download speed, which is what RCN guarantees.
(There is no problem with the upload speed; this is a little
over 2 Megabits/sec on both of my computers behind the D-Link
router.) It would be best if the network adapter worked without
any tuning or slowing down, but the packetloss is too high, and
it makes the network virtually unusable.
The rx and tx setting do not seem to make much difference.
Packet loss is avoided even with the settings
# ethtool -G eth0 rx 64 tx 64
# ethtool -s eth0 speed 100 duplex full autoneg off
and different settings of rx and tx do not seem to make
much difference in download speeds.
..........................................................
-- Package-specific info:
** Version:
Linux version 3.0.0-1-amd64 (Debian 3.0.0-3) (ben@decadent.org.uk) (gcc version 4.5.3 (Debian 4.5.3-8) ) #1 SMP Sat Aug 27 16:21:11 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.0.0-1-amd64 root=UUID=9a46da86-1e6f-4a0f-af4e-76bad515efb3 ro quiet
** Tainted: W (512)
* Taint on warning.
** Kernel log:
[ 13.326131] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 13.499231] FS-Cache: Loaded
[ 13.519322] FS-Cache: Netfs 'nfs' registered for caching
[ 13.554739] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 14.148303] fuse init (API version 7.16)
[ 14.353971] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 14.353975] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 14.354396] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.060281] Bluetooth: Core ver 2.16
[ 17.060292] NET: Registered protocol family 31
[ 17.060293] Bluetooth: HCI device and connection manager initialized
[ 17.060295] Bluetooth: HCI socket layer initialized
[ 17.060296] Bluetooth: L2CAP socket layer initialized
[ 17.060324] Bluetooth: SCO socket layer initialized
[ 17.075163] Bluetooth: RFCOMM TTY layer initialized
[ 17.075167] Bluetooth: RFCOMM socket layer initialized
[ 17.075168] Bluetooth: RFCOMM ver 1.11
[ 17.120083] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 17.120085] Bluetooth: BNEP filters: protocol multicast
[ 17.405060] lp: driver loaded but no devices found
[ 17.474111] ppdev: user-space parallel port driver
[ 25.086162] eth0: no IPv6 routers present
[ 100.713780] postgres (2365): /proc/2365/oom_adj is deprecated, please use /proc/2365/oom_score_adj instead.
[ 102.620229] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 102.626680] NFSD: starting 90-second grace period
[ 363.036698] ------------[ cut here ]------------
[ 363.036709] WARNING: at /build/buildd-linux-2.6_3.0.0-3-amd64-9ClimQ/linux-2.6-3.0.0/debian/build/source_amd64_none/net/sched/sch_generic.c:255 dev_watchdog+0xe9/0x148()
[ 363.036715] Hardware name:
[ 363.036719] NETDEV WATCHDOG: eth0 (e1000e): transmit queue 0 timed out
[ 363.036721] Modules linked in: acpi_cpufreq mperf cpufreq_powersave cpufreq_userspace cpufreq_conservative cpufreq_stats parport_pc ppdev lp parport bnep rfcomm bluetooth rfkill binfmt_misc fuse nfsd nfs lockd fscache auth_rpcgss nfs_acl sunrpc loop snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_intel i915 snd_hda_codec snd_hwdep drm_kms_helper snd_pcm snd_seq snd_timer snd_seq_device drm snd i2c_algo_bit iTCO_wdt iTCO_vendor_support i2c_i801 i2c_core video processor soundcore snd_page_alloc shpchp pci_hotplug evdev pcspkr thermal_sys button psmouse serio_raw ext4 mbcache jbd2 crc16 usbhid hid sr_mod cdrom sd_mod crc_t10dif ahci libahci libata xhci_hcd scsi_mod ehci_hcd usbcore e1000e [last unloaded: scsi_wait_scan]
[ 363.036781] Pid: 0, comm: swapper Not tainted 3.0.0-1-amd64 #1
[ 363.036784] Call Trace:
[ 363.036785] <IRQ> [<ffffffff81046521>] ? warn_slowpath_common+0x78/0x8c
[ 363.036797] [<ffffffff810465d6>] ? warn_slowpath_fmt+0x45/0x4a
[ 363.036801] [<ffffffff81014fbc>] ? intel_pmu_enable_all+0x97/0xe7
[ 363.036805] [<ffffffff812953c4>] ? netif_tx_lock+0x43/0x77
[ 363.036811] [<ffffffff8129552d>] ? dev_watchdog+0xe9/0x148
[ 363.036815] [<ffffffff81052b04>] ? run_timer_softirq+0x1bf/0x28a
[ 363.036820] [<ffffffff8104c0ad>] ? raise_softirq_irqoff+0x9/0x2e
[ 363.036823] [<ffffffff81295444>] ? netif_tx_unlock+0x4c/0x4c
[ 363.036828] [<ffffffff81066feb>] ? timekeeping_get_ns+0xd/0x2a
[ 363.036832] [<ffffffff8104bdd4>] ? __do_softirq+0xb9/0x178
[ 363.036837] [<ffffffff8133cf1c>] ? call_softirq+0x1c/0x30
[ 363.036841] [<ffffffff8100a9ef>] ? do_softirq+0x3f/0x84
[ 363.036845] [<ffffffff8104c040>] ? irq_exit+0x3f/0xa3
[ 363.036850] [<ffffffff8101f51e>] ? smp_apic_timer_interrupt+0x76/0x86
[ 363.036855] [<ffffffff8133c6d3>] ? apic_timer_interrupt+0x13/0x20
[ 363.036857] <EOI> [<ffffffff811fcf2c>] ? acpi_hw_read_multiple+0x28/0x60
[ 363.036868] [<ffffffffa01c9400>] ? arch_local_irq_enable+0x4/0x8 [processor]
[ 363.036874] [<ffffffffa01c9fcb>] ? acpi_idle_enter_bm+0x218/0x250 [processor]
[ 363.036879] [<ffffffff812658a4>] ? cpuidle_idle_call+0xf5/0x180
[ 363.036883] [<ffffffff8100827e>] ? cpu_idle+0xa2/0xc4
[ 363.036887] [<ffffffff8169fb65>] ? start_kernel+0x3bd/0x3c8
[ 363.036891] [<ffffffff8169f3c6>] ? x86_64_start_kernel+0x102/0x10f
[ 363.036894] ---[ end trace 06b68da758cb17c1 ]---
[ 364.871703] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 364.871709] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 432.558274] e1000e 0000:00:19.0: eth0: Unsupported Speed/Duplex configuration
[ 462.330742] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 462.330748] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 548.116987] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 548.116995] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 900.964752] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 900.964758] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 1046.870407] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 1046.870413] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 1132.575327] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 1132.575333] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 1264.517783] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None
[ 1264.517789] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[ 1325.986737] usb 3-1.1: new high speed USB device number 5 using ehci_hcd
[ 1326.080178] usb 3-1.1: New USB device found, idVendor=152d, idProduct=2338
[ 1326.080183] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1326.080186] usb 3-1.1: Product: USB to ATA/ATAPI Bridge
[ 1326.080189] usb 3-1.1: Manufacturer: JMicron
[ 1326.080191] usb 3-1.1: SerialNumber: 222296760966
[ 1326.164077] usbcore: registered new interface driver uas
[ 1326.179994] Initializing USB Mass Storage driver...
[ 1326.180280] scsi6 : usb-storage 3-1.1:1.0
[ 1326.180515] usbcore: registered new interface driver usb-storage
[ 1326.180518] USB Mass Storage support registered.
[ 1327.175892] scsi 6:0:0:0: Direct-Access ST350041 8AS PQ: 0 ANSI: 2 CCS
[ 1327.280538] sd 6:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 1327.281263] sd 6:0:0:0: [sdc] Write Protect is off
[ 1327.281268] sd 6:0:0:0: [sdc] Mode Sense: 00 38 00 00
[ 1327.282509] sd 6:0:0:0: [sdc] Asking for cache data failed
[ 1327.282515] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 1327.284846] sd 6:0:0:0: [sdc] Asking for cache data failed
[ 1327.284850] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 1327.347315] sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 >
[ 1327.352637] sd 6:0:0:0: [sdc] Asking for cache data failed
[ 1327.352653] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 1327.352657] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 2015.322762] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 2015.381341] EXT4-fs (sdc2): mounted filesystem with ordered data mode. Opts: (null)
[ 2015.477708] EXT4-fs (sdc3): mounted filesystem with ordered data mode. Opts: (null)
[ 2015.545810] EXT4-fs (sdc5): mounted filesystem with ordered data mode. Opts: (null)
[ 2015.597457] EXT4-fs (sdc6): mounted filesystem with ordered data mode. Opts: (null)
[ 2015.698277] EXT4-fs (sdc7): mounted filesystem with ordered data mode. Opts: (null)
[ 2239.546603] usb 3-1.1: USB disconnect, device number 5
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: Intel Corp.
bios_version: BLH6710H.86A.0125.2011.0705.1517
board_vendor: Intel Corporation
board_name: DH67BL
board_version: AAG10189-207
** Loaded modules:
Module Size Used by
usb_storage 47996 0
uas 13299 0
acpi_cpufreq 13009 1
mperf 12453 1 acpi_cpufreq
cpufreq_powersave 12454 0
cpufreq_userspace 12576 0
cpufreq_conservative 13147 0
cpufreq_stats 12862 0
parport_pc 22395 0
ppdev 12763 0
lp 17270 0
parport 31929 3 parport_pc,ppdev,lp
bnep 17615 2
rfcomm 33848 0
bluetooth 114376 10 bnep,rfcomm
rfkill 19080 2 bluetooth
binfmt_misc 13040 1
fuse 66430 1
nfsd 260662 13
nfs 259369 0
lockd 71503 2 nfsd,nfs
fscache 36721 1 nfs
auth_rpcgss 37204 2 nfsd,nfs
nfs_acl 12511 2 nfsd,nfs
sunrpc 172969 19 nfsd,nfs,lockd,auth_rpcgss,nfs_acl
loop 22711 0
snd_hda_codec_hdmi 26321 1
snd_hda_codec_realtek 278027 1
snd_hda_intel 26140 2
i915 342883 2
snd_hda_codec 72699 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 13186 1 snd_hda_codec
drm_kms_helper 27216 1 i915
snd_pcm 68104 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
snd_seq 45208 0
snd_timer 22581 2 snd_pcm,snd_seq
snd_seq_device 13137 1 snd_seq
drm 163280 3 i915,drm_kms_helper
snd 52823 13 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
i2c_algo_bit 12850 1 i915
iTCO_wdt 17081 0
iTCO_vendor_support 12704 1 iTCO_wdt
i2c_i801 16870 0
i2c_core 23909 5 i915,drm_kms_helper,drm,i2c_algo_bit,i2c_i801
video 17707 1 i915
processor 27942 5 acpi_cpufreq
soundcore 13152 1 snd
snd_page_alloc 13043 2 snd_hda_intel,snd_pcm
shpchp 31343 0
pci_hotplug 27232 1 shpchp
evdev 17558 11
pcspkr 12579 0
thermal_sys 17949 2 video,processor
button 12930 1 i915
psmouse 55656 0
serio_raw 12846 0
ext4 313917 12
mbcache 13066 1 ext4
jbd2 62574 1 ext4
crc16 12343 2 bluetooth,ext4
usbhid 40516 0
hid 73172 1 usbhid
sr_mod 21811 0
cdrom 35093 1 sr_mod
sd_mod 36259 18
crc_t10dif 12348 1 sd_mod
ahci 25089 16
libahci 22767 1 ahci
libata 149043 2 ahci,libahci
xhci_hcd 68261 0
scsi_mod 162442 5 usb_storage,uas,sr_mod,sd_mod,libata
ehci_hcd 40090 0
usbcore 128338 6 usb_storage,uas,usbhid,xhci_hcd,ehci_hcd
e1000e 124997 0
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
# iface eth0 inet dhcp
iface eth0 inet static
address 192.168.15.20
netmask 255.255.255.0
network 192.168.15.0
broadcast 192.168.15.255
gateway 192.168.15.1
# dns-* options are implemented by the resolvconf package, if installed
dns-nameservers 207.172.3.11
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether e0:69:95:d7:80:74 brd ff:ff:ff:ff:ff:ff
inet 192.168.15.20/24 brd 192.168.15.255 scope global eth0
inet6 fe80::e269:95ff:fed7:8074/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 1047286 5760 0 0 0 0 0 0 1047286 5760 0 0 0 0 0 0
eth0: 177996158 293304 7509 0 0 7509 0 22 332498941 375736 0 0 0 0 0 0
*** Protocol statistics:
Ip:
291829 total packets received
0 forwarded
0 incoming packets discarded
291829 incoming packets delivered
207316 requests sent out
Icmp:
251 ICMP messages received
2 input ICMP message failed.
ICMP input histogram:
destination unreachable: 144
echo replies: 107
310 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 138
echo request: 172
IcmpMsg:
InType0: 107
InType3: 144
OutType3: 138
OutType8: 172
Tcp:
3983 active connections openings
9 passive connection openings
109 failed connection attempts
15 connection resets received
0 connections established
285640 segments received
374355 segments send out
588 segments retransmited
0 bad segments received.
125 resets sent
Udp:
5882 packets received
132 packets to unknown port received.
0 packet receive errors
6018 packets sent
UdpLite:
TcpExt:
3070 TCP sockets finished time wait in fast timer
2 packets rejects in established connections because of timestamp
416 delayed acks sent
1 delayed acks further delayed because of locked socket
Quick ack mode was activated 93 times
24 packets directly queued to recvmsg prequeue.
24 bytes directly received in process context from prequeue
140869 packet headers predicted
5085 acknowledgments not containing data payload received
175268 predicted acknowledgments
1 congestion windows recovered without slow start by DSACK
16 congestion windows recovered without slow start after partial ack
161 other TCP timeouts
95 DSACKs sent for old packets
4 DSACKs sent for out of order packets
5 DSACKs received
22 connections reset due to unexpected data
7 connections reset due to early user close
2 connections aborted due to timeout
TCPDSACKIgnoredOld: 3
TCPSackShiftFallback: 35
IpExt:
InMcastPkts: 63
OutMcastPkts: 43
InBcastPkts: 88
OutBcastPkts: 88
InOctets: 173408358
OutOctets: 317692751
InMcastOctets: 9370
OutMcastOctets: 4922
InBcastOctets: 14828
OutBcastOctets: 14828
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0100] (rev 09)
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0102] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at fe000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fe529000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:19.0 Ethernet controller [0200]: Intel Corporation 82579V Gigabit Network Connection [8086:1503] (rev 05)
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 42
Region 0: Memory at fe500000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fe528000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe527000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 50
Region 0: Memory at fe520000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: fe400000-fe4fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe526000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge [0601]: Intel Corporation H67 Express Chipset Family LPC Controller [8086:1c4a] (rev 05)
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 RAID bus controller [0104]: Intel Corporation 82801 SATA Controller [RAID mode] [8086:2822] (rev 05)
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 48
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at fe525000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe524000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
01:00.0 PCI bridge [0604]: Integrated Technology Express, Inc. Device [1283:8892] (rev 10) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=02, subordinate=02, sec-latency=32
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
03:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) (prog-if 30 [XHCI])
Subsystem: Intel Corporation Device [8086:2002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fe400000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 003: ID 046d:c055 Logitech, Inc.
Bus 003 Device 004: ID 04d9:1503 Holtek Semiconductor, Inc. Shortboard Lefty
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.0.0-1-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.0.0-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.43
ii initramfs-tools [linux-initramfs-tool] 0.106
ii linux-base 3.5
ii module-init-tools 3.16-1
Versions of packages linux-image-3.0.0-1-amd64 recommends:
pn firmware-linux-free <none>
Versions of packages linux-image-3.0.0-1-amd64 suggests:
ii grub-pc 1.99-22
pn linux-doc-3.0.0 <none>
Versions of packages linux-image-3.0.0-1-amd64 is related to:
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.0.0-1-amd64/postinst/ignoring-ramdisk:
linux-image-3.0.0-1-amd64/prerm/removing-running-kernel-3.0.0-1-amd64: true
linux-image-3.0.0-1-amd64/postinst/missing-firmware-3.0.0-1-amd64:
linux-image-3.0.0-1-amd64/postinst/depmod-error-initrd-3.0.0-1-amd64: false
Sincerely yours,
Attila Mate
mate@sci.brooklyn.cuny.edu
http://www.sci.brooklyn.cuny.edu/~mate/
Home phone: (212)929-0966
Reply to: