--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.24-etchnhalf.1-686: RAID1 broken after upgrading kernel to 2.6.24-etchnhalf
- From: Olaf Zaplinski <oz@tuxfriends.net>
- Date: Fri, 31 Oct 2008 18:43:41 +0100
- Message-id: <20081031174341.3817.63703.reportbug@binky.tuxfriends.net>
Package: linux-image-2.6.24-etchnhalf.1-686
Version: 2.6.24-6~etchnhalf.6
Severity: grave
Justification: causes non-serious data loss
upgraded from 2.6.18 to 2.6.24-etchnhalf on i686 machine, afterwards all my RAID1 volumes were broken:
Personalities : [raid1]
md3 : active raid1 hda6[0]
1100352 blocks [2/1] [U_]
md2 : active raid1 hda5[0]
1060160 blocks [2/1] [U_]
md1 : active raid1 hda2[0]
1959808 blocks [2/1] [U_]
md0 : active raid1 hda1[0]
40064 blocks [2/1] [U_]
Reason: /dev/hda is running fine (PIIX4), but /dev/sda on 53c875 is missing in the RAID setup.
It is accessible:
binky:~# fdisk -l /dev/sda
Disk /dev/sda: 4335 MB, 4335206400 bytes
255 heads, 63 sectors/track, 527 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
[--snip--]
but the RAID setup is broken.
-- Package-specific info:
** Version:
Linux version 2.6.24-etchnhalf.1-686 (Debian 2.6.24-6~etchnhalf.6) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Oct 13 07:27:05 UTC 2008
** Command line:
auto BOOT_IMAGE=Linux ro root=901 lapic reboot=warm
** Not tainted
** Kernel log:
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 12, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hda: max request size: 128KiB
hda: 8467200 sectors (4335 MB) w/96KiB Cache, CHS=8400/16/63
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
scsi 0:0:0:0: Direct-Access IBM DCAS-34330W S65A PQ: 0 ANSI: 2
target0:0:0: tagged command queuing enabled, command queue depth 16.
target0:0:0: Beginning Domain Validation
target0:0:0: asynchronous
target0:0:0: wide asynchronous
target0:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15)
target0:0:0: Domain Validation skipping write tests
target0:0:0: Ending Domain Validation
scsi 0:0:2:0: Sequential-Access TANDBERG SLR6 0404 PQ: 0 ANSI: 2
target0:0:2: Beginning Domain Validation
target0:0:2: asynchronous
target0:0:2: wide asynchronous
target0:0:2: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns, offset 15)
target0:0:2: Domain Validation skipping write tests
target0:0:2: Ending Domain Validation
Probing IDE interface ide1...
md: raid1 personality registered for level 1
md: md0 stopped.
md: bind<hda1>
raid1: raid set md0 active with 1 out of 2 mirrors
md: md1 stopped.
md: bind<hda2>
raid1: raid set md1 active with 1 out of 2 mirrors
md: md2 stopped.
md: bind<hda5>
raid1: raid set md2 active with 1 out of 2 mirrors
md: md3 stopped.
md: bind<hda6>
raid1: raid set md3 active with 1 out of 2 mirrors
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
st: Version 20070203, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
st 0:0:2:0: Attached scsi tape st0
st 0:0:2:0: st0: try direct i/o: yes (alignment 512 B)
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 8467200 512-byte hardware sectors (4335 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: b3 00 00 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 8467200 512-byte hardware sectors (4335 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: b3 00 00 08
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
Driver 'osst' needs updating - please use bus_type methods
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input0
Linux agpgart interface v0.102
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xd0000000
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
parport_pc 00:0a: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
input: Power Button (FF) as /class/input/input1
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input2
ACPI: Power Button (CM) [PWRB]
Adding 72284k swap on /dev/hda3. Priority:42 extents:1 across:72284k
Adding 72284k swap on /dev/sda3. Priority:42 extents:1 across:72284k
EXT3 FS on md1, internal journal
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Filesystem "md2": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md2
Ending clean XFS mount for filesystem: md2
Filesystem "md3": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md3
Ending clean XFS mount for filesystem: md3
eth0: CSR0 00008000
eth0: Setting full-duplex based on MII#1 link partner capability of 01e1.
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
iptables/ssh-in IN=eth0 OUT= MAC=00:c0:f0:4e:d8:9d:00:90:69:89:fc:1f:08:00 SRC=212.105.192.13 DST=62.206.102.82 LEN=60 TOS=0x00 PREC=0x00 TTL=63 ID=56530 DF PROTO=TCP SPT=37732 DPT=22 WINDOW=5840 RES=0x00 CWR ECE SYN URGP=0
iptables/ssh-in IN=eth0 OUT= MAC=00:c0:f0:4e:d8:9d:00:90:69:89:fc:1f:08:00 SRC=212.105.192.13 DST=62.206.102.82 LEN=60 TOS=0x00 PREC=0x00 TTL=63 ID=9961 DF PROTO=TCP SPT=37744 DPT=22 WINDOW=5840 RES=0x00 CWR ECE SYN URGP=0
iptables/ssh-in IN=eth0 OUT= MAC=00:c0:f0:4e:d8:9d:00:90:69:89:fc:1f:08:00 SRC=212.105.192.13 DST=62.206.102.82 LEN=60 TOS=0x00 PREC=0x00 TTL=63 ID=64753 DF PROTO=TCP SPT=37746 DPT=22 WINDOW=5840 RES=0x00 CWR ECE SYN URGP=0
** Loaded modules:
Module Size Used by
nf_conntrack_ftp 9056 0
ipt_recent 8984 2
xt_state 2528 3
xt_multiport 3200 2
xt_pkttype 1984 2
nf_conntrack_ipv4 17544 6
xt_conntrack 2880 3
nf_conntrack 62656 4 nf_conntrack_ftp,xt_state,nf_conntrack_ipv4,xt_conntrack
xt_tcpudp 3264 31
ipt_REJECT 4608 12
ipt_LOG 6176 4
xt_limit 2720 3
iptable_filter 3040 1
ip_tables 13316 1 iptable_filter
x_tables 14372 10 ipt_recent,xt_state,xt_multiport,xt_pkttype,xt_conntrack,xt_tcpudp,ipt_REJECT,ipt_LOG,xt_limit,ip_tables
ac 6212 0
xfs 505880 2
dm_snapshot 17060 0
dm_mirror 21792 0
dm_mod 56004 2 dm_snapshot,dm_mirror
eeprom 7312 0
lm78 16568 0
hwmon_vid 3104 1 lm78
evdev 11200 0
button 8528 0
parport_pc 26340 0
parport 34472 1 parport_pc
rtc_cmos 8384 0
rtc_core 18152 1 rtc_cmos
rtc_lib 3104 1 rtc_core
i2c_piix4 8556 0
intel_agp 23540 1
agpgart 31912 1 intel_agp
i2c_core 22656 3 eeprom,lm78,i2c_piix4
pcspkr 3264 0
shpchp 31220 0
pci_hotplug 27840 1 shpchp
osst 49820 0
sd_mod 27296 2
st 35676 0
ext3 123272 2
jbd 43892 1 ext3
mbcache 8480 1 ext3
raid1 22336 4
md_mod 73652 5 raid1
ide_generic 1280 0 [permanent]
ide_disk 15776 6
uhci_hcd 23568 0
tulip 49792 0
usbcore 127724 2 uhci_hcd
piix 7556 0 [permanent]
generic 4484 0 [permanent]
ide_core 108740 4 ide_generic,ide_disk,piix,generic
ata_generic 7556 0
libata 144560 1 ata_generic
thermal 16092 0
processor 36840 2 thermal
fan 4868 0
sym53c8xx 69876 1
scsi_transport_spi 22976 1 sym53c8xx
scsi_mod 141516 6 osst,sd_mod,st,libata,sym53c8xx,scsi_transport_spi
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge [8086:7190] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: d4000000-d5ffffff
Prefetchable memory behind bridge: d6000000-d6ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
00:07.0 ISA bridge [0601]: Intel Corporation 82371AB/EB/MB PIIX4 ISA [8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE [8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
00:07.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB [8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin D routed to IRQ 12
Region 4: I/O ports at e000 [size=32]
00:07.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113] (rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:0b.0 Ethernet controller [0200]: Lite-On Communications Inc LNE100TX [11ad:0002] (rev 20)
Subsystem: Kingston Technologies Unknown device [2646:f002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e400 [size=256]
Region 1: Memory at d8000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 20000000 [disabled] [size=256K]
00:0d.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic 53c875 [1000:000f] (rev 03)
Subsystem: Tekram Technology Co.,Ltd. DC390F/U Ultra Wide SCSI Adapter [1de1:3904]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4250ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at d8001000 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at d8002000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 20040000 [disabled] [size=64K]
01:00.0 VGA compatible controller [0300]: NVidia / SGS Thomson (Joint Venture) Riva128 [12d2:0018] (rev 22) (prog-if 00 [VGA])
Subsystem: Elsa AG Unknown device [1048:0c15]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d6000000 (32-bit, prefetchable) [size=16M]
[virtual] Expansion ROM at d5000000 [disabled] [size=4M]
Capabilities: <access denied>
-- System Information:
Debian Release: 4.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.24-etchnhalf.1-686
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Versions of packages linux-image-2.6.24-etchnhalf.1-686 depends on:
ii debconf [debconf-2.0] 1.5.11etch2 Debian configuration management sy
ii initramfs-tools [linux-initr 0.85i tools for generating an initramfs
ii module-init-tools 3.3-pre4-2 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.24-etchnhalf.1-686 recommends:
ii libc6-i686 2.3.6.ds1-13etch7 GNU C Library: Shared libraries [i
-- debconf information:
linux-image-2.6.24-etchnhalf.1-686/preinst/bootloader-initrd-2.6.24-etchnhalf.1-686: true
linux-image-2.6.24-etchnhalf.1-686/preinst/elilo-initrd-2.6.24-etchnhalf.1-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-etchnhalf.1-686/preinst/abort-overwrite-2.6.24-etchnhalf.1-686:
linux-image-2.6.24-etchnhalf.1-686/postinst/depmod-error-2.6.24-etchnhalf.1-686: false
linux-image-2.6.24-etchnhalf.1-686/postinst/old-dir-initrd-link-2.6.24-etchnhalf.1-686: true
linux-image-2.6.24-etchnhalf.1-686/prerm/would-invalidate-boot-loader-2.6.24-etchnhalf.1-686: true
linux-image-2.6.24-etchnhalf.1-686/preinst/overwriting-modules-2.6.24-etchnhalf.1-686: true
linux-image-2.6.24-etchnhalf.1-686/preinst/initrd-2.6.24-etchnhalf.1-686:
linux-image-2.6.24-etchnhalf.1-686/postinst/old-system-map-link-2.6.24-etchnhalf.1-686: true
linux-image-2.6.24-etchnhalf.1-686/postinst/depmod-error-initrd-2.6.24-etchnhalf.1-686: false
linux-image-2.6.24-etchnhalf.1-686/preinst/lilo-initrd-2.6.24-etchnhalf.1-686: true
linux-image-2.6.24-etchnhalf.1-686/postinst/kimage-is-a-directory:
linux-image-2.6.24-etchnhalf.1-686/preinst/abort-install-2.6.24-etchnhalf.1-686:
linux-image-2.6.24-etchnhalf.1-686/prerm/removing-running-kernel-2.6.24-etchnhalf.1-686: true
linux-image-2.6.24-etchnhalf.1-686/preinst/failed-to-move-modules-2.6.24-etchnhalf.1-686:
linux-image-2.6.24-etchnhalf.1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.24-etchnhalf.1-686/postinst/bootloader-error-2.6.24-etchnhalf.1-686:
linux-image-2.6.24-etchnhalf.1-686/postinst/bootloader-test-error-2.6.24-etchnhalf.1-686:
linux-image-2.6.24-etchnhalf.1-686/postinst/old-initrd-link-2.6.24-etchnhalf.1-686: true
linux-image-2.6.24-etchnhalf.1-686/postinst/create-kimage-link-2.6.24-etchnhalf.1-686: true
--- End Message ---