Bug#669006: linux-image-3.2.0-2-486: ata_piix poor performance on ich5
Package: linux-2.6
Version: 3.2.12-1
Severity: normal
Dear Maintainer,
I recently updated my home server from squeeze to wheezy, in order to get
the most out of my vdr and possibly able to record hdtv channels.
Kernel had to be updated to 3.2-series because there is a newer api
for vdr.
At first I noticed that NFS performance is low when tried to access this
server, and any serious reading attempt leads nfsd consuming all the
available cpu time. Later it became obvious that the local filesystem
is to blame, it behaves like there is no DMA.
However...
sudo hdparm -i /dev/sda
/dev/sda:
Model=WDC WD5000AACS-00G8B1, FwRev=05.04C05, SerialNo=WD-WCAUK0320827
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50
BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976773168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7
* signifies the current active mode
sudo hdparm -i /dev/sdb
/dev/sdb:
Model=WDC WD5000AAKS-00YGA0, FwRev=12.01C02, SerialNo=WD-WMAS80005202
Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50
BuffType=unknown, BuffSize=16384kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=976773168
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6
AdvancedPM=no WriteCache=enabled
Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7
* signifies the current active mode
So, it is a mirrored root-raid setup.
Already tried adding ide0=noprobe and ide1=noprobe, and changed sata setup
in the bios from "auto" to "enhanced", with no noticeable difference
in the performance.
I think this is relevant from lshw output:
description: Desktop Computer
width: 32 bits
*-core
description: Motherboard
product: IS7-E2 (Intel i865-ICH5)
vendor: http://www.abit.com.tw/
physical id: 0
version: 1.0
*-firmware
description: BIOS
vendor: Phoenix Technologies, LTD
physical id: 0
version: 6.00 PG
date: 06/01/2004
size: 128KiB
capacity: 448KiB
capabilities: isa pci pnp apm upgrade shadowing cdboot bootselect socketedrom edd int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb agp ls120boot zipboot
*-cpu
description: CPU
product: Intel(R) Celeron(R) CPU 2.00GHz
vendor: Intel Corp.
physical id: 4
bus info: cpu@0
version: 15.2.9
slot: Socket 478
size: 2040MHz
capacity: 4GHz
width: 32 bits
clock: 102MHz
capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs bts cid xtpr
configuration: id=0
*-ide
description: IDE interface
product: 82801EB (ICH5) SATA Controller
vendor: Intel Corporation
physical id: 1f.2
bus info: pci@0000:00:1f.2
logical name: scsi0
logical name: scsi1
version: 02
width: 32 bits
clock: 66MHz
capabilities: ide bus_master emulated
configuration: driver=ata_piix latency=0
resources: irq:18 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:f000(size=16)
*-disk:0
description: ATA Disk
product: WDC WD5000AACS-0
vendor: Western Digital
physical id: 1
bus info: scsi@1:0.0.0
logical name: /dev/sda
version: 05.0
serial: WD-WCAUK0320827
size: 465GiB (500GB)
capabilities: partitioned partitioned:dos
configuration: ansiversion=5 signature=6ad47105
*-volume
description: EXT3 volume
vendor: Linux
physical id: 1
bus info: scsi@1:0.0.0,1
logical name: /dev/sda1
version: 1.0
serial: 533cb95c-a4c1-4426-9fd9-7581feca3b3d
size: 465GiB
capacity: 465GiB
capabilities: primary bootable multi journaled extended_attributes large_files recover ext3 ext2 initialized
configuration: created=2009-06-24 16:04:13 filesystem=ext3 modified=2012-03-29 12:14:23 mounted=2012-04-15 21:53:10 state=clean
*-disk:1
description: ATA Disk
product: WDC WD5000AAKS-0
vendor: Western Digital
physical id: 0.1.0
bus info: scsi@1:0.1.0
logical name: /dev/sdb
version: 12.0
serial: WD-WMAS80005202
size: 465GiB (500GB)
capabilities: partitioned partitioned:dos
configuration: ansiversion=5 signature=0006622a
*-volume
description: EXT3 volume
vendor: Linux
physical id: 1
bus info: scsi@1:0.1.0,1
logical name: /dev/sdb1
version: 1.0
serial: 533cb95c-a4c1-4426-9fd9-7581feca3b3d
size: 465GiB
capacity: 465GiB
capabilities: primary bootable multi journaled extended_attributes large_files recover ext3 ext2 initialized
configuration: created=2009-06-24 16:04:13 filesystem=ext3 modified=2012-03-29 12:14:23 mounted=2012-04-15 21:53:10 state=clean
-- Package-specific info:
** Version:
Linux version 3.2.0-2-486 (Debian 3.2.12-1) (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-1) ) #1 Tue Mar 20 18:45:21 UTC 2012
** Command line:
BOOT_IMAGE=debian3.2.0 ro root=900 ide0=noprobe ide1=noprobe
** Not tainted
** Kernel log:
[64227.677467] IN=eth0 OUT= MAC=00:50:8d:61:a2:14:6c:50:4d:7b:8f:42:08:00 SRC=89.217.72.92 DST=89.106.45.179 LEN=60 TOS=0x00 PREC=0x00 TTL=51 ID=864 DF PROTO=TCP SPT=60392 DPT=23 WINDOW=5840 RES=0x00 SYN URGP=0
[64234.868211] IN=eth0 OUT= MAC=00:50:8d:61:a2:14:6c:50:4d:7b:8f:42:08:00 SRC=66.220.153.72 DST=89.106.45.179 LEN=1500 TOS=0x00 PREC=0x00 TTL=83 ID=9232 DF PROTO=TCP SPT=443 DPT=50590 WINDOW=18 RES=0x00 ACK URGP=0
** Model information
not available
** Loaded modules:
dvb_ttpci
budget_ci
sg
binfmt_misc
ppdev
lp
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
tun
mperf
speedstep_lib
cpufreq_powersave
cpufreq_conservative
cpufreq_userspace
cpufreq_stats
ipt_MASQUERADE
xt_limit
xt_tcpudp
xt_state
ipt_REJECT
ipt_LOG
iptable_nat
nf_nat
nf_conntrack_ipv4
nf_defrag_ipv4
iptable_mangle
iptable_filter
nf_conntrack_ftp
nf_conntrack
ip_tables
x_tables
fuse
hwmon_vid
firewire_sbp2
firewire_core
crc_itu_t
loop
usblp
rc_tt_1500
stv0297
usbhid
hid
usb_storage
uas
ir_lirc_codec
lirc_dev
budget_core
radeon
ir_mce_kbd_decoder
ir_sony_decoder
ttm
drm_kms_helper
ir_jvc_decoder
ttpci_eeprom
r8169
8139too
8139cp
drm
sr_mod
ir_rc6_decoder
saa7146_vv
ir_rc5_decoder
saa7146
ir_nec_decoder
dvb_core
videobuf_dma_sg
videobuf_core
iTCO_wdt
cdrom
iTCO_vendor_support
pcspkr
videodev
mii
uhci_hcd
i2c_algo_bit
media
ehci_hcd
rc_core
rng_core
i2c_i801
evdev
usbcore
i2c_core
serio_raw
usb_common
shpchp
floppy
parport_pc
parport
processor
button
ext3
mbcache
jbd
raid1
md_mod
sd_mod
crc_t10dif
ata_generic
ata_piix
libata
scsi_mod
fan
thermal
thermal_sys
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02)
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P AGP Bridge [8086:2571] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: f8000000-f9ffffff
Prefetchable memory behind bridge: e8000000-f7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface [8086:2576] (rev 02)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at fecf0000 (32-bit, non-prefetchable) [size=4K]
00:1d.0 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at bc00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at b000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 [8086:24d7] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at b400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02) (prog-if 00 [UHCI])
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at b800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02) (prog-if 20 [EHCI])
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fa000000-fbffffff
Prefetchable memory behind bridge: 80000000-800fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller [8086:24d1] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f000 [size=16]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02)
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RV280 [Radeon 9200 PRO] [1002:5960] (rev 01) (prog-if 00 [VGA controller])
Subsystem: C.P. Technology Co. Ltd Device [148c:2094]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at f9000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at f8000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
01:00.1 Display controller [0380]: Advanced Micro Devices [AMD] nee ATI RV280 [Radeon 9200 PRO] (Secondary) [1002:5940] (rev 01)
Subsystem: C.P. Technology Co. Ltd Device [148c:2095]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at f0000000 (32-bit, prefetchable) [disabled] [size=128M]
Region 1: Memory at f9010000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: <access denied>
02:02.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: ABIT Computer Corp. Device [147b:1033]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 80020000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: 8139too
02:04.0 Multimedia controller [0480]: Philips Semiconductors SAA7146 [1131:7146] (rev 01)
Subsystem: Technotrend Systemtechnik GmbH DVB C-1500 [13c2:1010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fb001000 (32-bit, non-prefetchable) [size=512]
Kernel driver in use: budget_ci dvb
02:05.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8169/8110 Family PCI Gigabit Ethernet NIC [10ec:8169]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at a400 [size=256]
Region 1: Memory at fb002000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at 80000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
02:06.0 Multimedia controller [0480]: Philips Semiconductors SAA7146 [1131:7146] (rev 01)
Subsystem: Technotrend Systemtechnik GmbH Octal/Technotrend DVB-C for iTV [13c2:000a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fb003000 (32-bit, non-prefetchable) [size=512]
Kernel driver in use: av7110
** Sound cards:
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-2-486
Locale: LANG=en_DK, LC_CTYPE=fi_FI@euro (charmap=ISO-8859-15)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-3.2.0-2-486 depends on:
ii debconf [debconf-2.0] 1.5.42
ii initramfs-tools [linux-initramfs-tool] 0.101
ii kmod 6-2
ii linux-base 3.5
ii module-init-tools 6-2
Versions of packages linux-image-3.2.0-2-486 recommends:
ii firmware-linux-free 3
Versions of packages linux-image-3.2.0-2-486 suggests:
pn lilo 1:23.2-3
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-2-486 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree 0.35
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf-show failed
--
Teemu Järvinen
Reply to: