The first cabinet has five partitions, each on their own LUN. Four of
the partitions are over 2TB, with the fifth being around 250GB. The second and third cabinets are single
partition volumes of approx 12TB each. All were formatted ext3, and later upgraded to ext4. The error messages and volume corruption occurs under heavy disk I/O *ONLY* to the volumes greater than 2TB. The system will operate fine with heavy
I/O on the sub-2TB partitions, and will not trigger an error.
Here is a select entry from the syslog: (This is the first sign of trouble)
Jan 25 16:00:59 mahoney kernel: [423913.010689] mptscsih: ioc2: attempting task abort! (sc=ffff880114134b00)
Jan 25 16:00:59 mahoney kernel: [423913.010694] sd 6:0:0:4: [sdf] CDB: Write(10): 2a 00 6e 44 12 02 00 04 00 00
Jan 25 16:01:09 mahoney kernel: [423923.310034] mptscsih: ioc2: WARNING - Issuing Reset from mptscsih_IssueTaskMgmt!!
Jan 25 16:01:09 mahoney kernel: [423923.310040] mptbase: ioc2: Initiating recovery
Jan 25 16:01:10 Received SCSI Bus Reset event at the SCSI Bus 1
Jan 25 16:01:18 mahoney kernel: [423931.870063] mptscsih: ioc2: task abort: SUCCESS (rv=2002) (sc=ffff880114134b00) (sn=2400569)
Jan 25 16:01:18 mahoney kernel: [423932.290037] scsi target6:0:0: Beginning Domain Validation
Jan 25 16:01:18 mahoney kernel: [423932.293490] scsi target6:0:0: Domain Validation skipping write tests
Jan 25 16:01:18 mahoney kernel: [423932.293492] scsi target6:0:0: Ending Domain Validation
Jan 25 16:01:18 mahoney kernel: [423932.293580] scsi target6:0:0: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 127)
Jan 25 16:01:18 mahoney kernel: [423932.500055] scsi target6:0:0: Beginning Domain Validation
Jan 25 16:01:18 mahoney kernel: [423932.503513] scsi target6:0:0: Domain Validation skipping write tests
Jan 25 16:01:18 mahoney kernel: [423932.503515] scsi target6:0:0: Ending Domain Validation
Jan 25 16:01:18 mahoney kernel: [423932.503598] scsi target6:0:0: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 127)
Jan 25 16:01:19 mahoney kernel: [423932.710053] scsi target6:0:0: Beginning Domain Validation
Jan 25 16:01:19 mahoney kernel: [423932.713494] scsi target6:0:0: Domain Validation skipping write tests
Jan 25 16:01:19 mahoney kernel: [423932.713496] scsi target6:0:0: Ending Domain Validation
Jan 25 16:01:19 mahoney kernel: [423932.713587] scsi target6:0:0: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 127)
Jan 25 16:01:19 mahoney kernel: [423932.920052] scsi target6:0:0: Beginning Domain Validation
Jan 25 16:01:19 mahoney kernel: [423932.923506] scsi target6:0:0: Domain Validation skipping write tests
Jan 25 16:01:19 mahoney kernel: [423932.923509] scsi target6:0:0: Ending Domain Validation
Jan 25 16:01:19 mahoney kernel: [423932.923604] scsi target6:0:0: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 127)
Jan 25 16:01:19 mahoney kernel: [423933.130037] scsi target6:0:0: Beginning Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.133500] scsi target6:0:0: Domain Validation skipping write tests
Jan 25 16:01:19 mahoney kernel: [423933.133502] scsi target6:0:0: Ending Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.133591] scsi target6:0:0: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 127)
Jan 25 16:01:19 mahoney kernel: [423933.340053] scsi target6:0:0: Beginning Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.343338] scsi target6:0:0: Domain Validation skipping write tests
Jan 25 16:01:19 mahoney kernel: [423933.343340] scsi target6:0:0: Ending Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.343431] scsi target6:0:0: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 127)
Jan 25 16:01:19 mahoney kernel: [423933.343492] scsi target6:0:3: Beginning Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.360207] scsi target6:0:3: Domain Validation skipping write tests
Jan 25 16:01:19 mahoney kernel: [423933.360210] scsi target6:0:3: Ending Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.360271] scsi target6:0:3: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 127)
Jan 25 16:01:19 mahoney kernel: [423933.360331] scsi target6:0:3: Beginning Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.363595] scsi target6:0:3: Domain Validation skipping write tests
Jan 25 16:01:19 mahoney kernel: [423933.363598] scsi target6:0:3: Ending Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.363659] scsi target6:0:3: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 127)
Jan 25 16:01:19 mahoney kernel: [423933.363720] scsi target4:0:2: Beginning Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.370252] scsi target4:0:2: Ending Domain Validation
Jan 25 16:01:19 mahoney kernel: [423933.370361] scsi target4:0:2: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP (6.25 ns, offset 127)
Then some time later, errors like these are bound to show up....
Jan 25 16:40:54 mahoney kernel: [426307.674562] Errataon LSI53C1030 occurred.sc->req_bufflen=0x21000,xfer_cnt=0x00
Any light that you could shed on the
situation would be greatly appreciated. Thank you for your time.
-Glen
Bootlog and lspci output follows:
Jan 25 18:34:14 mahoney kernel: imklog 4.2.0, log source = /proc/kmsg started.
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Initializing cgroup subsys cpuset
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Initializing cgroup subsys cpu
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Linux version 2.6.32-37-server (buildd@allspice) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #81-Ubuntu SMP Fri Dec 2 20:49:12 UTC 2011 (Ubuntu 2.6.32-37.81-server 2.6.32.49+drm33.21)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-37-server root=UUID=f26d6825-9f3d-405e-921e-08d4925b769e ro quiet
Jan 25 18:34:14 mahoney kernel: [ 0.000000] KERNEL supported cpus:
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Intel GenuineIntel
Jan 25 18:34:14 mahoney kernel: [ 0.000000] AMD AuthenticAMD
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Centaur CentaurHauls
Jan 25 18:34:14 mahoney kernel: [ 0.000000] BIOS-provided physical RAM map:
Jan 25 18:34:14 mahoney kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000cffa8000 (usable)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] BIOS-e820: 00000000cffa8000 - 00000000cffb7c00 (ACPI data)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] BIOS-e820: 00000000cffb7c00 - 00000000d0000000 (reserved)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] BIOS-e820: 00000000fe000000 - 0000000100000000 (reserved)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] DMI 2.4 present.
Jan 25 18:34:14 mahoney kernel: [ 0.000000] last_pfn = 0x130000 max_arch_pfn = 0x400000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Jan 25 18:34:14 mahoney kernel: [ 0.000000] last_pfn = 0xcffa8 max_arch_pfn = 0x400000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Scanning 1 areas for low memory corruption
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified physical RAM map:
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 0000000000000000 - 0000000000001000 (usable)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 0000000000001000 - 0000000000006000 (reserved)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 0000000000006000 - 00000000000a0000 (usable)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 0000000000100000 - 00000000cffa8000 (usable)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 00000000cffa8000 - 00000000cffb7c00 (ACPI data)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 00000000cffb7c00 - 00000000d0000000 (reserved)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 00000000e0000000 - 00000000f0000000 (reserved)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 00000000fe000000 - 0000000100000000 (reserved)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] modified: 0000000100000000 - 0000000130000000 (usable)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] init_memory_mapping: 0000000000000000-00000000cffa8000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] NX (Execute Disable) protection: active
Jan 25 18:34:14 mahoney kernel: [ 0.000000] init_memory_mapping: 0000000100000000-0000000130000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] NX (Execute Disable) protection: active
Jan 25 18:34:14 mahoney kernel: [ 0.000000] RAMDISK: 3773f000 - 37fefa91
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: RSDP 00000000000f2620 00024 (v02 DELL )
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: XSDT 00000000000f26a0 0004C (v01 DELL PE_SC3 00000001 DELL 00000001)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: FACP 00000000000f27a8 000F4 (v03 DELL PE_SC3 00000001 DELL 00000001)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: DSDT 00000000cffa8000 03C53 (v01 DELL PE_SC3 00000001 MSFT 0100000E)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: FACS 00000000cffb7c00 00040
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: APIC 00000000000f289c 000C8 (v01 DELL PE_SC3 00000001 DELL 00000001)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: SPCR 00000000000f297d 00050 (v01 DELL PE_SC3 00000001 DELL 00000001)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: HPET 00000000000f29cd 00038 (v01 DELL PE_SC3 00000001 DELL 00000001)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: MCFG 00000000000f2a05 0003C (v01 DELL PE_SC3 00000001 DELL 00000001)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] No NUMA configuration found
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Faking a node at 0000000000000000-0000000130000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Bootmem setup node 0 0000000000000000-0000000130000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] NODE_DATA [000000000000d000 - 0000000000012fff]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] bootmap [0000000000013000 - 0000000000038fff] pages 26
Jan 25 18:34:14 mahoney kernel: [ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 0130000000]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] #2 [0001000000 - 0001a84544] TEXT DATA BSS ==> [0001000000 - 0001a84544]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] #3 [003773f000 - 0037fefa91] RAMDISK ==> [003773f000 - 0037fefa91]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] #4 [000009e000 - 0000100000] BIOS reserved ==> [000009e000 - 0000100000]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] #5 [0001a85000 - 0001a85234] BRK ==> [0001a85000 - 0001a85234]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] #6 [0000008000 - 000000c000] PGTABLE ==> [0000008000 - 000000c000]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] #7 [000000c000 - 000000d000] PGTABLE ==> [000000c000 - 000000d000]
Jan 25 18:34:14 mahoney kernel: [ 0.000000] found SMP MP-table at [ffff8800000fe710] fe710
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Zone PFN ranges:
Jan 25 18:34:14 mahoney kernel: [ 0.000000] DMA 0x00000000 -> 0x00001000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] DMA32 0x00001000 -> 0x00100000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Normal 0x00100000 -> 0x00130000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Movable zone start PFN for each node
Jan 25 18:34:14 mahoney kernel: [ 0.000000] early_node_map[4] active PFN ranges
Jan 25 18:34:14 mahoney kernel: [ 0.000000] 0: 0x00000000 -> 0x00000001
Jan 25 18:34:14 mahoney kernel: [ 0.000000] 0: 0x00000006 -> 0x000000a0
Jan 25 18:34:14 mahoney kernel: [ 0.000000] 0: 0x00000100 -> 0x000cffa8
Jan 25 18:34:14 mahoney kernel: [ 0.000000] 0: 0x00100000 -> 0x00130000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x808
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x12] disabled)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x13] disabled)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x14] disabled)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x15] disabled)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x16] disabled)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x17] disabled)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec81000] gsi_base[64])
Jan 25 18:34:14 mahoney kernel: [ 0.000000] IOAPIC[1]: apic_id 3, version 32, address 0xfec81000, GSI 64-87
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information
Jan 25 18:34:14 mahoney kernel: [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] SMP: Allowing 8 CPUs, 6 hotplug CPUs
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 0000000000001000 - 0000000000006000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 0000000000100000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 00000000cffa8000 - 00000000cffb7000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 00000000cffb7000 - 00000000cffb8000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 00000000cffb8000 - 00000000d0000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 00000000d0000000 - 00000000e0000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fe000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PM: Registered nosave memory: 00000000fe000000 - 0000000100000000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Allocating PCI resources starting at d0000000 (gap: d0000000:10000000)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Booting paravirtualized kernel on bare hardware
Jan 25 18:34:14 mahoney kernel: [ 0.000000] NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880005800000 s92376 r8192 d22312 u262144
Jan 25 18:34:14 mahoney kernel: [ 0.000000] pcpu-alloc: s92376 r8192 d22312 u262144 alloc=1*2097152
Jan 25 18:34:14 mahoney kernel: [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1031257
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Policy zone: Normal
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-37-server root=UUID=f26d6825-9f3d-405e-921e-08d4925b769e ro quiet
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Initializing CPU#0
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Checking aperture...
Jan 25 18:34:14 mahoney kernel: [ 0.000000] No AGP bridge found
Jan 25 18:34:14 mahoney kernel: [ 0.000000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Placing 64MB software IO TLB between ffff8800059de000 - ffff8800099de000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] software IO TLB at phys 0x59de000 - 0x99de000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Memory: 4047132k/4980736k available (5515k kernel code, 787188k absent, 146416k reserved, 3117k data, 812k init)
Jan 25 18:34:14 mahoney kernel: [ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Hierarchical RCU implementation.
Jan 25 18:34:14 mahoney kernel: [ 0.000000] NR_IRQS:4352 nr_irqs:1560
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Extended CMOS year: 2000
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Console: colour VGA+ 80x25
Jan 25 18:34:14 mahoney kernel: [ 0.000000] console [tty0] enabled
Jan 25 18:34:14 mahoney kernel: [ 0.000000] allocated 41943040 bytes of page_cgroup
Jan 25 18:34:14 mahoney kernel: [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Fast TSC calibration using PIT
Jan 25 18:34:14 mahoney kernel: [ 0.000000] Detected 2992.259 MHz processor.
Jan 25 18:34:14 mahoney kernel: [ 0.010006] Calibrating delay loop (skipped), value calculated using timer frequency.. 5984.51 BogoMIPS (lpj=29922590)
Jan 25 18:34:14 mahoney kernel: [ 0.010030] Security Framework initialized
Jan 25 18:34:14 mahoney kernel: [ 0.010050] AppArmor: AppArmor initialized
Jan 25 18:34:14 mahoney kernel: [ 0.010357] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Jan 25 18:34:14 mahoney kernel: [ 0.012411] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Jan 25 18:34:14 mahoney kernel: [ 0.013390] Mount-cache hash table entries: 256
Jan 25 18:34:14 mahoney kernel: [ 0.013541] Initializing cgroup subsys ns
Jan 25 18:34:14 mahoney kernel: [ 0.013546] Initializing cgroup subsys cpuacct
Jan 25 18:34:14 mahoney kernel: [ 0.013550] Initializing cgroup subsys memory
Jan 25 18:34:14 mahoney kernel: [ 0.013557] Initializing cgroup subsys devices
Jan 25 18:34:14 mahoney kernel: [ 0.013559] Initializing cgroup subsys freezer
Jan 25 18:34:14 mahoney kernel: [ 0.013561] Initializing cgroup subsys net_cls
Jan 25 18:34:14 mahoney kernel: [ 0.013580] CPU: L1 I cache: 32K, L1 D cache: 32K
Jan 25 18:34:14 mahoney kernel: [ 0.013582] CPU: L2 cache: 4096K
Jan 25 18:34:14 mahoney kernel: [ 0.013584] CPU 0/0x0 -> Node 0
Jan 25 18:34:14 mahoney kernel: [ 0.013586] CPU: Physical Processor ID: 0
Jan 25 18:34:14 mahoney kernel: [ 0.013587] CPU: Processor Core ID: 0
Jan 25 18:34:14 mahoney kernel: [ 0.013590] mce: CPU supports 6 MCE banks
Jan 25 18:34:14 mahoney kernel: [ 0.013597] CPU0: Thermal monitoring enabled (TM1)
Jan 25 18:34:14 mahoney kernel: [ 0.013602] using mwait in idle threads.
Jan 25 18:34:14 mahoney kernel: [ 0.013603] Performance Events: Core2 events, Intel PMU driver.
Jan 25 18:34:14 mahoney kernel: [ 0.013608] ... version: 2
Jan 25 18:34:14 mahoney kernel: [ 0.013609] ... bit width: 40
Jan 25 18:34:14 mahoney kernel: [ 0.013611] ... generic registers: 2
Jan 25 18:34:14 mahoney kernel: [ 0.013612] ... value mask: 000000ffffffffff
Jan 25 18:34:14 mahoney kernel: [ 0.013613] ... max period: 000000007fffffff
Jan 25 18:34:14 mahoney kernel: [ 0.013615] ... fixed-purpose events: 3
Jan 25 18:34:14 mahoney kernel: [ 0.013616] ... event mask: 0000000700000003
Jan 25 18:34:14 mahoney kernel: [ 0.015505] ACPI: Core revision 20090903
Jan 25 18:34:14 mahoney kernel: [ 0.020288] ftrace: converting mcount calls to 0f 1f 44 00 00
Jan 25 18:34:14 mahoney kernel: [ 0.020292] ftrace: allocating 22785 entries in 90 pages
Jan 25 18:34:14 mahoney kernel: [ 0.027906] Setting APIC routing to flat
Jan 25 18:34:14 mahoney kernel: [ 0.028274] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
Jan 25 18:34:14 mahoney kernel: [ 0.128285] CPU0: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz stepping 06
Jan 25 18:34:14 mahoney kernel: [ 0.130000] Booting processor 1 APIC 0x1 ip 0x6000
Jan 25 18:34:14 mahoney kernel: [ 0.020000] Initializing CPU#1
Jan 25 18:34:14 mahoney kernel: [ 0.020000] CPU: L1 I cache: 32K, L1 D cache: 32K
Jan 25 18:34:14 mahoney kernel: [ 0.020000] CPU: L2 cache: 4096K
Jan 25 18:34:14 mahoney kernel: [ 0.020000] CPU 1/0x1 -> Node 0
Jan 25 18:34:14 mahoney kernel: [ 0.020000] CPU: Physical Processor ID: 0
Jan 25 18:34:14 mahoney kernel: [ 0.020000] CPU: Processor Core ID: 1
Jan 25 18:34:14 mahoney kernel: [ 0.020000] CPU1: Thermal monitoring enabled (TM2)
Jan 25 18:34:14 mahoney kernel: [ 0.280094] CPU1: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz stepping 06
Jan 25 18:34:14 mahoney kernel: [ 0.280100] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Jan 25 18:34:14 mahoney kernel: [ 0.290026] Brought up 2 CPUs
Jan 25 18:34:14 mahoney kernel: [ 0.290028] Total of 2 processors activated (11969.53 BogoMIPS).
Jan 25 18:34:14 mahoney kernel: [ 0.291094] devtmpfs: initialized
Jan 25 18:34:14 mahoney kernel: [ 0.292119] regulator: core version 0.5
Jan 25 18:34:14 mahoney kernel: [ 0.292119] Time: 23:33:49 Date: 01/25/12
Jan 25 18:34:14 mahoney kernel: [ 0.292119] NET: Registered protocol family 16
Jan 25 18:34:14 mahoney kernel: [ 0.292119] ACPI: bus type pci registered
Jan 25 18:34:14 mahoney kernel: [ 0.292119] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
Jan 25 18:34:14 mahoney kernel: [ 0.292119] PCI: MCFG area at e0000000 reserved in E820
Jan 25 18:34:14 mahoney kernel: [ 0.295178] PCI: Using MMCONFIG at e0000000 - efffffff
Jan 25 18:34:14 mahoney kernel: [ 0.295179] PCI: Using configuration type 1 for base access
Jan 25 18:34:14 mahoney kernel: [ 0.295181] PCI: Dell PowerEdge 1950 detected, enabling pci=bfsort.
Jan 25 18:34:14 mahoney kernel: [ 0.295807] Trying to unpack rootfs image as initramfs...
Jan 25 18:34:14 mahoney kernel: [ 0.300123] bio: create slab <bio-0> at 0
Jan 25 18:34:14 mahoney kernel: [ 0.302558] ACPI: Interpreter enabled
Jan 25 18:34:14 mahoney kernel: [ 0.302560] ACPI: (supports S0 S4 S5)
Jan 25 18:34:14 mahoney kernel: [ 0.302571] ACPI: Using IOAPIC for interrupt routing
Jan 25 18:34:14 mahoney kernel: [ 0.305964] ACPI: No dock devices found.
Jan 25 18:34:14 mahoney kernel: [ 0.306097] ACPI: PCI Root Bridge [PCI0] (0000:00)
Jan 25 18:34:14 mahoney kernel: [ 0.306159] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306162] pci 0000:00:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.306204] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306207] pci 0000:00:02.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.306247] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306250] pci 0000:00:03.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.306289] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306291] pci 0000:00:04.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.306329] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306332] pci 0000:00:05.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.306373] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306375] pci 0000:00:06.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.306413] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306416] pci 0000:00:07.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.306627] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306630] pci 0000:00:1c.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.306854] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.306858] pci 0000:00:1d.7: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.308305] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.308397] pci 0000:05:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.309912] pci 0000:05:00.3: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.309958] pci 0000:05:00.3: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.311834] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.311926] pci 0000:06:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.313762] pci 0000:06:01.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.313853] pci 0000:06:01.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.317250] pci 0000:07:00.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.317341] pci 0000:07:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.322569] pci 0000:08:00.0: PME# supported from D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.322660] pci 0000:08:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.328653] pci 0000:01:00.0: PXH quirk detected; SHPC device MSI disabled
Jan 25 18:34:14 mahoney kernel: [ 0.328684] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.328687] pci 0000:01:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.329235] pci 0000:0d:00.0: PME# supported from D0 D3hot
Jan 25 18:34:14 mahoney kernel: [ 0.329239] pci 0000:0d:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.329750] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.329753] pci 0000:03:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.329914] pci 0000:04:00.0: PME# supported from D3hot D3cold
Jan 25 18:34:14 mahoney kernel: [ 0.329918] pci 0000:04:00.0: PME# disabled
Jan 25 18:34:14 mahoney kernel: [ 0.330143] pci 0000:00:1e.0: transparent bridge
Jan 25 18:34:14 mahoney kernel: [ 0.333643] ACPI: PCI Interrupt Link [LK00] (IRQs 3 4 5 *6 7 10 11 12)
Jan 25 18:34:14 mahoney kernel: [ 0.333731] ACPI: PCI Interrupt Link [LK01] (IRQs 3 4 *5 6 7 10 11 12)
Jan 25 18:34:14 mahoney kernel: [ 0.333815] ACPI: PCI Interrupt Link [LK02] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Jan 25 18:34:14 mahoney kernel: [ 0.333899] ACPI: PCI Interrupt Link [LK03] (IRQs 3 4 5 6 7 10 *11 12)
Jan 25 18:34:14 mahoney kernel: [ 0.333982] ACPI: PCI Interrupt Link [LK04] (IRQs 3 4 5 6 7 *10 11 12)
Jan 25 18:34:14 mahoney kernel: [ 0.334069] ACPI: PCI Interrupt Link [LK05] (IRQs 3 4 5 6 7 10 *11 12)
Jan 25 18:34:14 mahoney kernel: [ 0.334151] ACPI: PCI Interrupt Link [LK06] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Jan 25 18:34:14 mahoney kernel: [ 0.334234] ACPI: PCI Interrupt Link [LK07] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
Jan 25 18:34:14 mahoney kernel: [ 0.334340] vgaarb: device added: PCI:0000:10:0d.0,decodes=io+mem,owns=io+mem,locks=none
Jan 25 18:34:14 mahoney kernel: [ 0.334342] vgaarb: loaded
Jan 25 18:34:14 mahoney kernel: [ 0.334428] SCSI subsystem initialized
Jan 25 18:34:14 mahoney kernel: [ 0.334562] usbcore: registered new interface driver usbfs
Jan 25 18:34:14 mahoney kernel: [ 0.334571] usbcore: registered new interface driver hub
Jan 25 18:34:14 mahoney kernel: [ 0.334589] usbcore: registered new device driver usb
Jan 25 18:34:14 mahoney kernel: [ 0.334683] ACPI: WMI: Mapper loaded
Jan 25 18:34:14 mahoney kernel: [ 0.334684] PCI: Using ACPI for IRQ routing
Jan 25 18:34:14 mahoney kernel: [ 0.335319] NetLabel: Initializing
Jan 25 18:34:14 mahoney kernel: [ 0.335321] NetLabel: domain hash size = 128
Jan 25 18:34:14 mahoney kernel: [ 0.335322] NetLabel: protocols = UNLABELED CIPSOv4
Jan 25 18:34:14 mahoney kernel: [ 0.335333] NetLabel: unlabeled traffic allowed by default
Jan 25 18:34:14 mahoney kernel: [ 0.335360] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
Jan 25 18:34:14 mahoney kernel: [ 0.335363] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
Jan 25 18:34:14 mahoney kernel: [ 0.335367] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
Jan 25 18:34:14 mahoney kernel: [ 0.350043] Switching to clocksource tsc
Jan 25 18:34:14 mahoney kernel: [ 0.351475] AppArmor: AppArmor Filesystem Enabled
Jan 25 18:34:14 mahoney kernel: [ 0.351493] pnp: PnP ACPI init
Jan 25 18:34:14 mahoney kernel: [ 0.351511] ACPI: bus type pnp registered
Jan 25 18:34:14 mahoney kernel: [ 0.355073] pnp: PnP ACPI: found 12 devices
Jan 25 18:34:14 mahoney kernel: [ 0.355075] ACPI: ACPI bus type pnp unregistered
Jan 25 18:34:14 mahoney kernel: [ 0.355090] system 00:08: ioport range 0x800-0x87f has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355092] system 00:08: ioport range 0x880-0x8bf has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355094] system 00:08: ioport range 0x8c0-0x8df has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355096] system 00:08: ioport range 0x8e0-0x8e3 has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355098] system 00:08: ioport range 0xc00-0xc7f has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355100] system 00:08: ioport range 0xca0-0xca7 has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355101] system 00:08: ioport range 0xca9-0xcab has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355103] system 00:08: ioport range 0xcad-0xcaf has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355107] system 00:09: ioport range 0xca8-0xca8 has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355109] system 00:09: ioport range 0xcac-0xcac has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.355114] system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
Jan 25 18:34:14 mahoney kernel: [ 0.360790] pci 0000:07:00.0: PCI bridge, secondary bus 0000:08
Jan 25 18:34:14 mahoney kernel: [ 0.360792] pci 0000:07:00.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.360908] pci 0000:07:00.0: MEM window: 0xf4000000-0xf7ffffff
Jan 25 18:34:14 mahoney kernel: [ 0.360999] pci 0000:07:00.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.361183] pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
Jan 25 18:34:14 mahoney kernel: [ 0.361184] pci 0000:06:00.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.361320] pci 0000:06:00.0: MEM window: 0xf4000000-0xf7ffffff
Jan 25 18:34:14 mahoney kernel: [ 0.361367] pci 0000:06:00.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.361504] pci 0000:06:01.0: PCI bridge, secondary bus 0000:09
Jan 25 18:34:14 mahoney kernel: [ 0.361505] pci 0000:06:01.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.361595] pci 0000:06:01.0: MEM window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.361687] pci 0000:06:01.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.361780] pci 0000:05:00.0: PCI bridge, secondary bus 0000:06
Jan 25 18:34:14 mahoney kernel: [ 0.361781] pci 0000:05:00.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.361871] pci 0000:05:00.0: MEM window: 0xf4000000-0xf7ffffff
Jan 25 18:34:14 mahoney kernel: [ 0.361917] pci 0000:05:00.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362055] pci 0000:05:00.3: PCI bridge, secondary bus 0000:0a
Jan 25 18:34:14 mahoney kernel: [ 0.362056] pci 0000:05:00.3: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362146] pci 0000:05:00.3: MEM window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362193] pci 0000:05:00.3: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362330] pci 0000:00:02.0: PCI bridge, secondary bus 0000:05
Jan 25 18:34:14 mahoney kernel: [ 0.362331] pci 0000:00:02.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362334] pci 0000:00:02.0: MEM window: 0xf2000000-0xf7ffffff
Jan 25 18:34:14 mahoney kernel: [ 0.362336] pci 0000:00:02.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362340] pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
Jan 25 18:34:14 mahoney kernel: [ 0.362342] pci 0000:01:00.0: IO window: 0xe000-0xefff
Jan 25 18:34:14 mahoney kernel: [ 0.362346] pci 0000:01:00.0: MEM window: 0xfca00000-0xfcbfffff
Jan 25 18:34:14 mahoney kernel: [ 0.362349] pci 0000:01:00.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362353] pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
Jan 25 18:34:14 mahoney kernel: [ 0.362355] pci 0000:00:03.0: IO window: 0xe000-0xefff
Jan 25 18:34:14 mahoney kernel: [ 0.362358] pci 0000:00:03.0: MEM window: 0xfc900000-0xfcbfffff
Jan 25 18:34:14 mahoney kernel: [ 0.362360] pci 0000:00:03.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362365] pci 0000:00:04.0: PCI bridge, secondary bus 0000:0b
Jan 25 18:34:14 mahoney kernel: [ 0.362367] pci 0000:00:04.0: IO window: 0xd000-0xdfff
Jan 25 18:34:14 mahoney kernel: [ 0.362370] pci 0000:00:04.0: MEM window: 0xfc700000-0xfc8fffff
Jan 25 18:34:14 mahoney kernel: [ 0.362372] pci 0000:00:04.0: PREFETCH window: 0xd0000000-0xd00fffff
Jan 25 18:34:14 mahoney kernel: [ 0.362376] pci 0000:00:05.0: PCI bridge, secondary bus 0000:0c
Jan 25 18:34:14 mahoney kernel: [ 0.362378] pci 0000:00:05.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362380] pci 0000:00:05.0: MEM window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362382] pci 0000:00:05.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362387] pci 0000:0d:00.0: PCI bridge, secondary bus 0000:0e
Jan 25 18:34:14 mahoney kernel: [ 0.362389] pci 0000:0d:00.0: IO window: 0xc000-0xcfff
Jan 25 18:34:14 mahoney kernel: [ 0.362396] pci 0000:0d:00.0: MEM window: 0xfc500000-0xfc6fffff
Jan 25 18:34:14 mahoney kernel: [ 0.362401] pci 0000:0d:00.0: PREFETCH window: 0xd0100000-0xd01fffff
Jan 25 18:34:14 mahoney kernel: [ 0.362409] pci 0000:00:06.0: PCI bridge, secondary bus 0000:0d
Jan 25 18:34:14 mahoney kernel: [ 0.362411] pci 0000:00:06.0: IO window: 0xc000-0xcfff
Jan 25 18:34:14 mahoney kernel: [ 0.362414] pci 0000:00:06.0: MEM window: 0xfc300000-0xfc6fffff
Jan 25 18:34:14 mahoney kernel: [ 0.362417] pci 0000:00:06.0: PREFETCH window: 0xd0100000-0xd01fffff
Jan 25 18:34:14 mahoney kernel: [ 0.362420] pci 0000:00:07.0: PCI bridge, secondary bus 0000:0f
Jan 25 18:34:14 mahoney kernel: [ 0.362422] pci 0000:00:07.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362424] pci 0000:00:07.0: MEM window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362427] pci 0000:00:07.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362430] pci 0000:03:00.0: PCI bridge, secondary bus 0000:04
Jan 25 18:34:14 mahoney kernel: [ 0.362432] pci 0000:03:00.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362436] pci 0000:03:00.0: MEM window: 0xf8000000-0xfbffffff
Jan 25 18:34:14 mahoney kernel: [ 0.362440] pci 0000:03:00.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362446] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03
Jan 25 18:34:14 mahoney kernel: [ 0.362447] pci 0000:00:1c.0: IO window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362451] pci 0000:00:1c.0: MEM window: 0xf8000000-0xfbffffff
Jan 25 18:34:14 mahoney kernel: [ 0.362454] pci 0000:00:1c.0: PREFETCH window: disabled
Jan 25 18:34:14 mahoney kernel: [ 0.362460] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:10
Jan 25 18:34:14 mahoney kernel: [ 0.362463] pci 0000:00:1e.0: IO window: 0xb000-0xbfff
Jan 25 18:34:14 mahoney kernel: [ 0.362467] pci 0000:00:1e.0: MEM window: 0xfc100000-0xfc2fffff
Jan 25 18:34:14 mahoney kernel: [ 0.362471] pci 0000:00:1e.0: PREFETCH window: 0x000000d8000000-0x000000dfffffff
Jan 25 18:34:14 mahoney kernel: [ 0.362493] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.362606] pci 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.362881] pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.363432] pci 0000:06:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.363710] pci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.363725] pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.363738] pci 0000:00:06.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.363749] pci 0000:0d:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.363765] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.363864] NET: Registered protocol family 2
Jan 25 18:34:14 mahoney kernel: [ 0.364014] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
Jan 25 18:34:14 mahoney kernel: [ 0.364961] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
Jan 25 18:34:14 mahoney kernel: [ 0.369133] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
Jan 25 18:34:14 mahoney kernel: [ 0.369659] TCP: Hash tables configured (established 524288 bind 65536)
Jan 25 18:34:14 mahoney kernel: [ 0.369661] TCP reno registered
Jan 25 18:34:14 mahoney kernel: [ 0.369799] NET: Registered protocol family 1
Jan 25 18:34:14 mahoney kernel: [ 0.369913] pci 0000:00:1f.0: rerouting interrupts for [8086:2670]
Jan 25 18:34:14 mahoney kernel: [ 0.369917] pci 0000:01:00.0: rerouting interrupts for [8086:032c]
Jan 25 18:34:14 mahoney kernel: [ 0.370134] Scanning for low memory corruption every 60 seconds
Jan 25 18:34:14 mahoney kernel: [ 0.370234] audit: initializing netlink socket (disabled)
Jan 25 18:34:14 mahoney kernel: [ 0.370248] type=2000 audit(1327534429.369:1): initialized
Jan 25 18:34:14 mahoney kernel: [ 0.377150] HugeTLB registered 2 MB page size, pre-allocated 0 pages
Jan 25 18:34:14 mahoney kernel: [ 0.378189] VFS: Disk quotas dquot_6.5.2
Jan 25 18:34:14 mahoney kernel: [ 0.378229] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Jan 25 18:34:14 mahoney kernel: [ 0.378688] fuse init (API version 7.13)
Jan 25 18:34:14 mahoney kernel: [ 0.378751] msgmni has been set to 7904
Jan 25 18:34:14 mahoney kernel: [ 0.378915] alg: No test for stdrng (krng)
Jan 25 18:34:14 mahoney kernel: [ 0.378956] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
Jan 25 18:34:14 mahoney kernel: [ 0.378959] io scheduler noop registered
Jan 25 18:34:14 mahoney kernel: [ 0.378960] io scheduler anticipatory registered
Jan 25 18:34:14 mahoney kernel: [ 0.378962] io scheduler deadline registered (default)
Jan 25 18:34:14 mahoney kernel: [ 0.379004] io scheduler cfq registered
Jan 25 18:34:14 mahoney kernel: [ 0.387004] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Jan 25 18:34:14 mahoney kernel: [ 0.387026] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
Jan 25 18:34:14 mahoney kernel: [ 0.387110] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
Jan 25 18:34:14 mahoney kernel: [ 0.387113] ACPI: Power Button [PWRF]
Jan 25 18:34:14 mahoney kernel: [ 0.387446] processor LNXCPU:00: registered as cooling_device0
Jan 25 18:34:14 mahoney kernel: [ 0.387638] processor LNXCPU:01: registered as cooling_device1
Jan 25 18:34:14 mahoney kernel: [ 0.390581] Linux agpgart interface v0.103
Jan 25 18:34:14 mahoney kernel: [ 0.390610] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
Jan 25 18:34:14 mahoney kernel: [ 0.390709] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Jan 25 18:34:14 mahoney kernel: [ 0.390801] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Jan 25 18:34:14 mahoney kernel: [ 0.391019] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Jan 25 18:34:14 mahoney kernel: [ 0.391133] 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Jan 25 18:34:14 mahoney kernel: [ 0.391934] brd: module loaded
Jan 25 18:34:14 mahoney kernel: [ 0.392284] loop: module loaded
Jan 25 18:34:14 mahoney kernel: [ 0.392367] input: Macintosh mouse button emulation as /devices/virtual/input/input1
Jan 25 18:34:14 mahoney kernel: [ 0.392477] ata_piix 0000:00:1f.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.392599] scsi0 : ata_piix
Jan 25 18:34:14 mahoney kernel: [ 0.392658] scsi1 : ata_piix
Jan 25 18:34:14 mahoney kernel: [ 0.392681] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
Jan 25 18:34:14 mahoney kernel: [ 0.392683] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
Jan 25 18:34:14 mahoney kernel: [ 0.392932] Fixed MDIO Bus: probed
Jan 25 18:34:14 mahoney kernel: [ 0.392957] PPP generic driver version 2.4.2
Jan 25 18:34:14 mahoney kernel: [ 0.392980] tun: Universal TUN/TAP device driver, 1.6
Jan 25 18:34:14 mahoney kernel: [ 0.392982] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Jan 25 18:34:14 mahoney kernel: [ 0.393053] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 25 18:34:14 mahoney kernel: [ 0.393074] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 21 (level, low) -> IRQ 21
Jan 25 18:34:14 mahoney kernel: [ 0.393094] ehci_hcd 0000:00:1d.7: EHCI Host Controller
Jan 25 18:34:14 mahoney kernel: [ 0.393124] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
Jan 25 18:34:14 mahoney kernel: [ 0.393160] ehci_hcd 0000:00:1d.7: debug port 1
Jan 25 18:34:14 mahoney kernel: [ 0.397063] ehci_hcd 0000:00:1d.7: irq 21, io mem 0xfcc00000
Jan 25 18:34:14 mahoney kernel: [ 0.419900] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
Jan 25 18:34:14 mahoney kernel: [ 0.420009] usb usb1: configuration #1 chosen from 1 choice
Jan 25 18:34:14 mahoney kernel: [ 0.420032] hub 1-0:1.0: USB hub found
Jan 25 18:34:14 mahoney kernel: [ 0.420040] hub 1-0:1.0: 6 ports detected
Jan 25 18:34:14 mahoney kernel: [ 0.420102] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
Jan 25 18:34:14 mahoney kernel: [ 0.420120] uhci_hcd: USB Universal Host Controller Interface driver
Jan 25 18:34:14 mahoney kernel: [ 0.420159] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
Jan 25 18:34:14 mahoney kernel: [ 0.420169] uhci_hcd 0000:00:1d.0: UHCI Host Controller
Jan 25 18:34:14 mahoney kernel: [ 0.420198] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
Jan 25 18:34:14 mahoney kernel: [ 0.420222] uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ace0
Jan 25 18:34:14 mahoney kernel: [ 0.420284] usb usb2: configuration #1 chosen from 1 choice
Jan 25 18:34:14 mahoney kernel: [ 0.420302] hub 2-0:1.0: USB hub found
Jan 25 18:34:14 mahoney kernel: [ 0.420307] hub 2-0:1.0: 2 ports detected
Jan 25 18:34:14 mahoney kernel: [ 0.420350] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20
Jan 25 18:34:14 mahoney kernel: [ 0.420357] uhci_hcd 0000:00:1d.1: UHCI Host Controller
Jan 25 18:34:14 mahoney kernel: [ 0.420381] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
Jan 25 18:34:14 mahoney kernel: [ 0.420410] uhci_hcd 0000:00:1d.1: irq 20, io base 0x0000acc0
Jan 25 18:34:14 mahoney kernel: [ 0.420476] usb usb3: configuration #1 chosen from 1 choice
Jan 25 18:34:14 mahoney kernel: [ 0.420494] hub 3-0:1.0: USB hub found
Jan 25 18:34:14 mahoney kernel: [ 0.420501] hub 3-0:1.0: 2 ports detected
Jan 25 18:34:14 mahoney kernel: [ 0.420534] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 21 (level, low) -> IRQ 21
Jan 25 18:34:14 mahoney kernel: [ 0.420540] uhci_hcd 0000:00:1d.2: UHCI Host Controller
Jan 25 18:34:14 mahoney kernel: [ 0.420562] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
Jan 25 18:34:14 mahoney kernel: [ 0.420581] uhci_hcd 0000:00:1d.2: irq 21, io base 0x0000aca0
Jan 25 18:34:14 mahoney kernel: [ 0.420645] usb usb4: configuration #1 chosen from 1 choice
Jan 25 18:34:14 mahoney kernel: [ 0.420662] hub 4-0:1.0: USB hub found
Jan 25 18:34:14 mahoney kernel: [ 0.420666] hub 4-0:1.0: 2 ports detected
Jan 25 18:34:14 mahoney kernel: [ 0.420736] PNP: No PS/2 controller found. Probing ports directly.
Jan 25 18:34:14 mahoney kernel: [ 0.423414] serio: i8042 KBD port at 0x60,0x64 irq 1
Jan 25 18:34:14 mahoney kernel: [ 0.423419] serio: i8042 AUX port at 0x60,0x64 irq 12
Jan 25 18:34:14 mahoney kernel: [ 0.423483] mice: PS/2 mouse device common for all mice
Jan 25 18:34:14 mahoney kernel: [ 0.423547] rtc_cmos 00:04: RTC can wake from S4
Jan 25 18:34:14 mahoney kernel: [ 0.423579] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
Jan 25 18:34:14 mahoney kernel: [ 0.423601] rtc0: alarms up to one day, y3k, 242 bytes nvram, hpet irqs
Jan 25 18:34:14 mahoney kernel: [ 0.423700] device-mapper: uevent: version 1.0.3
Jan 25 18:34:14 mahoney kernel: [ 0.423809] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
Jan 25 18:34:14 mahoney kernel: [ 0.423860] device-mapper: multipath: version 1.1.0 loaded
Jan 25 18:34:14 mahoney kernel: [ 0.423862] device-mapper: multipath round-robin: version 1.0.0 loaded
Jan 25 18:34:14 mahoney kernel: [ 0.423971] cpuidle: using governor ladder
Jan 25 18:34:14 mahoney kernel: [ 0.423972] cpuidle: using governor menu
Jan 25 18:34:14 mahoney kernel: [ 0.424235] TCP cubic registered
Jan 25 18:34:14 mahoney kernel: [ 0.424344] NET: Registered protocol family 10
Jan 25 18:34:14 mahoney kernel: [ 0.424900] NET: Registered protocol family 17
Jan 25 18:34:14 mahoney kernel: [ 0.425015] registered taskstats version 1
Jan 25 18:34:14 mahoney kernel: [ 0.428759] Magic number: 12:318:606
Jan 25 18:34:14 mahoney kernel: [ 0.428842] rtc_cmos 00:04: setting system clock to 2012-01-25 23:33:49 UTC (1327534429)
Jan 25 18:34:14 mahoney kernel: [ 0.428844] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
Jan 25 18:34:14 mahoney kernel: [ 0.428845] EDD information not available.
Jan 25 18:34:14 mahoney kernel: [ 0.447311] Freeing initrd memory: 8898k freed
Jan 25 18:34:14 mahoney kernel: [ 0.580560] ata1.00: ATAPI: TSSTcorpCD-RW/DVD-ROM TSL462D, DE04, max UDMA/33
Jan 25 18:34:14 mahoney kernel: [ 0.640567] ata1.00: configured for UDMA/33
Jan 25 18:34:14 mahoney kernel: [ 0.672559] scsi 0:0:0:0: CD-ROM TSSTcorp CDRW/DVD TSL462D DE04 PQ: 0 ANSI: 5
Jan 25 18:34:14 mahoney kernel: [ 0.740620] usb 1-5: new high speed USB device using ehci_hcd and address 2
Jan 25 18:34:14 mahoney kernel: [ 0.759753] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Jan 25 18:34:14 mahoney kernel: [ 0.759757] Uniform CD-ROM driver Revision: 3.20
Jan 25 18:34:14 mahoney kernel: [ 0.759942] sr 0:0:0:0: Attached scsi generic sg0 type 5
Jan 25 18:34:14 mahoney kernel: [ 0.760018] Freeing unused kernel memory: 812k freed
Jan 25 18:34:14 mahoney kernel: [ 0.760261] Write protecting the kernel read-only data: 7812k
Jan 25 18:34:14 mahoney kernel: [ 0.770769] udev: starting version 151
Jan 25 18:34:14 mahoney kernel: [ 0.824286] Fusion MPT base driver 3.04.12
Jan 25 18:34:14 mahoney kernel: [ 0.824288] Copyright (c) 1999-2008 LSI Corporation
Jan 25 18:34:14 mahoney kernel: [ 0.831745] Fusion MPT SPI Host driver 3.04.12
Jan 25 18:34:14 mahoney kernel: [ 0.831789] mptspi 0000:0e:08.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.835442] mptbase: ioc0: Initiating bringup
Jan 25 18:34:14 mahoney kernel: [ 0.838241] QLogic Fibre Channel HBA Driver: 8.03.01-k6
Jan 25 18:34:14 mahoney kernel: [ 0.838276] qla2xxx 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 0.838318] qla2xxx 0000:0b:00.0: Found an ISP2432, irq 16, iobase 0xffffc90000656000
Jan 25 18:34:14 mahoney kernel: [ 0.841815] Fusion MPT SAS Host driver 3.04.12
Jan 25 18:34:14 mahoney kernel: [ 0.841855] mptsas 0000:02:08.0: PCI INT A -> GSI 64 (level, low) -> IRQ 64
Jan 25 18:34:14 mahoney kernel: [ 0.847542] qla2xxx 0000:0b:00.0: Configuring PCI space...
Jan 25 18:34:14 mahoney kernel: [ 0.850928] mptbase: ioc1: Initiating bringup
Jan 25 18:34:14 mahoney kernel: [ 0.878503] qla2xxx 0000:0b:00.0: Configure NVRAM parameters...
Jan 25 18:34:14 mahoney kernel: [ 0.891100] usb 1-5: configuration #1 chosen from 1 choice
Jan 25 18:34:14 mahoney kernel: [ 0.891288] hub 1-5:1.0: USB hub found
Jan 25 18:34:14 mahoney kernel: [ 0.891418] hub 1-5:1.0: 4 ports detected
Jan 25 18:34:14 mahoney kernel: [ 0.914165] qla2xxx 0000:0b:00.0: Verifying loaded RISC code...
Jan 25 18:34:14 mahoney kernel: [ 0.930909] qla2xxx 0000:0b:00.0: firmware: requesting ql2400_fw.bin
Jan 25 18:34:14 mahoney kernel: [ 0.932097] qla2xxx 0000:0b:00.0: FW: Loading via request-firmware...
Jan 25 18:34:14 mahoney kernel: [ 1.170106] qla2xxx 0000:0b:00.0: Allocated (64 KB) for EFT...
Jan 25 18:34:14 mahoney kernel: [ 1.170184] qla2xxx 0000:0b:00.0: Allocated (1285 KB) for firmware dump...
Jan 25 18:34:14 mahoney kernel: [ 1.170812] usb 1-5.1: new low speed USB device using ehci_hcd and address 3
Jan 25 18:34:14 mahoney kernel: [ 1.200126] scsi2 : qla2xxx
Jan 25 18:34:14 mahoney kernel: [ 1.200380] qla2xxx 0000:0b:00.0:
Jan 25 18:34:14 mahoney kernel: [ 1.200381] QLogic Fibre Channel HBA Driver: 8.03.01-k6
Jan 25 18:34:14 mahoney kernel: [ 1.200382] QLogic QLE2462 - PCI-Express Dual Channel 4Gb Fibre Channel HBA
Jan 25 18:34:14 mahoney kernel: [ 1.200382] ISP2432: PCIe (2.5GT/s x4) @ 0000:0b:00.0 hdma+, host#=2, fw=4.04.04 (482)
Jan 25 18:34:14 mahoney kernel: [ 1.200411] qla2xxx 0000:0b:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Jan 25 18:34:14 mahoney kernel: [ 1.200448] qla2xxx 0000:0b:00.1: Found an ISP2432, irq 17, iobase 0xffffc90000622000
Jan 25 18:34:14 mahoney kernel: [ 1.200615] qla2xxx 0000:0b:00.1: Configuring PCI space...
Jan 25 18:34:14 mahoney kernel: [ 1.231195] qla2xxx 0000:0b:00.1: Configure NVRAM parameters...
Jan 25 18:34:14 mahoney kernel: [ 1.266892] qla2xxx 0000:0b:00.1: Verifying loaded RISC code...
Jan 25 18:34:14 mahoney kernel: [ 1.280074] qla2xxx 0000:0b:00.1: FW: Loading via request-firmware...
Jan 25 18:34:14 mahoney kernel: [ 1.293767] usb 1-5.1: configuration #1 chosen from 1 choice
Jan 25 18:34:14 mahoney kernel: [ 1.301119] usbcore: registered new interface driver hiddev
Jan 25 18:34:14 mahoney kernel: [ 1.303216] input: PIXART USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input2
Jan 25 18:34:14 mahoney kernel: [ 1.303285] generic-usb 0003:093A:2510.0001: input,hidraw0: USB HID v1.11 Mouse [PIXART USB OPTICAL MOUSE] on usb-0000:00:1d.7-5.1/input0
Jan 25 18:34:14 mahoney kernel: [ 1.303301] usbcore: registered new interface driver usbhid
Jan 25 18:34:14 mahoney kernel: [ 1.303302] usbhid: v2.6:USB HID core driver
Jan 25 18:34:14 mahoney kernel: [ 1.380207] usb 1-5.2: new low speed USB device using ehci_hcd and address 4
Jan 25 18:34:14 mahoney kernel: [ 1.504896] usb 1-5.2: configuration #1 chosen from 1 choice
Jan 25 18:34:14 mahoney kernel: [ 1.507746] input: DELL DELL USB Keyboard as /devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input3
Jan 25 18:34:14 mahoney kernel: [ 1.507807] generic-usb 0003:413C:2005.0002: input,hidraw1: USB HID v1.10 Keyboard [DELL DELL USB Keyboard] on usb-0000:00:1d.7-5.2/input0
Jan 25 18:34:14 mahoney kernel: [ 1.520710] qla2xxx 0000:0b:00.1: Allocated (64 KB) for EFT...
Jan 25 18:34:14 mahoney kernel: [ 1.520783] qla2xxx 0000:0b:00.1: Allocated (1285 KB) for firmware dump...
Jan 25 18:34:14 mahoney kernel: [ 1.540785] scsi3 : qla2xxx
Jan 25 18:34:14 mahoney kernel: [ 1.541009] qla2xxx 0000:0b:00.1:
Jan 25 18:34:14 mahoney kernel: [ 1.541010] QLogic Fibre Channel HBA Driver: 8.03.01-k6
Jan 25 18:34:14 mahoney kernel: [ 1.541010] QLogic QLE2462 - PCI-Express Dual Channel 4Gb Fibre Channel HBA
Jan 25 18:34:14 mahoney kernel: [ 1.541011] ISP2432: PCIe (2.5GT/s x4) @ 0000:0b:00.1 hdma+, host#=3, fw=4.04.04 (482)
Jan 25 18:34:14 mahoney kernel: [ 1.732561] qla2xxx 0000:0b:00.0: LIP reset occurred (f802).
Jan 25 18:34:14 mahoney kernel: [ 1.787027] qla2xxx 0000:0b:00.0: LIP occurred (f802).
Jan 25 18:34:14 mahoney kernel: [ 1.791118] qla2xxx 0000:0b:00.0: LOOP UP detected (4 Gbps).
Jan 25 18:34:14 mahoney kernel: [ 1.989438] qla2xxx 0000:0b:00.1: LIP reset occurred (f802).
Jan 25 18:34:14 mahoney kernel: [ 2.070035] ioc0: LSI53C1030 C0: Capabilities={Initiator,Target}
Jan 25 18:34:14 mahoney kernel: [ 2.112401] qla2xxx 0000:0b:00.1: LIP occurred (f802).
Jan 25 18:34:14 mahoney kernel: [ 2.116495] qla2xxx 0000:0b:00.1: LOOP UP detected (4 Gbps).
Jan 25 18:34:14 mahoney kernel: [ 2.293900] scsi 2:0:0:0: Sequential-Access HP Ultrium 5-SCSI Y23U PQ: 0 ANSI: 6
Jan 25 18:34:14 mahoney kernel: [ 2.310182] scsi 2:0:0:0: Attached scsi generic sg1 type 1
Jan 25 18:34:14 mahoney kernel: [ 2.313459] st: Version 20081215, fixed bufsize 32768, s/g segs 256
Jan 25 18:34:14 mahoney kernel: [ 2.313632] st 2:0:0:0: Attached scsi tape st0
Jan 25 18:34:14 mahoney kernel: [ 2.313634] st 2:0:0:0: st0: try direct i/o: yes (alignment 4 B)
Jan 25 18:34:14 mahoney kernel: [ 2.315230] osst :I: Tape driver with OnStream support version 0.99.4
Jan 25 18:34:14 mahoney kernel: [ 2.315231] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
Jan 25 18:34:14 mahoney kernel: [ 2.410049] ioc1: LSISAS1068 B0: Capabilities={Initiator}
Jan 25 18:34:14 mahoney kernel: [ 2.623135] scsi 3:0:0:0: Sequential-Access HP Ultrium 5-SCSI Y23U PQ: 0 ANSI: 6
Jan 25 18:34:14 mahoney kernel: [ 2.627064] scsi 3:0:0:1: Medium Changer TANDBERG StorageLoader 0416 PQ: 0 ANSI: 3
Jan 25 18:34:14 mahoney kernel: [ 2.640347] st 3:0:0:0: Attached scsi tape st1
Jan 25 18:34:14 mahoney kernel: [ 2.640349] st 3:0:0:0: st1: try direct i/o: yes (alignment 4 B)
Jan 25 18:34:14 mahoney kernel: [ 2.640384] st 3:0:0:0: Attached scsi generic sg2 type 1
Jan 25 18:34:14 mahoney kernel: [ 2.640463] scsi 3:0:0:1: Attached scsi generic sg3 type 8
Jan 25 18:34:14 mahoney kernel: [ 2.642756] SCSI Media Changer driver v0.25
Jan 25 18:34:14 mahoney kernel: [ 2.643686] ch0: type #1 (mt): 0x1+1 [medium transport]
Jan 25 18:34:14 mahoney kernel: [ 2.643689] ch0: type #2 (st): 0x1000+12 [storage]
Jan 25 18:34:14 mahoney kernel: [ 2.643691] ch0: type #3 (ie): 0x0+0 [import/export]
Jan 25 18:34:14 mahoney kernel: [ 2.643693] ch0: type #4 (dt): 0x100+2 [data transfer]
Jan 25 18:34:14 mahoney kernel: [ 2.777925] ch0: dt 0x100: ID/LUN unknown
Jan 25 18:34:14 mahoney kernel: [ 2.920079] ch0: dt 0x101: ID/LUN unknown
Jan 25 18:34:14 mahoney kernel: [ 2.920081] ch0: INITIALIZE ELEMENT STATUS, may take some time ...
Jan 25 18:34:14 mahoney kernel: [ 2.990496] ch0: ... finished
Jan 25 18:34:14 mahoney kernel: [ 2.990498] ch 3:0:0:1: Attached scsi changer ch0
Jan 25 18:34:14 mahoney kernel: [ 3.278502] scsi4 : ioc0: LSI53C1030 C0, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=16
Jan 25 18:34:14 mahoney kernel: [ 3.860040] floppy0: no floppy controllers found
Jan 25 18:34:14 mahoney kernel: [ 4.075328] mptspi 0000:0e:08.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Jan 25 18:34:14 mahoney kernel: [ 4.075428] mptbase: ioc2: Initiating bringup
Jan 25 18:34:14 mahoney kernel: [ 4.512064] scsi5 : ioc1: LSISAS1068 B0, FwRev=000a3100h, Ports=1, MaxQ=366, IRQ=64
Jan 25 18:34:14 mahoney kernel: [ 4.553136] mptsas: ioc1: attaching sata device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x1221000000000000
Jan 25 18:34:14 mahoney kernel: [ 4.553223] scsi: waiting for bus probes to complete ...
Jan 25 18:34:14 mahoney kernel: [ 5.290048] ioc2: LSI53C1030 C0: Capabilities={Initiator,Target}
Jan 25 18:34:14 mahoney kernel: [ 6.488494] scsi6 : ioc2: LSI53C1030 C0, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=17
Jan 25 18:34:14 mahoney kernel: [ 6.720186] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 7.297856] scsi 6:0:0:0: Direct-Access CRU RTX-UR 239 PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.297867] scsi target6:0:0: Beginning Domain Validation
Jan 25 18:34:14 mahoney kernel: [ 7.304353] scsi target6:0:0: Ending Domain Validation
Jan 25 18:34:14 mahoney kernel: [ 7.304417] scsi target6:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP (6.25 ns, offset 127)
Jan 25 18:34:14 mahoney kernel: [ 7.304990] scsi 6:0:0:1: Direct-Access CRU RTX-UR 239 PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.305341] scsi 6:0:0:2: Direct-Access CRU RTX-UR 239 PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.305691] scsi 6:0:0:3: Direct-Access CRU RTX-UR 239 PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.306040] scsi 6:0:0:4: Direct-Access CRU RTX-UR 239 PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.306226] scsi 6:0:0:7: Processor CRU RTX-UR 239 PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.556408] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 7.570766] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 7.571721] scsi 4:0:2:0: Direct-Access WiebeTec ProSATA 2.3. PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.571729] scsi target4:0:2: Beginning Domain Validation
Jan 25 18:34:14 mahoney kernel: [ 7.578087] scsi target4:0:2: Ending Domain Validation
Jan 25 18:34:14 mahoney kernel: [ 7.578152] scsi target4:0:2: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP (6.25 ns, offset 127)
Jan 25 18:34:14 mahoney kernel: [ 7.806591] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 7.807581] scsi 6:0:3:0: Direct-Access CRU RTX-UR 239 PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.807589] scsi target6:0:3: Beginning Domain Validation
Jan 25 18:34:14 mahoney kernel: [ 7.814137] scsi target6:0:3: Ending Domain Validation
Jan 25 18:34:14 mahoney kernel: [ 7.814203] scsi target6:0:3: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP (6.25 ns, offset 127)
Jan 25 18:34:14 mahoney kernel: [ 7.814605] scsi 6:0:3:7: Processor CRU RTX-UR 239 PQ: 0 ANSI: 4
Jan 25 18:34:14 mahoney kernel: [ 7.828542] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 8.064790] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 8.078721] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 8.314967] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 8.328895] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 8.565142] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 8.579070] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 8.815318] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 8.829245] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 9.065492] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 9.079420] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 9.315668] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 9.329594] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 9.565842] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 9.579770] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 9.816017] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 9.829944] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 10.066191] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 10.080119] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 10.316366] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 10.330293] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 10.566540] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 10.580468] scsi: killing requests for dead queue
Jan 25 18:34:14 mahoney kernel: [ 10.580680] sd 4:0:2:0: Attached scsi generic sg4 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.580862] sd 6:0:0:0: Attached scsi generic sg5 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.580949] sd 6:0:0:1: Attached scsi generic sg6 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.581038] sd 6:0:0:2: Attached scsi generic sg7 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.581126] sd 6:0:0:3: Attached scsi generic sg8 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.581221] sd 6:0:0:4: Attached scsi generic sg9 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.581312] scsi 6:0:0:7: Attached scsi generic sg10 type 3
Jan 25 18:34:14 mahoney kernel: [ 10.581424] sd 6:0:3:0: Attached scsi generic sg11 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.581505] scsi 6:0:3:7: Attached scsi generic sg12 type 3
Jan 25 18:34:14 mahoney kernel: [ 10.583637] sd 4:0:2:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.583793] sd 4:0:2:0: [sda] 23438032896 512-byte logical blocks: (12.0 TB/10.9 TiB)
Jan 25 18:34:14 mahoney kernel: [ 10.583866] scsi 5:0:0:0: Direct-Access ATA WDC WD800AAJS-18 0A04 PQ: 0 ANSI: 5
Jan 25 18:34:14 mahoney kernel: [ 10.583953] sd 4:0:2:0: [sda] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.584159] sd 6:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.584241] sd 4:0:2:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.584290] sd 6:0:0:1: [sdc] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.584410] sd 6:0:3:0: [sdg] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.584439] sd 6:0:0:2: [sdd] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.584476] sd 6:0:0:3: [sde] 524550144 512-byte logical blocks: (268 GB/250 GiB)
Jan 25 18:34:14 mahoney kernel: [ 10.584572] sd 4:0:2:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.584596] sd 6:0:0:4: [sdf] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.584620] sd 6:0:3:0: [sdg] 23438032896 512-byte logical blocks: (12.0 TB/10.9 TiB)
Jan 25 18:34:14 mahoney kernel: [ 10.584648] sd 6:0:0:0: [sdb] 8590196736 512-byte logical blocks: (4.39 TB/4.00 TiB)
Jan 25 18:34:14 mahoney kernel: [ 10.584682] sd 6:0:0:1: [sdc] 4295098368 512-byte logical blocks: (2.19 TB/2.00 TiB)
Jan 25 18:34:14 mahoney kernel: [ 10.584934] sd 6:0:0:3: [sde] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.584945] sd 6:0:0:2: [sdd] 4295098368 512-byte logical blocks: (2.19 TB/2.00 TiB)
Jan 25 18:34:14 mahoney kernel: [ 10.584958] sd 6:0:0:0: [sdb] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.584971] sd 6:0:0:4: [sdf] 5733875712 512-byte logical blocks: (2.93 TB/2.66 TiB)
Jan 25 18:34:14 mahoney kernel: [ 10.584977] sd 6:0:3:0: [sdg] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.584988] sd 6:0:0:1: [sdc] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.585250] sda:
Jan 25 18:34:14 mahoney kernel: [ 10.585294] sd 6:0:0:2: [sdd] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.585375] sd 6:0:0:4: [sdf] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.585573] sd 6:0:3:0: [sdg] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.585633] sd 6:0:0:3: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.585729] sd 6:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.585954] sd 6:0:0:1: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.585983] sd 5:0:0:0: Attached scsi generic sg13 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.586059] sd 6:0:0:2: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.586101] sd 6:0:3:0: [sdg] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.586183] sd 6:0:0:4: [sdf] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.586503] sd 6:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.586684] sd 6:0:0:1: [sdc] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.586840] sd 6:0:0:2: [sdd] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.587029] sd 6:0:0:4: [sdf] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.587100] sdg:
Jan 25 18:34:14 mahoney kernel: [ 10.587659] sde:
Jan 25 18:34:14 mahoney kernel: [ 10.587737] mptsas: ioc1: attaching sata device: fw_channel 0, fw_id 1, phy 1, sas_addr 0x1221000001000000
Jan 25 18:34:14 mahoney kernel: [ 10.588122] sdb:
Jan 25 18:34:14 mahoney kernel: [ 10.588313] sdc:
Jan 25 18:34:14 mahoney kernel: [ 10.588572] sdd:
Jan 25 18:34:14 mahoney kernel: [ 10.588588] sd 5:0:0:0: [sdh] 156250000 512-byte logical blocks: (80.0 GB/74.5 GiB)
Jan 25 18:34:14 mahoney kernel: [ 10.588713] sdf:
Jan 25 18:34:14 mahoney kernel: [ 10.590875] scsi 5:0:1:0: Direct-Access ATA WDC WD800AAJS-18 0A04 PQ: 0 ANSI: 5
Jan 25 18:34:14 mahoney kernel: [ 10.593293] sd 5:0:1:0: Attached scsi generic sg14 type 0
Jan 25 18:34:14 mahoney kernel: [ 10.594984] sd 5:0:1:0: [sdi] 156250000 512-byte logical blocks: (80.0 GB/74.5 GiB)
Jan 25 18:34:14 mahoney kernel: [ 10.597630] sd 5:0:0:0: [sdh] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.599751] sd 5:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.603304] sd 5:0:1:0: [sdi] Write Protect is off
Jan 25 18:34:14 mahoney kernel: [ 10.605237] sd 5:0:1:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jan 25 18:34:14 mahoney kernel: [ 10.609796] sdh:
Jan 25 18:34:14 mahoney kernel: [ 10.614982] sdi: sdh1 sdh2 sdh3 sdh4
Jan 25 18:34:14 mahoney kernel: [ 10.627958]
Jan 25 18:34:14 mahoney kernel: [ 10.638664] sd 5:0:0:0: [sdh] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 10.639101] sd 5:0:1:0: [sdi] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 10.646106] sde1
Jan 25 18:34:14 mahoney kernel: [ 10.646417] sdb1
Jan 25 18:34:14 mahoney kernel: [ 10.646560] sdc1
Jan 25 18:34:14 mahoney kernel: [ 10.646720] sdd1
Jan 25 18:34:14 mahoney kernel: [ 10.646850] sdf1
Jan 25 18:34:14 mahoney kernel: [ 10.647376] sd 6:0:0:1: [sdc] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.647458] sd 6:0:0:2: [sdd] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.647493] sd 6:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.647962] sd 6:0:0:4: [sdf] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.649472] sd 6:0:0:1: [sdc] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 10.649583] sd 6:0:0:2: [sdd] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 10.649617] sd 6:0:0:0: [sdb] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 10.649692] sd 6:0:0:3: [sde] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 10.650374] sd 6:0:0:4: [sdf] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 10.695758] sda1
Jan 25 18:34:14 mahoney kernel: [ 10.696241] sd 4:0:2:0: [sda] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.696830] sd 4:0:2:0: [sda] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 10.737122] sdg1
Jan 25 18:34:14 mahoney kernel: [ 10.737596] sd 6:0:3:0: [sdg] Very big device. Trying to use READ CAPACITY(16).
Jan 25 18:34:14 mahoney kernel: [ 10.738290] sd 6:0:3:0: [sdg] Attached SCSI disk
Jan 25 18:34:14 mahoney kernel: [ 11.409641] kjournald starting. Commit interval 5 seconds
Jan 25 18:34:14 mahoney kernel: [ 11.409662] EXT3-fs: mounted filesystem with ordered data mode.
Jan 25 18:34:14 mahoney kernel: [ 22.639039] udev: starting version 151
Jan 25 18:34:14 mahoney kernel: [ 22.646885] Adding 7812088k swap on /dev/sdh3. Priority:-1 extents:1 across:7812088k
Jan 25 18:34:14 mahoney kernel: [ 22.832907] type=1505 audit(1327534451.901:2): operation="profile_load" pid=620 name="/sbin/dhclient3"
Jan 25 18:34:14 mahoney kernel: [ 22.833387] type=1505 audit(1327534451.901:3): operation="profile_load" pid=620 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
Jan 25 18:34:14 mahoney kernel: [ 22.833659] type=1505 audit(1327534451.901:4): operation="profile_load" pid=620 name="/usr/lib/connman/scripts/dhclient-script"
Jan 25 18:34:14 mahoney kernel: [ 22.835321] type=1505 audit(1327534451.901:5): operation="profile_load" pid=685 name="/usr/sbin/ntpd"
Jan 25 18:34:14 mahoney kernel: [ 22.977246] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
Jan 25 18:34:14 mahoney kernel: [ 23.043772] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Jan 25 18:34:14 mahoney kernel: [ 23.239933] intel_rng: FWH not detected
Jan 25 18:34:14 mahoney kernel: [ 23.341735] ipmi message handler version 39.2
Jan 25 18:34:14 mahoney kernel: [ 23.373098] dell-wmi: No known WMI GUID found
Jan 25 18:34:14 mahoney kernel: [ 23.383662] ipmi device interface
Jan 25 18:34:14 mahoney kernel: [ 23.575968] EDAC MC: Ver: 2.1.0 Dec 2 2011
Jan 25 18:34:14 mahoney kernel: [ 23.579521] IPMI System Interface driver.
Jan 25 18:34:14 mahoney kernel: [ 23.579524] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca8, slave address 0x20, irq 0
Jan 25 18:34:14 mahoney kernel: [ 23.743018] EDAC MC0: Giving out device to 'i5000_edac.c' 'I5000': DEV 0000:00:10.0
Jan 25 18:34:14 mahoney kernel: [ 23.743036] EDAC PCI0: Giving out device to module 'i5000_edac' controller 'EDAC PCI controller': DEV '0000:00:10.0' (POLLED)
Jan 25 18:34:14 mahoney kernel: [ 23.845162] Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.0.2 (Aug 21, 2009)
Jan 25 18:34:14 mahoney kernel: [ 23.845179] bnx2 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 23.909022] ipmi: Found new BMC (man_id: 0x0002a2, prod_id: 0x0100, dev_id: 0x20)
Jan 25 18:34:14 mahoney kernel: [ 23.909071] IPMI kcs interface initialized
Jan 25 18:34:14 mahoney kernel: [ 23.960291] [drm] Initialized drm 1.1.0 20060810
Jan 25 18:34:14 mahoney kernel: [ 24.324314] [drm] radeon disabling kernel modesetting for known bad device.
Jan 25 18:34:14 mahoney kernel: [ 24.324547] pci 0000:10:0d.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
Jan 25 18:34:14 mahoney kernel: [ 24.324710] [drm] Initialized radeon 1.32.0 20080528 for 0000:10:0d.0 on minor 0
Jan 25 18:34:14 mahoney kernel: [ 24.440826] bnx2 0000:04:00.0: firmware: requesting bnx2/bnx2-mips-06-5.0.0.j3.fw
Jan 25 18:34:14 mahoney kernel: [ 24.449616] EXT3 FS on sdh4, internal journal
Jan 25 18:34:14 mahoney kernel: [ 24.648437] bnx2 0000:04:00.0: firmware: requesting bnx2/bnx2-rv2p-06-5.0.0.j3.fw
Jan 25 18:34:14 mahoney kernel: [ 24.660618] vga16fb: mapped to 0xffff8800000a0000
Jan 25 18:34:14 mahoney kernel: [ 24.660676] fb0: VGA16 VGA frame buffer device
Jan 25 18:34:14 mahoney kernel: [ 24.760787] eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 16, node addr 00:19:b9:e4:a3:68
Jan 25 18:34:14 mahoney kernel: [ 24.760951] bnx2 0000:08:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jan 25 18:34:14 mahoney kernel: [ 24.891764] bnx2: eth0: using MSI
Jan 25 18:34:14 mahoney kernel: [ 24.892132] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jan 25 18:34:14 mahoney kernel: [ 25.360651] bnx2 0000:08:00.0: firmware: requesting bnx2/bnx2-mips-06-5.0.0.j3.fw
Jan 25 18:34:14 mahoney kernel: [ 25.362034] bnx2 0000:08:00.0: firmware: requesting bnx2/bnx2-rv2p-06-5.0.0.j3.fw
Jan 25 18:34:14 mahoney kernel: [ 25.363863] eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 16, node addr 00:19:b9:e4:a3:6a
Jan 25 18:34:14 mahoney kernel: [ 25.414424] Console: switching to colour frame buffer device 80x30
Jan 25 18:34:14 mahoney kernel: [ 25.482773] type=1505 audit(1327534454.551:6): operation="profile_replace" pid=1045 name="/sbin/dhclient3"
Jan 25 18:34:14 mahoney kernel: [ 25.483265] type=1505 audit(1327534454.551:7): operation="profile_replace" pid=1045 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
Jan 25 18:34:14 mahoney kernel: [ 25.483532] type=1505 audit(1327534454.551:8): operation="profile_replace" pid=1045 name="/usr/lib/connman/scripts/dhclient-script"
Jan 25 18:34:14 mahoney kernel: [ 25.485644] type=1505 audit(1327534454.551:9): operation="profile_load" pid=1047 name="/usr/lib/cups/backend/cups-pdf"
Jan 25 18:34:14 mahoney kernel: [ 25.486245] type=1505 audit(1327534454.551:10): operation="profile_load" pid=1047 name="/usr/sbin/cupsd"
Jan 25 18:34:14 mahoney kernel: [ 25.486537] type=1505 audit(1327534454.551:11): operation="profile_load" pid=1046 name="/usr/bin/evince"
Jan 25 18:34:14 mahoney kernel: [ 25.571772] bnx2: eth1: using MSI
Jan 25 18:34:14 mahoney kernel: [ 25.572131] ADDRCONF(NETDEV_UP): eth1: link is not ready
Jan 25 18:34:15 mahoney kernel: [ 26.040714] floppy0: no floppy controllers found
Jan 25 18:34:15 mahoney kernel: [ 26.549579] bnx2: eth0 NIC Copper Link is Up, 100 Mbps full duplex
Jan 25 18:34:15 mahoney kernel: [ 26.549964] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jan 25 18:34:16 mahoney kernel: [ 27.187676] bnx2: eth1 NIC Copper Link is Up, 100 Mbps full duplex
Jan 25 18:34:16 mahoney kernel: [ 27.188063] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
Jan 25 18:34:51 mahoney kernel: [ 62.149635] lp: driver loaded but no devices found
Jan 25 18:34:51 mahoney kernel: [ 62.152549] ppdev: user-space parallel port driver
Jan 25 18:34:56 mahoney kernel: [ 66.969812] __ratelimit: 24 callbacks suppressed
Jan 25 18:34:56 mahoney kernel: [ 66.969815] type=1503 audit(1327534496.031:20): operation="capable" pid=1688 parent=1 profile="" name="dac_override"
Jan 25 19:00:07 mahoney kernel: [ 1578.150284] EXT4-fs (sdb1): mounted filesystem with ordered data mode
Jan 25 19:00:12 mahoney kernel: [ 1582.982446] EXT4-fs (sdd1): mounted filesystem with ordered data mode
Jan 25 19:00:15 mahoney kernel: [ 1585.649919] EXT4-fs (sdc1): mounted filesystem with ordered data mode
Jan 25 19:00:18 mahoney kernel: [ 1588.925371] EXT4-fs (sde1): mounted filesystem with ordered data mode
Jan 25 19:00:27 mahoney kernel: [ 1597.684356] EXT4-fs (sda1): mounted filesystem with ordered data mode
Jan 25 19:00:29 mahoney kernel: [ 1600.200280] EXT4-fs (sdg1): mounted filesystem with ordered data mode
Jan 25 19:01:43 mahoney kernel: [ 1673.772973] EXT4-fs (sdf1): mounted filesystem with ordered data mode
root@mahoney:~# lspci -vnn (edited)
0e:08.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic
53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI [1000:0030] (rev 08)
Subsystem: LSI Logic / Symbios Logic Device [1000:10b0]
Flags: bus master, 66MHz, medium devsel, latency 72, IRQ 16
I/O ports at cc00 [size=256]
Memory at fc5e0000 (64-bit, non-prefetchable) [size=128K]
Memory at fc5c0000 (64-bit, non-prefetchable) [size=128K]
Expansion ROM at fc600000 [disabled] [size=1M]
Capabilities: [50] Power Management version 2
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Capabilities: [68] PCI-X non-bridge device
Capabilities: [70] CompactPCI hot-swap <?>
Kernel driver in use: mptspi
Kernel modules: mptspi
0e:08.1 SCSI storage controller [0100]: LSI Logic / Symbios Logic
53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI [1000:0030] (rev 08)
Subsystem: LSI Logic / Symbios Logic Device [1000:10b0]
Flags: bus master, 66MHz, medium devsel, latency 72, IRQ 17
I/O ports at c800 [size=256]
Memory at fc5a0000 (64-bit, non-prefetchable) [size=128K]
Memory at fc580000 (64-bit, non-prefetchable) [size=128K]
Expansion ROM at d0100000 [disabled] [size=1M]
Capabilities: [50] Power Management version 2
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Capabilities: [68] PCI-X non-bridge device
Capabilities: [70] #00 [0000]
Kernel driver in use: mptspi
Kernel modules: mptspi