Hang when booting 3.1.0-1-686-pae and 2.6.38-1-686
My boot under 3.1.0-1-686-pae, 3.1.0-1-486, and 2.6.38-1-686 hangs with the
following screen:
http://i.imgur.com/ij3kG.jpg
Under 2.6.32-5-686 and 2.6.26-2-686 it's fine. Any ideas?
(It's an old Dell Inspiron 2650. I attach /proc/cpuinfo, lspci and dmesg
below)
Thanks,
Tom
% cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 2
model name : Mobile Intel(R) Pentium(R) 4 - M CPU 1.70GHz
stepping : 7
cpu MHz : 1200.000
cache size : 512 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov
pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe up pebs bts cid
bogomips : 2392.77
clflush size : 64
cache_alignment : 128
address sizes : 36 bits physical, 32 bits virtual
power management:
% sudo lspci -vvv # Under 2.6.32
00:00.0 Host bridge: Intel Corporation 82845 845 [Brookdale] Chipset Host
Bridge (rev 05)
Subsystem: Dell Device 00f3
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] Vendor Specific Information: Len=04 <?>
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW+
Rate=x1
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge: Intel Corporation 82845 845 [Brookdale] Chipset AGP
Bridge (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 96
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e0000000-e7ffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1d.0 USB Controller: Intel Corporation 82801CA/CAM USB Controller #1 (rev
02) (prog-if 00 [UHCI])
Subsystem: Dell Device 00f3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 1800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation 82801CA/CAM USB Controller #2 (rev
02) (prog-if 00 [UHCI])
Subsystem: Dell Device 00f3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 42)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=06, sec-latency=168
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e8000000-e80fffff
Prefetchable memory behind bridge: 20000000-25ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge: Intel Corporation 82801CAM ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface: Intel Corporation 82801CAM IDE U100 Controller (rev
02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Device 00f3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1840 [size=16]
Region 5: Memory at 26000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation 82801CA/CAM SMBus Controller (rev 02)
Subsystem: Dell Device 00f3
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: i801_smbus
00:1f.5 Multimedia audio controller: Intel Corporation 82801CA/CAM AC'97
Audio Controller (rev 02)
Subsystem: Dell Device 00f3
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 1880 [size=64]
Kernel driver in use: Intel ICH
00:1f.6 Modem: Intel Corporation 82801CA/CAM AC'97 Modem Controller (rev 02)
(prog-if 00 [Generic])
Subsystem: Conexant Systems, Inc. MD56ORD V.92 MDC Modem
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Kernel driver in use: Intel ICH Modem
01:00.0 VGA compatible controller: nVidia Corporation NV11 [GeForce2 Go]
(rev b2) (prog-if 00 [VGA controller])
Subsystem: Dell Device 00f3
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
[virtual] Expansion ROM at e1000000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
02:01.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
78)
Subsystem: Dell Device 00f3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 80 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 3000 [size=128]
Region 1: Memory at e8000000 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at 24000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: 3c59x
02:04.0 CardBus bridge: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus
Controller
Subsystem: Dell Device 00f3
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e8001000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 28000000-2bfff000
I/O window 0: 00003400-000034ff
I/O window 1: 00003800-000038ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+
PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
dmesg under 2.6.32:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-28)
(ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Nov
25 18:43:34 UTC 2010
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
[ 0.000000] BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
[ 0.000000] BIOS-e820: 000000001fef0000 - 000000001feff000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001feff000 - 000000001ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001ff00000 - 000000001ff80000 (usable)
[ 0.000000] BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.3 present.
[ 0.000000] last_pfn = 0x1ff80 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FE0000000 write-back
[ 0.000000] 1 base 01FF80000 mask FFFF80000 uncachable
[ 0.000000] 2 base 01FF80000 mask FFFF80000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] init_memory_mapping: 0000000000000000-000000001ff80000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 001fc00000 page 2M
[ 0.000000] 001fc00000 - 001ff80000 page 4k
[ 0.000000] kernel direct mapping tables up to 1ff80000 @ 7000-d000
[ 0.000000] RAMDISK: 1f0cf000 - 1f8ef932
[ 0.000000] ACPI: RSDP 000f6740 00014 (v00 DELL )
[ 0.000000] ACPI: RSDT 1fefadcf 00028 (v01 DELL RSDT 06040000 LTP
00000000)
[ 0.000000] ACPI: FACP 1fefef8c 00074 (v01 INTEL 845M 06040000 PTL
0000004B)
[ 0.000000] ACPI: DSDT 1fefadf7 04195 (v01 DELL 845M 06040000 MSFT
0100000D)
[ 0.000000] ACPI: FACS 1fefffc0 00040
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 511MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 1ff80000
[ 0.000000] low ram: 0 - 1ff80000
[ 0.000000] node 0 low ram: 00000000 - 1ff80000
[ 0.000000] node 0 bootmap 00002000 - 00005ff0
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 001ff80000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==>
[0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==>
[0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==>
[0000006000 - 0000007000]
[ 0.000000] #3 [0001000000 - 00014c7bb4] TEXT DATA BSS ==>
[0001000000 - 00014c7bb4]
[ 0.000000] #4 [001f0cf000 - 001f8ef932] RAMDISK ==>
[001f0cf000 - 001f8ef932]
[ 0.000000] #5 [000009f000 - 0000100000] BIOS reserved ==>
[000009f000 - 0000100000]
[ 0.000000] #6 [00014c8000 - 00014ce1bc] BRK ==>
[00014c8000 - 00014ce1bc]
[ 0.000000] #7 [0000007000 - 0000009000] PGTABLE ==>
[0000007000 - 0000009000]
[ 0.000000] #8 [0000002000 - 0000006000] BOOTMAP ==>
[0000002000 - 0000006000]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0001ff80
[ 0.000000] HighMem 0x0001ff80 -> 0x0001ff80
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0001fef0
[ 0.000000] 0: 0x0001ff00 -> 0x0001ff80
[ 0.000000] On node 0 totalpages: 130831
[ 0.000000] free_area_init_node: node 0, pgdat c13b2720, node_mem_map
c14d0000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3967 pages, LIFO batch:0
[ 0.000000] Normal zone: 991 pages used for memmap
[ 0.000000] Normal zone: 125841 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] APIC: disable apic facility
[ 0.000000] nr_irqs_gsi: 16
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 -
0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000001fef0000 -
000000001feff000
[ 0.000000] PM: Registered nosave memory: 000000001feff000 -
000000001ff00000
[ 0.000000] Allocating PCI resources starting at 20000000 (gap:
20000000:df800000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c1c00000 s34296 r0 d23048
u4194304
[ 0.000000] pcpu-alloc: s34296 r0 d23048 u4194304 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 129808
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686
root=UUID=152247fd-0eab-4e3d-bcc2-4a2cbe1ff331 ro quiet
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 505048k/523776k available (2500k kernel code, 17848k
reserved, 1324k data, 372k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0xe0780000 - 0xff3fe000 ( 492 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdff80000 ( 511 MB)
[ 0.000000] .init : 0xc13bd000 - 0xc141a000 ( 372 kB)
[ 0.000000] .data : 0xc1271019 - 0xc13bc320 (1324 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1271019 (2500 kB)
[ 0.000000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0,
CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1694.885 MHz processor.
[ 0.008008] Calibrating delay loop (skipped), value calculated using
timer frequency.. 3389.77 BogoMIPS (lpj=6779540)
[ 0.008043] Security Framework initialized
[ 0.008052] SELinux: Disabled at boot.
[ 0.008065] Mount-cache hash table entries: 512
[ 0.008290] Initializing cgroup subsys ns
[ 0.008298] Initializing cgroup subsys cpuacct
[ 0.008306] Initializing cgroup subsys devices
[ 0.008311] Initializing cgroup subsys freezer
[ 0.008316] Initializing cgroup subsys net_cls
[ 0.008363] CPU: Trace cache: 12K uops, L1 D cache: 8K
[ 0.008369] CPU: L2 cache: 512K
[ 0.008374] CPU: Hyper-Threading is disabled
[ 0.008381] mce: CPU supports 4 MCE banks
[ 0.008416] Performance Events: no PMU driver, software events only.
[ 0.008430] Checking 'hlt' instruction... OK.
[ 0.024665] SMP alternatives: switching to UP code
[ 0.034599] Freeing SMP alternatives: 13k freed
[ 0.034620] ACPI: Core revision 20090903
[ 0.042418] ACPI: setting ELCR to 0200 (from 0c00)
[ 0.044148] Enabling APIC mode: Flat. Using 0 I/O APICs
[ 0.044154] weird, boot CPU (#0) not listed by the BIOS.
[ 0.044157] SMP motherboard not detected.
[ 0.044160] Local APIC not detected. Using dummy APIC emulation.
[ 0.044164] SMP disabled
[ 0.044472] Brought up 1 CPUs
[ 0.044478] Total of 1 processors activated (3389.77 BogoMIPS).
[ 0.048065] CPU0 attaching NULL sched-domain.
[ 0.048268] devtmpfs: initialized
[ 0.049051] regulator: core version 0.5
[ 0.049145] NET: Registered protocol family 16
[ 0.049311] ACPI: bus type pci registered
[ 0.051646] PCI: PCI BIOS revision 2.10 entry at 0xfd9c5, last bus=2
[ 0.051650] PCI: Using configuration type 1 for base access
[ 0.052495] bio: create slab <bio-0> at 0
[ 0.053304] ACPI: EC: Look up EC in DSDT
[ 0.057452] ACPI: Interpreter enabled
[ 0.057462] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.057501] ACPI: Using PIC for interrupt routing
[ 0.064850] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
[ 0.065078] ACPI: No dock devices found.
[ 0.066137] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.066214] pci 0000:00:00.0: reg 10 32bit mmio pref:
[0xec000000-0xefffffff]
[ 0.066390] pci 0000:00:1d.0: reg 20 io port: [0x1800-0x181f]
[ 0.066465] pci 0000:00:1d.1: reg 20 io port: [0x1820-0x183f]
[ 0.066610] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH4
ACPI/GPIO/TCO
[ 0.066617] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH4
GPIO
[ 0.066658] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[ 0.066669] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[ 0.066680] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[ 0.066690] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[ 0.066701] pci 0000:00:1f.1: reg 20 io port: [0x1840-0x184f]
[ 0.066712] pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
[ 0.066784] pci 0000:00:1f.3: reg 20 io port: [0x1860-0x187f]
[ 0.066835] pci 0000:00:1f.5: reg 10 io port: [0x1c00-0x1cff]
[ 0.066846] pci 0000:00:1f.5: reg 14 io port: [0x1880-0x18bf]
[ 0.066913] pci 0000:00:1f.6: reg 10 io port: [0x2400-0x24ff]
[ 0.066924] pci 0000:00:1f.6: reg 14 io port: [0x2000-0x207f]
[ 0.067016] pci 0000:01:00.0: reg 10 32bit mmio: [0xe0000000-0xe0ffffff]
[ 0.067026] pci 0000:01:00.0: reg 14 32bit mmio pref:
[0xf0000000-0xf7ffffff]
[ 0.067053] pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x00ffff]
[ 0.067136] pci 0000:00:01.0: bridge 32bit mmio: [0xe0000000-0xe7ffffff]
[ 0.067144] pci 0000:00:01.0: bridge 32bit mmio pref:
[0xf0000000-0xf7ffffff]
[ 0.067195] pci 0000:02:01.0: reg 10 io port: [0x3000-0x307f]
[ 0.067206] pci 0000:02:01.0: reg 14 32bit mmio: [0xe8000000-0xe800007f]
[ 0.067239] pci 0000:02:01.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.067264] pci 0000:02:01.0: supports D1 D2
[ 0.067269] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.067276] pci 0000:02:01.0: PME# disabled
[ 0.067332] pci 0000:02:04.0: reg 10 32bit mmio: [0x000000-0x000fff]
[ 0.067359] pci 0000:02:04.0: supports D1 D2
[ 0.067363] pci 0000:02:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.067370] pci 0000:02:04.0: PME# disabled
[ 0.067426] pci 0000:00:1e.0: transparent bridge
[ 0.067433] pci 0000:00:1e.0: bridge io port: [0x3000-0x3fff]
[ 0.067441] pci 0000:00:1e.0: bridge 32bit mmio: [0xe8000000-0xe80fffff]
[ 0.067482] pci_bus 0000:00: on NUMA node 0
[ 0.067489] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.067729] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[ 0.067836] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.070476] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12 14
15)
[ 0.070673] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 *10 11 12 14
15)
[ 0.070838] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12 14
15) *0, disabled.
[ 0.071032] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14
15)
[ 0.071224] vgaarb: device added:
PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.071230] vgaarb: loaded
[ 0.071377] PCI: Using ACPI for IRQ routing
[ 0.071637] Switching to clocksource tsc
[ 0.072001] pnp: PnP ACPI init
[ 0.072001] ACPI: bus type pnp registered
[ 0.072468] pnp 00:04: mem resource (0x10000-0x1ffff) overlaps
0000:02:01.0 BAR 6 (0x0-0x1ffff), disabling
[ 0.076148] pnp: PnP ACPI: found 9 devices
[ 0.076153] ACPI: ACPI bus type pnp unregistered
[ 0.076162] PnPBIOS: Disabled by ACPI PNP
[ 0.076187] system 00:04: ioport range 0x600-0x60f has been reserved
[ 0.076194] system 00:04: ioport range 0x700-0x70f has been reserved
[ 0.076201] system 00:04: ioport range 0x1000-0x107f has been reserved
[ 0.076207] system 00:04: ioport range 0x1180-0x11bf has been reserved
[ 0.076213] system 00:04: ioport range 0x1200-0x120f has been reserved
[ 0.076219] system 00:04: ioport range 0xfe00-0xfe01 has been reserved
[ 0.076225] system 00:04: ioport range 0xfff0-0xfffe has been reserved
[ 0.076233] system 00:04: iomem range 0xfebffc00-0xfebfffff has been
reserved
[ 0.076239] system 00:04: iomem range 0xfff80000-0xffffffff has been
reserved
[ 0.111210] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.111215] pci 0000:00:01.0: IO window: disabled
[ 0.111223] pci 0000:00:01.0: MEM window: 0xe0000000-0xe7ffffff
[ 0.111231] pci 0000:00:01.0: PREFETCH window: 0xf0000000-0xf7ffffff
[ 0.111248] pci 0000:02:04.0: CardBus bridge, secondary bus 0000:03
[ 0.111253] pci 0000:02:04.0: IO window: 0x003400-0x0034ff
[ 0.111260] pci 0000:02:04.0: IO window: 0x003800-0x0038ff
[ 0.111267] pci 0000:02:04.0: PREFETCH window: 0x20000000-0x23ffffff
[ 0.111274] pci 0000:02:04.0: MEM window: 0x28000000-0x2bffffff
[ 0.111282] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
[ 0.111288] pci 0000:00:1e.0: IO window: 0x3000-0x3fff
[ 0.111297] pci 0000:00:1e.0: MEM window: 0xe8000000-0xe80fffff
[ 0.111304] pci 0000:00:1e.0: PREFETCH window: 0x20000000-0x25ffffff
[ 0.111331] pci 0000:00:1e.0: setting latency timer to 64
[ 0.111420] pci 0000:02:04.0: power state changed by ACPI to D0
[ 0.111464] pci 0000:02:04.0: power state changed by ACPI to D0
[ 0.111734] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[ 0.111738] PCI: setting IRQ 10 as level-triggered
[ 0.111747] pci 0000:02:04.0: PCI INT A -> Link[LNKA] -> GSI 10 (level,
low) -> IRQ 10
[ 0.111760] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.111765] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.111771] pci_bus 0000:01: resource 1 mem: [0xe0000000-0xe7ffffff]
[ 0.111777] pci_bus 0000:01: resource 2 pref mem [0xf0000000-0xf7ffffff]
[ 0.111782] pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
[ 0.111788] pci_bus 0000:02: resource 1 mem: [0xe8000000-0xe80fffff]
[ 0.111793] pci_bus 0000:02: resource 2 pref mem [0x20000000-0x25ffffff]
[ 0.111799] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.111804] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffff]
[ 0.111809] pci_bus 0000:03: resource 0 io: [0x3400-0x34ff]
[ 0.111814] pci_bus 0000:03: resource 1 io: [0x3800-0x38ff]
[ 0.111820] pci_bus 0000:03: resource 2 pref mem [0x20000000-0x23ffffff]
[ 0.111825] pci_bus 0000:03: resource 3 mem: [0x28000000-0x2bffffff]
[ 0.111891] NET: Registered protocol family 2
[ 0.112061] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.112606] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 0.112759] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.112892] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.112897] TCP reno registered
[ 0.113029] NET: Registered protocol family 1
[ 0.113121] pci 0000:01:00.0: Boot video device
[ 0.113228] Unpacking initramfs...
[ 0.608062] Freeing initrd memory: 8322k freed
[ 0.627320] audit: initializing netlink socket (disabled)
[ 0.627353] type=2000 audit(1326284080.624:1): initialized
[ 0.632263] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.634805] VFS: Disk quotas dquot_6.5.2
[ 0.634912] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.635050] msgmni has been set to 1003
[ 0.635411] alg: No test for stdrng (krng)
[ 0.635511] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.635518] io scheduler noop registered
[ 0.635522] io scheduler anticipatory registered
[ 0.635526] io scheduler deadline registered
[ 0.635596] io scheduler cfq registered (default)
[ 0.635913] isapnp: Scanning for PnP cards...
[ 0.990111] isapnp: No Plug & Play device found
[ 0.992753] Linux agpgart interface v0.103
[ 0.992879] agpgart-intel 0000:00:00.0: Intel 845G Chipset
[ 0.997013] agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xec000000
[ 0.997136] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.997958] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[ 0.997968] serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 10
(level, low) -> IRQ 10
[ 0.997979] serial 0000:00:1f.6: PCI INT B disabled
[ 0.998130] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64
irq 1,12
[ 1.011587] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.011600] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.011800] mice: PS/2 mouse device common for all mice
[ 1.011966] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
[ 1.011992] rtc0: alarms up to one month, y3k, 242 bytes nvram
[ 1.012014] cpuidle: using governor ladder
[ 1.012018] cpuidle: using governor menu
[ 1.012027] No iBFT detected.
[ 1.012793] TCP cubic registered
[ 1.013019] NET: Registered protocol family 10
[ 1.013834] lo: Disabled Privacy Extensions
[ 1.014415] Mobile IPv6
[ 1.014421] NET: Registered protocol family 17
[ 1.014447] Using IPI No-Shortcut mode
[ 1.014587] PM: Resume from disk failed.
[ 1.014612] registered taskstats version 1
[ 1.014889] rtc_cmos 00:01: setting system clock to 2012-01-11 12:14:41
UTC (1326284081)
[ 1.014938] Initalizing network drop monitor service
[ 1.014985] Freeing unused kernel memory: 372k freed
[ 1.015720] Write protecting the kernel text: 2504k
[ 1.015749] Write protecting the kernel read-only data: 920k
[ 1.042409] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 1.056297] udev[46]: starting version 164
[ 1.400962] SCSI subsystem initialized
[ 1.424402] usbcore: registered new interface driver usbfs
[ 1.424703] usbcore: registered new interface driver hub
[ 1.428969] usbcore: registered new device driver usb
[ 1.437353] Floppy drive(s): fd0 is 1.44M
[ 1.441314] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.486210] FDC 0 is a National Semiconductor PC87306
[ 1.496098] libata version 3.00 loaded.
[ 1.502175] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.502281] uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 10
(level, low) -> IRQ 10
[ 1.502303] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.502310] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.502370] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 1
[ 1.502409] uhci_hcd 0000:00:1d.0: irq 10, io base 0x00001800
[ 1.502492] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.502500] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.502509] usb usb1: Product: UHCI Host Controller
[ 1.502515] usb usb1: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.502522] usb usb1: SerialNumber: 0000:00:1d.0
[ 1.503795] usb usb1: configuration #1 chosen from 1 choice
[ 1.503962] hub 1-0:1.0: USB hub found
[ 1.503981] hub 1-0:1.0: 2 ports detected
[ 1.504487] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 1.504494] PCI: setting IRQ 11 as level-triggered
[ 1.504503] uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11
(level, low) -> IRQ 11
[ 1.504521] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.504527] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.504547] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 2
[ 1.504589] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820
[ 1.504655] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.504664] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.504673] usb usb2: Product: UHCI Host Controller
[ 1.504680] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.504687] usb usb2: SerialNumber: 0000:00:1d.1
[ 1.504974] usb usb2: configuration #1 chosen from 1 choice
[ 1.505098] hub 2-0:1.0: USB hub found
[ 1.505117] hub 2-0:1.0: 2 ports detected
[ 1.514547] 3c59x 0000:02:01.0: PCI INT A -> Link[LNKB] -> GSI 10 (level,
low) -> IRQ 10
[ 1.514583] 3c59x: Donald Becker and others.
[ 1.514596] 0000:02:01.0: 3Com PCI 3c905C Tornado at e097a000.
[ 1.543220] ata_piix 0000:00:1f.1: version 2.13
[ 1.543246] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[ 1.543585] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 1.543594] ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11
(level, low) -> IRQ 11
[ 1.543688] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.545638] scsi0 : ata_piix
[ 1.546911] scsi1 : ata_piix
[ 1.548218] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1840 irq
14
[ 1.548226] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1848 irq
15
[ 1.736431] ata2.00: ATAPI: TOSHIBA DVD-ROM SD-C2612, 1D21, max UDMA/33
[ 1.751394] ata1.00: ATA-8: WDC WD800BEVE-00A0HT0, 11.01A11, max UDMA/100
[ 1.751402] ata1.00: 156301488 sectors, multi 16: LBA48
[ 1.761456] ata1.00: configured for UDMA/100
[ 1.761654] scsi 0:0:0:0: Direct-Access ATA WDC WD800BEVE-00
11.0 PQ: 0 ANSI: 5
[ 1.768353] ata2.00: configured for UDMA/33
[ 1.777300] scsi 1:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-C2612
1D21 PQ: 0 ANSI: 5
[ 1.805868] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0
GB/74.5 GiB)
[ 1.805976] sd 0:0:0:0: [sda] Write Protect is off
[ 1.805983] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.806029] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.806304] sda: sda1 sda2 <
[ 1.816057] usb 2-1: new low speed USB device using uhci_hcd and address
2
[ 1.839543] sda5 >
[ 1.840777] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.861498] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 1.861507] Uniform CD-ROM driver Revision: 3.20
[ 1.861740] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.878165] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.879047] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.991603] usb 2-1: New USB device found, idVendor=046d, idProduct=c016
[ 1.991612] usb 2-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 1.991617] usb 2-1: Product: Optical USB Mouse
[ 1.991622] usb 2-1: Manufacturer: Logitech
[ 1.991806] usb 2-1: configuration #1 chosen from 1 choice
[ 2.019692] usbcore: registered new interface driver hiddev
[ 2.033501] input: Logitech Optical USB Mouse as
/devices/pci0000:00/0000:00:1d.1/usb2/2-1/2-1:1.0/input/input1
[ 2.034352] generic-usb 0003:046D:C016.0001: input,hidraw0: USB HID v1.10
/ Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.1-1/input0
[ 2.034498] usbcore: registered new interface driver usbhid
[ 2.035039] usbhid: v2.6:USB HID core driver
[ 2.170322] PM: Starting manual resume from disk
[ 2.170332] PM: Resume from partition 8:5
[ 2.170335] PM: Checking hibernation image.
[ 2.170659] PM: Error -22 checking image file
[ 2.170663] PM: Resume from disk failed.
[ 2.231764] kjournald starting. Commit interval 5 seconds
[ 2.231784] EXT3-fs: mounted filesystem with ordered data mode.
[ 3.933386] udev[255]: starting version 164
[ 4.764120] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 4.770086] Marking TSC unstable due to TSC halts in idle
[ 4.793425] processor LNXCPU:00: registered as cooling_device0
[ 4.794087] input: Lid Switch as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input3
[ 4.803219] Switching to clocksource acpi_pm
[ 4.814855] dcdbas dcdbas: Dell Systems Management Base Driver (version
5.6.0-3.2)
[ 4.815106] ACPI: AC Adapter [ACAD] (on-line)
[ 4.815816] ACPI: Lid Switch [LID]
[ 4.817239] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4
[ 4.817562] ACPI: Power Button [PWRB]
[ 4.819361] input: Sleep Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input5
[ 4.819604] ACPI: Sleep Button [SLPB]
[ 4.819843] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
[ 4.819968] ACPI: Power Button [PWRF]
[ 5.377367] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.393423] input: Video Bus as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:00/LNXVIDEO:00/input/input7
[ 5.393683] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 5.416524] ACPI: Battery Slot [BAT1] (battery present)
[ 5.507698] parport_pc 00:07: reported by Plug and Play ACPI
[ 5.507786] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 5.523259] intel_rng: FWH not detected
[ 5.531922] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 5.542961] i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 10
(level, low) -> IRQ 10
[ 6.122656] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x254ab1, caps:
0x804713/0x0/0x0
[ 6.180486] input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio1/input/input8
[ 6.585568] yenta_cardbus 0000:02:04.0: CardBus bridge found [1028:00f3]
[ 6.585597] yenta_cardbus 0000:02:04.0: O2: res at 0x94/0xD4: 00/c8
[ 6.585604] yenta_cardbus 0000:02:04.0: O2: enabling read prefetch/write
burst
[ 6.634647] Error: Driver 'pcspkr' is already registered, aborting...
[ 6.696831] Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI
10 (level, low) -> IRQ 10
[ 6.696865] Intel ICH Modem 0000:00:1f.6: setting latency timer to 64
[ 6.712868] yenta_cardbus 0000:02:04.0: ISA IRQ mask 0x0038, PCI irq 10
[ 6.712876] yenta_cardbus 0000:02:04.0: Socket status: 30000007
[ 6.712884] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02)
from #02 to #06
[ 6.712904] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge I/O
window: 0x3000 - 0x3fff
[ 6.712915] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x3000-0x3fff: clean.
[ 6.713345] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge Memory
window: 0xe8000000 - 0xe80fffff
[ 6.713355] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge Memory
window: 0x20000000 - 0x25ffffff
[ 6.812088] MC'97 1 converters and GPIO not ready (0xff00)
[ 6.813205] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 10
(level, low) -> IRQ 10
[ 6.813235] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 7.337306] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
clean.
[ 7.339404] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
excluding 0x4d0-0x4d7
[ 7.343644] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
clean.
[ 7.344477] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
clean.
[ 7.345511] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
clean.
[ 7.392054] intel8x0_measure_ac97_clock: measured 55313 usecs (2658
samples)
[ 7.392061] intel8x0: clocking to 48000
[ 8.439802] Adding 1510068k swap on /dev/sda5. Priority:-1 extents:1
across:1510068k
[ 8.650024] EXT3 FS on sda1, internal journal
[ 8.848464] loop: module loaded
[ 9.904865] eth0: setting half-duplex.
[ 9.906317] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.050011] apm: BIOS not found.
[ 417.904801] eth0: setting full-duplex.
[ 417.904931] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 428.592054] eth0: no IPv6 routers present
Reply to: