Bug#647858: linux-image-3.0.0-1-686-pae: loading kernel module viafb blacks out Sylvania G netbook
Package: linux-2.6 Version: 3.0.0-3
Severity: important
Dear Maintainer,
System in question is a Sylvania G netbook. It is an older model based
on a VIA CPU (C7-M, CX700/VX700 UniChrome display card).
Running 'modprobe viafb' will blank the screen and also aparantly
completely hang the system. I worked around this by putting:
install viafb /bin/false
in a modprobe.d file.
Once this is out of the way I manage to get a display running.
I still seem to get the system hung after a while. This seems to be when
the screen is blaked-out, but I'm not really sure yet.
Hanging the display by loading viafb was also reproduced with kernel
2.6.32-5-686, which is the oldest one I have on the system.
-- Package-specific info:
** Version:
Linux version 3.0.0-1-686-pae (Debian 3.0.0-3) (ben@decadent.org.uk) (gcc version 4.5.3 (Debian 4.5.3-8) ) #1 SMP Sat Aug 27 16:41:03 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.0.0-1-686-pae root=UUID=68486314-a888-42c0-907a-672a1aa79782 ro quiet
** Not tainted
** Kernel log:
[ 5.484047] usb 1-4: new high speed USB device number 2 using ehci_hcd
[ 5.500462] ata2.00: configured for UDMA/33
[ 5.501128] scsi 1:0:0:0: Direct-Access ATA ST730212DE 3.01 PQ: 0 ANSI: 5
[ 5.533600] sd 1:0:0:0: [sda] 58605120 512-byte logical blocks: (30.0 GB/27.9 GiB)
[ 5.533821] sd 1:0:0:0: [sda] Write Protect is off
[ 5.533842] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.533939] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.623031] usb 1-4: New USB device found, idVendor=0bda, idProduct=8187
[ 5.623054] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.623071] usb 1-4: Product: RTL8187_Wireless
[ 5.623086] usb 1-4: Manufacturer: Manufacturer_Realtek_RTL8187_
[ 5.623101] usb 1-4: SerialNumber: 0015AFC014DC
[ 5.625686] sda: sda1 sda2 < sda5 >
[ 5.628875] sd 1:0:0:0: [sda] Attached SCSI disk
[ 5.655524] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 5.740080] usb 1-5: new high speed USB device number 3 using ehci_hcd
[ 6.118879] usb 1-5: New USB device found, idVendor=5986, idProduct=0101
[ 6.118904] usb 1-5: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 6.118922] usb 1-5: Product: USB2.0 Camera
[ 6.240070] usb 1-6: new high speed USB device number 4 using ehci_hcd
[ 6.387509] usb 1-6: New USB device found, idVendor=0bda, idProduct=0158
[ 6.387533] usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.387550] usb 1-6: Product: USB2.0-CRW
[ 6.387564] usb 1-6: Manufacturer: Generic
[ 6.387578] usb 1-6: SerialNumber: 20060413092100000
[ 6.417541] usbcore: registered new interface driver uas
[ 6.425897] Initializing USB Mass Storage driver...
[ 6.427032] usbcore: registered new interface driver usb-storage
[ 6.427049] USB Mass Storage support registered.
[ 6.431315] scsi2 : usb-storage 1-6:1.0
[ 6.432124] usbcore: registered new interface driver ums-realtek
[ 6.591272] PM: Starting manual resume from disk
[ 6.591293] PM: Hibernation image partition 8:5 present
[ 6.591305] PM: Looking for hibernation image.
[ 6.591895] PM: Image not found (code -22)
[ 6.591908] PM: Hibernation image not present or could not be loaded.
[ 6.628856] EXT3-fs (sda1): recovery required on readonly filesystem
[ 6.628877] EXT3-fs (sda1): write access will be enabled during recovery
[ 6.645201] EXT3-fs: barriers not enabled
[ 7.444500] scsi 2:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
[ 7.456871] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 7.462111] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 13.092912] kjournald starting. Commit interval 5 seconds
[ 13.093248] EXT3-fs (sda1): recovery complete
[ 13.112402] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 17.012510] udevd[236]: starting version 172
[ 18.441785] ACPI: acpi_idle registered with cpuidle
[ 18.442170] Marking TSC unstable due to TSC halts in idle
[ 18.450889] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 18.450923] ACPI: Power Button [PWRB]
[ 18.451377] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 18.451498] ACPI: Lid Switch [LID]
[ 18.451865] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 18.451890] ACPI: Power Button [PWRF]
[ 18.470152] Switching to clocksource acpi_pm
[ 19.005540] ACPI: Battery Slot [BAT0] (battery present)
[ 19.009428] ACPI: AC Adapter [ACAD] (on-line)
[ 19.258649] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:14/LNXVIDEO:00/input/input4
[ 19.258694] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 19.462305] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 19.701002] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 19.723137] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 19.884610] Linux media interface: v0.10
[ 20.175598] Linux video capture interface: v2.00
[ 20.333677] uvcvideo: Found UVC 1.00 device USB2.0 Camera (5986:0101)
[ 20.351551] input: USB2.0 Camera as /devices/pci0000:00/0000:00:10.4/usb1/1-5/1-5:1.0/input/input6
[ 20.356123] usbcore: registered new interface driver uvcvideo
[ 20.356140] USB Video Class driver (v1.1.0)
[ 20.393131] Error: Driver 'pcspkr' is already registered, aborting...
[ 20.504182] cfg80211: Calling CRDA to update world regulatory domain
[ 20.583631] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1c0b1, caps: 0xa04750/0x200000/0x0
[ 20.644614] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input7
[ 20.939036] HDA Intel 0000:02:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 20.939172] HDA Intel 0000:02:01.0: irq 40 for MSI/MSI-X
[ 20.939251] HDA Intel 0000:02:01.0: setting latency timer to 64
[ 20.939270] HDA Intel 0000:02:01.0: PCI: Disallowing DAC for device
[ 22.442245] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 22.445651] ieee80211 phy0: hwaddr 00:15:af:c0:14:dc, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2
[ 22.475705] rtl8187: Customer ID is 0x00
[ 22.478639] Registered led device: rtl8187-phy0::radio
[ 22.482442] Registered led device: rtl8187-phy0::tx
[ 22.485498] Registered led device: rtl8187-phy0::rx
[ 22.486696] rtl8187: wireless switch is on
[ 22.488283] usbcore: registered new interface driver rtl8187
[ 24.911703] Adding 1238012k swap on /dev/sda5. Priority:-1 extents:1 across:1238012k
[ 25.708196] EXT3-fs (sda1): using internal journal
[ 26.083808] loop: module loaded
[ 29.272128] fuse init (API version 7.16)
[ 40.387076] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 40.442981] 8139too 0000:03:09.0: eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 43.864492] [drm] Initialized drm 1.1.0 20060810
[ 43.937276] pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 43.941600] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 43.941621] [drm] No driver support for vblank timestamp query.
[ 43.941644] [drm] Initialized via 2.11.1 20070202 for 0000:01:00.0 on minor 0
[ 44.056948] agpgart-via 0000:00:00.0: AGP 3.5 bridge
[ 44.057014] agpgart-via 0000:00:00.0: putting AGP V3 device into 8x mode
[ 44.057134] pci 0000:01:00.0: putting AGP V3 device into 8x mode
[ 50.848062] eth0: no IPv6 routers present
[ 105.747250] mtrr: no MTRR for a0000000,4000000 found
** Model information
not available
** Loaded modules:
Module Size Used by
via 34755 0
drm 129847 1 via
fuse 56331 1
loop 17866 0
i2c_algo_bit 12722 0
arc4 12418 2
rtl8187 30895 0
mac80211 165768 1 rtl8187
snd_hda_codec_via 48131 1
snd_hda_intel 21691 0
joydev 17006 0
snd_hda_codec 58364 2 snd_hda_codec_via,snd_hda_intel
snd_hwdep 12936 1 snd_hda_codec
cfg80211 112970 2 rtl8187,mac80211
uvcvideo 56927 0
snd_pcm 53315 2 snd_hda_intel,snd_hda_codec
rfkill 18522 1 cfg80211
videodev 61530 1 uvcvideo
snd_timer 22027 1 snd_pcm
snd 38562 6 snd_hda_codec_via,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
i2c_viapro 12451 0
soundcore 12992 1 snd
eeprom_93cx6 12423 1 rtl8187
media 13692 2 uvcvideo,videodev
evdev 12995 5
i2c_core 19141 4 drm,i2c_algo_bit,videodev,i2c_viapro
shpchp 26759 0
pci_hotplug 26736 1 shpchp
snd_page_alloc 12899 2 snd_hda_intel,snd_pcm
psmouse 46216 0
pcspkr 12515 0
video 17475 0
serio_raw 12734 0
ac 12552 0
battery 12957 0
power_supply 13283 2 ac,battery
button 12810 0
processor 27382 1
ext3 99597 1
jbd 42027 1 ext3
mbcache 12898 1 ext3
ums_realtek 12662 0
usb_storage 35164 1 ums_realtek
uas 13099 0
sg 21564 0
sd_mod 35493 3
crc_t10dif 12332 1 sd_mod
ata_generic 12439 0
pata_via 12733 2
libata 133339 2 ata_generic,pata_via
uhci_hcd 22275 0
ehci_hcd 35401 0
scsi_mod 135178 5 usb_storage,uas,sg,sd_mod,libata
usbcore 104234 8 rtl8187,uvcvideo,ums_realtek,usb_storage,uas,uhci_hcd,ehci_hcd
8139too 22108 0
8139cp 22301 0
mii 12595 2 8139too,8139cp
fan 12594 0
thermal 13138 0
thermal_sys 17677 4 video,processor,fan,thermal
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. CX700/VX700 Host Bridge [1106:0324] (rev 10)
Subsystem: VIA Technologies, Inc. CX700/VX700 Host Bridge [1106:0324]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Capabilities: <access denied>
Kernel driver in use: agpgart-via
00:00.1 Host bridge [0600]: VIA Technologies, Inc. CX700/VX700 Host Bridge [1106:1324]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.2 Host bridge [0600]: VIA Technologies, Inc. CX700/VX700 Host Bridge [1106:2324]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 Host bridge [0600]: VIA Technologies, Inc. CX700/VX700 Host Bridge [1106:3324]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.4 Host bridge [0600]: VIA Technologies, Inc. CX700/VX700 Host Bridge [1106:4324]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.7 Host bridge [0600]: VIA Technologies, Inc. CX700/VX700 Host Bridge [1106:7324]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d0000000-d0ffffff
Prefetchable memory behind bridge: a0000000-bfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:0f.0 IDE interface [0101]: VIA Technologies, Inc. CX700/VX700 RAID Controller [1106:0581] (prog-if 8a [Master SecP PriP])
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d90]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at 4460 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_via
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 90) (prog-if 00 [UHCI])
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d90]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 4400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 90) (prog-if 00 [UHCI])
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d90]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 22
Region 4: I/O ports at 4420 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 90) (prog-if 00 [UHCI])
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d90]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 4440 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 90) (prog-if 20 [EHCI])
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d90]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 23
Region 0: Memory at d1400000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. CX700/VX700 PCI to ISA Bridge [1106:8324]
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d90]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:11.7 Host bridge [0600]: VIA Technologies, Inc. CX700/VX700 Internal Module Bus [1106:324e]
Subsystem: VIA Technologies, Inc. CX700/VX700 Internal Module Bus [1106:324e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 8
Capabilities: <access denied>
00:13.0 PCI bridge [0604]: VIA Technologies, Inc. CX700/VX700 Host Bridge [1106:324b] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: d1000000-d10fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:13.1 PCI bridge [0604]: VIA Technologies, Inc. CX700/VX700 PCI to PCI Bridge [1106:324a] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00005000-00005fff
Memory behind bridge: d1100000-d11fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. CX700/VX700 [S3 UniChrome Pro] [1106:3157] (rev 03) (prog-if 00 [VGA controller])
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d30]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (500ns min)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at a0000000 (32-bit, prefetchable) [size=512M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
02:01.0 Audio device [0403]: VIA Technologies, Inc. VT1708/A [Azalia HDAC] (VIA High Definition Audio Controller) [1106:3288] (rev 10)
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d40]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 40
Region 0: Memory at d1000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
03:09.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: FIRST INTERNATIONAL Computer Inc Device [1509:2d20]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 5000 [size=256]
Region 1: Memory at d1100000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: 8139too
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter
Bus 001 Device 003: ID 5986:0101 Acer, Inc USB2.0 Camera
Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.0.0-1-686-pae (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.0.0-1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.40
ii initramfs-tools [linux-initramfs-tool] 0.99
ii linux-base 3.3
ii module-init-tools 3.16-1
Versions of packages linux-image-3.0.0-1-686-pae recommends:
ii firmware-linux-free 3
ii libc6-i686 2.13-21
Versions of packages linux-image-3.0.0-1-686-pae suggests:
pn grub-pc 1.99-12
pn linux-doc-3.0.0 <none>
Versions of packages linux-image-3.0.0-1-686-pae is related to:
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.0.0-1-686-pae/prerm/removing-running-kernel-3.0.0-1-686-pae: true
linux-image-3.0.0-1-686-pae/postinst/ignoring-ramdisk:
linux-image-3.0.0-1-686-pae/postinst/missing-firmware-3.0.0-1-686-pae:
linux-image-3.0.0-1-686-pae/postinst/depmod-error-initrd-3.0.0-1-686-pae: false
--
Tzafrir Cohen | tzafrir@jabber.org | VIM is
http://tzafrir.org.il | | a Mutt's
tzafrir@cohens.org.il | | best
tzafrir@debian.org | | friend
Reply to: