--- Begin Message ---
Package: linux-2.6
Version: 3.0.0-3
Severity: normal
Hi,
I installed a internal multi-card reader "Alcor Flash Card Reader / Writer" on my computer, it is recognized, the icons of readers appear in Nautius.
lsusb:
Bus 001 Device 003: ID 058f:6362 Alcor Micro Corp. Flash Card Reader/Writer
kernel logs:
[ 1.572030] usb 1-5: new high speed USB device number 3 using ehci_hcd
[ 1.706377] usb 1-5: New USB device found, idVendor=058f, idProduct=6362
[ 1.706451] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.706513] usb 1-5: Product: Mass Storage Device
[ 1.706568] usb 1-5: Manufacturer: Generic
[ 1.706621] usb 1-5: SerialNumber: 058F312D81B
[ 1.711449] usbcore: registered new interface driver uas
[ 1.713024] Initializing USB Mass Storage driver...
[ 1.713359] scsi4 : usb-storage 1-5:1.0
[ 1.713555] usbcore: registered new interface driver usb-storage
[ 1.713618] USB Mass Storage support registered.
[ 2.712816] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 2.713435] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 2.714057] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 2.714683] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 2.756405] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 2.756687] sd 4:0:0:1: Attached scsi generic sg3 type 0
[ 2.756956] sd 4:0:0:2: Attached scsi generic sg4 type 0
[ 2.757292] sd 4:0:0:3: Attached scsi generic sg5 type 0
[ 2.763170] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 2.763918] sd 4:0:0:3: [sde] Attached SCSI removable disk
[ 2.764544] sd 4:0:0:1: [sdc] Attached SCSI removable disk
[ 2.765289] sd 4:0:0:2: [sdd] Attached SCSI removable disk
When I plug an SD card, the green LED of the card reader lights up, but nothing appears in the logs.
The insertion of the card is not detected by Linux, the cards are not available.
I tested the same card reader with Windows, and cards are read
I also have an external card reader that plugs into a USB port. Linux detects the card and can read them.
This card reader also has a USB port, when I plug a USB key is recognized, mounted and accessible.
Regards.
-- Package-specific info:
** Version:
Linux version 3.0.0-1-686-pae (Debian 3.0.0-3) (ben@decadent.org.uk) (gcc version 4.5.3 (Debian 4.5.3-8) ) #1 SMP Sat Aug 27 16:41:03 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.0.0-1-686-pae root=UUID=5b77c12a-d076-4d52-9307-57c3fe25832a ro
** Not tainted
** Kernel log:
[ 6.283069] leds_ss4200: no LED devices found
[ 6.287697] ath5k 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 6.287710] ath5k 0000:01:00.0: setting latency timer to 64
[ 6.287763] ath5k 0000:01:00.0: registered as 'phy0'
[ 6.767911] Console: switching to colour frame buffer device 210x65
[ 6.776930] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 6.797678] fb0: inteldrmfb frame buffer device
[ 6.797681] drm: registered panic notifier
[ 6.798257] ath: EEPROM regdomain: 0x37
[ 6.798260] ath: EEPROM indicates we should expect a direct regpair map
[ 6.798263] ath: Country alpha2 being used: AW
[ 6.798265] ath: Regpair used: 0x37
[ 6.799306] No ACPI video bus found
[ 6.799510] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 6.799618] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 6.947302] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 6.948338] ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[ 7.389422] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.389537] HDA Intel 0000:00:1b.0: irq 46 for MSI/MSI-X
[ 7.389574] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 7.542958] audit: name_count maxed, losing inode data: dev=00:05, inode=4456
[ 7.543004] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 7.543011] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 7.543061] audit: name_count maxed, losing inode data: dev=00:05, inode=2994
[ 7.543069] audit: name_count maxed, losing inode data: dev=00:05, inode=2994
[ 7.543138] audit: name_count maxed, losing inode data: dev=00:05, inode=2994
[ 7.543148] audit: name_count maxed, losing inode data: dev=00:05, inode=2994
[ 7.543198] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 7.543205] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 7.704440] cfg80211: World regulatory domain updated:
[ 7.704492] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.704560] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.704625] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 7.704689] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 7.704753] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.704817] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.705263] cfg80211: Calling CRDA for country: AW
[ 7.778022] cfg80211: Regulatory domain changed to country: AW
[ 7.778081] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.778150] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 7.778212] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 7.778274] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 7.778336] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 7.778411] cfg80211: Calling CRDA for country: FR
[ 7.799455] cfg80211: Regulatory domain changed to country: FR
[ 7.799507] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.799568] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 7.799624] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 7.799678] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 7.799733] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 8.073035] Adding 2650688k swap on /dev/sda5. Priority:-1 extents:1 across:2650688k
[ 8.079786] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 8.209882] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,acl,user_xattr
[ 8.268731] audit: name_count maxed, losing inode data: dev=00:06, inode=3681
[ 8.268738] audit: name_count maxed, losing inode data: dev=00:06, inode=3681
[ 8.268750] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.268757] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.268862] audit: name_count maxed, losing inode data: dev=00:06, inode=9
[ 8.270608] audit: name_count maxed, losing inode data: dev=00:06, inode=3684
[ 8.270628] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.270637] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.270771] audit: name_count maxed, losing inode data: dev=00:06, inode=9
[ 8.270777] audit: name_count maxed, losing inode data: dev=00:06, inode=3689
[ 8.270790] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.270797] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.270898] audit: name_count maxed, losing inode data: dev=00:06, inode=9
[ 8.270904] audit: name_count maxed, losing inode data: dev=00:06, inode=3692
[ 8.270915] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.270922] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.271022] audit: name_count maxed, losing inode data: dev=00:06, inode=9
[ 8.271031] audit: name_count maxed, losing inode data: dev=00:06, inode=3695
[ 8.271043] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.271050] audit: name_count maxed, losing inode data: dev=00:05, inode=3
[ 8.271119] loop: module loaded
[ 9.978214] auditd (887): /proc/887/oom_adj is deprecated, please use /proc/887/oom_score_adj instead.
[ 11.214057] NET4: DECnet for Linux: V.2.5.68s (C) 1995-2003 Linux DECnet Project Team
[ 11.216685] DECnet: Routing cache hash table of 1024 buckets, 8Kbytes
[ 11.218869] NET: Registered protocol family 12
[ 11.504751] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.169607] RPC: Registered named UNIX socket transport module.
[ 12.172091] RPC: Registered udp transport module.
[ 12.174245] RPC: Registered tcp transport module.
[ 12.176385] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 12.275768] FS-Cache: Loaded
[ 12.335829] FS-Cache: Netfs 'nfs' registered for caching
[ 12.376273] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 13.684775] fuse init (API version 7.16)
[ 14.217032] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 14.219570] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 18.592977] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 24.640013] eth0: no IPv6 routers present
[ 27.159828] lp: driver loaded but no devices found
[ 27.713925] ppdev: user-space parallel port driver
[ 33.464064] device eth0 entered promiscuous mode
[ 56.443137] type=1305 audit(1320050234.874:9941): auid=4294967295 ses=4294967295 op="remove rule" key=(null) list=4 res=0
[ 56.443149] type=1305 audit(1320050234.874:9942): audit_enabled=0 old=1 auid=4294967295 ses=4294967295 res=1
[ 500.213818] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,acl,user_xattr,commit=0
[ 512.980093] hda-intel: Invalid position buffer, using LPIB read method instead.
[ 513.565012] hda-intel: Invalid position buffer, using LPIB read method instead.
[55430.215537] ip_tables: (C) 2000-2006 Netfilter Core Team
** Model information
not available
** Loaded modules:
Module Size Used by
iptable_filter 12488 0
ip_tables 17149 1 iptable_filter
x_tables 18076 2 iptable_filter,ip_tables
acpi_cpufreq 12865 1
mperf 12421 1 acpi_cpufreq
cpufreq_conservative 12987 0
cpufreq_stats 12758 0
cpufreq_userspace 12520 0
cpufreq_powersave 12422 0
parport_pc 22059 0
ppdev 12651 0
lp 12894 0
parport 27241 3 parport_pc,ppdev,lp
binfmt_misc 12880 1
autofs4 22873 0
fuse 56331 1
nfsd 197906 2
nfs 218412 1
lockd 61314 2 nfsd,nfs
fscache 31952 1 nfs
auth_rpcgss 32183 2 nfsd,nfs
nfs_acl 12463 2 nfsd,nfs
sunrpc 139050 19 nfsd,nfs,lockd,auth_rpcgss,nfs_acl
decnet 51703 0 [permanent]
loop 17866 0
snd_hda_codec_realtek 206339 1
snd_hda_intel 21691 4
snd_hda_codec 58364 2 snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 12936 1 snd_hda_codec
snd_pcm_oss 36377 0
snd_mixer_oss 17713 1 snd_pcm_oss
snd_pcm 53315 4 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_midi 12744 0
snd_rawmidi 22621 1 snd_seq_midi
snd_seq_midi_event 13124 1 snd_seq_midi
snd_seq 39539 2 snd_seq_midi,snd_seq_midi_event
arc4 12418 2
snd_timer 22027 2 snd_pcm,snd_seq
snd_seq_device 12985 3 snd_seq_midi,snd_rawmidi,snd_seq
evdev 12995 7
pcspkr 12515 0
i2c_i801 12670 0
ath5k 119541 0
ath 17181 1 ath5k
mac80211 165768 1 ath5k
rng_core 12616 0
snd 38562 18 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
cfg80211 112970 3 ath5k,ath,mac80211
rfkill 18522 1 cfg80211
i915 294451 2
drm_kms_helper 22688 1 i915
drm 129847 3 i915,drm_kms_helper
asus_atk0110 17110 0
i2c_algo_bit 12722 1 i915
soundcore 12992 1 snd
snd_page_alloc 12899 2 snd_hda_intel,snd_pcm
button 12810 1 i915
i2c_core 19141 5 i2c_i801,i915,drm_kms_helper,drm,i2c_algo_bit
video 17475 1 i915
processor 27382 1 acpi_cpufreq
thermal_sys 17677 2 video,processor
ext4 274801 1
mbcache 12898 1 ext4
jbd2 56798 1 ext4
crc16 12327 1 ext4
usbhid 31584 0
hid 60152 1 usbhid
usb_storage 35164 0
uas 13099 0
sg 21564 0
sr_mod 17478 0
sd_mod 35493 3
cdrom 34689 1 sr_mod
crc_t10dif 12332 1 sd_mod
ata_generic 12439 0
uhci_hcd 22275 0
ata_piix 21110 3
floppy 48297 0
libata 133339 2 ata_generic,ata_piix
ehci_hcd 35401 0
e1000e 113644 0
scsi_mod 135178 6 usb_storage,uas,sg,sr_mod,sd_mod,libata
usbcore 104234 6 usbhid,usb_storage,uas,uhci_hcd,ehci_hcd
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82946GZ/PL/GL Memory Controller Hub [8086:2970] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:823b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 82946GZ/GL Integrated Graphics Controller [8086:2972] (rev 02) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:823b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 45
Region 0: Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at dc00 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: ASUSTeK Computer Inc. Device [1043:8249]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 46
Region 0: Memory at fe8f8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Prefetchable memory behind bridge: 0000000080200000-00000000803fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.2 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 3 [8086:27d4] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 0000000080000000-00000000801fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM,P5LD2-VM Mainboard [1043:8179]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe8f7c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01)
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: ata_piix
00:1f.2 IDE interface [0101]: Intel Corporation N10/ICH7 Family SATA IDE Controller [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at d080 [size=8]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at cc00 [size=8]
Region 3: I/O ports at c880 [size=4]
Region 4: I/O ports at c800 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 01)
Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) [168c:001c] (rev 01)
Subsystem: AzureWave Device [1a3b:1034]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at feaf0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath5k
02:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Intel Corporation Gigabit CT Desktop Adapter [8086:a01f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at febe0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at feb00000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at ec00 [size=32]
Region 3: Memory at febdc000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at feb80000 [disabled] [size=256K]
Capabilities: <access denied>
Kernel driver in use: e1000e
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 058f:6362 Alcor Micro Corp. Flash Card Reader/Writer
Bus 002 Device 002: ID 046d:c044 Logitech, Inc. LX3 Optical Mouse
-- System Information:
Debian Release: wheezy/sid
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'testing'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 3.0.0-1-686-pae (SMP w/2 CPU cores)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.0.0-1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.40
ii initramfs-tools [linux-initramfs-tool] 0.99
ii linux-base 3.3
ii module-init-tools 3.16-1
Versions of packages linux-image-3.0.0-1-686-pae recommends:
ii firmware-linux-free 3
ii libc6-i686 2.13-21
Versions of packages linux-image-3.0.0-1-686-pae suggests:
pn grub-pc 1.99-12
pn linux-doc-3.0.0 <none>
Versions of packages linux-image-3.0.0-1-686-pae is related to:
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-linux 0.33
pn firmware-linux-nonfree 0.33
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.0.0-1-686-pae/postinst/ignoring-ramdisk:
linux-image-3.0.0-1-686-pae/postinst/missing-firmware-3.0.0-1-686-pae:
linux-image-3.0.0-1-686-pae/prerm/removing-running-kernel-3.0.0-1-686-pae: true
linux-image-3.0.0-1-686-pae/postinst/depmod-error-initrd-3.0.0-1-686-pae: false
--- End Message ---