Bug#653331: linux-image-3.1.0-1-686-pae: CPU#0 stuck for 23s, system does not boot
Package: linux-2.6
Version: 3.1.1-1
Severity: critical
Justification: breaks the whole system
Dear Maintainer,
First of all, thanks for looking into this..
I've installed debian-stable with 2.6.32 kernel.
After that, I made the upgrade to wheezy. From that moment on,
the system no longer boots: http://tinypic.com/r/2u9222q/5
"BUG: soft lockup - CPU#0 stuck for 23s! [swapper:1]"
This messages keeps repeating.
When I boot the 2.6.32 kernel, the system works.
Hardware is an old Asus A1300 laptop with SiS 630 chipset
and Pentium III 1Ghz CPU. Disabling APIC (apic=off) had no effect,
having cpufreqd installed or not also makes no difference.
I had found these suggestions on the net for similar but different problems.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
** PCI devices:
00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 630 Host [1039:0630] (rev 31)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
Region 0: Memory at d4000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: agpgart-sis
00:00.1 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 IDE Controller [1039:5513] (rev d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller (A,B step) [1039:5513]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at d800 [size=16]
Kernel driver in use: pata_sis
00:01.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge) [1039:0018]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 Ethernet controller [0200]: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet [1039:0900] (rev 82)
Subsystem: ASUSTeK Computer Inc. Device [1043:1455]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at d3800000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 28000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: sis900
00:01.2 USB controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 5
Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:01.3 USB controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 07) (prog-if 10 [OHCI])
Subsystem: Silicon Integrated Systems [SiS] Onboard USB Controller [1039:7000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (20000ns max), Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 5
Region 0: Memory at d2800000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:01.4 Multimedia audio controller [0401]: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator [1039:7018] (rev 02)
Subsystem: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator [1039:7018]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: Trident4DWaveAudio
00:01.6 Modem [0703]: Silicon Integrated Systems [SiS] AC'97 Modem Controller [1039:7013] (rev a0) (prog-if 00 [Generic])
Subsystem: ASUSTeK Computer Inc. Device [1043:1457]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (13000ns min, 2750ns max)
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at b800 [size=256]
Region 1: I/O ports at b400 [size=128]
Capabilities: <access denied>
Kernel driver in use: Intel ICH Modem
00:02.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] AGP Port (virtual PCI-to-PCI bridge) [1039:0001] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d1800000-d1ffffff
Prefetchable memory behind bridge: d8000000-e7efffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:0a.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev 80)
Subsystem: ASUSTeK Computer Inc. Device [1043:1504]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 28020000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 18000000-1bfff000 (prefetchable)
Memory window 1: 1c000000-1ffff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
00:0a.1 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev 80)
Subsystem: ASUSTeK Computer Inc. Device [1043:1504]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin B routed to IRQ 5
Region 0: Memory at 28021000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 24000000-27fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter [1039:6300] (rev 31) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:1452]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
BIST result: 00
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d1800000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at a800 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
** USB devices:
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.1.0-1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.41
ii initramfs-tools [linux-initramfs-tool] 0.99
ii linux-base 3.4
ii module-init-tools 3.16-1
Versions of packages linux-image-3.1.0-1-686-pae recommends:
ii firmware-linux-free 3
ii libc6-i686 2.13-21
Versions of packages linux-image-3.1.0-1-686-pae suggests:
pn grub-pc 1.99-14
pn linux-doc-3.1 <none>
Versions of packages linux-image-3.1.0-1-686-pae is related to:
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.1.0-1-686-pae/prerm/removing-running-kernel-3.1.0-1-686-pae: true
linux-image-3.1.0-1-686-pae/postinst/missing-firmware-3.1.0-1-686-pae:
linux-image-3.1.0-1-686-pae/postinst/ignoring-ramdisk:
linux-image-3.1.0-1-686-pae/postinst/depmod-error-initrd-3.1.0-1-686-pae: false
Reply to: