Bug#653192: linux 3.2~rc4-1~experimental.1: Intel X-25M SSD destroyed
Package: src:linux-2.6
Version: 3.2~rc4-1~experimental.1
Severity: critical
Justification: causes serious data loss
Hi,
My system has run Debian 2.6.32 kernels for 21 months, with two RAID-1s
spanning a pair of Intel X-25M 80GiB SSDs; one RAID (sd[ab]1) is for a
/boot filesystem, and another (sd[ab]2) contains an encrypted LVM with
everything else, all reiserfs filesystems. There was also an
unformatted partition sda3 and an ntfs partition sdb3.
Today I tried booting 3.2~rc4-1~experimental.1, which seemed fine until
after a few minutes various programs in a graphical desktop environment
started to hang, apparently when trying to load anything from disk that
was not already in cache.
Ctrl+Alt+F1-6 wasn't working. After a SysRq-S,U,B forced reboot, one of
my SSDs (sdb) now seems to be toast. I'm only able to read the first
16KiB of data from it, which still contains the original intact
partition table and embedded GRUB. The rest is neither readable nor
writable, with these errors:
> [ 749.427493] end_request: I/O error, dev sdb, sector 32
> [ 749.427501] __ratelimit: 2619 callbacks suppressed
> [ 749.427508] Buffer I/O error on device sdb, logical block 4
> [ 757.362967] sd 4:0:0:0: [sdb] Unhandled error code
> [ 757.362979] sd 4:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
printk is flooded on startup with many other errors that I'm unable to
retrieve from dmesg, for about 5 minutes until the system eventually
boots 2.6.32 from the degraded RAID using the other apparently intact
SSD. Other errors I noticed include:
* sector reallocation failures
* nv SATA controller resetting the port
I don't imagine my bug report is of much help fixing the issue, but I at
least wanted to warn anyone before trying it. I don't exactly have a
shelf full of spare ~£120 SSDs for further testing/debugging. In the
meantime I'll see if I can somehow fix the 'broken' SSD.
I would have suspected that this was an underlying drive firmware bug,
triggered by linux-3.2 or 3.0 implementing the SSD TRIM/discard feature,
but actually I don't think that feature is enabled in the 02G9 firmware
of these drives, and also I doubt reiserfs would make use of those
features, especially on top of encrypted LVM.
I'd previously tested 3.0 kernels from unstable but given up on them due
to similar hangs on disk reads, possibly related to reiserfs. I didn't
suffer any loss of data or destruction of hardware until now though.
I'd rebuilt 3.2.0-rc4-rt-amd64 with the custom DSDT I normally use on
2.6.32 to enable powernow-k8, and since this is an RT-patched kernel
flavour I'd exported some GPL-only symbols to be able to build the
nvidia module with DKMS.
Kernel log leading up to the crash:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-rc4-rt-amd64 (Debian
3.2~rc4-1~experimental.1+dsdt1) (steven@pyro.eu.org) (gcc version 4.4.5
(Debian 4.4.5-8) ) #1 SMP PREEMPT RT Sat Dec 24 18:42:30 GMT 2011
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.2.0-rc4-rt-amd64
root=/dev/mapper/acidbath-root ro single clocksource=acpi_pm
iommu=memaper=1 threadirqs
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009d400 (usable)
[ 0.000000] BIOS-e820: 000000000009d400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fff9300 (usable)
[ 0.000000] BIOS-e820: 000000007fff9300 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000180000000 (usable)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.3 present.
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x180000 max_arch_pfn = 0x400000000
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
0x7010600070106
[ 0.000000] last_pfn = 0x7fff9 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [ffff8800000f9bf0] f9bf0
[ 0.000000] init_memory_mapping: 0000000000000000-000000007fff9000
[ 0.000000] init_memory_mapping: 0000000100000000-0000000180000000
[ 0.000000] RAMDISK: 37431000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000e8010 00024 (v02 HP )
[ 0.000000] ACPI: XSDT 000000007fff94fc 0003C (v01 HP CPQ0062
20061128 00000000)
[ 0.000000] ACPI: FACP 000000007fff96a4 0010C (v03 HP VIPER
00000001 00000000)
[ 0.000000] ACPI Warning: FADT (revision 3) is longer than ACPI 2.0
version, truncating length 268 to 244 (20110623/tbfadt-288)
[ 0.000000] ACPI: Override [DSDT- DSDT], this is unsafe: tainting
kernel
[ 0.000000] Disabling lock debugging due to kernel taint
[ 0.000000] ACPI: DSDT @ 0x000000007fff989a Table override, replaced
with:
[ 0.000000] ACPI: DSDT ffffffff8164c890 04BF8 (v01 HP DSDT
00000001 INTL 20100528)
[ 0.000000] ACPI: FACS 000000007fff9300 00040
[ 0.000000] ACPI: SSDT 000000007fffad49 03C2B (v02 HP PROJECT
00000001 MSFT 0100000E)
[ 0.000000] ACPI: APIC 000000007fff97b0 0009E (v01 HP VIPER
00000001 00000000)
[ 0.000000] Scanning NUMA topology in Northbridge 24
[ 0.000000] Number of physical nodes 2
[ 0.000000] Node 0 using interleaving mode 1/1
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000180000000
[ 0.000000] Initmem setup node 0 0000000000000000-0000000180000000
[ 0.000000] NODE_DATA [000000017fffb000 - 000000017fffffff]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00180000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009d
[ 0.000000] 0: 0x00000100 -> 0x0007fff9
[ 0.000000] 0: 0x00100000 -> 0x00180000
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0xf808
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 17, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: IOAPIC (id[0x09] address[0xf3500000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 9, version 17, address 0xf3500000, GSI
24-27
[ 0.000000] ACPI: IOAPIC (id[0x0a] address[0xf3501000] gsi_base[28])
[ 0.000000] IOAPIC[2]: apic_id 10, version 17, address 0xf3501000,
GSI 28-31
[ 0.000000] ACPI: IOAPIC (id[0x0b] address[0xf3000000] gsi_base[32])
[ 0.000000] IOAPIC[3]: apic_id 11, version 17, address 0xf3000000,
GSI 32-55
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: 000000000009d000 -
000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000e8000
[ 0.000000] PM: Registered nosave memory: 00000000000e8000 -
0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000007fff9000 -
000000007fffa000
[ 0.000000] PM: Registered nosave memory: 000000007fffa000 -
0000000080000000
[ 0.000000] PM: Registered nosave memory: 0000000080000000 -
00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 -
0000000100000000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap:
80000000:7ec00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512
nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 106 pages/cpu @ffff88017fc00000 s403712
r8192 d22272 u524288
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 1026945
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line:
BOOT_IMAGE=/vmlinuz-3.2.0-rc4-rt-amd64 root=/dev/mapper/acidbath-root ro
single clocksource=acpi_pm iommu=memaper=1 threadirqs
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Checking aperture...
[ 0.000000] Node 0: aperture @ 5e40000000 size 32 MB
[ 0.000000] Aperture beyond 4GB. Ignoring.
[ 0.000000] Your BIOS doesn't leave a aperture memory hole
[ 0.000000] Please enable the IOMMU option in the BIOS setup
[ 0.000000] This costs you 64 MB of RAM
[ 0.000000] Mapping aperture over 65536 KB of RAM @ 74000000
[ 0.000000] PM: Registered nosave memory: 0000000074000000 -
0000000078000000
[ 0.000000] Memory: 3981732k/6291456k available (3494k kernel code,
2097640k absent, 212084k reserved, 3284k data, 908k init)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:33024 nr_irqs:1024 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2593.037 MHz processor.
[ 0.000000] Marking TSC unstable due to TSCs unsynchronized
[ 0.004006] Calibrating delay loop (skipped), value calculated using
timer frequency.. 5186.07 BogoMIPS (lpj=10372148)
[ 0.004010] pid_max: default: 32768 minimum: 301
[ 0.004078] Security Framework initialized
[ 0.004496] Dentry cache hash table entries: 524288 (order: 10,
4194304 bytes)
[ 0.008389] Inode-cache hash table entries: 262144 (order: 9, 2097152
bytes)
[ 0.009815] Mount-cache hash table entries: 256
[ 0.009996] Initializing cgroup subsys cpuacct
[ 0.010001] Initializing cgroup subsys memory
[ 0.010019] Initializing cgroup subsys devices
[ 0.010022] Initializing cgroup subsys freezer
[ 0.010024] Initializing cgroup subsys net_cls
[ 0.010026] Initializing cgroup subsys blkio
[ 0.010090] CPU: Physical Processor ID: 0
[ 0.010091] CPU: Processor Core ID: 0
[ 0.010093] mce: CPU supports 5 MCE banks
[ 0.010661] ACPI: Core revision 20110623
[ 0.013707] ACPI Error: [VECT] Namespace lookup failure,
AE_ALREADY_EXISTS (20110623/dswload-337)
[ 0.013713] ACPI Exception: AE_ALREADY_EXISTS, During name
lookup/catalog (20110623/psloop-231)
[ 0.020387] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 0.060081] CPU0: Dual Core AMD Opteron(tm) Processor 285 stepping 02
[ 0.064003] Performance Events: AMD PMU driver.
[ 0.064003] ... version: 0
[ 0.064003] ... bit width: 48
[ 0.064003] ... generic registers: 4
[ 0.064003] ... value mask: 0000ffffffffffff
[ 0.064003] ... max period: 00007fffffffffff
[ 0.064003] ... fixed-purpose events: 0
[ 0.064003] ... event mask: 000000000000000f
[ 0.076124] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.096033] Booting Node 0, Processors #1
[ 0.184126] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.200047] #2
[ 0.288228] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.304051] #3 Ok.
[ 0.392159] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.396032] Brought up 4 CPUs
[ 0.396035] Total of 4 processors activated (20745.82 BogoMIPS).
[ 0.396761] devtmpfs: initialized
[ 0.403355] print_constraints: dummy:
[ 0.403355] NET: Registered protocol family 16
[ 0.404075] TOM: 0000000080000000 aka 2048M
[ 0.404093] TOM2: 0000000180000000 aka 6144M
[ 0.404141] ACPI: bus type pci registered
[ 0.404265] PCI: Using configuration type 1 for base access
[ 0.405421] bio: create slab <bio-0> at 0
[ 0.405421] ACPI: Added _OSI(Module Device)
[ 0.405421] ACPI: Added _OSI(Processor Device)
[ 0.405421] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.405421] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.415413] ACPI: Interpreter enabled
[ 0.415418] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.415469] ACPI: Using IOAPIC for interrupt routing
[ 0.425644] ACPI: No dock devices found.
[ 0.425646] HEST: Table not found.
[ 0.425649] PCI: Ignoring host bridge windows from ACPI; if
necessary, use "pci=use_crs" and report a bug
[ 0.427408] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3f])
[ 0.431088] HPET not enabled in BIOS. You might try hpet=force boot
option
[ 0.431874] pci 0000:00:09.0: PCI bridge to [bus 05-05] (subtractive
decode)
[ 0.431924] pci 0000:00:0e.0: PCI bridge to [bus 0a-0a]
[ 0.432397] pci0000:00: Unable to request _OSC control (_OSC support
mask: 0x1e)
[ 0.451260] ACPI: PCI Root Bridge [PCI1] (domain 0000 [bus 40-7f])
[ 0.455015] pci 0000:40:01.0: PCI bridge to [bus 41-41]
[ 0.455210] pci 0000:40:02.0: PCI bridge to [bus 61-61]
[ 0.455845] pci0000:40: Unable to request _OSC control (_OSC support
mask: 0x1e)
[ 0.459086] ACPI: PCI Root Bridge [PCI2] (domain 0000 [bus 80-ff])
[ 0.468049] pci 0000:80:0e.0: PCI bridge to [bus 81-81]
[ 0.468297] pci0000:80: Unable to request _OSC control (_OSC support
mask: 0x1e)
[ 0.469343] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *11
[ 0.469659] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0,
disabled.
[ 0.469973] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *5
[ 0.470287] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *10
[ 0.470368] ACPI: PCI Interrupt Link [LNKW] (IRQs *48), disabled.
[ 0.470448] ACPI: PCI Interrupt Link [LNKX] (IRQs *49), disabled.
[ 0.470527] ACPI: PCI Interrupt Link [LNKY] (IRQs *50), disabled.
[ 0.470606] ACPI: PCI Interrupt Link [LNKZ] (IRQs *51), disabled.
[ 0.470923] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *5
[ 0.471238] ACPI: PCI Interrupt Link [LSB0] (IRQs 20 21 22 23) *10
[ 0.471552] ACPI: PCI Interrupt Link [LSB2] (IRQs 20 21 22 23) *11
[ 0.471867] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *5
[ 0.472200] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22 23) *5
[ 0.472516] ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22 23) *0,
disabled.
[ 0.472831] ACPI: PCI Interrupt Link [LIDE] (IRQs 20 21 22 23) *0,
disabled.
[ 0.473155] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *10
[ 0.473480] ACPI: PCI Interrupt Link [LSA1] (IRQs 20 21 22 23) *11
[ 0.473649] vgaarb: device added:
PCI:0000:81:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.473649] vgaarb: loaded
[ 0.473649] vgaarb: bridge control possible 0000:81:00.0
[ 0.473649] PCI: Using ACPI for IRQ routing
[ 0.480609] pnp: PnP ACPI init
[ 0.480643] ACPI: bus type pnp registered
[ 0.484836] system 00:0a: [io 0x04d0-0x04d1] has been reserved
[ 0.485022] system 00:0b: [io 0x0400-0x047f] has been reserved
[ 0.485025] system 00:0b: [io 0x0480-0x048f] has been reserved
[ 0.485029] system 00:0b: [io 0xf800-0xf87f] has been reserved
[ 0.485032] system 00:0b: [io 0xf880-0xf8ff] has been reserved
[ 0.485035] system 00:0b: [io 0xf900-0xf97f] has been reserved
[ 0.485039] system 00:0b: [io 0xf980-0xf9ff] has been reserved
[ 0.485044] system 00:0b: [io 0xfa00-0xfa7f] has been reserved
[ 0.485047] system 00:0b: [io 0xfa80-0xfaff] has been reserved
[ 0.485051] system 00:0b: [io 0xfc00-0xfc7f] has been reserved
[ 0.485054] system 00:0b: [io 0xfc80-0xfcff] has been reserved
[ 0.485058] system 00:0b: [io 0xfe00-0xfe7f] has been reserved
[ 0.485061] system 00:0b: [io 0xfe80-0xfeff] has been reserved
[ 0.512063] pnp 00:0e: disabling [mem 0x00000000-0x0009ffff] because
it overlaps 0000:61:06.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.512063] pnp 00:0e: disabling [mem 0x000e8000-0x000fffff] because
it overlaps 0000:61:06.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.512063] pnp 00:0e: disabling [mem 0x000d5200-0x000dffff] because
it overlaps 0000:61:06.0 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.512063] pnp 00:0e: disabling [mem 0x00000000-0x0009ffff disabled]
because it overlaps 0000:61:06.1 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.512063] pnp 00:0e: disabling [mem 0x000e8000-0x000fffff disabled]
because it overlaps 0000:61:06.1 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.512067] pnp 00:0e: disabling [mem 0x000d5200-0x000dffff disabled]
because it overlaps 0000:61:06.1 BAR 6 [mem 0x00000000-0x000fffff pref]
[ 0.512156] system 00:0e: [mem 0x00100000-0x7fffffff] could not be
reserved
[ 0.512160] system 00:0e: [mem 0xfec01000-0xffffffff] has been reserved
[ 0.512177] pnp: PnP ACPI: found 15 devices
[ 0.512179] ACPI: ACPI bus type pnp unregistered
[ 0.521005] Switching to clocksource acpi_pm
[ 0.521137] pci 0000:00:09.0: PCI bridge to [bus 05-05]
[ 0.521140] pci 0000:00:09.0: bridge window [io 0x3000-0x3fff]
[ 0.521143] pci 0000:00:09.0: bridge window [mem 0xf3600000-0xf36fffff]
[ 0.521147] pci 0000:00:0e.0: PCI bridge to [bus 0a-0a]
[ 0.521157] pci 0000:40:02.0: BAR 15: can't assign mem pref (size
0x200000)
[ 0.521161] pci 0000:40:01.0: PCI bridge to [bus 41-41]
[ 0.521169] pci 0000:61:06.0: BAR 6: can't assign mem pref (size
0x100000)
[ 0.521171] pci 0000:61:06.1: BAR 6: can't assign mem pref (size
0x100000)
[ 0.521175] pci 0000:40:02.0: PCI bridge to [bus 61-61]
[ 0.521177] pci 0000:40:02.0: bridge window [io 0x2000-0x2fff]
[ 0.521181] pci 0000:40:02.0: bridge window [mem 0xf3100000-0xf34fffff]
[ 0.521188] pci 0000:81:00.0: BAR 6: can't assign mem pref (size 0x20000)
[ 0.521191] pci 0000:80:0e.0: PCI bridge to [bus 81-81]
[ 0.521193] pci 0000:80:0e.0: bridge window [io 0x1000-0x1fff]
[ 0.521196] pci 0000:80:0e.0: bridge window [mem 0xf0000000-0xf2ffffff]
[ 0.521199] pci 0000:80:0e.0: bridge window [mem
0xd0000000-0xdfffffff 64bit pref]
[ 0.521412] NET: Registered protocol family 2
[ 0.521759] IP route cache hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.523867] TCP established hash table entries: 524288 (order: 11,
8388608 bytes)
[ 0.529854] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)
[ 0.532276] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.532279] TCP reno registered
[ 0.532347] UDP hash table entries: 2048 (order: 6, 262144 bytes)
[ 0.532564] UDP-Lite hash table entries: 2048 (order: 6, 262144 bytes)
[ 0.532943] NET: Registered protocol family 1
[ 0.588162] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.588167] pci 0000:00:0e.0: Found disabled HT MSI Mapping
[ 0.588173] pci 0000:00:00.0: Found enabled HT MSI Mapping
[ 0.588209] pci 0000:40:01.0: MSI quirk detected; subordinate MSI
disabled
[ 0.588212] pci 0000:40:01.0: AMD8131 rev 12 detected; disabling
PCI-X MMRBC
[ 0.588219] pci 0000:40:02.0: MSI quirk detected; subordinate MSI
disabled
[ 0.588222] pci 0000:40:02.0: AMD8131 rev 12 detected; disabling
PCI-X MMRBC
[ 0.588288] pci 0000:80:00.0: Found disabled HT MSI Mapping
[ 0.588293] pci 0000:80:0e.0: Enabling HT MSI Mapping
[ 0.588300] pci 0000:80:0e.0: Found enabled HT MSI Mapping
[ 0.588424] Unpacking initramfs...
[ 0.901284] Freeing initrd memory: 12028k freed
[ 0.913040] PCI-DMA: Disabling AGP.
[ 0.913183] PCI-DMA: aperture base @ 74000000 size 65536 KB
[ 0.913184] PCI-DMA: using GART IOMMU.
[ 0.913189] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 0.924793] audit: initializing netlink socket (disabled)
[ 0.924818] type=2000 audit(1324756913.920:1): initialized
[ 0.952964] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.953433] VFS: Disk quotas dquot_6.5.2
[ 0.953500] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.953648] msgmni has been set to 7929
[ 0.953989] alg: No test for stdrng (krng)
[ 0.954046] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.954049] io scheduler noop registered
[ 0.954051] io scheduler deadline registered
[ 0.954085] io scheduler cfq registered (default)
[ 0.967645] ERST: Table is not found!
[ 0.967647] GHES: HEST is not enabled!
[ 0.967753] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.988100] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.216477] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.260341] Linux agpgart interface v0.103
[ 1.260572] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at
0x60,0x64 irq 1,12
[ 1.263163] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.263191] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.263509] mousedev: PS/2 mouse device common for all mice
[ 1.263577] rtc_cmos 00:03: RTC can wake from S4
[ 1.263754] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.263831] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 1.263855] cpuidle: using governor ladder
[ 1.263857] cpuidle: using governor menu
[ 1.264380] TCP cubic registered
[ 1.264464] NET: Registered protocol family 10
[ 1.265608] Mobile IPv6
[ 1.265611] NET: Registered protocol family 17
[ 1.265617] Registering the dns_resolver key type
[ 1.265896] registered taskstats version 1
[ 1.266526] rtc_cmos 00:03: setting system clock to 2011-12-24
20:01:54 UTC (1324756914)
[ 1.266607] Initializing network drop monitor service
[ 1.269567] Freeing unused kernel memory: 908k freed
[ 1.270155] Write protecting the kernel read-only data: 6144k
[ 1.272806] Freeing unused kernel memory: 584k freed
[ 1.276500] Freeing unused kernel memory: 740k freed
[ 1.283629] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 1.308112] udev[99]: starting version 164
[ 1.449041] SCSI subsystem initialized
[ 1.450488] forcedeth: Reverse Engineered nForce ethernet driver.
Version 0.64.
[ 1.451095] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 23
[ 1.451115] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 23
(level, high) -> IRQ 23
[ 1.453280] usbcore: registered new interface driver usbfs
[ 1.453818] usbcore: registered new interface driver hub
[ 1.454379] usbcore: registered new device driver usb
[ 1.455689] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 19
[ 1.455703] firewire_ohci 0000:05:05.0: PCI INT A -> Link[LNKD] ->
GSI 19 (level, high) -> IRQ 19
[ 1.458832] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.462036] FDC 0 is a post-1991 82077
[ 1.508181] firewire_ohci: Added fw-ohci device 0000:05:05.0, OHCI
v1.10, 4 IR + 8 IT contexts, quirks 0x2
[ 1.545709] Fusion MPT base driver 3.04.20
[ 1.545712] Copyright (c) 1999-2008 LSI Corporation
[ 1.546690] Fusion MPT SPI Host driver 3.04.20
[ 1.546843] mptspi 0000:61:06.0: PCI INT A -> GSI 30 (level, low) ->
IRQ 30
[ 1.547199] mptbase: ioc0: Initiating bringup
[ 1.972834] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x5043 @ 1,
addr 00:16:35:37:90:7f
[ 1.972837] forcedeth 0000:00:0a.0: highdma csum gbit lnktim desc-v3
[ 1.973281] ACPI: PCI Interrupt Link [LSB2] enabled at IRQ 22
[ 1.973296] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LSB2] -> GSI 22
(level, high) -> IRQ 22
[ 1.973330] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 1.973368] ehci_hcd 0000:00:02.1: new USB bus registered, assigned
bus number 1
[ 1.973403] ehci_hcd 0000:00:02.1: debug port 1
[ 1.973482] ehci_hcd 0000:00:02.1: irq 22, io mem 0xfebf0000
[ 1.984056] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 1.984118] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.984121] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.984123] usb usb1: Product: EHCI Host Controller
[ 1.984124] usb usb1: Manufacturer: Linux 3.2.0-rc4-rt-amd64 ehci_hcd
[ 1.984126] usb usb1: SerialNumber: 0000:00:02.1
[ 1.984319] hub 1-0:1.0: USB hub found
[ 1.984327] hub 1-0:1.0: 10 ports detected
[ 1.985294] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.985751] scsi0 : pata_amd
[ 1.985925] scsi1 : pata_amd
[ 1.986217] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x48a0
irq 14
[ 1.986220] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x48a8
irq 15
[ 1.990619] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 21
[ 1.990635] sata_nv 0000:00:07.0: PCI INT A -> Link[LSA0] -> GSI 21
(level, high) -> IRQ 21
[ 1.991130] scsi2 : sata_nv
[ 1.991246] scsi3 : sata_nv
[ 1.991331] ata3: SATA max UDMA/133 cmd 0x48d0 ctl 0x48f8 bmdma
0x48b0 irq 21
[ 1.991333] ata4: SATA max UDMA/133 cmd 0x48d8 ctl 0x48fc bmdma
0x48b8 irq 21
[ 1.991711] ACPI: PCI Interrupt Link [LSB0] enabled at IRQ 20
[ 1.991722] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LSB0] -> GSI 20
(level, high) -> IRQ 20
[ 1.991736] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 1.991756] ohci_hcd 0000:00:02.0: new USB bus registered, assigned
bus number 2
[ 1.991844] ohci_hcd 0000:00:02.0: irq 20, io mem 0xf3700000
[ 2.008165] firewire_core: created device fw0: GUID 0060b0000018577d,
S400
[ 2.016059] ioc0: LSI53C1030 B2: Capabilities={Initiator,Target}
[ 2.046067] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.046069] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 2.046071] usb usb2: Product: OHCI Host Controller
[ 2.046073] usb usb2: Manufacturer: Linux 3.2.0-rc4-rt-amd64 ohci_hcd
[ 2.046075] usb usb2: SerialNumber: 0000:00:02.0
[ 2.046287] hub 2-0:1.0: USB hub found
[ 2.046295] hub 2-0:1.0: 10 ports detected
[ 2.046894] ACPI: PCI Interrupt Link [LSA1] enabled at IRQ 23
[ 2.046899] sata_nv 0000:00:08.0: PCI INT A -> Link[LSA1] -> GSI 23
(level, high) -> IRQ 23
[ 2.047446] scsi4 : sata_nv
[ 2.047581] scsi5 : sata_nv
[ 2.047666] ata5: SATA max UDMA/133 cmd 0x48e0 ctl 0x4c00 bmdma
0x48c0 irq 23
[ 2.047669] ata6: SATA max UDMA/133 cmd 0x48e8 ctl 0x4c04 bmdma
0x48c8 irq 23
[ 2.156360] ata1.00: ATAPI: HL-DT-STDVD-RAM GSA-H55N, 1.02, max UDMA/66
[ 2.156366] ata1.01: ATAPI: HL-DT-STDVD-RAM GSA-H55N, 1.02, max UDMA/66
[ 2.172293] ata1.00: configured for UDMA/66
[ 2.188290] ata1.01: configured for UDMA/44
[ 2.192090] scsi 0:0:0:0: CD-ROM HL-DT-ST DVD-RAM GSA-H55N
1.02 PQ: 0 ANSI: 5
[ 2.193836] scsi 0:0:1:0: CD-ROM HL-DT-ST DVD-RAM GSA-H55N
1.02 PQ: 0 ANSI: 5
[ 2.300031] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.450783] scsi6 : ioc0: LSI53C1030 B2, FwRev=01032700h, Ports=1,
MaxQ=255, IRQ=30
[ 2.512064] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.520237] ata5.00: ATA-7: INTEL SSDSA2M080G2GC, 2CV102G9, max UDMA/133
[ 2.520240] ata5.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 2.528231] ata5.00: configured for UDMA/133
[ 2.544064] usb 2-4: new low-speed USB device number 2 using ohci_hcd
[ 2.668051] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.668187] scsi 4:0:0:0: Direct-Access ATA INTEL SSDSA2M080
2CV1 PQ: 0 ANSI: 5
[ 2.759079] usb 2-4: New USB device found, idVendor=046d, idProduct=c046
[ 2.759081] usb 2-4: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 2.759083] usb 2-4: Product: USB Optical Mouse
[ 2.759085] usb 2-4: Manufacturer: Logitech
[ 3.085446] mptspi 0000:61:06.1: PCI INT B -> GSI 31 (level, low) ->
IRQ 31
[ 3.085682] mptbase: ioc1: Initiating bringup
[ 3.136038] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.144208] ata6.00: ATA-7: INTEL SSDSA2M080G2GC, 2CV102G9, max UDMA/133
[ 3.144210] ata6.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 3.152227] ata6.00: configured for UDMA/133
[ 3.152247] scsi: waiting for bus probes to complete ...
[ 3.548025] ioc1: LSI53C1030 B2: Capabilities={Initiator,Target}
[ 4.022837] scsi7 : ioc1: LSI53C1030 B2, FwRev=01032700h, Ports=1,
MaxQ=255, IRQ=31
[ 8.163406] scsi 5:0:0:0: Direct-Access ATA INTEL SSDSA2M080
2CV1 PQ: 0 ANSI: 5
[ 8.194673] sd 4:0:0:0: [sda] 156301488 512-byte logical blocks:
(80.0 GB/74.5 GiB)
[ 8.194760] sd 4:0:0:0: [sda] Write Protect is off
[ 8.194799] sd 4:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 8.195948] sd 5:0:0:0: [sdb] 156301488 512-byte logical blocks:
(80.0 GB/74.5 GiB)
[ 8.196064] sd 5:0:0:0: [sdb] Write Protect is off
[ 8.196102] sd 5:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 8.197994] sda: sda1 sda2 sda3
[ 8.198159] sdb: sdb1 sdb2 sdb3
[ 8.198786] sd 4:0:0:0: [sda] Attached SCSI disk
[ 8.199321] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 8.200278] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 8.200283] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 8.214344] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 8.214692] input: Logitech USB Optical Mouse as
/devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/input/input1
[ 8.215420] generic-usb 0003:046D:C046.0001: input,hidraw0: USB HID
v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:02.0-4/input0
[ 8.215489] usbcore: registered new interface driver usbhid
[ 8.215491] usbhid: USB HID core driver
[ 8.229660] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 8.229790] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 8.229933] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 8.230396] sd 5:0:0:0: Attached scsi generic sg3 type 0
[ 8.440297] md: raid1 personality registered for level 1
[ 8.451724] md: md1 stopped.
[ 8.454259] md: bind<sda2>
[ 8.454588] md: bind<sdb2>
[ 8.457646] bio: create slab <bio-1> at 1
[ 8.457892] md/raid1:md1: active with 2 out of 2 mirrors
[ 8.457933] md1: detected capacity change from 0 to 39739916288
[ 8.460094] md1: unknown partition table
[ 8.464618] device-mapper: uevent: version 1.0.3
[ 8.464765] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19)
initialised: dm-devel@redhat.com
[ 34.626365] Intel AES-NI instructions are not detected.
[ 34.966167] REISERFS (device dm-1): found reiserfs format "3.6" with
non-standard journal
[ 34.966179] REISERFS (device dm-1): using ordered data mode
[ 34.966180] reiserfs: using flush barriers
[ 34.966678] REISERFS (device dm-1): journal params: device dm-1, size
8172, journal first block 18, max trans len 1024, max batch 900, max
commit age 30, max trans age 30
[ 34.967916] REISERFS (device dm-1): checking transaction log (dm-1)
[ 34.973439] REISERFS (device dm-1): Using r5 hash to sort names
[ 35.240304] udev[577]: starting version 164
[ 35.629119] MCE: In-kernel MCE decoding enabled.
[ 35.635913] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 35.645723] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 35.646083] EDAC MC: Ver: 2.1.0
[ 35.647739] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 35.654155] ACPI: Power Button [PBTN]
[ 35.659629] AMD64 EDAC driver v3.4.0
[ 35.666237] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 35.667882] ACPI: Power Button [PWRF]
[ 35.669270] i2c i2c-0: nForce2 SMBus adapter at 0x4800
[ 35.695359] i2c i2c-1: nForce2 SMBus adapter at 0x4840
[ 35.696362] shpchp 0000:40:01.0: HPC vendor_id 1022 device_id 7450
ss_vid 0 ss_did 0
[ 35.696368] shpchp 0000:40:01.0: Cannot reserve MMIO region
[ 35.697664] shpchp 0000:40:02.0: HPC vendor_id 1022 device_id 7450
ss_vid 0 ss_did 0
[ 35.697667] shpchp 0000:40:02.0: Cannot reserve MMIO region
[ 35.700099] EDAC amd64: DRAM ECC enabled.
[ 35.700109] EDAC amd64: K8 revE or earlier detected (node 0).
[ 35.749796] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 35.750219] EDAC amd64: CS0: Registered Double data rate SDRAM
[ 35.750221] EDAC amd64: CS2: Registered Double data rate SDRAM
[ 35.770584] EDAC MC0: Giving out device to 'amd64_edac' 'K8': DEV
0000:00:18.2
[ 35.774867] EDAC amd64: DRAM ECC enabled.
[ 35.774879] EDAC amd64: K8 revE or earlier detected (node 1).
[ 35.774964] EDAC amd64: CS2: Registered Double data rate SDRAM
[ 35.774995] EDAC MC1: Giving out device to 'amd64_edac' 'K8': DEV
0000:00:19.2
[ 35.775354] EDAC PCI0: Giving out device to module 'amd64_edac'
controller 'EDAC PCI controller': DEV '0000:00:18.2' (POLLED)
[ 35.884482] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 18
[ 35.884508] snd_ice1712 0000:05:04.0: PCI INT A -> Link[LNKA] -> GSI
18 (level, high) -> IRQ 18
[ 35.957768] nvidia: module license 'NVIDIA' taints kernel.
[ 36.383992] input: PS/2 Logitech Mouse as
/devices/platform/i8042/serio1/input/input5
[ 37.710368] ACPI: PCI Interrupt Link [LNKY] enabled at IRQ 50
[ 37.710395] nvidia 0000:81:00.0: PCI INT A -> Link[LNKY] -> GSI 50
(level, high) -> IRQ 50
[ 37.710412] vgaarb: device changed decodes:
PCI:0000:81:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 37.710753] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 275.36
Sun Oct 16 21:53:01 PDT 2011
[ 37.752572] md: md0 stopped.
[ 37.755356] md: bind<sdb1>
[ 37.755710] md: bind<sda1>
[ 37.759857] md/raid1:md0: active with 2 out of 2 mirrors
[ 37.759910] md0: detected capacity change from 0 to 264175616
[ 37.768194] md0: unknown partition table
[ 37.859781] reiserfs: enabling write barrier flush mode
[ 37.913958] powernow-k8: Found 1 Dual Core AMD Opteron(tm) Processor
285 (4 cpu cores) (version 2.20.00)
[ 37.914129] powernow-k8: fid 0x12 (2600 MHz), vid 0x8
[ 37.914131] powernow-k8: fid 0x10 (2400 MHz), vid 0xa
[ 37.914132] powernow-k8: fid 0xe (2200 MHz), vid 0xc
[ 37.914134] powernow-k8: fid 0xc (2000 MHz), vid 0xe
[ 37.914136] powernow-k8: fid 0xa (1800 MHz), vid 0x10
[ 37.914137] powernow-k8: fid 0x2 (1000 MHz), vid 0x12
[ 37.914360] powernow-k8: fid 0x12 (2600 MHz), vid 0x8
[ 37.914362] powernow-k8: fid 0x10 (2400 MHz), vid 0xa
[ 37.914364] powernow-k8: fid 0xe (2200 MHz), vid 0xc
[ 37.914365] powernow-k8: fid 0xc (2000 MHz), vid 0xe
[ 37.914367] powernow-k8: fid 0xa (1800 MHz), vid 0x10
[ 37.914369] powernow-k8: fid 0x2 (1000 MHz), vid 0x12
[ 37.922543] smsc47b397: found SMSC LPC47B397-NC (base address 0x0480,
revision 1)
[ 38.068239] REISERFS (device dm-2): found reiserfs format "3.6" with
non-standard journal
[ 38.068262] REISERFS (device dm-2): using ordered data mode
[ 38.068264] reiserfs: using flush barriers
[ 38.068857] REISERFS (device dm-2): journal params: device dm-2, size
8172, journal first block 18, max trans len 1024, max batch 900, max
commit age 30, max trans age 30
[ 38.070387] REISERFS (device dm-2): checking transaction log (dm-2)
[ 38.074031] REISERFS (device dm-2): Using r5 hash to sort names
[ 38.076262] REISERFS (device dm-3): found reiserfs format "3.6" with
non-standard journal
[ 38.076285] REISERFS (device dm-3): using ordered data mode
[ 38.076286] reiserfs: using flush barriers
[ 38.076900] REISERFS (device dm-3): journal params: device dm-3, size
8172, journal first block 18, max trans len 1024, max batch 900, max
commit age 30, max trans age 30
[ 38.078520] REISERFS (device dm-3): checking transaction log (dm-3)
[ 38.081441] REISERFS (device dm-3): Using r5 hash to sort names
[ 38.083273] REISERFS (device dm-4): found reiserfs format "3.6" with
non-standard journal
[ 38.083308] REISERFS (device dm-4): using ordered data mode
[ 38.083309] reiserfs: using flush barriers
[ 38.083913] REISERFS (device dm-4): journal params: device dm-4, size
8172, journal first block 18, max trans len 1024, max batch 900, max
commit age 30, max trans age 30
[ 38.085527] REISERFS (device dm-4): checking transaction log (dm-4)
[ 38.088775] REISERFS (device dm-4): Using r5 hash to sort names
[ 38.090930] REISERFS (device dm-5): found reiserfs format "3.6" with
non-standard journal
[ 38.090966] REISERFS (device dm-5): using ordered data mode
[ 38.090968] reiserfs: using flush barriers
[ 38.091762] REISERFS (device dm-5): journal params: device dm-5, size
8172, journal first block 18, max trans len 1024, max batch 900, max
commit age 30, max trans age 30
[ 38.093418] REISERFS (device dm-5): checking transaction log (dm-5)
[ 38.096771] REISERFS (device dm-5): Using r5 hash to sort names
[ 38.098951] REISERFS (device dm-6): found reiserfs format "3.6" with
non-standard journal
[ 38.098989] REISERFS (device dm-6): using ordered data mode
[ 38.098991] reiserfs: using flush barriers
[ 38.099577] REISERFS (device dm-6): journal params: device dm-6, size
8172, journal first block 18, max trans len 1024, max batch 900, max
commit age 30, max trans age 30
[ 38.101196] REISERFS (device dm-6): checking transaction log (dm-6)
[ 38.104159] REISERFS (device dm-6): Using r5 hash to sort names
[ 38.142818] fuse init (API version 7.17)
[ 38.289384] REISERFS (device md0): found reiserfs format "3.6" with
non-standard journal
[ 38.289418] REISERFS (device md0): using ordered data mode
[ 38.289422] reiserfs: using flush barriers
[ 38.290107] REISERFS (device md0): journal params: device md0, size
8172, journal first block 18, max trans len 1024, max batch 900, max
commit age 30, max trans age 30
[ 38.292555] REISERFS (device md0): checking transaction log (md0)
[ 38.297117] REISERFS (device md0): Using r5 hash to sort names
[ 38.554140] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 38.592191] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 39.605617] 8021q: 802.1Q VLAN Support v1.8
[ 39.624229] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 44.106190] FS-Cache: Loaded
[ 44.126404] FS-Cache: Netfs 'cifs' registered for caching
[ 44.149731] CIFS VFS: Error connecting to socket. Aborting operation
[ 44.150011] CIFS VFS: cifs_mount failed w/return code = -111
[ 44.151137] CIFS VFS: default security mechanism requested. The
default security mechanism will be upgraded from ntlm to ntlmv2 in
kernel release 3.2
[ 44.390281] CIFS VFS: Error connecting to socket. Aborting operation
[ 44.390784] CIFS VFS: cifs_mount failed w/return code = -111
[ 44.411532] CIFS VFS: Error connecting to socket. Aborting operation
[ 44.411814] CIFS VFS: cifs_mount failed w/return code = -111
[ 44.426003] CIFS VFS: Error connecting to socket. Aborting operation
[ 44.426362] CIFS VFS: cifs_mount failed w/return code = -111
[ 44.440653] CIFS VFS: Error connecting to socket. Aborting operation
[ 44.440942] CIFS VFS: cifs_mount failed w/return code = -111
[ 44.455366] CIFS VFS: Error connecting to socket. Aborting operation
[ 44.455933] CIFS VFS: cifs_mount failed w/return code = -111
[ 44.595575] RPC: Registered named UNIX socket transport module.
[ 44.595581] RPC: Registered udp transport module.
[ 44.595586] RPC: Registered tcp transport module.
[ 44.595590] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 44.656333] FS-Cache: Netfs 'nfs' registered for caching
[ 44.680576] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 442.951038] CIFS VFS: Unexpected lookup error -512
[ 534.820170] vboxdrv: fAsync=1 offMin=0x117a669173 offMax=0x117a669173
[ 534.820351] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is
'normal'.
[ 534.848345] svc: failed to register lockdv1 RPC service (errno 97).
[ 534.848498] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state
recovery directory
[ 534.848538] NFSD: starting 90-second grace period
[ 534.860909] syslog-ng (1822): Attempt to access syslog with
CAP_SYS_ADMIN but no CAP_SYSLOG (deprecated).
[ 536.201619] Bluetooth: Core ver 2.16
[ 536.201890] NET: Registered protocol family 31
[ 536.201893] Bluetooth: HCI device and connection manager initialized
[ 536.201898] Bluetooth: HCI socket layer initialized
[ 536.201901] Bluetooth: L2CAP socket layer initialized
[ 536.201923] Bluetooth: SCO socket layer initialized
[ 536.215707] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 536.215711] Bluetooth: BNEP filters: protocol multicast
[ 536.227813] Bridge firewalling registered
[ 536.344356] Bluetooth: RFCOMM TTY layer initialized
[ 536.344378] Bluetooth: RFCOMM socket layer initialized
[ 536.344379] Bluetooth: RFCOMM ver 1.11
[ 536.392138] lp: driver loaded but no devices found
[ 536.412532] ppdev: user-space parallel port driver
[ 536.431203] sshd (2363): /proc/2363/oom_adj is deprecated, please use
/proc/2363/oom_score_adj instead.
[ 732.842261] i2c /dev entries driver
Regards,
--
Steven Chamberlain
steven@pyro.eu.org
Reply to: