Bug#649867: linux-image-3.1.0-1-686-pae: On boot, switch on too high video mode

To: Debian Bug Tracking System <submit@bugs.debian.org>
Subject: Bug#649867: linux-image-3.1.0-1-686-pae: On boot, switch on too high video mode
From: Stéphane Aulery <lkppo@free.fr>
Date: Thu, 24 Nov 2011 13:41:23 +0100
Message-id: <[🔎] 20111124124123.7759.53903.reportbug@isidore>
Reply-to: Stéphane Aulery <lkppo@free.fr>, 649867@bugs.debian.org
Package: linux-2.6

Version: 3.1.1-1
Justification: renders package unusable
Severity: grave

Dear Maintainer,

At present, I use a Kernel Linux 2.6.39-2-686-pae and I have just installed a
kernel Linux 3.1.0-1-686-pae.

Just after entering in runlevel S, kernel Linux 3.1.0-1-686-pae switch on too
high video mode for my old 1024x768 screen (Hyundai ImageQuest L50S), when It
configure video card. Kernel Linux 2.6.39-2-686-pae had always worked fine.

I have tried to force video mode at 1024x768x16 with GRUB_GFXMODE grub's
parameter. I take the same problem.

I suspect a problem with my poulsbo GMA500 Intel chipset.

Regards,


-- File /etc/default/grub

GRUB_DEFAULT=0
GRUB_TIMEOUT=5
GRUB_CMDLINE_LINUX_DEFAULT="quiet"
GRUB_GFXPAYLOAD_LINUX="keep"
GRUB_GFXMODE=1024x768x16


-- Package-specific info:
** Kernel log: boot messages should be attached

** Model information
not available

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation System Controller Hub (SCH Poulsbo) [8086:8100] (rev 07)
	Subsystem: Intel Corporation Device [8086:8119]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:02.0 VGA compatible controller [0300]: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller [8086:8108] (rev 07) (prog-if 00 [VGA controller])
	Subsystem: Intel Corporation Device [8086:8119]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at fe980000 (32-bit, non-prefetchable) [size=512K]
	Region 1: I/O ports at c880 [size=8]
	Region 2: Memory at d0000000 (32-bit, non-prefetchable) [size=256M]
	Region 3: Memory at fe940000 (32-bit, non-prefetchable) [size=256K]
	Expansion ROM at <unassigned> [disabled]
	Capabilities: <access denied>

00:1b.0 Audio device [0403]: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller [8086:811b] (rev 07)
	Subsystem: Intel Corporation Device [8086:8119]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at fe938000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: HDA Intel

00:1c.0 PCI bridge [0604]: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 [8086:8110] (rev 07) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fea00000-feafffff
	Prefetchable memory behind bridge: cff00000-cfffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1c.1 PCI bridge [0604]: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 2 [8086:8112] (rev 07) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: feb00000-febfffff
	Prefetchable memory behind bridge: 80000000-801fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport

00:1d.0 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 [8086:8114] (rev 07) (prog-if 00 [UHCI])
	Subsystem: Intel Corporation Device [8086:8119]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 4: I/O ports at c480 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.1 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 [8086:8115] (rev 07) (prog-if 00 [UHCI])
	Subsystem: Intel Corporation Device [8086:8119]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 17
	Region 4: I/O ports at c080 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.2 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 [8086:8116] (rev 07) (prog-if 00 [UHCI])
	Subsystem: Intel Corporation Device [8086:8119]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin C routed to IRQ 18
	Region 4: I/O ports at b880 [size=32]
	Kernel driver in use: uhci_hcd

00:1d.7 USB Controller [0c03]: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 [8086:8117] (rev 07) (prog-if 20 [EHCI])
	Subsystem: Intel Corporation Device [8086:8119]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin D routed to IRQ 19
	Region 0: Memory at fe937c00 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ehci_hcd

00:1f.0 ISA bridge [0601]: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge [8086:8119] (rev 07)
	Subsystem: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge [8086:8119]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel driver in use: lpc_sch

00:1f.1 IDE interface [0101]: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller [8086:811a] (rev 07) (prog-if 80 [Master])
	Subsystem: Intel Corporation Device [8086:8119]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
	Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
	Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
	Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
	Region 4: I/O ports at ffa0 [size=16]
	Kernel driver in use: pata_sch

01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
	Subsystem: Realtek Semiconductor Co., Ltd. TEG-ECTX Gigabit PCI-E Adapter [Trendnet] [10ec:8168]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 40
	Region 0: I/O ports at dd00 [size=256]
	Region 2: Memory at feaff000 (64-bit, non-prefetchable) [size=4K]
	Region 4: Memory at cfff0000 (64-bit, prefetchable) [size=64K]
	Expansion ROM at feac0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: r8169

02:00.0 Mass storage controller [0180]: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller [1095:3132] (rev 01)
	Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller [1095:3132]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at febffc00 (64-bit, non-prefetchable) [size=128]
	Region 2: Memory at febf8000 (64-bit, non-prefetchable) [size=16K]
	Region 4: I/O ports at e880 [size=128]
	Expansion ROM at feb00000 [disabled] [size=512K]
	Capabilities: <access denied>
	Kernel driver in use: sata_sil24


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter
Bus 002 Device 002: ID 058f:9254 Alcor Micro Corp. Hub
Bus 002 Device 003: ID 1e54:2030 TypeMatrix 2030 USB Keyboard
Bus 002 Device 004: ID 045e:0040 Microsoft Corp. Wheel Mouse Optical


-- System Information:
Debian Release: wheezy/sid
  APT prefers testing
  APT policy: (650, 'testing')
Architecture: i386 (i686)

Kernel: Linux 2.6.39-2-686-pae (SMP w/2 CPU cores)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-3.1.0-1-686-pae depends on:
ii  debconf [debconf-2.0]                   1.5.40
ii  initramfs-tools [linux-initramfs-tool]  0.99  
ii  linux-base                              3.3   
ii  module-init-tools                       3.16-1

Versions of packages linux-image-3.1.0-1-686-pae recommends:
ii  firmware-linux-free  3      
ii  libc6-i686           2.13-21

Versions of packages linux-image-3.1.0-1-686-pae suggests:
ii  grub-pc        1.99-14
ii  linux-doc-3.1  3.1.1-1

Versions of packages linux-image-3.1.0-1-686-pae is related to:
pn  firmware-bnx2           <none>
pn  firmware-bnx2x          <none>
pn  firmware-ipw2x00        <none>
pn  firmware-ivtv           <none>
pn  firmware-iwlwifi        <none>
pn  firmware-linux          <none>
pn  firmware-linux-nonfree  <none>
pn  firmware-qlogic         <none>
pn  firmware-ralink         0.34  
pn  xen-hypervisor          <none>

-- debconf information:
  linux-image-3.1.0-1-686-pae/prerm/removing-running-kernel-3.1.0-1-686-pae: true
  linux-image-3.1.0-1-686-pae/postinst/missing-firmware-3.1.0-1-686-pae:
  linux-image-3.1.0-1-686-pae/postinst/ignoring-ramdisk:
  linux-image-3.1.0-1-686-pae/postinst/depmod-error-initrd-3.1.0-1-686-pae: false
Reply to:
Follow-Ups:
- Bug#649867: [gma500] On boot, switches on too high video mode
  - From: Jonathan Nieder <jrnieder@gmail.com>
Prev by Date: Bug#583363: linux-image-2.6.32-3-686: Network hangs with network activity and date freezes
Next by Date: Re: b43 firmware ABI change
Previous by thread: Bug#649847: BUG at fs/btrfs/super.c:984 running df on seed Btrfs filesystem
Next by thread: Bug#649867: [gma500] On boot, switches on too high video mode
Index(es):
- Date
- Thread