Bug#649198: linux-image-2.6.32-5-amd64: Kernel Oops on try to use an USB CD drive that was powered off
Package: linux-2.6
Version: 2.6.32-35
Severity: normal
I experienced a kernel Oops at three occasions when i switched off
a USB CD drive while it was in use by an application.
It first happened with qemu (stress test), then with blkid (gnawing
on medium with LEC uncorrectable error), and now with my own application
(deliberately provoked).
I opened a file descriptor on /dev/sr2 by
$ xorriso -outdev /dev/sr2 -dialog on
waited for the dialog prompt and switched off the drive's power.
Logged by this line
[ 215.717297] usb 1-3: USB disconnect, address 5
Some seconds later i let xorriso attempt an ioctl(SG_IO) transaction,
by entering to the xorriso command prompt:
-toc
The reaction on the xorriso terminal is quite immediately:
Killed
Message from syslogd@debian2 at Nov 18 18:59:41 ...
kernel:[ 231.149073] Oops: 0011 [#1] SMP
and some of the lines which appear in the kernel log below.
(Not all. They appear randomly picked.)
The system seems still running well now.
The drive re-appeared as /dev/sr3 when i switched it on again.
/dev/sr2 does not exist any more.
The first power off
[ 137.749886] usb 1-3: USB disconnect, address 3
was made when no userspace application had a file descriptor open.
No Oops happened and the drive re-appeared under its old device file
address /dev/sr2.
(I have switched off USB drives on older Linux kernels in the past.
Including the one of Debian 5. There never happened an Oops. Sometimes
/dev/sr numbers were not re-used.)
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-35) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Tue Jun 14 09:42:28 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64 root=UUID=e3378181-54dc-4fe3-97e2-d7f2b6c1d296 ro quiet
** Tainted: D (128)
* Kernel has oopsed before.
** Kernel log:
[ 15.745638] Bluetooth: HCI socket layer initialized
[ 15.839019] Bluetooth: L2CAP ver 2.14
[ 15.839021] Bluetooth: L2CAP socket layer initialized
[ 15.854583] Bluetooth: RFCOMM TTY layer initialized
[ 15.854588] Bluetooth: RFCOMM socket layer initialized
[ 15.854590] Bluetooth: RFCOMM ver 1.11
[ 15.966296] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 15.966299] Bluetooth: BNEP filters: protocol multicast
[ 15.981540] Bridge firewalling registered
[ 16.446574] Bluetooth: SCO (Voice Link) ver 0.6
[ 16.446577] Bluetooth: SCO socket layer initialized
[ 17.026555] lp0: using parport0 (interrupt-driven).
[ 17.064563] ppdev: user-space parallel port driver
[ 20.402265] powernow-k8: Found 1 AMD Athlon(tm) II X4 620 Processor processors (4 cpu cores) (version 2.20.00)
[ 20.402310] powernow-k8: 0 : pstate 0 (2600 MHz)
[ 20.402311] powernow-k8: 1 : pstate 1 (1900 MHz)
[ 20.402313] powernow-k8: 2 : pstate 2 (1400 MHz)
[ 20.402314] powernow-k8: 3 : pstate 3 (800 MHz)
[ 20.640051] eth0: no IPv6 routers present
[ 137.749886] usb 1-3: USB disconnect, address 3
[ 160.256082] usb 1-3: new high speed USB device using ehci_hcd and address 5
[ 160.390473] usb 1-3: New USB device found, idVendor=152d, idProduct=2336
[ 160.390482] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 160.390489] usb 1-3: Product: JM20336 SATA, USB Combo
[ 160.390494] usb 1-3: Manufacturer: JMicron
[ 160.390498] usb 1-3: SerialNumber: 306663601043
[ 160.390699] usb 1-3: configuration #1 chosen from 1 choice
[ 160.391820] scsi9 : SCSI emulation for USB Mass Storage devices
[ 160.392007] usb-storage: device found at 5
[ 160.392011] usb-storage: waiting for device to settle before scanning
[ 165.392426] usb-storage: device scan complete
[ 165.397853] scsi 9:0:0:0: CD-ROM Optiarc BD RW BD-5300S 1.04 PQ: 0 ANSI: 0
[ 165.433854] sr2: scsi3-mmc drive: 5x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 165.434123] sr 9:0:0:0: Attached scsi CD-ROM sr2
[ 165.434266] sr 9:0:0:0: Attached scsi generic sg3 type 5
[ 215.717297] usb 1-3: USB disconnect, address 5
[ 231.149032] kernel tried to execute NX-protected page - exploit attempt? (uid: 1000)
[ 231.149041] BUG: unable to handle kernel paging request at ffffea0003fefb90
[ 231.149050] IP: [<ffffea0003fefb90>] 0xffffea0003fefb90
[ 231.149064] PGD 168c067 PUD 168d067 PMD 8000000004c001e3
[ 231.149073] Oops: 0011 [#1] SMP
[ 231.149080] last sysfs file: /sys/devices/pci0000:00/0000:00:12.2/class
[ 231.149087] CPU 3
[ 231.149091] Modules linked in: powernow_k8 cpufreq_powersave cpufreq_stats cpufreq_conservative cpufreq_userspace ppdev lp sco bridge stp bnep rfcomm l2cap crc16 bluetooth rfkill kvm_amd kvm binfmt_misc fuse loop snd_hda_codec_atihdmi snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq snd_timer snd_seq_device radeon ttm edac_core drm_kms_helper snd soundcore parport_pc snd_page_alloc edac_mce_amd drm parport k10temp i2c_algo_bit i2c_piix4 i2c_core shpchp pci_hotplug pcspkr evdev processor button ext3 jbd mbcache usbhid hid sg usb_storage sd_mod sr_mod crc_t10dif cdrom ata_generic ohci_hcd ahci r8169 ehci_hcd thermal mii pata_atiixp thermal_sys usbcore libata nls_base scsi_mod [last unloaded: scsi_wait_scan]
[ 231.149201] Pid: 2266, comm: xorriso Not tainted 2.6.32-5-amd64 #1 GA-MA74GM-S2H
[ 231.149207] RIP: 0010:[<ffffea0003fefb90>] [<ffffea0003fefb90>] 0xffffea0003fefb90
[ 231.149218] RSP: 0018:ffff88011f181be0 EFLAGS: 00010086
[ 231.149223] RAX: ffffea0003fefb90 RBX: ffff880125f7f0c0 RCX: 0000000000000010
[ 231.149229] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff880116578000
[ 231.149235] RBP: ffff880116578000 R08: 0000000000000000 R09: ffff880125f7f0c0
[ 231.149240] R10: 0000000000000000 R11: ffffea0003fefb90 R12: 0000000000000000
[ 231.149246] R13: 0000000000000000 R14: 0000000000000000 R15: ffff880125f7f0c0
[ 231.149253] FS: 00007fb0e663b700(0000) GS:ffff880005380000(0000) knlGS:0000000000000000
[ 231.149259] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 231.149264] CR2: ffffea0003fefb90 CR3: 0000000126bb8000 CR4: 00000000000006e0
[ 231.149270] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 231.149276] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 231.149282] Process xorriso (pid: 2266, threadinfo ffff88011f180000, task ffff88011f06dbd0)
[ 231.149287] Stack:
[ 231.149291] ffffffff8117f7f1 0000001000000041 0000000000000000 0000000000000101
[ 231.149299] <0> ffff88000000dd00 0000000000000041 ffff880125f7f0c0 ffff880116578000
[ 231.149308] <0> 0000000000000000 0000000000000000 0000000000000000 ffff880125f7f0c0
[ 231.149318] Call Trace:
[ 231.149331] [<ffffffff8117f7f1>] ? get_request+0x30/0x2ba
[ 231.149341] [<ffffffff8117fa9c>] ? get_request_wait+0x21/0x188
[ 231.149352] [<ffffffff810b9c48>] ? get_page_from_freelist+0x56b/0x760
[ 231.149375] [<ffffffffa0007274>] ? scsi_execute+0x3b/0x12f [scsi_mod]
[ 231.149395] [<ffffffffa00073a8>] ? scsi_execute_req+0x40/0xb9 [scsi_mod]
[ 231.149413] [<ffffffffa00073ef>] ? scsi_execute_req+0x87/0xb9 [scsi_mod]
[ 231.149432] [<ffffffffa0001d20>] ? ioctl_internal_command+0x64/0x16a [scsi_mod]
[ 231.149451] [<ffffffffa0001e80>] ? scsi_set_medium_removal+0x5a/0x98 [scsi_mod]
[ 231.149465] [<ffffffffa0068eae>] ? cdrom_release+0x18f/0x1fe [cdrom]
[ 231.149475] [<ffffffff810d51ae>] ? page_add_new_anon_rmap+0x58/0x78
[ 231.149486] [<ffffffff810ccb17>] ? handle_mm_fault+0x35c/0x80f
[ 231.149497] [<ffffffffa009a3d2>] ? sr_block_release+0x11/0x1d [sr_mod]
[ 231.149507] [<ffffffff811126a2>] ? __blkdev_put+0x94/0x14c
[ 231.149516] [<ffffffff810efc5d>] ? __fput+0x100/0x1af
[ 231.149524] [<ffffffff810ed0c2>] ? filp_close+0x5b/0x62
[ 231.149531] [<ffffffff810ed15d>] ? sys_close+0x94/0xcd
[ 231.149539] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 231.149544] Code: 00 15 00 20 2c 45 81 ff ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 10 00 00 00 ad de 00 02 20 00 00 00 ad de <00> 00 00 00 00 00 00 02 01 00 00 00 ff ff ff ff 02 00 02 00 00
[ 231.149607] RIP [<ffffea0003fefb90>] 0xffffea0003fefb90
[ 231.149616] RSP <ffff88011f181be0>
[ 231.149620] CR2: ffffea0003fefb90
[ 231.149626] ---[ end trace 6ae1ca446db37801 ]---
[ 582.544084] usb 1-3: new high speed USB device using ehci_hcd and address 6
[ 582.678026] usb 1-3: New USB device found, idVendor=152d, idProduct=2336
[ 582.678036] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 582.678043] usb 1-3: Product: JM20336 SATA, USB Combo
[ 582.678048] usb 1-3: Manufacturer: JMicron
[ 582.678052] usb 1-3: SerialNumber: 306663601043
[ 582.678257] usb 1-3: configuration #1 chosen from 1 choice
[ 582.679378] scsi10 : SCSI emulation for USB Mass Storage devices
[ 582.679564] usb-storage: device found at 6
[ 582.679573] usb-storage: waiting for device to settle before scanning
[ 587.676372] usb-storage: device scan complete
[ 587.680667] scsi 10:0:0:0: CD-ROM Optiarc BD RW BD-5300S 1.04 PQ: 0 ANSI: 0
[ 587.719166] sr3: scsi3-mmc drive: 5x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 587.719443] sr 10:0:0:0: Attached scsi CD-ROM sr3
[ 587.719591] sr 10:0:0:0: Attached scsi generic sg3 type 5
** Model information
sys_vendor: Gigabyte Technology Co., Ltd.
product_name: GA-MA74GM-S2H
product_version:
chassis_vendor: Gigabyte Technology Co., Ltd.
chassis_version:
bios_vendor: Award Software International, Inc.
bios_version: FD
board_vendor: Gigabyte Technology Co., Ltd.
board_name: GA-MA74GM-S2H
board_version: x.x
** Loaded modules:
Module Size Used by
powernow_k8 10978 0
cpufreq_powersave 902 0
cpufreq_stats 2659 0
cpufreq_conservative 5162 0
cpufreq_userspace 1992 0
ppdev 5030 0
lp 7462 0
sco 7225 2
bridge 39630 0
stp 1440 1 bridge
bnep 9427 2
rfcomm 29613 0
l2cap 24736 6 bnep,rfcomm
crc16 1319 1 l2cap
bluetooth 41827 6 sco,bnep,rfcomm,l2cap
rfkill 13044 3 bluetooth
kvm_amd 31862 0
kvm 214248 1 kvm_amd
binfmt_misc 6431 1
fuse 50892 1
loop 11799 0
snd_hda_codec_atihdmi 2251 1
snd_hda_codec_realtek 235602 1
snd_hda_intel 20035 1
snd_hda_codec 54244 3 snd_hda_codec_atihdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 5380 1 snd_hda_codec
snd_pcm 60503 2 snd_hda_intel,snd_hda_codec
snd_seq 42881 0
snd_timer 15582 2 snd_pcm,snd_seq
snd_seq_device 4493 1 snd_seq
radeon 574844 2
ttm 40146 1 radeon
edac_core 29261 0
drm_kms_helper 20369 1 radeon
snd 46526 10 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 4598 1 snd
parport_pc 18855 1
snd_page_alloc 6249 2 snd_hda_intel,snd_pcm
edac_mce_amd 6433 0
drm 142327 4 radeon,ttm,drm_kms_helper
parport 27954 3 ppdev,lp,parport_pc
k10temp 2715 0
i2c_algo_bit 4225 1 radeon
i2c_piix4 8328 0
i2c_core 15819 5 radeon,drm_kms_helper,drm,i2c_algo_bit,i2c_piix4
shpchp 26264 0
pci_hotplug 21203 1 shpchp
pcspkr 1699 0
evdev 7352 8
processor 29935 1 powernow_k8
button 4650 0
ext3 106630 1
jbd 37085 1 ext3
mbcache 5050 1 ext3
usbhid 33292 2
hid 63257 1 usbhid
sg 24069 0
usb_storage 39961 1
sd_mod 29921 3
sr_mod 12602 1
crc_t10dif 1276 1 sd_mod
cdrom 29415 1 sr_mod
ata_generic 3239 0
ohci_hcd 19343 0
ahci 32534 2
r8169 29279 0
ehci_hcd 32081 0
thermal 11674 0
mii 3210 1 r8169
pata_atiixp 3489 0
thermal_sys 11942 2 processor,thermal
usbcore 122498 7 usbhid,usb_storage,ohci_hcd,ehci_hcd
libata 133760 3 ata_generic,ahci,pata_atiixp
nls_base 6377 1 usbcore
scsi_mod 126517 5 sg,usb_storage,sd_mod,sr_mod,libata
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS690 Host Bridge [1002:7911]
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) [1002:7912] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fde00000-fdffffff
Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:06.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) [1002:7916] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fda00000-00000000fdafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] [1002:4391] (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3c)
Subsystem: Giga-byte Technology Device [1458:4385]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Device [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fa00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
Subsystem: Giga-byte Technology Device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: fdb00000-fdbfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k10temp
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon 2100 [1002:796e] (prog-if 00 [VGA controller])
Subsystem: Giga-byte Technology Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d8000000 (64-bit, prefetchable) [size=128M]
Region 2: Memory at fdfe0000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at ee00 [size=256]
Region 5: Memory at fde00000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: radeon
01:05.2 Audio device [0403]: ATI Technologies Inc Radeon X1200 Series Audio Controller [1002:7919]
Subsystem: Giga-byte Technology Device [1458:7919]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fdffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 25
Region 0: I/O ports at de00 [size=256]
Region 2: Memory at fdaff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fdae0000 (64-bit, prefetchable) [size=64K]
[virtual] Expansion ROM at fda00000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
** USB devices:
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 04d9:048e Holtek Semiconductor, Inc. Optical Mouse
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 006: ID 152d:2336 JMicron Technology Corp. / JMicron USA Technology Corp. Hard Disk Drive
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.2
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=ISO-8859-1) (ignored: LC_ALL set to en_US)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-35 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf-show failed
Reply to: