--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.25-2-vserver-686: Should provide linux-image-2.6-vserver-686 package
- From: Kapil Hari Paranjape <kapil@imsc.res.in>
- Date: Mon, 14 Jul 2008 16:30:16 +0530
- Message-id: <20080714110016.GA6698@imsc.res.in>
Package: linux-image-2.6.25-2-vserver-686
Version: 2.6.25-6
Severity: normal
Hello,
The package(s) *-modules-2.6-vserver-686 depend on
linux-latest-modules-2.6.25-2-vserver-686 which is usually provided
by a package like linux-image-2.6-vserver-686.
However, there is no such (pseudo)-package so that the modules
packages that do not specify a version of the kernel are
un-installable.
Since those packages are merely pseudo-packages this is a "normal"
severity. Still this issue could confuse users.
Regards,
Kapil.
-- Package-specific info:
** Version:
Linux version 2.6.25-2-vserver-686 (Debian 2.6.25-6) (maks@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 SMP Fri Jun 27 05:31:46 UTC 2008
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.25-2-vserver-686 root=/dev/mapper/store-nroot ro quiet
** Not tainted
** Kernel log:
[ 1698.915207] PM: Writing back config space on device 0000:02:08.0 at offset 5 (was 1, writing 7001)
[ 1698.915216] PM: Writing back config space on device 0000:02:08.0 at offset 4 (was 0, writing d0201000)
[ 1698.915222] PM: Writing back config space on device 0000:02:08.0 at offset 3 (was 0, writing 4208)
[ 1698.915232] PM: Writing back config space on device 0000:02:08.0 at offset 1 (was 2900000, writing 2900117)
[ 1698.932191] serial 00:09: activated
[ 1698.933066] parport_pc 00:0a: activated
[ 1698.934571] e100: lan: e100_watchdog: link up, 100Mbps, full-duplex
[ 1699.896036] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 1699.897956] hda: UDMA/100 mode selected
[ 1700.103727] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 1700.103727] hdc: UDMA/33 mode selected
[ 1702.823068] PM: Writing back config space on device 0000:00:02.0 at offset 1 (was 900007, writing 900003)
[ 1702.823068] PM: Writing back config space on device 0000:00:02.1 at offset 1 (was 900007, writing 900003)
[ 1702.839218] Restarting tasks ... done.
[ 4641.194875] PM: Syncing filesystems ... done.
[ 4641.194940] Freezing user space processes ... (elapsed 0.00 seconds) done.
[ 4641.195705] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
[ 4641.195797] Suspending console(s)
[ 4641.195801] drm_sysfs_suspend
[ 4641.210309] drm_sysfs_suspend
[ 4642.863491] parport_pc 00:0a: disabled
[ 4642.863748] serial 00:09: disabled
[ 4642.879036] wifi: Going into suspend...
[ 4642.879079] ACPI: PCI interrupt for device 0000:02:02.0 disabled
[ 4642.879088] ACPI handle has no context!
[ 4642.895324] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[ 4642.911244] ACPI: PCI interrupt for device 0000:00:1f.5 disabled
[ 4642.911429] ACPI: PCI interrupt for device 0000:00:1d.7 disabled
[ 4642.930378] ACPI: PCI interrupt for device 0000:00:1d.2 disabled
[ 4642.930410] ACPI: PCI interrupt for device 0000:00:1d.1 disabled
[ 4642.930446] ACPI: PCI interrupt for device 0000:00:1d.0 disabled
[ 4642.933061] ACPI: Preparing to enter system sleep state S3
[ 4642.942896] Disabling non-boot CPUs ...
[ 4642.942896] Intel machine check architecture supported.
[ 4642.942896] Intel machine check reporting enabled on CPU#0.
[ 4642.942896] Back to C!
[ 4642.950917] ACPI: EC: missing OBF confirmation, don't expect it any longer.
[ 4642.958930] ACPI: EC: missing write data confirmation, don't expect it any longer.
[ 4643.047659] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 4643.047668] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 4643.047687] PM: Writing back config space on device 0000:00:02.1 at offset 5 (was 0, writing d0080000)
[ 4643.047692] PM: Writing back config space on device 0000:00:02.1 at offset 4 (was 8, writing e8000008)
[ 4643.047701] PM: Writing back config space on device 0000:00:02.1 at offset 1 (was 900000, writing 900003)
[ 4643.062996] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 4643.063007] PCI: Enabling device 0000:00:1d.0 (0000 -> 0001)
[ 4643.063011] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 4643.063022] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 4643.063029] PM: Writing back config space on device 0000:00:1d.0 at offset f (was 100, writing 10b)
[ 4643.063047] PM: Writing back config space on device 0000:00:1d.0 at offset 8 (was 1, writing 1821)
[ 4643.063079] usb usb1: root hub lost power or was reset
[ 4643.063101] PCI: Enabling device 0000:00:1d.1 (0000 -> 0001)
[ 4643.063105] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 4643.063116] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 4643.063126] PM: Writing back config space on device 0000:00:1d.1 at offset f (was 200, writing 20b)
[ 4643.063140] PM: Writing back config space on device 0000:00:1d.1 at offset 8 (was 1, writing 1841)
[ 4643.063177] usb usb2: root hub lost power or was reset
[ 4643.063201] PCI: Enabling device 0000:00:1d.2 (0000 -> 0001)
[ 4643.063205] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 4643.063216] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 4643.063223] PM: Writing back config space on device 0000:00:1d.2 at offset f (was 300, writing 30b)
[ 4643.063241] PM: Writing back config space on device 0000:00:1d.2 at offset 8 (was 1, writing 1861)
[ 4643.063272] usb usb3: root hub lost power or was reset
[ 4643.081734] PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
[ 4643.081742] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
[ 4643.081754] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 4643.081769] PM: Writing back config space on device 0000:00:1d.7 at offset f (was 400, writing 40b)
[ 4643.081793] PM: Writing back config space on device 0000:00:1d.7 at offset 4 (was 0, writing d0100000)
[ 4643.081805] PM: Writing back config space on device 0000:00:1d.7 at offset 1 (was 2900006, writing 2900106)
[ 4643.081886] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 4643.081926] PM: Writing back config space on device 0000:00:1f.1 at offset 9 (was 0, writing 20000000)
[ 4643.081942] PM: Writing back config space on device 0000:00:1f.1 at offset 1 (was 2800005, writing 2800007)
[ 4643.081955] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 4643.082016] PM: Writing back config space on device 0000:00:1f.5 at offset 1 (was 2900007, writing 2900003)
[ 4643.082032] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 4643.082042] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 4644.106983] PM: Writing back config space on device 0000:00:1f.6 at offset 1 (was 2900005, writing 2900001)
[ 4644.107003] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
[ 4644.107014] PCI: Setting latency timer of device 0000:00:1f.6 to 64
[ 4645.250662] wifi: Coming out of suspend...
[ 4645.266628] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKF] -> GSI 11 (level, low) -> IRQ 11
[ 4645.383327] ipw2200: Radio disabled by module parameter.
[ 4645.383350] PM: Writing back config space on device 0000:02:08.0 at offset f (was 38080100, writing 3808010b)
[ 4645.383367] PM: Writing back config space on device 0000:02:08.0 at offset 5 (was 1, writing 7001)
[ 4645.383376] PM: Writing back config space on device 0000:02:08.0 at offset 4 (was 0, writing d0201000)
[ 4645.383381] PM: Writing back config space on device 0000:02:08.0 at offset 3 (was 0, writing 4208)
[ 4645.383391] PM: Writing back config space on device 0000:02:08.0 at offset 1 (was 2900000, writing 2900117)
[ 4645.400451] serial 00:09: activated
[ 4645.401319] parport_pc 00:0a: activated
[ 4645.402710] e100: lan: e100_watchdog: link up, 100Mbps, full-duplex
[ 4646.370959] hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 4646.697701] hda: UDMA/100 mode selected
[ 4646.698585] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 4646.699589] hdc: UDMA/33 mode selected
[ 4649.108530] PM: Writing back config space on device 0000:00:02.0 at offset 1 (was 900007, writing 900003)
[ 4649.108530] PM: Writing back config space on device 0000:00:02.1 at offset 1 (was 900007, writing 900003)
[ 4649.109447] Restarting tasks ... <3>hub 2-0:1.0: over-current change on port 1
[ 4649.130846] done.
[ 4649.225492] hub 2-0:1.0: over-current change on port 2
[ 4649.349473] hub 4-0:1.0: over-current change on port 3
[ 4649.453532] hub 4-0:1.0: over-current change on port 4
** Loaded modules:
Module Size Used by
i915 27648 2
drm 72280 3 i915
rfcomm 36368 0
l2cap 22784 5 rfcomm
bluetooth 52900 4 rfcomm,l2cap
pktcdvd 32188 1
dummy 3424 0
xt_pkttype 1952 1
nf_conntrack_ipv4 16616 1
xt_state 2496 1
nf_conntrack 59892 2 nf_conntrack_ipv4,xt_state
iptable_filter 3424 1
ip_tables 13168 1 iptable_filter
x_tables 15716 3 xt_pkttype,xt_state,ip_tables
ext2 67304 1
fuse 44348 1
tun 11072 1
cpufreq_userspace 3812 0
cpufreq_conservative 7432 0
cpufreq_stats 5216 0
cpufreq_powersave 1856 0
cpufreq_ondemand 8428 1
p4_clockmod 5380 0
speedstep_lib 5316 1 p4_clockmod
freq_table 4512 3 cpufreq_stats,cpufreq_ondemand,p4_clockmod
ide_generic 1376 0 [permanent]
pcmcia 36044 0
snd_intel8x0m 16684 0
joydev 11328 0
ipw2200 130760 0
ieee80211 30632 1 ipw2200
ieee80211_crypt 5860 1 ieee80211
firmware_class 9088 2 pcmcia,ipw2200
yenta_socket 24300 1
rsrc_nonstatic 11584 1 yenta_socket
pcmcia_core 36436 3 pcmcia,yenta_socket,rsrc_nonstatic
battery 8448 0
ac 4448 0
snd_intel8x0 31740 0
snd_ac97_codec 91300 2 snd_intel8x0m,snd_intel8x0
bay 6176 0
ac97_bus 1952 1 snd_ac97_codec
snd_pcm_oss 37824 0
snd_mixer_oss 14880 1 snd_pcm_oss
snd_pcm 68228 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_seq_dummy 3780 0
snd_seq_oss 28544 0
snd_seq_midi 8064 0
snd_rawmidi 22528 1 snd_seq_midi
snd_seq_midi_event 6976 2 snd_seq_oss,snd_seq_midi
snd_seq 45872 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
serio_raw 6532 0
button 8240 0
intel_agp 25084 1
snd_timer 21320 2 snd_pcm,snd_seq
snd_seq_device 7564 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
thinkpad_acpi 52864 0
i2c_i801 9520 0
parport_pc 25860 0
parport 33868 1 parport_pc
evdev 11328 1
psmouse 35920 0
nvram 8396 1 thinkpad_acpi
rng_core 4900 0
i2c_core 22548 1 i2c_i801
snd 48772 11 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
agpgart 31720 3 drm,intel_agp
shpchp 29716 0
pci_hotplug 26980 1 shpchp
soundcore 7488 1 snd
snd_page_alloc 9992 3 snd_intel8x0m,snd_intel8x0,snd_pcm
pcspkr 3136 0
rtc 14272 1
ext3 123208 6
jbd 43444 1 ext3
mbcache 8260 2 ext2,ext3
sha256_generic 11520 0
aes_i586 8256 2
aes_generic 29160 1 aes_i586
cbc 4256 1
dm_crypt 14788 1
crypto_blkcipher 18116 3 cbc,dm_crypt
dm_mirror 25316 0
dm_snapshot 17444 0
dm_mod 56072 20 dm_crypt,dm_mirror,dm_snapshot
ide_cd_mod 32864 1
cdrom 31872 2 pktcdvd,ide_cd_mod
ide_disk 13952 3
ata_generic 8004 0
libata 142288 1 ata_generic
scsi_mod 138668 1 libata
piix 7176 0 [permanent]
e100 32716 0
mii 5248 1 e100
ide_pci_generic 4228 0 [permanent]
ide_core 100312 5 ide_generic,ide_cd_mod,ide_disk,piix,ide_pci_generic
ehci_hcd 32620 0
uhci_hcd 22352 0
usbcore 130032 3 ehci_hcd,uhci_hcd
dock 10448 2 bay,libata
thermal 19100 0
processor 39660 2 thermal
fan 5636 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3580] (rev 02)
Subsystem: IBM Device [1014:055c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at <unassigned> (32-bit, prefetchable)
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:00.1 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3584] (rev 02)
Subsystem: IBM Device [1014:055d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 System peripheral [0880]: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller [8086:3585] (rev 02)
Subsystem: IBM Device [1014:055e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller [0300]: Intel Corporation 82852/855GM Integrated Graphics Device [8086:3582] (rev 02)
Subsystem: IBM Device [1014:0557]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at 1800 [size=8]
Capabilities: <access denied>
Kernel modules: intelfb
00:02.1 Display controller [0380]: Intel Corporation 82852/855GM Integrated Graphics Device [8086:3582] (rev 02)
Subsystem: IBM Device [1014:0557]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at e8000000 (32-bit, prefetchable) [disabled] [size=128M]
Region 1: Memory at d0080000 (32-bit, non-prefetchable) [disabled] [size=512K]
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01)
Subsystem: IBM Device [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01)
Subsystem: IBM Device [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 01)
Subsystem: IBM Device [1014:052d]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 01) (prog-if 20)
Subsystem: IBM Device [1014:052e]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at d0100000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 81)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=05, sec-latency=64
I/O behind bridge: 00003000-00007fff
Memory behind bridge: d0200000-dfffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge [8086:24cc] (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE Controller [8086:24ca] (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: IBM Device [1014:052d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1810 [size=16]
Region 5: Memory at 20000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller [8086:24c3] (rev 01)
Subsystem: IBM Device [1014:052d]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01)
Subsystem: IBM Device [1014:0554]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 1c00 [size=256]
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at d0100c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at d0100800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: Intel ICH
Kernel modules: snd-intel8x0
00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller [8086:24c6] (rev 01)
Subsystem: IBM Device [1014:0559]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 2400 [size=256]
Region 1: I/O ports at 2000 [size=128]
Capabilities: <access denied>
Kernel driver in use: Intel ICH Modem
Kernel modules: snd-intel8x0m
02:00.0 CardBus bridge [0607]: Texas Instruments PCI1510 PC card Cardbus Controller [104c:ac56]
Subsystem: IBM Device [1014:0512]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=04, sec-latency=176
Memory window 0: f0000000-f3fff000 (prefetchable)
Memory window 1: d4000000-d7fff000
I/O window 0: 00003000-000030ff
I/O window 1: 00003400-000034ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
02:02.0 Network controller [0280]: Intel Corporation PRO/Wireless 2200BG Network Connection [8086:4220] (rev 05)
Subsystem: Intel Corporation Device [8086:2712]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ipw2200
Kernel modules: ipw2200
02:08.0 Ethernet controller [0200]: Intel Corporation 82801DB PRO/100 VE (MOB) Ethernet Controller [8086:103d] (rev 81)
Subsystem: IBM Device [1014:0522]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0201000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 7000 [size=64]
Capabilities: <access denied>
Kernel driver in use: e100
Kernel modules: eepro100, e100
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'unstable')
Architecture: i386 (i686)
Kernel: Linux 2.6.25-2-vserver-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.25-2-vserver-686 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92e tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.25-2-vserver-686 recommends:
ii libc6-i686 2.7-10 GNU C Library: Shared libraries [i
-- debconf information:
linux-image-2.6.25-2-vserver-686/preinst/failed-to-move-modules-2.6.25-2-vserver-686:
linux-image-2.6.25-2-vserver-686/postinst/depmod-error-2.6.25-2-vserver-686: false
linux-image-2.6.25-2-vserver-686/prerm/would-invalidate-boot-loader-2.6.25-2-vserver-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.25-2-vserver-686/postinst/old-initrd-link-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/preinst/elilo-initrd-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/preinst/abort-overwrite-2.6.25-2-vserver-686:
linux-image-2.6.25-2-vserver-686/postinst/kimage-is-a-directory:
linux-image-2.6.25-2-vserver-686/postinst/bootloader-error-2.6.25-2-vserver-686:
linux-image-2.6.25-2-vserver-686/postinst/create-kimage-link-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/postinst/old-dir-initrd-link-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/preinst/abort-install-2.6.25-2-vserver-686:
linux-image-2.6.25-2-vserver-686/prerm/removing-running-kernel-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/preinst/overwriting-modules-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/preinst/lilo-has-ramdisk:
linux-image-2.6.25-2-vserver-686/postinst/bootloader-test-error-2.6.25-2-vserver-686:
linux-image-2.6.25-2-vserver-686/preinst/lilo-initrd-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/preinst/initrd-2.6.25-2-vserver-686:
linux-image-2.6.25-2-vserver-686/preinst/bootloader-initrd-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/postinst/old-system-map-link-2.6.25-2-vserver-686: true
linux-image-2.6.25-2-vserver-686/postinst/depmod-error-initrd-2.6.25-2-vserver-686: false
--- End Message ---