Bug#646151: linux-image-2.6.32-5-686: Wake-on-lan fails after upgrade to squeeze for Dell Optiplex GX150
Package: linux-2.6
Version: 2.6.32-38
Severity: normal
Remark:
As problem seemed to be related to Bug#619371, it was first reported as
info to this bug. On request of Jonathan Nieder I open a new Bug for it.
After upgrading my working wake-on-lan configuration on a Dell Optiplex
GX150 from lenny to squeeze, wake-on-lan does not work anymore.
To get wake-on-lan to work in lenny I had to add a file
/etc/modprobe.d/wol.conf with contents
options 3c59x enable_wol=1
and set
NETDOWN=no
in /etc/default/halt
(3c59X does not support ethtool, therefore the module parameter is needed)
Correct function could be checked by active LEDs on ethernet-connector
after power-off.
After upgrade to squeeze, LEDs are off after power-off and wake-on-lan
does not work. I tried several things (remove shutting down of
eth0 in /etc/init.d/networking, 3c59x-module remove and load at
/etc/init.d/halt, fiddling with /proc/acpi/wakeup, checking and updating
/sys/bus/pci/devices/xxx/power/wakeup), but nothing helped in any way.
Furtheron I installed an additional ethernet-card:
01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
But all things I tried were not successful with this card, too.
I now just took the source of the lenny-kernel 2.6.26, deactivated
CONFIG_SYSFS_DEPRECATED in the config and built a kernel package. I then
installed this kernel-package on the system without changing anything
else. I then booted this kernel and wake-on-lan works again in squeeze
like in lenny before (with the internal 3com-ethernet).
So something is broken with wake-on-lan in 2.6.32 (maybe related to the
acpi-config of the chipset?)
If needed I can provide further information, perform tests or build
special kernel-versions.
(wake-on-lan is triggered using magic-packet from another linux system
with wakeonlan and from logitech squeezeboxes)
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-38) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Mon Oct 3 04:15:24 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=bf8b665b-0362-4e0b-9106-d0c376484765 ro quiet
** Not tainted
** Kernel log:
[ 2.296327] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 2.296335] usb usb3: SerialNumber: 0000:00:1f.4
[ 2.296828] usb usb3: configuration #1 chosen from 1 choice
[ 2.297042] hub 3-0:1.0: USB hub found
[ 2.297077] hub 3-0:1.0: 2 ports detected
[ 2.297964] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[ 2.297973] PCI: setting IRQ 10 as level-triggered
[ 2.297985] uhci_hcd 0000:01:08.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 2.298008] uhci_hcd 0000:01:08.0: UHCI Host Controller
[ 2.298038] uhci_hcd 0000:01:08.0: new USB bus registered, assigned bus number 4
[ 2.298087] uhci_hcd 0000:01:08.0: irq 10, io base 0x0000e8e0
[ 2.298215] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.298225] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.298233] usb usb4: Product: UHCI Host Controller
[ 2.298240] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 2.298247] usb usb4: SerialNumber: 0000:01:08.0
[ 2.298715] usb usb4: configuration #1 chosen from 1 choice
[ 2.298934] hub 4-0:1.0: USB hub found
[ 2.298968] hub 4-0:1.0: 2 ports detected
[ 2.299144] uhci_hcd 0000:01:08.1: PCI INT B -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 2.299163] uhci_hcd 0000:01:08.1: UHCI Host Controller
[ 2.299191] uhci_hcd 0000:01:08.1: new USB bus registered, assigned bus number 5
[ 2.299239] uhci_hcd 0000:01:08.1: irq 11, io base 0x0000e8c0
[ 2.299359] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.299368] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.299376] usb usb5: Product: UHCI Host Controller
[ 2.299383] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 2.299390] usb usb5: SerialNumber: 0000:01:08.1
[ 2.299803] usb usb5: configuration #1 chosen from 1 choice
[ 2.300080] hub 5-0:1.0: USB hub found
[ 2.300117] hub 5-0:1.0: 2 ports detected
[ 2.324199] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 2.324298] 8139cp 0000:01:07.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 2.368469] ata_piix 0000:00:1f.1: version 2.13
[ 2.368627] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 2.371242] scsi0 : ata_piix
[ 2.372921] scsi1 : ata_piix
[ 2.373340] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 2.373351] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 2.381807] 8139too Fast Ethernet driver 0.9.28
[ 2.382657] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
[ 2.382666] PCI: setting IRQ 9 as level-triggered
[ 2.382677] 8139too 0000:01:07.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
[ 2.385578] eth1: RealTek RTL8139 at 0xec00, 00:08:54:53:60:e9, IRQ 9
[ 2.537848] ata1.00: ATA-6: WDC WD2500JB-57GVC0, 21.02J21, max UDMA/100
[ 2.537860] ata1.00: 488397168 sectors, multi 8: LBA48
[ 2.544827] ata2.00: ATAPI: GCR-8481B, 1.06, max UDMA/33
[ 2.553683] ata1.00: configured for UDMA/100
[ 2.554024] scsi 0:0:0:0: Direct-Access ATA WDC WD2500JB-57G 21.0 PQ: 0 ANSI: 5
[ 2.560993] ata2.00: configured for UDMA/33
[ 2.574883] scsi 1:0:0:0: CD-ROM HL-DT-ST CD-ROM GCR-8481B 1.06 PQ: 0 ANSI: 5
[ 2.648165] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[ 2.648373] sd 0:0:0:0: [sda] Write Protect is off
[ 2.648383] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.648469] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.648957] sda:sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 2.656027] Uniform CD-ROM driver Revision: 3.20
[ 2.657205] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.681041] sda1 sda2 sda3 < sda5 sda6 sda7 >
[ 2.707178] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.765205] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.766747] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.281087] PM: Starting manual resume from disk
[ 3.281102] PM: Resume from partition 8:5
[ 3.281107] PM: Checking hibernation image.
[ 3.281466] PM: Error -22 checking image file
[ 3.281472] PM: Resume from disk failed.
[ 3.380216] kjournald starting. Commit interval 5 seconds
[ 3.380252] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.770704] udev[250]: starting version 164
[ 5.440094] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.613857] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 5.613893] ACPI: Power Button [VBTN]
[ 5.614229] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 5.614243] ACPI: Power Button [PWRF]
[ 5.634595] processor LNXCPU:00: registered as cooling_device0
[ 5.674982] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 5.703062] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 5.768754] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 5.777693] parport_pc 00:0b: reported by Plug and Play ACPI
[ 5.777805] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[ 5.785780] i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 5.785807] i801_smbus 0000:00:1f.3: Enabling SMBus device
[ 5.820220] Intel 82802 RNG detected
[ 6.450225] input: PS/2 Logitech Mouse as /devices/platform/i8042/serio1/input/input4
[ 6.663483] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 6.663527] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 7.228067] intel8x0: white list rate for 1028:00be is 44100
[ 8.191115] Adding 497972k swap on /dev/sda5. Priority:-1 extents:1 across:497972k
[ 8.541902] EXT3 FS on sda1, internal journal
[ 8.808689] loop: module loaded
[ 9.627310] kjournald starting. Commit interval 5 seconds
[ 9.627995] EXT3 FS on sda7, internal journal
[ 9.628049] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.728059] 3c59x 0000:01:0c.0: restoring config space at offset 0xf (was 0xa0a0100, writing 0xa0a010b)
[ 10.728077] 3c59x 0000:01:0c.0: restoring config space at offset 0xc (was 0x0, writing 0xfe000000)
[ 10.728099] 3c59x 0000:01:0c.0: restoring config space at offset 0x3 (was 0x0, writing 0x4008)
[ 10.728112] 3c59x 0000:01:0c.0: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100117)
[ 10.729090] eth0: setting full-duplex.
[ 20.852062] eth0: no IPv6 routers present
** Model information
not available
** Loaded modules:
Module Size Used by
loop 9769 0
snd_intel8x0 19595 0
snd_ac97_codec 79200 1 snd_intel8x0
ac97_bus 710 1 snd_ac97_codec
snd_pcm 47226 2 snd_intel8x0,snd_ac97_codec
snd_seq 35463 0
snd_timer 12270 2 snd_pcm,snd_seq
snd_seq_device 3673 1 snd_seq
snd 34423 6 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_seq,snd_timer,snd_seq_device
psmouse 44809 0
soundcore 3450 1 snd
intel_rng 1965 0
i2c_i801 6462 0
parport_pc 15799 0
shpchp 21220 0
dcdbas 3892 0
parport 22554 1 parport_pc
pcspkr 1207 0
evdev 5609 3
serio_raw 2916 0
processor 26327 0
button 3598 0
snd_page_alloc 5045 2 snd_intel8x0,snd_pcm
i2c_core 12787 1 i2c_i801
rng_core 2178 1 intel_rng
pci_hotplug 18545 1 shpchp
ext3 94396 2
jbd 32317 1 ext3
mbcache 3762 1 ext3
sg 19937 0
sr_mod 10770 0
sd_mod 26005 4
cdrom 26487 1 sr_mod
crc_t10dif 1012 1 sd_mod
ata_generic 2247 0
8139too 14949 0
ata_piix 17736 3
8139cp 13421 0
uhci_hcd 16057 0
libata 115869 2 ata_generic,ata_piix
thermal 9206 0
3c59x 25036 0
ehci_hcd 28693 0
floppy 40923 0
mii 2714 3 8139too,8139cp,3c59x
usbcore 98969 3 uhci_hcd,ehci_hcd
nls_base 4541 1 usbcore
scsi_mod 104853 4 sg,sr_mod,sd_mod,libata
thermal_sys 9378 2 processor,thermal
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
#allow-hotplug eth0
#iface eth0 inet dhcp
auto eth0
iface eth0 inet static
address 192.168.0.239
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
gateway 192.168.0.254
dns-nameservers 192.168.0.254
dns-search local.priv
# post-up ethtool -s eth0 wol g
# post-down ethtool -s eth0 wol g
iface wlan0 inet dhcp
wpa_conf /etc/wpa_supplicant.conf
iface wlan1 inet dhcp
wpa_conf /etc/wpa_supplicant.conf
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
link/ether 00:b0:d0:bc:10:12 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.239/24 brd 192.168.0.255 scope global eth0
inet6 fe80::2b0:d0ff:febc:1012/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:08:54:53:60:e9 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 910 17 0 0 0 0 0 0 910 17 0 0 0 0 0 0
eth0: 2703893 2123 0 0 511 0 0 0 2334463 3909 0 0 0 1020 1530 0
eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
2114 total packets received
0 forwarded
0 incoming packets discarded
2114 incoming packets delivered
1838 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
32 active connections openings
16 passive connection openings
1 failed connection attempts
1 connection resets received
2 connections established
1895 segments received
1691 segments send out
0 segments retransmited
0 bad segments received.
4 resets sent
Udp:
159 packets received
0 packets to unknown port received.
0 packet receive errors
147 packets sent
UdpLite:
TcpExt:
13 TCP sockets finished time wait in fast timer
22 delayed acks sent
Quick ack mode was activated 3 times
4 packets directly queued to recvmsg prequeue.
879 packet headers predicted
155 acknowledgments not containing data payload received
826 predicted acknowledgments
IpExt:
InBcastPkts: 90
OutBcastPkts: 15
InOctets: 576645
OutOctets: 208929
InBcastOctets: 10903
OutBcastOctets: 660
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub [8086:1130] (rev 02)
Subsystem: Dell Device [1028:00be]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation 82815 Chipset Graphics Controller (CGC) [8086:1132] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:00be]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at ff080000 (32-bit, non-prefetchable) [size=512K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fd000000-feffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:1f.0 ISA bridge [0601]: Intel Corporation 82801BA ISA Bridge (LPC) [8086:2440] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.1 IDE interface [0101]: Intel Corporation 82801BA IDE U100 Controller [8086:244b] (rev 02) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at ffa0 [size=16]
Kernel driver in use: ata_piix
00:1f.2 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB Controller #1 [8086:2442] (rev 02) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at ff80 [size=32]
Kernel driver in use: uhci_hcd
00:1f.3 SMBus [0c05]: Intel Corporation 82801BA/BAM SMBus Controller [8086:2443] (rev 02)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at dcd0 [size=16]
Kernel driver in use: i801_smbus
00:1f.4 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB Controller #1 [8086:2444] (rev 02) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at ff60 [size=32]
Kernel driver in use: uhci_hcd
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801BA/BAM AC'97 Audio Controller [8086:2445] (rev 02)
Subsystem: Dell Device [1028:00be]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at d800 [size=256]
Region 1: I/O ports at dc40 [size=64]
Kernel driver in use: Intel ICH
01:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at ec00 [size=256]
Region 1: Memory at fdfffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: 8139too
01:08.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at e8e0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
01:08.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at e8c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
01:08.2 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 65) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 11
Region 0: Memory at fdfff800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
01:0c.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 78)
Subsystem: Dell Device [1028:00be]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800 [size=128]
Region 1: Memory at fdfff400 (32-bit, non-prefetchable) [size=128]
Expansion ROM at fe000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: 3c59x
** USB devices:
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.3
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-38 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-38 Binary firmware for various driver
ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
ii grub 0.97-64 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
Reply to: