--- Begin Message ---
Package: linux-2.6
Version: 2.6.32-35
Severity: normal
*** Please type your report below this line ***
I have problems with an RTL8169 Gigabit PCI-card.
It works perfect with 100 base, but when i use an 1000 base switch i got
massive packet loss.
This problem is well known and normally the solution is to use the
driver r8168 instead of r8169.
So I compiled and installed the newest r8168 driver downloaded from realtek.
http://www.realtek.com/downloads/downloadsView.aspx?Langid=1&PNid=5&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false#RTL8111B/RTL8168B/RTL8111/RTL8168%3Cbr%3ERTL8111C/RTL8111CP/RTL8111D%28L%29%3Cbr%3ERTL8168C/RTL8111DP/RTL8111E%3Cbr%3ERTL8168E/RTL8111F
<http://www.realtek.com/downloads/downloadsView.aspx?Langid=1&PNid=5&PFid=5&Level=5&Conn=4&DownTypeID=3&GetDown=false#RTL8111B/RTL8168B/RTL8111/RTL8168%3Cbr%3ERTL8111C/RTL8111CP/RTL8111D%28L%29%3Cbr%3ERTL8168C/RTL8111DP/RTL8111E%3Cbr%3ERTL8168E/RTL8111F>
I followed this german instructions here:
http://wiki.hetzner.de/index.php/Installation_des_r8168-Treibers
Now the driver is loaded and can be found in the driver list with
|# lsmod | grep r81
r8168 29279 0
|But it is not listed by|
ifconfig -a|
I can only see my onboard 100 base as eth1.
The eth2 for the gigabit-card is missing!
The driver is loaded but the eth is not recognized?
This is what you can see with connected 100 base to eth2:
|root@PC:# ifconfig -a
eth1 Link encap:Ethernet Hardware Adresse 00:19:66:38:2f:ff
UP BROADCAST MULTICAST MTU:1500 Metrik:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:22 Basisadresse:0xc000
eth2 Link encap:Ethernet Hardware Adresse 00:e0:51:9b:00:3b
inet Adresse:192.168.1.10 Bcast:192.168.1.255
Maske:255.255.255.0
inet6-Adresse: fe80::2e0:51ff:fe9b:3b/64
Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:4732 errors:0 dropped:0 overruns:0 frame:0
TX packets:4267 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:4333246 (4.1 MiB) TX bytes:505534 (493.6 KiB)
Interrupt:17 Basisadresse:0x8c00
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:16436 Metrik:1
RX packets:140 errors:0 dropped:0 overruns:0 frame:0
TX packets:140 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:8776 (8.5 KiB) TX bytes:8776 (8.5 KiB)
vboxnet0 Link encap:Ethernet Hardware Adresse 0a:00:27:00:00:00
BROADCAST MULTICAST MTU:1500 Metrik:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
It seems that many people are affected by this problem.
A solution to solve this problem would really be fine.
Regards
Karsten
|-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-35) (dannf@debian.org) (gcc
version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Tue Jun 14 09:42:28 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64
root=UUID=7380c441-7e12-4401-9488-0c4996ecc9b6 ro quiet
** Tainted: P (1)
* Proprietary module has been loaded.
** Kernel log:
[ 2.295762] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.295781] sd 2:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 2.295921] sda: sda1 sda2 sda3 sda4 <sr0: scsi3-mmc drive: 48x/48x
cd/rw xa/form2 cdda tray
[ 2.302497] Uniform CD-ROM driver Revision: 3.20
[ 2.302602] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.305748] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 2.305817] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 2.310630] sda5 sda6 sda7 >
[ 2.333345] sd 2:0:0:0: [sda] Attached SCSI disk
[ 2.334867] usb 1-2.1: New USB device found, idVendor=058f,
idProduct=6366
[ 2.334871] usb 1-2.1: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 2.334873] usb 1-2.1: Product: Mass Storage Device
[ 2.334875] usb 1-2.1: Manufacturer: Generic
[ 2.334876] usb 1-2.1: SerialNumber: 058F0O1111B
[ 2.334997] usb 1-2.1: configuration #1 chosen from 1 choice
[ 2.341782] sr 1:0:0:0: Attached scsi generic sg0 type 5
[ 2.342192] sr 1:0:1:0: Attached scsi generic sg1 type 5
[ 2.342569] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 2.346721] Initializing USB Mass Storage driver...
[ 2.347014] scsi4 : SCSI emulation for USB Mass Storage devices
[ 2.347111] usbcore: registered new interface driver usb-storage
[ 2.347113] USB Mass Storage support registered.
[ 2.347649] usb-storage: device found at 3
[ 2.347652] usb-storage: waiting for device to settle before scanning
[ 4.453738] EXT4-fs (sda2): mounted filesystem with ordered data mode
[ 5.627029] udev[450]: starting version 164
[ 5.811959] processor LNXCPU:00: registered as cooling_device0
[ 5.812003] processor LNXCPU:01: registered as cooling_device1
[ 5.837288] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 5.870448] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
[ 5.870457] ACPI: Power Button [PWRB]
[ 5.870526] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 5.870529] ACPI: Power Button [PWRF]
[ 5.905455] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 6.028021] i2c i2c-0: nForce2 SMBus adapter at 0x5000
[ 6.028070] i2c i2c-1: nForce2 SMBus adapter at 0x5040
[ 6.033055] k8temp 0000:00:18.3: Temperature readouts might be wrong
- check erratum #141
[ 6.045656] parport_pc 00:06: reported by Plug and Play ACPI
[ 6.045702] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 6.092896] EDAC MC: Ver: 2.1.0 Jun 14 2011
[ 6.103168] EDAC amd64_edac: Ver: 3.2.0 Jun 14 2011
[ 6.103392] EDAC amd64: This node reports that Memory ECC is
currently disabled, set F3x44[22] (0000:00:18.3).
[ 6.103402] EDAC amd64: ECC disabled in the BIOS or no ECC
capability, module will not load.
[ 6.103403] Either enable ECC checking or force module loading by
setting 'ecc_enable_override'.
[ 6.103405] (Note that use of the override may cause unknown side
effects.)
[ 6.103431] amd64_edac: probe of 0000:00:18.2 failed with error -22
[ 6.107444] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.120666] udev[463]: renamed network interface eth0 to eth2
[ 6.489661] nvidia: module license 'NVIDIA' taints kernel.
[ 6.489666] Disabling lock debugging due to kernel taint
[ 6.858195] input: ImPS/2 Generic Wheel Mouse as
/devices/platform/i8042/serio1/input/input5
[ 7.117568] nvidia 0000:01:00.0: PCI INT A -> Link[LNKD] -> GSI 17
(level, low) -> IRQ 17
[ 7.117582] vgaarb: device changed decodes:
PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 7.117966] NVRM: loading NVIDIA UNIX x86_64 Kernel Module
260.19.21 Thu Nov 4 21:16:27 PDT 2010
[ 7.344179] usb-storage: device scan complete
[ 7.344769] scsi 4:0:0:0: Direct-Access Multi Flash Reader
1.00 PQ: 0 ANSI: 0
[ 7.345334] sd 4:0:0:0: Attached scsi generic sg3 type 0
[ 7.347877] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 7.937387] ENS1371 0000:02:09.0: PCI INT A -> Link[LNKB] -> GSI 18
(level, low) -> IRQ 18
[ 9.900634] Adding 200772k swap on /dev/sda5. Priority:-1 extents:1
across:200772k
[ 10.082968] loop: module loaded
[ 10.122527] w83627ehf: Found W83627EHG chip at 0x290
[ 15.763092] kjournald starting. Commit interval 5 seconds
[ 15.763401] EXT3 FS on sda3, internal journal
[ 15.763407] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.973749] EXT4-fs (sda7): mounted filesystem with ordered data mode
[ 15.996952] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
[ 16.977731] fuse init (API version 7.13)
[ 17.369012] r8169: eth2: link up
[ 19.818240] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core
Processor 5400+ processors (2 cpu cores) (version 2.20.00)
[ 19.818306] powernow-k8: 0 : fid 0x14 (2800 MHz), vid 0x8
[ 19.818308] powernow-k8: 1 : fid 0x12 (2600 MHz), vid 0xa
[ 19.818310] powernow-k8: 2 : fid 0x10 (2400 MHz), vid 0xc
[ 19.818312] powernow-k8: 3 : fid 0xe (2200 MHz), vid 0xe
[ 19.818314] powernow-k8: 4 : fid 0xc (2000 MHz), vid 0x10
[ 19.818315] powernow-k8: 5 : fid 0xa (1800 MHz), vid 0x10
[ 19.818317] powernow-k8: 6 : fid 0x2 (1000 MHz), vid 0x12
[ 20.140528] Clocksource tsc unstable (delta = -139368087 ns)
[ 20.453237] eth1: no link during initialization.
[ 20.455484] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 21.121728] lp0: using parport0 (interrupt-driven).
[ 21.129890] ppdev: user-space parallel port driver
[ 22.315205] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
[ 22.315223] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x
mode
[ 22.315258] nvidia 0000:01:00.0: putting AGP V3 device into 8x mode
[ 23.265046] vboxdrv: Found 2 processor cores.
[ 23.265558] VBoxDrv: dbg - g_abExecMemory=ffffffffa0ded9a0
[ 23.265584] vboxdrv: fAsync=1 offMin=0x2559 offMax=0x2559
[ 23.266316] vboxdrv: TSC mode is 'asynchronous', kernel timer mode is
'normal'.
[ 23.266320] vboxdrv: Successfully loaded version 4.0.12 (interface
0x00180000).
[ 28.136014] eth2: no IPv6 routers present
[ 38.493188] CPUFREQ: Per core ondemand sysfs interface is deprecated
- up_threshold
[ 38.742484] CPU0 attaching NULL sched-domain.
[ 38.742498] CPU1 attaching NULL sched-domain.
[ 38.764730] CPU0 attaching sched-domain:
[ 38.764738] domain 0: span 0-1 level MC
[ 38.764744] groups: 0 1
[ 38.764757] CPU1 attaching sched-domain:
[ 38.764762] domain 0: span 0-1 level MC
[ 38.764766] groups: 1 0
** Model information
sys_vendor: To Be Filled By O.E.M.
product_name: To Be Filled By O.E.M.
product_version: To Be Filled By O.E.M.
chassis_vendor: To Be Filled By O.E.M.
chassis_version: To Be Filled By O.E.M.
bios_vendor: American Megatrends Inc.
bios_version: P3.20
board_vendor: ASRock
board_name: AM2NF3-VSTA
board_version:
** Loaded modules:
Module Size Used by
vboxnetadp 4683 0
vboxnetflt 15920 0
vboxdrv 1749377 2 vboxnetadp,vboxnetflt
ppdev 5030 0
lp 7462 0
powernow_k8 10978 1
cpufreq_conservative 5162 0
cpufreq_userspace 1992 0
cpufreq_powersave 902 0
cpufreq_stats 2659 0
fuse 50892 1
nls_utf8 1208 1
nls_cp437 5817 1
vfat 7884 1
fat 40038 1 vfat
ext3 106630 1
jbd 37085 1 ext3
w83627ehf 18675 0
hwmon_vid 1828 1 w83627ehf
loop 11799 0
snd_ens1371 16938 2
gameport 7416 1 snd_ens1371
snd_ac97_codec 99186 1 snd_ens1371
ac97_bus 1086 1 snd_ac97_codec
snd_pcm_oss 32591 0
snd_mixer_oss 12606 1 snd_pcm_oss
snd_pcm 60503 3 snd_ens1371,snd_ac97_codec,snd_pcm_oss
snd_seq_midi 4400 0
snd_rawmidi 15515 2 snd_ens1371,snd_seq_midi
snd_seq_midi_event 4628 1 snd_seq_midi
snd_seq 42881 3 snd_seq_midi,snd_seq_midi_event
snd_timer 15582 2 snd_pcm,snd_seq
snd_seq_device 4493 3 snd_seq_midi,snd_rawmidi,snd_seq
snd 46526 14
snd_ens1371,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 4598 1 snd
snd_page_alloc 6249 1 snd_pcm
nvidia 10019576 38
shpchp 26264 0
edac_core 29261 0
psmouse 49937 0
parport_pc 18855 1
parport 27954 3 ppdev,lp,parport_pc
k8temp 3283 0
i2c_nforce2 5280 0
i2c_core 15819 2 nvidia,i2c_nforce2
edac_mce_amd 6433 0
pci_hotplug 21203 1 shpchp
evdev 7352 11
serio_raw 3752 0
button 4650 0
pcspkr 1699 0
processor 29935 1 powernow_k8
ext4 288318 2
mbcache 5050 2 ext3,ext4
jbd2 67015 1 ext4
crc16 1319 1 ext4
usb_storage 39961 0
sg 24069 0
sr_mod 12602 0
cdrom 29415 1 sr_mod
sd_mod 29921 6
crc_t10dif 1276 1 sd_mod
ata_generic 3239 0
ohci_hcd 19343 0
sata_nv 19166 5
thermal 11674 0
pata_amd 9869 0
libata 133760 3 ata_generic,sata_nv,pata_amd
floppy 49087 0
ehci_hcd 32081 0
usbcore 122498 4 usb_storage,ohci_hcd,ehci_hcd
thermal_sys 11942 2 processor,thermal
forcedeth 45448 0
r8169 29279 0
mii 3210 1 r8169
scsi_mod 126517 5 usb_storage,sg,sr_mod,sd_mod,libata
nls_base 6377 5 nls_utf8,nls_cp437,vfat,fat,usbcore
** Network interface configuration:
auto lo
iface lo inet loopback
allow-hotplug eth2
iface eth2 inet static
address 192.168.1.10
netmask 255.255.255.0
network 192.168.1.0
broadcast 192.168.1.255
gateway 192.168.1.1
dns-nameservers 192.168.1.1
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UNKNOWN qlen 1000
link/ether 00:e0:51:9b:00:3b brd ff:ff:ff:ff:ff:ff
inet 192.168.1.10/24 brd 192.168.1.255 scope global eth2
inet6 fe80::2e0:51ff:fe9b:3b/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast
state DOWN qlen 1000
link/ether 00:19:66:38:2f:ff brd ff:ff:ff:ff:ff:ff
4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed
multicast|bytes packets errs drop fifo colls carrier compressed
lo: 10160 160 0 0 0 0 0 0
10160 160 0 0 0 0 0 0
eth2:19774110 21789 0 0 0 0 0 0
3139844 20189 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
vboxnet0: 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
21303 total packets received
0 forwarded
0 incoming packets discarded
21221 incoming packets delivered
20095 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
729 active connections openings
10 passive connection openings
31 failed connection attempts
18 connection resets received
5 connections established
19289 segments received
18288 segments send out
34 segments retransmited
0 bad segments received.
131 resets sent
Udp:
1897 packets received
0 packets to unknown port received.
0 packet receive errors
1746 packets sent
UdpLite:
TcpExt:
263 TCP sockets finished time wait in fast timer
1 time wait sockets recycled by time stamp
3 packets rejects in established connections because of timestamp
864 delayed acks sent
Quick ack mode was activated 11 times
14300 packet headers predicted
1240 acknowledgments not containing data payload received
1704 predicted acknowledgments
3 congestion windows recovered without slow start by DSACK
15 congestion windows recovered without slow start after partial ack
2 timeouts after SACK recovery
22 other TCP timeouts
5 DSACKs sent for old packets
10 DSACKs received
12 connections reset due to unexpected data
10 connections reset due to early user close
1 connections aborted due to timeout
TCPDSACKIgnoredOld: 2
TCPDSACKIgnoredNoUndo: 2
TCPSackShiftFallback: 5
IpExt:
InMcastPkts: 344
OutMcastPkts: 195
InBcastPkts: 10
InOctets: 19454690
OutOctets: 2843368
InMcastOctets: 42479
OutMcastOctets: 23320
InBcastOctets: 2430
*** Device features:
eth1: 0x10803
eth2: 0x180
lo: 0x13865
vboxnet0: 0x0
** PCI devices:
00:00.0 Host bridge [0600]: nVidia Corporation nForce3 250Gb Host Bridge
[10de:00e1] (rev a1)
Subsystem: ASRock Incorporation Motherboard (one of many) [1849:00e1]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at <ignored> (32-bit, prefetchable)
Capabilities: <access denied>
Kernel driver in use: agpgart-amd64
00:01.0 ISA bridge [0601]: nVidia Corporation nForce3 250Gb LPC Bridge
[10de:00e0] (rev a2)
Subsystem: ASRock Incorporation Motherboard (one of many) [1849:00e0]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation nForce 250Gb PCI System
Management [10de:00e4] (rev a1)
Subsystem: ASRock Incorporation Motherboard (one of many) [1849:00e4]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 5080 [size=32]
Region 4: I/O ports at 5000 [size=64]
Region 5: I/O ports at 5040 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
00:02.0 USB Controller [0c03]: nVidia Corporation CK8S USB Controller
[10de:00e7] (rev a1) (prog-if 10 [OHCI])
Subsystem: ASRock Incorporation Motherboard (one of many) [1849:00e7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fbffd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.1 USB Controller [0c03]: nVidia Corporation CK8S USB Controller
[10de:00e7] (rev a1) (prog-if 10 [OHCI])
Subsystem: ASRock Incorporation Motherboard (one of many) [1849:00e7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.2 USB Controller [0c03]: nVidia Corporation nForce3 EHCI USB 2.0
Controller [10de:00e8] (rev a2) (prog-if 20 [EHCI])
Subsystem: ASRock Incorporation Motherboard (one of many) [1849:00e8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fbfffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:05.0 Bridge [0680]: nVidia Corporation CK8S Ethernet Controller
[10de:00df] (rev a2)
Subsystem: ASRock Incorporation Device [1849:00df]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fbffc000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at dc00 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth
00:08.0 IDE interface [0101]: nVidia Corporation CK8S Parallel ATA
Controller (v2.5) [10de:00e5] (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: ASRock Incorporation Motherboard (one of many) [1849:00e5]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[size=1]
Region 4: I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_amd
00:0a.0 IDE interface [0101]: nVidia Corporation nForce3 Serial ATA
Controller [10de:00e3] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASRock Incorporation Motherboard (one of many) [1849:00e3]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 0f80 [size=8]
Region 1: I/O ports at 0f00 [size=4]
Region 2: I/O ports at 0e80 [size=8]
Region 3: I/O ports at 0e00 [size=4]
Region 4: I/O ports at d000 [size=16]
Region 5: I/O ports at c800 [size=128]
Capabilities: <access denied>
Kernel driver in use: sata_nv
00:0b.0 PCI bridge [0604]: nVidia Corporation nForce3 250Gb AGP Host to
PCI Bridge [10de:00e2] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
Memory behind bridge: fc000000-feafffff
Prefetchable memory behind bridge: e0000000-efffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:0e.0 PCI bridge [0604]: nVidia Corporation nForce3 250Gb PCI-to-PCI
Bridge [10de:00ed] (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR+ <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=128
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
01:00.0 VGA compatible controller [0300]: nVidia Corporation G71
[GeForce 7900 GS] [10de:02e3] (rev a2) (prog-if 00 [VGA controller])
Subsystem: XFX Pine Group Inc. Device [1682:4008]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 2: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at feae0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
02:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit
Ethernet [10ec:8169]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at febffc00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at febc0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
02:08.0 Serial controller [0700]: NetMos Technology PCI 9865 Multi-I/O
Controller [9710:9865] (prog-if 02 [16550])
Subsystem: Device [a000:1000]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at e080 [size=8]
Region 1: Memory at febfa000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at febf9000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
02:08.1 Serial controller [0700]: NetMos Technology PCI 9865 Multi-I/O
Controller [9710:9865] (prog-if 02 [16550])
Subsystem: Device [a000:1000]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at e400 [size=8]
Region 1: Memory at febfc000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at febfb000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
02:08.2 Parallel controller [0701]: NetMos Technology PCI 9865 Multi-I/O
Controller [9710:9865] (prog-if 03 [IEEE1284])
Subsystem: Device [a000:2000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 11
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e480 [size=8]
Region 2: Memory at febfe000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at febfd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
02:09.0 Multimedia audio controller [0401]: Ensoniq 5880B [AudioPCI]
[1274:5880] (rev 02)
Subsystem: Ensoniq Sound Blaster 16PCI 4.1ch [1274:8001]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort+ <MAbort+ >SERR- <PERR- INTx-
Latency: 32 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at e000 [size=64]
Capabilities: <access denied>
Kernel driver in use: ENS1371
** USB devices:
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader
Bus 001 Device 002: ID 058f:6254 Alcor Micro Corp. USB Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.2
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration
management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an
initramfs
ii linux-base 2.6.32-35 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
ii firmware-linux-free 2.6.32-35 Binary firmware for various
driver
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.28 Binary firmware for various
driver
ii firmware-linux-nonfree 0.28 Binary firmware for various
driver
pn firmware-qlogic <none> (no description available)
ii firmware-ralink 0.28 Binary firmware for Ralink
wireles
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64:
false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64:
true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
--- End Message ---