Bug#636417: linux-image-3.0.0-1-loongson-2f: loongson-2f linux kernel in stock compiled with ipv6 as module, which conflicts with procps
Package: linux-2.6
Version: 3.0.0-1
Severity: normal
Tags: ipv6
*** Please type your report below this line ***
The loongson-2f stock kernel on debian comes with ipv6 compiled as a
module. However that's not expected by procps. See:
/usr/share/doc/procps/README.Debian
...
ipv6 sysctl keys
----------------
Modern Debian kernel packages have the IPv6 module compiled in by default.
This means that the /proc/sys/net/ipv6 directory exists when the procps
startup script runs.
However if you make your own kernel then you may make ipv6 a module and
get a race condition between the netbase and procps startup scripts. This
is because netbase, by default, causes ipv6 module to be loaded but
they don't (and cannot) depend on each-other.
The solution is to either:
- Not put ipv6 keys into /etc/sysctl.d/* or /etc/sysctl.conf
- Compile the ipv6 module into the kernel
- Load the module early by putting ipv6 into /etc/modules
- Make a init script dependency by adding netbase to the Required-Start
line in /etc/init.d/procps
...
Tha clearly states the debian stock kernels should have no problem
given that they come with ipv6 built inside. However loongson-2f
stock kernels don't comply with this.
This causes failures like:
error: "net.ipv6.bindv6only" is an unknown key
Work around is really simple, just to add ipv6 into /etc/modules,
however that shouldn't be the case for stock kernels according to
procps documentation, and also a bug filed for that purpose last year
(closed already):
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=507788
Any ways, just the loongson-2f kernel not being compliant with procps
suppositions, :-)
Thanks,
Javier.
-- Package-specific info:
** Version:
Linux version 3.0.0-1-loongson-2f (Debian 3.0.0-1)
(ben@decadent.org.uk) (gcc version 4.5.3 (Debian 4.5.3-3) ) #1 Mon Jul
25 21:17:28 UTC 2011
** Command line:
console=tty machtype=lemote-fuloong-2f-box root=/dev/sda6
video=sisfb:1280x1024-24@60 resume=/dev/sda5 PMON_VER=LM6004-1.3.6
EC_VER=undefined machtype=lemote-fuloong-2f-box
** Not tainted
** Kernel log:
[ 2.088000] PM: Hibernation image partition 8:5 present
[ 2.088000] PM: Looking for hibernation image.
[ 2.092000] PM: Image not found (code -22)
[ 2.092000] PM: Hibernation image not present or could not be loaded.
[ 2.092000] registered taskstats version 1
[ 2.092000] /build/buildd-linux-2.6_3.0.0-1-mipsel-TFQf1R/linux-2.6-3.0.0/debian/build/source_mipsel_none/drivers/rtc/hctosys.c:
unable to open rtc device (rtc0)
[ 2.096000] Initializing network drop monitor service
[ 2.120000] EXT3-fs: barriers not enabled
[ 2.128000] kjournald starting. Commit interval 5 seconds
[ 2.128000] EXT3-fs (sda6): mounted filesystem with ordered data mode
[ 2.128000] VFS: Mounted root (ext3 filesystem) readonly on device 8:6.
[ 2.132000] Freeing unused kernel memory: 240k freed
[ 4.312000] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 4.312000] r8169 0000:00:06.0: (unregistered net_device): no PCI
Express capability
[ 4.312000] r8169 0000:00:06.0: eth0: RTL8169sc/8110sc at
0x9000000050072000, 00:23:9e:00:0f:62, XID 18000000 IRQ 36
[ 4.480000] cpufreq: Loongson-2F CPU frequency driver.
[ 4.540000] usbcore: registered new interface driver usbfs
[ 4.556000] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 4.604000] usbcore: registered new interface driver hub
[ 4.612000] rtc0: alarms up to one day, 114 bytes nvram
[ 4.644000] usbcore: registered new device driver usb
[ 4.688000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.744000] PCI: Setting latency timer of device 0000:00:0e.5 to 64
[ 4.744000] ehci_hcd 0000:00:0e.5: EHCI Host Controller
[ 4.776000] ehci_hcd 0000:00:0e.5: new USB bus registered, assigned
bus number 1
[ 4.828000] ehci_hcd 0000:00:0e.5: irq 11, io mem 0x50071000
[ 4.848000] ehci_hcd 0000:00:0e.5: USB 0.0 started, EHCI 1.00
[ 4.888000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.892000] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 4.896000] usb usb1: Product: EHCI Host Controller
[ 4.900000] usb usb1: Manufacturer: Linux 3.0.0-1-loongson-2f ehci_hcd
[ 4.904000] usb usb1: SerialNumber: 0000:00:0e.5
[ 4.924000] hub 1-0:1.0: USB hub found
[ 4.944000] hub 1-0:1.0: 4 ports detected
[ 4.996000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.004000] PCI: Enabling device 0000:00:0e.4 (0000 -> 0002)
[ 5.036000] PCI: Setting latency timer of device 0000:00:0e.4 to 64
[ 5.036000] ohci_hcd 0000:00:0e.4: OHCI Host Controller
[ 5.044000] ohci_hcd 0000:00:0e.4: new USB bus registered, assigned
bus number 2
[ 5.064000] ohci_hcd 0000:00:0e.4: irq 11, io mem 0x50070000
[ 5.156000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.160000] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 5.164000] usb usb2: Product: OHCI Host Controller
[ 5.168000] usb usb2: Manufacturer: Linux 3.0.0-1-loongson-2f ohci_hcd
[ 5.172000] usb usb2: SerialNumber: 0000:00:0e.4
[ 5.180000] hub 2-0:1.0: USB hub found
[ 5.188000] hub 2-0:1.0: 4 ports detected
[ 5.372000] PCI: Setting latency timer of device 0000:00:0e.3 to 64
[ 5.568000] usb 2-3: new low speed USB device number 2 using ohci_hcd
[ 5.804000] usb 2-3: New USB device found, idVendor=04d9, idProduct=1702
[ 5.808000] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 5.812000] usb 2-3: Product: USB Keyboard
[ 5.816000] usb 2-3: Manufacturer:
[ 6.008000] usb 2-4: new low speed USB device number 3 using ohci_hcd
[ 6.176000] input: USB Keyboard as
/devices/pci0000:00/0000:00:0e.4/usb2/2-3/2-3:1.0/input/input0
[ 6.188000] generic-usb 0003:04D9:1702.0001: input,hidraw0: USB HID
v1.10 Keyboard [ USB Keyboard] on usb-0000:00:0e.4-3/input0
[ 6.220000] input: USB Keyboard as
/devices/pci0000:00/0000:00:0e.4/usb2/2-3/2-3:1.1/input/input1
[ 6.232000] generic-usb 0003:04D9:1702.0002: input,hidraw1: USB HID
v1.10 Device [ USB Keyboard] on usb-0000:00:0e.4-3/input1
[ 6.240000] usb 2-4: New USB device found, idVendor=0458, idProduct=003a
[ 6.244000] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.248000] usb 2-4: Product: Optical Mouse
[ 6.252000] usb 2-4: Manufacturer: Genius
[ 6.280000] input: Genius Optical Mouse as
/devices/pci0000:00/0000:00:0e.4/usb2/2-4/2-4:1.0/input/input2
[ 6.296000] generic-usb 0003:0458:003A.0003: input,hidraw2: USB HID
v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:0e.4-4/input0
[ 6.312000] usbcore: registered new interface driver usbhid
[ 6.316000] usbhid: USB HID core driver
[ 9.908000] Adding 3903744k swap on /dev/sda5. Priority:-1
extents:1 across:3903744k
[ 11.060000] EXT3-fs (sda6): using internal journal
[ 11.508000] loop: module loaded
[ 11.652000] fuse init (API version 7.16)
[ 17.520000] EXT3-fs: barriers not enabled
[ 17.532000] kjournald starting. Commit interval 5 seconds
[ 17.536000] EXT3-fs (sda1): using internal journal
[ 17.540000] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 17.744000] EXT4-fs (sda7): mounted filesystem with ordered data
mode. Opts: (null)
[ 17.848000] EXT4-fs (sda8): mounted filesystem with ordered data
mode. Opts: (null)
[ 17.992000] EXT4-fs (sda9): mounted filesystem with ordered data
mode. Opts: (null)
[ 18.128000] EXT4-fs (sda10): mounted filesystem with ordered data
mode. Opts: (null)
[ 18.204000] EXT4-fs (sda11): mounted filesystem with ordered data
mode. Opts: (null)
[ 18.292000] EXT4-fs (sda12): mounted filesystem with ordered data
mode. Opts: (null)
[ 18.372000] EXT4-fs (sda13): mounted filesystem with ordered data
mode. Opts: (null)
[ 18.564000] EXT4-fs (sda14): mounted filesystem with ordered data
mode. Opts: (null)
[ 19.620000] r8169 0000:00:06.0: eth0: link down
[ 20.484000] NET: Registered protocol family 10
[ 20.492000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.184000] r8169 0000:00:06.0: eth0: link up
[ 21.192000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 21.300000] RPC: Registered named UNIX socket transport module.
[ 21.304000] RPC: Registered udp transport module.
[ 21.308000] RPC: Registered tcp transport module.
[ 21.312000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 21.360000] FS-Cache: Loaded
[ 21.448000] FS-Cache: Netfs 'nfs' registered for caching
[ 21.504000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 27.292000] ioctl32(Xorg:1174): Unknown cmd fd(8)
cmd(8004f300){t:'�';sz:4} arg(7fafcec4) on /dev/fb0
[ 27.292000] ioctl32(Xorg:1174): Unknown cmd fd(8)
cmd(80046ef8){t:'n';sz:4} arg(00b5de60) on /dev/fb0
[ 27.300000] sisfb 0000:00:08.0: Invalid ROM contents
[ 31.752000] eth0: no IPv6 routers present
[ 35.940000] sisfb 0000:00:08.0: Invalid ROM contents
[ 35.940000] sisfb 0000:00:08.0: Invalid ROM contents
** Model information
system type : lemote-fuloong-2f-box
cpu model : ICT Loongson-2 V0.3 FPU V0.1
** Loaded modules:
Module Size Used by
cpufreq_stats 3130 0
cpufreq_conservative 6257 0
cpufreq_userspace 2128 0
cpufreq_powersave 1094 0
nfsd 359805 2
nfs 383137 0
lockd 92252 2 nfsd,nfs
fscache 41569 1 nfs
auth_rpcgss 48166 2 nfsd,nfs
nfs_acl 2959 2 nfsd,nfs
sunrpc 234434 6 nfsd,nfs,lockd,auth_rpcgss,nfs_acl
ipv6 378237 26
ext4 424010 8
jbd2 76710 1 ext4
crc16 1447 1 ext4
autofs4 27460 3
fuse 80422 1
loop 18465 0
evdev 11734 5
usbhid 44648 0
hid 93455 1 usbhid
snd_cs5535audio 11665 0
snd_ac97_codec 134508 1 snd_cs5535audio
ac97_bus 1294 1 snd_ac97_codec
snd_pcm 87605 2 snd_cs5535audio,snd_ac97_codec
ohci_hcd 24339 0
snd_seq 62903 0
snd_timer 22681 2 snd_pcm,snd_seq
snd_seq_device 7017 1 snd_seq
snd 72623 6
snd_cs5535audio,snd_ac97_codec,snd_pcm,snd_seq,snd_timer,snd_seq_device
ehci_hcd 46296 0
soundcore 6089 1 snd
rtc_cmos 7696 0
usbcore 176676 4 usbhid,ohci_hcd,ehci_hcd
snd_page_alloc 6989 2 snd_cs5535audio,snd_pcm
loongson2_cpufreq 2827 0
loongson2_clock 2536 1 loongson2_cpufreq
r8169 49164 0
mii 4787 1 r8169
** Network interface configuration:
auto lo
iface lo inet loopback
auto eth0
allow-hotplug eth0
iface eth0 inet static
pre-up /sbin/ethtool -K eth0 rx off
post-up /sbin/ethtool -K eth0 rx off
address 192.168.2.120
netmask 255.255.255.0
network 192.168.2.0
broadcast 192.168.2.255
gateway 192.168.2.1
dns-nameservers 200.91.75.6 200.91.75.5 192.168.2.1
dns-search local
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UP qlen 1000
link/ether 00:23:9e:00:0f:62 brd ff:ff:ff:ff:ff:ff
inet 192.168.2.120/24 brd 192.168.2.255 scope global eth0
inet6 fe80::223:9eff:fe00:f62/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed
multicast|bytes packets errs drop fifo colls carrier compressed
lo: 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0
eth0: 881076 1518 0 0 0 0 0 0
304557 1691 0 0 0 0 0 0
*** Protocol statistics:
Ip:
1474 total packets received
0 forwarded
0 incoming packets discarded
1474 incoming packets delivered
1641 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
61 active connections openings
0 passive connection openings
0 failed connection attempts
7 connection resets received
3 connections established
1276 segments received
1438 segments send out
0 segments retransmited
0 bad segments received.
23 resets sent
Udp:
186 packets received
0 packets to unknown port received.
0 packet receive errors
203 packets sent
UdpLite:
TcpExt:
36 TCP sockets finished time wait in fast timer
28 delayed acks sent
1 packets directly queued to recvmsg prequeue.
1 bytes directly received in process context from prequeue
839 packet headers predicted
132 acknowledgments not containing data payload received
71 predicted acknowledgments
4 connections reset due to unexpected data
7 connections reset due to early user close
TCPSackShiftFallback: 1
IpExt:
InMcastPkts: 12
InOctets: 857488
OutOctets: 278739
InMcastOctets: 384
*** Device features:
eth0: 0x4180
lo: 0xa01b7c65
** PCI devices:
00:06.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8169/8110 Family
PCI Gigabit Ethernet NIC [10ec:8169]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr+ Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 36
Region 0: I/O ports at 4000 [size=256]
Region 1: Memory at 50072000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 50040000 [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
00:08.0 VGA compatible controller [0300]: Silicon Integrated Systems
[SiS] 315PRO PCI/AGP VGA Display Adapter [1039:0325] (prog-if 00 [VGA
controller])
Subsystem: Device [3030:3030]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 71 (750ns min, 4000ns max)
Interrupt: pin A routed to IRQ 38
BIST result: 00
Region 0: Memory at 40000000 (32-bit, prefetchable) [size=256M]
Region 1: Memory at 50000000 (32-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 4800 [size=128]
Expansion ROM at 50060000 [size=64K]
Capabilities: <access denied>
Kernel driver in use: sisfb
00:0e.0 ISA bridge [0601]: Advanced Micro Devices [AMD] CS5536 [Geode
companion] ISA [1022:2090] (rev 03)
Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
companion] ISA [1022:2090]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 4cf0 [size=8]
Region 1: I/O ports at 4400 [size=256]
Region 2: I/O ports at 4c80 [size=64]
Region 4: I/O ports at 4880 [size=128]
Region 5: I/O ports at 4cc0 [size=32]
00:0e.2 IDE interface [0101]: Advanced Micro Devices [AMD] CS5536
[Geode companion] IDE [1022:209a] (rev 01) (prog-if 80 [Master])
Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
companion] IDE [1022:209a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 14
Region 0: [virtual] Memory at 000001f0 (32-bit,
non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3,
non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit,
non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3,
non-prefetchable) [size=1]
Region 4: I/O ports at 4ce0 [size=16]
Kernel driver in use: pata_amd
00:0e.3 Multimedia audio controller [0401]: Advanced Micro Devices
[AMD] CS5536 [Geode companion] Audio [1022:2093] (rev 01)
Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
companion] Audio [1022:2093]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 4c00 [size=128]
Kernel driver in use: cs5535audio
00:0e.4 USB Controller [0c03]: Advanced Micro Devices [AMD] CS5536
[Geode companion] OHC [1022:2094] (rev 02) (prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
companion] OHC [1022:2094]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 50070000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:0e.5 USB Controller [0c03]: Advanced Micro Devices [AMD] CS5536
[Geode companion] EHC [1022:2095] (rev 02) (prog-if 20 [EHCI])
Subsystem: Advanced Micro Devices [AMD] CS5536 [Geode
companion] EHC [1022:2095]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 50071000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ehci_hcd
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 04d9:1702 Holtek Semiconductor, Inc.
Bus 002 Device 003: ID 0458:003a KYE Systems Corp. (Mouse Systems)
NetScroll+ Mini Traveler / Genius NetScroll 120
-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: mipsel (mips64)
Kernel: Linux 3.0.0-1-loongson-2f
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.0.0-1-loongson-2f depends on:
ii debconf [debconf-2.0] 1.5.41 Debian configuration management sy
ii linux-base 3.3 Linux image base package
ii module-init-tools 3.16-1 tools for managing Linux kernel mo
Versions of packages linux-image-3.0.0-1-loongson-2f recommends:
ii firmware-linux-free 3 Binary firmware for various driver
Versions of packages linux-image-3.0.0-1-loongson-2f suggests:
pn linux-doc-3.0.0 <none> (no description available)
Versions of packages linux-image-3.0.0-1-loongson-2f is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.33 Binary firmware for various driver
ii firmware-linux-nonfree 0.33 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-3.0.0-1-loongson-2f/prerm/removing-running-kernel-3.0.0-1-loongson-2f:
true
linux-image-3.0.0-1-loongson-2f/postinst/missing-firmware-3.0.0-1-loongson-2f:
linux-image-3.0.0-1-loongson-2f/postinst/depmod-error-initrd-3.0.0-1-loongson-2f:
false
linux-image-3.0.0-1-loongson-2f/postinst/ignoring-ramdisk:
Reply to: