Bug#636092: linux-image-2.6.32-5-amd64: Debian squeeze will not boot with drives on two Sil 3132 SATA cards
Package: linux-2.6
Version: 2.6.32-35
Severity: grave
Justification: renders package unusable
I'm trying to build a home NAS server with Debian Squeeze (6.0.2) on a homebrew amd64 system. The machine has a total of 6 hard disks in it: two 160GB Hitachi SATA for root and swap; four 1.5TB Seagate SATA that will be used for the data storage. I have two Rosewill RC-211 (based on Sil3132) 2-port SATA cards in addition to the on-board SATA ports. I have flashed both cards with the non-RAID BIOS as I intend to use software RAID only. My plan is to connect the hard disks as follows: one Hitachi and one Seagate on the motherboard SATA ports, one Hitachi and one Seagate on RC-211 card A, and the last two Seagates on RC-211 card B.
When I started out, I had only the two Hitachi drives connected, one to an internal motherboard port and the other to one of the RC-211 cards. I had no trouble installing Squeeze from a CD. The two Hitachi drives are mirrored (raid1). mdadm reports that /dev/md0 has two identical members (/dev/sda1 and /dev/sdb1) and all is well. /dev/md0 is used as a physical volume in an LVM group (rootvg) which then has two logical volumes within (8GB for swap and the rest for root). The system boots and runs just fine with only the two Hitachi disks connected.
Then I tried connecting up the four Seagate drives. The machine starts to boot and just freezes up right after "Welcome to GRUB!" I played around with several different combinations and found that the machine will boot successfully if there are drives connected only to the motherboard and/or one RC-211 card. Any scenario with drives connected to both RC-211 cards, I get the freeze right after "Welcome to GRUB!"
However, I can boot the machine from the Squeeze CD and go into rescue mode with all six drives connected. I can assemble my root mirror and mount my root filesystem successfully. Linux sees all six drives as sda through sdf.
So it would appear that there is some conflict between the two RC-211 SATA cards during a normal boot. Perhaps they're both trying to use the same address range?
For the moment, I have moved the Seagate drives off the second RC-211 card to SATA ports on the motherboard. The machine will boot and run this way with all six drives. The second card is still in the machine and does not interfere with booting as long as there are no drives connected to it.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-35) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Tue Jun 14 09:42:28 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64 root=/dev/mapper/rootvg-root ro edd=off
** Not tainted
** Kernel log:
[ 17.757159] powernow-k8: 0 : pstate 0 (3300 MHz)
[ 17.757160] powernow-k8: 1 : pstate 1 (2600 MHz)
[ 17.757161] powernow-k8: 2 : pstate 2 (2200 MHz)
[ 17.757162] powernow-k8: 3 : pstate 3 (800 MHz)
[ 26.127794] CPU0 attaching NULL sched-domain.
[ 26.127798] CPU1 attaching NULL sched-domain.
[ 26.144103] CPU0 attaching sched-domain:
[ 26.144108] domain 0: span 0-1 level MC
[ 26.144110] groups: 0 1
[ 26.144115] CPU1 attaching sched-domain:
[ 26.144116] domain 0: span 0-1 level MC
[ 26.144118] groups: 1 0
[ 26.316262] eth0: no IPv6 routers present
[ 107.496076] usb 1-2: new high speed USB device using ehci_hcd and address 4
[ 107.645034] usb 1-2: New USB device found, idVendor=0bc2, idProduct=2000
[ 107.645044] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 107.645050] usb 1-2: Product: FreeAgent Go
[ 107.645055] usb 1-2: Manufacturer: Seagate
[ 107.645059] usb 1-2: SerialNumber: 5MA0TNB0
[ 107.645249] usb 1-2: configuration #1 chosen from 1 choice
[ 107.732335] Initializing USB Mass Storage driver...
[ 107.732539] scsi12 : SCSI emulation for USB Mass Storage devices
[ 107.732594] usbcore: registered new interface driver usb-storage
[ 107.732596] USB Mass Storage support registered.
[ 107.732705] usb-storage: device found at 4
[ 107.732706] usb-storage: waiting for device to settle before scanning
[ 112.733842] usb-storage: device scan complete
[ 112.735268] scsi 12:0:0:0: Direct-Access Seagate FreeAgent Go 100F PQ: 0 ANSI: 4
[ 112.736801] sd 12:0:0:0: Attached scsi generic sg8 type 0
[ 112.740490] sd 12:0:0:0: [sdg] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 112.741994] sd 12:0:0:0: [sdg] Write Protect is off
[ 112.742004] sd 12:0:0:0: [sdg] Mode Sense: 1c 00 00 00
[ 112.742009] sd 12:0:0:0: [sdg] Assuming drive cache: write through
[ 112.745740] sd 12:0:0:0: [sdg] Assuming drive cache: write through
[ 112.745750] sdg: sdg1
[ 112.764867] sd 12:0:0:0: [sdg] Assuming drive cache: write through
[ 112.764877] sd 12:0:0:0: [sdg] Attached SCSI disk
[ 282.701860] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 282.704059] SGI XFS Quota Management subsystem
[ 282.717184] JFS: nTxBlock = 8192, nTxLock = 65536
[ 282.808894] NTFS driver 2.1.29 [Flags: R/W MODULE].
[ 282.867264] QNX4 filesystem 0.2.3 registered.
[ 282.971609] Btrfs loaded
[ 1663.698574] md: bind<sda1>
[ 1663.711804] md: bind<sde1>
[ 1663.726195] raid1: md1 is not clean -- starting background reconstruction
[ 1663.726198] raid1: raid set md1 active with 2 out of 2 mirrors
[ 1663.726215] md1: detected capacity change from 0 to 1500298077184
[ 1663.726328] md1: unknown partition table
[ 1743.040743] md: bind<sdd1>
[ 1743.041663] md: bind<sdf1>
[ 1743.044690] raid1: md2 is not clean -- starting background reconstruction
[ 1743.044699] raid1: raid set md2 active with 2 out of 2 mirrors
[ 1743.044749] md2: detected capacity change from 0 to 1500298077184
[ 1743.045374] md2: unknown partition table
[ 2461.235610] ufs_read_super: can't grok fs_clean 0xfffffffd
[12301.859639] md: resync of RAID array md1
[12301.859671] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[12301.859677] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[12301.859690] md: using 128k window, over a total of 1465134841 blocks.
[12304.786172] md: resync of RAID array md2
[12304.786180] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[12304.786186] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[12304.786196] md: using 128k window, over a total of 1465134841 blocks.
[14324.068021] CE: hpet increasing min_delta_ns to 15000 nsec
[16177.890853] EXT4-fs (dm-2): mounted filesystem with ordered data mode
[32555.832975] md: md1: resync done.
[32555.948177] RAID1 conf printout:
[32555.948185] --- wd:2 rd:2
[32555.948192] disk 0, wo:0, o:1, dev:sda1
[32555.948198] disk 1, wo:0, o:1, dev:sde1
[35518.887459] md: md2: resync done.
[35519.016001] RAID1 conf printout:
[35519.016009] --- wd:2 rd:2
[35519.016016] disk 0, wo:0, o:1, dev:sdd1
[35519.016022] disk 1, wo:0, o:1, dev:sdf1
[59839.929609] usb 1-2: USB disconnect, address 4
[67232.923524] RPC: Registered udp transport module.
[67232.923527] RPC: Registered tcp transport module.
[67232.923529] RPC: Registered tcp NFSv4.1 backchannel transport module.
[67233.327256] Bluetooth: Core ver 2.15
[67233.327346] NET: Registered protocol family 31
[67233.327350] Bluetooth: HCI device and connection manager initialized
[67233.327357] Bluetooth: HCI socket layer initialized
[67233.390735] Bluetooth: L2CAP ver 2.14
[67233.390742] Bluetooth: L2CAP socket layer initialized
[67233.542317] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[67233.717724] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[67233.717733] Bluetooth: BNEP filters: protocol multicast
[67233.766957] Bluetooth: RFCOMM TTY layer initialized
[67233.766968] Bluetooth: RFCOMM socket layer initialized
[67233.766973] Bluetooth: RFCOMM ver 1.11
[67233.823313] Bridge firewalling registered
[67234.272041] svc: failed to register lockdv1 RPC service (errno 97).
[67234.274088] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[67234.321939] Bluetooth: SCO (Voice Link) ver 0.6
[67234.321946] Bluetooth: SCO socket layer initialized
[67234.340806] NFSD: starting 90-second grace period
[76496.524296] device eth0 entered promiscuous mode
[76574.532067] device eth0 left promiscuous mode
** Model information
sys_vendor: Gigabyte Technology Co., Ltd.
product_name: GA-MA785GM-US2H
product_version:
chassis_vendor: Gigabyte Technology Co., Ltd.
chassis_version:
bios_vendor: Award Software International, Inc.
bios_version: F12a
board_vendor: Gigabyte Technology Co., Ltd.
board_name: GA-MA785GM-US2H
board_version: x.x
** Loaded modules:
Module Size Used by
sco 7225 2
bridge 39630 0
rfcomm 29613 0
stp 1440 1 bridge
bnep 9427 2
nfsd 254782 11
l2cap 24736 6 rfcomm,bnep
bluetooth 41827 6 sco,rfcomm,bnep,l2cap
lockd 57603 1 nfsd
rfkill 13044 3 bluetooth
nfs_acl 2031 1 nfsd
auth_rpcgss 33476 1 nfsd
sunrpc 161541 10 nfsd,lockd,nfs_acl,auth_rpcgss
btrfs 375805 0
zlib_deflate 17746 1 btrfs
crc32c 2560 1
libcrc32c 1074 1 btrfs
ufs 56474 0
qnx4 6194 0
hfsplus 65286 0
hfs 37455 0
minix 21197 0
ntfs 162796 0
vfat 7884 0
msdos 6202 0
fat 40038 2 vfat,msdos
jfs 140089 0
xfs 435415 0
exportfs 3170 2 nfsd,xfs
reiserfs 194156 0
ext3 106630 0
jbd 37085 1 ext3
ext2 52905 0
usb_storage 39961 0
powernow_k8 10978 0
ppdev 5030 0
lp 7462 0
cpufreq_powersave 902 0
cpufreq_conservative 5162 0
cpufreq_userspace 1992 0
cpufreq_stats 2659 0
binfmt_misc 6431 1
fuse 50892 1
loop 11799 0
firewire_sbp2 11514 0
snd_hda_codec_atihdmi 2251 1
radeon 574844 2
ttm 40146 1 radeon
snd_hda_codec_realtek 235602 1
drm_kms_helper 20369 1 radeon
drm 142327 4 radeon,ttm,drm_kms_helper
i2c_piix4 8328 0
i2c_algo_bit 4225 1 radeon
i2c_core 15819 5 radeon,drm_kms_helper,drm,i2c_piix4,i2c_algo_bit
k10temp 2715 0
edac_core 29261 0
edac_mce_amd 6433 0
snd_hda_intel 20035 1
snd_hda_codec 54244 3 snd_hda_codec_atihdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep 5380 1 snd_hda_codec
evdev 7352 8
snd_pcm 60503 2 snd_hda_intel,snd_hda_codec
snd_seq 42881 0
snd_timer 15582 2 snd_pcm,snd_seq
snd_seq_device 4493 1 snd_seq
snd 46526 10 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 4598 1 snd
snd_page_alloc 6249 2 snd_hda_intel,snd_pcm
shpchp 26264 0
pci_hotplug 21203 1 shpchp
parport_pc 18855 1
parport 27954 3 ppdev,lp,parport_pc
pcspkr 1699 0
serio_raw 3752 0
processor 29935 1 powernow_k8
button 4650 0
ext4 288318 2
mbcache 5050 3 ext3,ext2,ext4
jbd2 67015 1 ext4
crc16 1319 2 l2cap,ext4
dm_mod 53706 9
raid1 18431 3
md_mod 73872 4 raid1
sg 24069 0
sr_mod 12602 0
cdrom 29415 1 sr_mod
ata_generic 3239 0
sd_mod 29921 12
crc_t10dif 1276 1 sd_mod
usbhid 33292 0
hid 63257 1 usbhid
ohci_hcd 19343 0
ahci 32534 4
firewire_ohci 19676 0
firewire_core 36848 2 firewire_sbp2,firewire_ohci
crc_itu_t 1307 1 firewire_core
sata_sil24 11185 2
r8169 29279 0
mii 3210 1 r8169
thermal 11674 0
pata_atiixp 3489 0
thermal_sys 11942 2 processor,thermal
ehci_hcd 32081 0
libata 133760 4 ata_generic,ahci,sata_sil24,pata_atiixp
usbcore 122498 5 usb_storage,usbhid,ohci_hcd,ehci_hcd
nls_base 6377 7 hfsplus,hfs,ntfs,vfat,fat,jfs,usbcore
scsi_mod 126517 6 usb_storage,firewire_sbp2,sg,sr_mod,sd_mod,libata
** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS880 Host Bridge [1022:9601]
Subsystem: Advanced Micro Devices [AMD] RS880 Host Bridge [1022:9601]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
Region 3: Memory at <ignored> (64-bit, non-prefetchable)
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) [1022:9602] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fd900000-fdafffff
Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:02.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0) [1022:9603] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fd600000-fd6fffff
Prefetchable memory behind bridge: 00000000fdf00000-00000000fdffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) [1022:9604] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fde00000-fdefffff
Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0a.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 5) [1022:9609] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] [1002:4391] (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3c)
Subsystem: Giga-byte Technology Device [1458:4385]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Device [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fa00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_atiixp
00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
Subsystem: Giga-byte Technology Device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
Subsystem: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fd800000-fd8fffff
Prefetchable memory behind bridge: fd700000-fd7fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k10temp
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS880 [Radeon HD 4200] [1002:9710] (prog-if 00 [VGA controller])
Subsystem: Giga-byte Technology Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at ce00 [size=256]
Region 2: Memory at fdae0000 (32-bit, non-prefetchable) [size=64K]
Region 5: Memory at fd900000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: radeon
01:05.1 Audio device [0403]: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200] [1002:970f]
Subsystem: Giga-byte Technology Device [1458:960f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fdafc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
02:00.0 SATA controller [0106]: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller [1095:3132] (rev 01) (prog-if 00 [Vendor specific])
Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller [1095:3132]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fd6ff000 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fd6f8000 (64-bit, non-prefetchable) [size=16K]
Region 4: I/O ports at bf00 [size=128]
[virtual] Expansion ROM at fdf00000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil24
03:00.0 SATA controller [0106]: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller [1095:3132] (rev 01) (prog-if 00 [Vendor specific])
Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller [1095:3132]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fdeff000 (64-bit, non-prefetchable) [size=128]
Region 2: Memory at fdef8000 (64-bit, non-prefetchable) [size=16K]
Region 4: I/O ports at ef00 [size=128]
[virtual] Expansion ROM at fdd00000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil24
04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 27
Region 0: I/O ports at de00 [size=256]
Region 2: Memory at fdbff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fdbe0000 (64-bit, prefetchable) [size=64K]
[virtual] Expansion ROM at fdb00000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
05:0e.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10 [OHCI])
Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fd8ff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fd8f8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
** USB devices:
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 09eb:0131 IM Networks, Inc.
Bus 001 Device 002: ID 058f:6254 Alcor Micro Corp. USB Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.2
APT prefers stable
APT policy: (990, 'stable'), (500, 'stable-updates'), (450, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-35 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64: false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64: true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
Reply to: