Bug#632231: linux-image-3.0.0-rc5-amd64: B43 module do not work properly when I turn WiFi on after reboot
Package: linux-2.6
Version: 3.0.0~rc5-1~experimental.1
Severity: important
I have a Dell inspiron 6400. I can turn WiFi on and off with Fn + F3 switch.
WiFi is Broadcom BCM4311 cab installed with B43 module. It needs a firmware to
work properly.
Problem is:
* When the WiFi is off and I boot my linux, I cannot use my wifi. When I turn
it on, it turns on and automatically turns off again. This happen fast even
WiFi LED do not turn on.
* When the WiFi is off on I boot my linux, WiFi works properly until I turn it
off. If I turn it off, it would be impossible to turn it on again.
I was thinking this is the problem of firmware. At first, I reported a bug for
this package (Bug#632004). But after some conversations the maintainers of the
firmware package told me it seems this is not the problem of the firmware
because it loads when I boot the laptop with WiFi on.
I did not have such problem with 2.6.32 kernel. It works properly in that
kernel. But in kernels after that this problem exist (ex. 2.6.39-2-amd64). It
seems there should be a bug in the kernel.
These are some information you may need:
# dmesg | grep b43
[ 2.134860] b43-pci-bridge 0000:0b:00.0: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[ 2.134870] b43-pci-bridge 0000:0b:00.0: setting latency timer to 64
[ 6.739795] b43-phy0: Broadcom 4311 WLAN found (core revision 10)
[ 6.843324] Registered led device: b43-phy0::tx
[ 6.843346] Registered led device: b43-phy0::rx
[ 6.843369] Registered led device: b43-phy0::radio
[ 16.732151] b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
[ 101.844084] b43-phy0: Radio hardware status changed to DISABLED
#lspci -vnn | grep 14e4
03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX
[14e4:170c] (rev 02)
0b:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN
[14e4:4311] (rev 01)
# inxi -N
Network: Card-1 Broadcom BCM4401-B0 100Base-TX driver b44
Card-2 Broadcom BCM4311 802.11b/g WLAN driver b43-pci-bridge
# dpkg -l | grep b43
ii b43-fwcutter 1:014-4
Utility for extracting Broadcom 43xx firmware
ii firmware-b43-installer 1:014-4
Installer package for firmware for the b43 driver
#ifconfig
eth1 Link encap:Ethernet HWaddr 00:15:c5:ca:1b:e5
inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::215:c5ff:feca:1be5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4027 errors:0 dropped:0 overruns:0 frame:0
TX packets:3834 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:4119437 (3.9 MiB) TX bytes:516841 (504.7 KiB)
Interrupt:17
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1584 (1.5 KiB) TX bytes:1584 (1.5 KiB)
-- Package-specific info:
** Version:
Linux version 3.0.0-rc5-amd64 (Debian 3.0.0~rc5-1~experimental.1) (maks@debian.org) (gcc version 4.4.6 (Debian 4.4.6-6) ) #1 SMP Tue Jun 28 10:21:15 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.0.0-rc5-amd64 root=UUID=9dc60fb7-3920-4414-b8ee-c55127d4bf97 ro quiet
** Not tainted
** Kernel log:
[ 10.810976] fuse init (API version 7.16)
[ 14.757197] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 14.757200] Bluetooth: BNEP filters: protocol multicast
[ 14.757323] Bluetooth: RFCOMM TTY layer initialized
[ 14.757328] Bluetooth: RFCOMM socket layer initialized
[ 14.757330] Bluetooth: RFCOMM ver 1.11
[ 16.446468] lp: driver loaded but no devices found
[ 16.488850] ppdev: user-space parallel port driver
[ 16.732151] b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
[ 16.805626] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 16.812246] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.816209] b44 ssb1:0: eth1: Link is up at 100 Mbps, full duplex
[ 19.816217] b44 ssb1:0: eth1: Flow control is off for TX and off for RX
[ 19.817559] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 30.712037] eth1: no IPv6 routers present
[ 36.928344] CE: hpet increased min_delta_ns to 20113 nsec
[ 37.133056] CE: hpet increased min_delta_ns to 30169 nsec
[ 99.906310] keyboard: can't emulate rawmode for keycode 240
[ 99.906330] keyboard: can't emulate rawmode for keycode 240
[ 101.844084] b43-phy0: Radio hardware status changed to DISABLED
[ 102.576152] usb 5-2: USB disconnect, device number 3
[ 102.576158] usb 5-2.1: USB disconnect, device number 4
[ 102.576960] btusb_intr_complete: hci0 urb ffff8800c9c3b780 failed to resubmit (19)
[ 102.576974] btusb_bulk_complete: hci0 urb ffff8800c9c3b600 failed to resubmit (19)
[ 102.577961] btusb_bulk_complete: hci0 urb ffff8800c9c3b6c0 failed to resubmit (19)
[ 102.578001] btusb_send_frame: hci0 urb ffff8800c9c3b6c0 submission failed
[ 102.828664] usb 5-2.2: USB disconnect, device number 5
[ 102.884194] usb 5-2.3: USB disconnect, device number 6
[ 105.884350] keyboard: can't emulate rawmode for keycode 240
[ 105.884369] keyboard: can't emulate rawmode for keycode 240
[ 106.288031] usb 5-2: new full speed USB device number 7 using uhci_hcd
[ 106.467995] usb 5-2: New USB device found, idVendor=0a5c, idProduct=4500
[ 106.467999] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 106.468015] usb 5-2: Product: BCM2045B2
[ 106.468017] usb 5-2: Manufacturer: Broadcom
[ 106.471064] hub 5-2:1.0: USB hub found
[ 106.472983] hub 5-2:1.0: 3 ports detected
[ 106.754010] usb 5-2.1: new full speed USB device number 8 using uhci_hcd
[ 106.883995] usb 5-2.1: New USB device found, idVendor=413c, idProduct=8126
[ 106.884002] usb 5-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 106.884024] usb 5-2.1: Product: BCM2045
[ 106.884029] usb 5-2.1: Manufacturer: Broadcom Corp
[ 106.965028] usb 5-2.2: new full speed USB device number 9 using uhci_hcd
[ 107.099012] usb 5-2.2: New USB device found, idVendor=0a5c, idProduct=4502
[ 107.099019] usb 5-2.2: New USB device strings: Mfr=1, Product=0, SerialNumber=0
[ 107.099024] usb 5-2.2: Manufacturer: Broadcom Corp
[ 107.105490] input: Broadcom Corp as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2.2/5-2.2:1.0/input/input14
[ 107.105666] generic-usb 0003:0A5C:4502.0005: input,hidraw2: USB HID v1.11 Keyboard [Broadcom Corp] on usb-0000:00:1d.3-2.2/input0
[ 107.177011] usb 5-2.3: new full speed USB device number 10 using uhci_hcd
[ 107.311016] usb 5-2.3: New USB device found, idVendor=0a5c, idProduct=4503
[ 107.311024] usb 5-2.3: New USB device strings: Mfr=1, Product=0, SerialNumber=0
[ 107.311029] usb 5-2.3: Manufacturer: Broadcom Corp
[ 107.319604] input: Broadcom Corp as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2.3/5-2.3:1.0/input/input15
[ 107.319840] generic-usb 0003:0A5C:4503.0006: input,hidraw3: USB HID v1.11 Mouse [Broadcom Corp] on usb-0000:00:1d.3-2.3/input0
[ 109.520104] usb 5-2: USB disconnect, device number 7
[ 109.520111] usb 5-2.1: USB disconnect, device number 8
[ 109.521004] btusb_intr_complete: hci0 urb ffff8800b8830440 failed to resubmit (19)
[ 109.521017] btusb_bulk_complete: hci0 urb ffff8800b8830380 failed to resubmit (19)
[ 109.522006] btusb_bulk_complete: hci0 urb ffff8800b88302c0 failed to resubmit (19)
[ 109.522045] btusb_send_frame: hci0 urb ffff8800b88302c0 submission failed
[ 109.772694] usb 5-2.2: USB disconnect, device number 9
[ 109.820246] usb 5-2.3: USB disconnect, device number 10
[ 111.676921] keyboard: can't emulate rawmode for keycode 240
[ 111.676939] keyboard: can't emulate rawmode for keycode 240
[ 147.715923] keyboard: can't emulate rawmode for keycode 240
[ 147.715944] keyboard: can't emulate rawmode for keycode 240
[ 148.200066] usb 5-2: new full speed USB device number 11 using uhci_hcd
[ 148.374359] usb 5-2: New USB device found, idVendor=0a5c, idProduct=4500
[ 148.374363] usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 148.374366] usb 5-2: Product: BCM2045B2
[ 148.374368] usb 5-2: Manufacturer: Broadcom
[ 148.377419] hub 5-2:1.0: USB hub found
[ 148.379347] hub 5-2:1.0: 3 ports detected
[ 148.661375] usb 5-2.1: new full speed USB device number 12 using uhci_hcd
[ 148.789367] usb 5-2.1: New USB device found, idVendor=413c, idProduct=8126
[ 148.789375] usb 5-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 148.789380] usb 5-2.1: Product: BCM2045
[ 148.789384] usb 5-2.1: Manufacturer: Broadcom Corp
[ 148.864357] usb 5-2.2: new full speed USB device number 13 using uhci_hcd
[ 148.998352] usb 5-2.2: New USB device found, idVendor=0a5c, idProduct=4502
[ 148.998356] usb 5-2.2: New USB device strings: Mfr=1, Product=0, SerialNumber=0
[ 148.998358] usb 5-2.2: Manufacturer: Broadcom Corp
[ 149.004800] input: Broadcom Corp as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2.2/5-2.2:1.0/input/input16
[ 149.004900] generic-usb 0003:0A5C:4502.0007: input,hidraw2: USB HID v1.11 Keyboard [Broadcom Corp] on usb-0000:00:1d.3-2.2/input0
[ 149.076784] usb 5-2.3: new full speed USB device number 14 using uhci_hcd
[ 149.212360] usb 5-2.3: New USB device found, idVendor=0a5c, idProduct=4503
[ 149.212364] usb 5-2.3: New USB device strings: Mfr=1, Product=0, SerialNumber=0
[ 149.212366] usb 5-2.3: Manufacturer: Broadcom Corp
[ 149.220691] input: Broadcom Corp as /devices/pci0000:00/0000:00:1d.3/usb5/5-2/5-2.3/5-2.3:1.0/input/input17
[ 149.220828] generic-usb 0003:0A5C:4503.0008: input,hidraw3: USB HID v1.11 Mouse [Broadcom Corp] on usb-0000:00:1d.3-2.3/input0
[ 151.432097] usb 5-2: USB disconnect, device number 11
[ 151.432104] usb 5-2.1: USB disconnect, device number 12
[ 151.432377] btusb_intr_complete: hci0 urb ffff8800c9524840 failed to resubmit (19)
[ 151.432393] btusb_bulk_complete: hci0 urb ffff8800c95246c0 failed to resubmit (19)
[ 151.433377] btusb_bulk_complete: hci0 urb ffff8800c9524780 failed to resubmit (19)
[ 151.433419] btusb_send_frame: hci0 urb ffff8800c9524780 submission failed
[ 151.686311] usb 5-2.2: USB disconnect, device number 13
[ 151.736238] usb 5-2.3: USB disconnect, device number 14
[ 424.960978] NMI: PCI system error (SERR) for reason a1 on CPU 0.
[ 424.960982] Dazed and confused, but trying to continue
** Model information
sys_vendor: Dell Inc.
product_name: MM061
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: A17
board_vendor: Dell Inc.
board_name: 0XD720
board_version:
** Loaded modules:
Module Size Used by
parport_pc 22191 0
ppdev 12725 0
lp 17190 0
parport 31650 3 parport_pc,ppdev,lp
bnep 17424 2
rfcomm 32745 0
cpufreq_stats 12762 0
cpufreq_powersave 12454 0
acpi_cpufreq 12849 1
mperf 12411 1 acpi_cpufreq
cpufreq_conservative 13147 0
cpufreq_userspace 12576 0
binfmt_misc 12914 1
fuse 61507 3
loop 22479 0
snd_hda_codec_idt 53325 1
snd_hda_intel 25946 2
snd_hda_codec 67865 2 snd_hda_codec_idt,snd_hda_intel
snd_hwdep 13148 1 snd_hda_codec
snd_pcm_oss 40662 0
snd_mixer_oss 17905 1 snd_pcm_oss
snd_pcm 67276 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_midi 12848 0
snd_rawmidi 22963 1 snd_seq_midi
snd_seq_midi_event 13316 1 snd_seq_midi
snd_seq 44678 2 snd_seq_midi,snd_seq_midi_event
snd_timer 22658 2 snd_pcm,snd_seq
snd_seq_device 13155 3 snd_seq_midi,snd_rawmidi,snd_seq
btusb 17417 0
radeon 743531 2
ttm 52224 1 radeon
snd 52406 15 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
bluetooth 112546 11 bnep,rfcomm,btusb
drm_kms_helper 26950 1 radeon
arc4 12458 2
r852 17768 0
sm_common 16450 1 r852
nand 44305 2 r852,sm_common
nand_ids 12313 1 nand
nand_ecc 12444 1 nand
soundcore 13014 1 snd
snd_page_alloc 12969 2 snd_hda_intel,snd_pcm
b43 292695 0
r592 17576 0
drm 166656 4 radeon,ttm,drm_kms_helper
dell_laptop 12852 0
dell_wmi 12477 0
mac80211 181749 1 b43
cfg80211 131541 2 b43,mac80211
rfkill 18970 5 bluetooth,dell_laptop,cfg80211
rng_core 12614 1 b43
i2c_algo_bit 12834 1 radeon
mtd 24200 2 sm_common,nand
memstick 13726 1 r592
joydev 17138 0
dcdbas 13256 1 dell_laptop
sparse_keymap 12760 1 dell_wmi
video 17553 0
ac 12624 0
i2c_i801 16870 0
i2c_core 23766 5 radeon,drm_kms_helper,drm,i2c_algo_bit,i2c_i801
wmi 13202 1 dell_wmi
pcspkr 12579 0
evdev 17475 24
psmouse 55241 0
serio_raw 12878 0
battery 13109 0
power_supply 13475 4 radeon,dell_laptop,ac,battery
button 12895 0
processor 27431 3 acpi_cpufreq
ext4 317588 1
mbcache 12930 1 ext4
jbd2 65052 1 ext4
crc16 12343 2 bluetooth,ext4
usbhid 39946 0
hid 76841 1 usbhid
btrfs 501720 0
zlib_deflate 25466 1 btrfs
crc32c 12656 1
libcrc32c 12426 1 btrfs
sg 25769 0
sd_mod 35644 3
sr_mod 21824 0
cdrom 35134 1 sr_mod
crc_t10dif 12348 1 sd_mod
b44 31440 0
ata_generic 12479 0
uhci_hcd 26529 0
ata_piix 25319 2
libata 151616 2 ata_generic,ata_piix
firewire_ohci 35072 0
firewire_core 47887 1 firewire_ohci
crc_itu_t 12347 1 firewire_core
thermal 17330 0
thermal_sys 17939 3 video,processor,thermal
ssb 44219 2 b43,b44
sdhci_pci 13184 0
sdhci 26052 1 sdhci_pci
pcmcia 32719 2 b43,ssb
mmc_core 63039 3 b43,ssb,sdhci
pcmcia_core 18333 1 pcmcia
mii 12675 1 b44
ehci_hcd 39487 0
scsi_mod 161602 4 sg,sr_mod,sd_mod,libata
usbcore 127203 5 btusb,usbhid,uhci_hcd,ehci_hcd
** Network interface configuration:
auto lo
iface lo inet loopback
allow-hotplug eth0
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
link/ether 00:15:c5:ca:1b:e5 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.101/24 brd 192.168.0.255 scope global eth1
inet6 fe80::215:c5ff:feca:1be5/64 scope link
valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 00:18:f3:ec:78:66 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 1584 16 0 0 0 0 0 0 1584 16 0 0 0 0 0 0
eth1: 1633198 2159 0 0 0 0 0 48 365557 2257 0 0 0 0 0 0
wlan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
2193 total packets received
2 with invalid addresses
0 forwarded
0 incoming packets discarded
2191 incoming packets delivered
2226 requests sent out
40 dropped because of missing route
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
96 active connections openings
0 passive connection openings
4 failed connection attempts
0 connection resets received
1 connections established
1766 segments received
1773 segments send out
44 segments retransmited
0 bad segments received.
47 resets sent
Udp:
443 packets received
0 packets to unknown port received.
0 packet receive errors
396 packets sent
UdpLite:
TcpExt:
43 TCP sockets finished time wait in fast timer
124 delayed acks sent
Quick ack mode was activated 44 times
14 packets directly queued to recvmsg prequeue.
9052 bytes directly received in process context from prequeue
1023 packet headers predicted
7 packets header predicted and directly queued to user
226 acknowledgments not containing data payload received
4 predicted acknowledgments
30 congestion windows recovered without slow start after partial ack
37 other TCP timeouts
41 DSACKs sent for old packets
18 DSACKs received
5 connections reset due to unexpected data
1 connections aborted due to timeout
TCPDSACKIgnoredOld: 2
TCPDSACKIgnoredNoUndo: 7
IpExt:
InMcastPkts: 50
OutMcastPkts: 32
InBcastPkts: 49
OutBcastPkts: 49
InOctets: 1593514
OutOctets: 320577
InMcastOctets: 4116
OutMcastOctets: 3636
InBcastOctets: 7036
OutBcastOctets: 7036
*** Device features:
eth1: 0x4000
lo: 0xa01b7c65
wlan0: 0x6000
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: efd00000-efefffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at efffc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: efc00000-efcfffff
Prefetchable memory behind bridge: 00000000e0200000-00000000e03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 4 [8086:27d6] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: efa00000-efbfffff
Prefetchable memory behind bridge: 00000000e0000000-00000000e01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at bf80 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at bf60 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at bf40 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 4: I/O ports at bf20 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: ef900000-ef9fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01)
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 01) (prog-if 80 [Master])
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at bfa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 01)
Subsystem: Dell Device [1028:01bd]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 10c0 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon Mobility X1400 [1002:7145] (prog-if 00 [VGA controller])
Subsystem: Dell Device [1028:2003]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at ee00 [size=256]
Region 2: Memory at efdf0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at efd00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon
03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
Subsystem: Dell Inspiron 6400 [1028:01af]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 17
Region 0: Memory at ef9fe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: b44
03:01.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832] (prog-if 10 [OHCI])
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ef9fd800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
03:01.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 19) (prog-if 01)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 18
Region 0: Memory at ef9fd400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci-pci
03:01.2 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 0a)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 18
Region 0: Memory at ef9fd600 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: r592
03:01.3 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev 05)
Subsystem: Dell Device [1028:01bd]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 18
Region 0: Memory at ef9fd700 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: r852
0b:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01)
Subsystem: Dell Wireless 1390 WLAN Mini-Card [1028:0007]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at efcfc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: b43-pci-bridge
** USB devices:
Bus 005 Device 022: ID 0a5c:4503 Broadcom Corp.
Bus 005 Device 021: ID 0a5c:4502 Broadcom Corp. Keyboard (Boot Interface Subclass)
Bus 005 Device 020: ID 413c:8126 Dell Computer Corp. Wireless 355 Bluetooth
Bus 005 Device 019: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Bus 005 Device 002: ID 09da:8090 A4 Tech Co., Ltd
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.0.0-rc5-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.utf8, LC_CTYPE=en_US.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.0.0-rc5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36 Debian configuration management sy
ii initramfs-tools [linux-initra 0.99 tools for generating an initramfs
ii linux-base 3.2 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-3.0.0-rc5-amd64 recommends:
ii firmware-linux-free 3 Binary firmware for various driver
Versions of packages linux-image-3.0.0-rc5-amd64 suggests:
ii grub-pc 1.98+20100804-8 GRand Unified Bootloader, version
pn linux-doc-3.0.0 <none> (no description available)
Versions of packages linux-image-3.0.0-rc5-amd64 is related to:
ii firmware-bnx2 0.27 Binary firmware for Broadcom NetXt
ii firmware-bnx2x 0.27 Binary firmware for Broadcom NetXt
ii firmware-ipw2x00 0.27 Binary firmware for Intel Pro Wire
ii firmware-ivtv 0.27 Binary firmware for iTVC15-family
ii firmware-iwlwifi 0.27 Binary firmware for Intel Wireless
ii firmware-linux 0.30 Binary firmware for various driver
ii firmware-linux-nonfree 0.30 Binary firmware for various driver
ii firmware-qlogic 0.27 Binary firmware for QLogic IBA7220
ii firmware-ralink 0.27 Binary firmware for Ralink wireles
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-3.0.0-rc5-amd64/postinst/depmod-error-initrd-3.0.0-rc5-amd64: false
* linux-image-3.0.0-rc5-amd64/postinst/missing-firmware-3.0.0-rc5-amd64:
linux-image-3.0.0-rc5-amd64/postinst/ignoring-ramdisk:
linux-image-3.0.0-rc5-amd64/prerm/removing-running-kernel-3.0.0-rc5-amd64: true
Reply to: