Bug#631287: BUG during access to hiddev (APC UPS)
Package: linux-image-2.6.32-5-686-bigmem
Version: 2.6.32-34squeeze1
Severity: important
After upgrading to squeeze I've started receiving the following BUG in dmesg
when apcupsd tries to access hid device for my UPS (APC SmartUPS 3000,
connected via USB).
[ 42.745031] usb 2-2: new low speed USB device using uhci_hcd and address 4
[ 42.938593] usb 2-2: New USB device found, idVendor=051d, idProduct=0002
[ 42.938599] usb 2-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 42.938603] usb 2-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:2.4
[ 42.938607] usb 2-2: Manufacturer: American Power Conversion
[ 42.938610] usb 2-2: SerialNumber: CS0533110332
[ 42.938754] usb 2-2: configuration #1 chosen from 1 choice
[ 45.380361] generic-usb 0003:051D:0002.0005: hiddev0,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:2.4] on u
sb-0000:00:1d.0-2/input0
[ 48.268044] usb 2-2: USB disconnect, address 4
[ 48.269572] /tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/hid/usbhid/hid-core.c: usb_submit_urb(ctrl) failed
[ 48.731053] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 48.731193] IP: [<f843db27>] hiddev_ioctl+0x26/0x56f [usbhid]
[ 48.731294] *pdpt = 000000003587c001 *pde = 0000000000000000
[ 48.731424] Oops: 0000 [#1] SMP
[ 48.731549] last sysfs file: /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/0003:051D:0002.0005/hidraw/hidraw0/uevent
[ 48.731619] Modules linked in: microcode xfs exportfs eeprom ipmi_devintf st(+) ch(+) ipmi_si ipmi_msghandler mptctl psmouse dm_snapshot snd_pcm snd_timer
parport_pc snd soundcore snd_page_alloc parport i2c_i801 pcspkr e752x_edac shpchp joydev evdev serio_raw container i2c_core rng_core pci_hotplug button edac_c
ore processor ext3 jbd mbcache dm_mod sr_mod cdrom sg sd_mod crc_t10dif ata_generic usbhid hid aic7xxx ata_piix uhci_hcd libata mptspi megaraid_mbox mptscsih
mptbase ehci_hcd floppy tg3 megaraid_mm scsi_transport_spi libphy thermal thermal_sys scsi_mod usbcore nls_base [last unloaded: scsi_wait_scan]
[ 48.734244]
[ 48.734295] Pid: 1390, comm: apcupsd Not tainted (2.6.32-5-686-bigmem #1) D1889
[ 48.734361] EIP: 0060:[<f843db27>] EFLAGS: 00010286 CPU: 0
[ 48.734419] EIP is at hiddev_ioctl+0x26/0x56f [usbhid]
[ 48.734473] EAX: 00000000 EBX: 400c4807 ECX: bffb50d4 EDX: fffffffb
[ 48.734528] ESI: f65dd5c0 EDI: f645a000 EBP: bffb50d4 ESP: f5f8bea0
[ 48.734584] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 48.734639] Process apcupsd (pid: 1390, ti=f5f8a000 task=f5dc1100 task.ti=f5f8a000)
[ 48.734703] Stack:
[ 48.734752] c1031658 f5b20000 c143de20 f5ff9e00 c2608e20 f5ff9e00 c127e933 c13a4ba0
[ 48.735023] <0> c143959c c143de20 c143de20 c1439354 f5dc12bc c2608e20 00000000 00000000
[ 48.735023] <0> 00000296 00000292 0000c350 f5dc1100 c26045cc f5f8bf44 c104d131 f5f8bf44
[ 48.735023] Call Trace:
[ 48.735023] [<c1031658>] ? finish_task_switch+0x34/0x95
[ 48.735023] [<c127e933>] ? schedule+0x7a4/0x7f1
[ 48.735023] [<c104d131>] ? lock_hrtimer_base+0x15/0x2f
[ 48.735023] [<c104d1af>] ? hrtimer_try_to_cancel+0x2f/0x35
[ 48.735023] [<c104d1bf>] ? hrtimer_cancel+0xa/0x14
[ 48.735023] [<f843db01>] ? hiddev_ioctl+0x0/0x56f [usbhid]
[ 48.735023] [<c10c53d4>] ? vfs_ioctl+0x1c/0x5f
[ 48.735023] [<c10c5968>] ? do_vfs_ioctl+0x4aa/0x4e5
[ 48.735023] [<c104cae6>] ? hrtimer_wakeup+0x0/0x18
[ 48.735023] [<c10517e0>] ? getnstimeofday+0x4d/0xc9
[ 48.735023] [<c1051896>] ? do_gettimeofday+0xf/0x29
[ 48.735023] [<c10c59e4>] ? sys_ioctl+0x41/0x58
[ 48.735023] [<c100813b>] ? sysenter_do_call+0x12/0x28
[ 48.735023] Code: 5b 5e 5f 5d c3 55 89 cd 57 56 53 89 d3 83 ec 7c 8b 40 70 ba fb ff ff ff 89 44 24 04 8b b0 10 c0 00 00 8b 7e 28 8b 87 54 0c 00 00 <8b> 08 8b 87 a0 0e 00 00 89 04 24 83 3e 00 0f 84 2b 05 00 00 81
[ 48.735023] EIP: [<f843db27>] hiddev_ioctl+0x26/0x56f [usbhid] SS:ESP 0068:f5f8bea0
[ 48.735023] CR2: 0000000000000000
[ 48.739373] ---[ end trace 650ff9964d1a683e ]---
Full dmesg will be attached to this message.
-- System Information:
Debian Release: wheezy/sid
APT prefers testing-proposed-updates
APT policy: (500, 'testing-proposed-updates'), (500, 'stable-updates'), (500, 'unstable'), (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.39-2-686-pae (SMP w/2 CPU cores)
Locale: LANG=ru_RU.utf8, LC_CTYPE=ru_RU.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
--
With best wishes
Dmitry
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-686-bigmem (Debian 2.6.32-34squeeze1) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed May 18 07:33:52 UTC 2011
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009a800 (usable)
[ 0.000000] BIOS-e820: 000000000009a800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007fefb000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fefb000 - 000000007ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff00000 - 000000007ff80000 (usable)
[ 0.000000] BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0x7ff80 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF80000 mask FFFF80000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01a00000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037600000 page 2M
[ 0.000000] 0037600000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ 10000-17000
[ 0.000000] RAMDISK: 376d3000 - 37fefdda
[ 0.000000] Allocated new RAMDISK: 00100000 - 00a1cdda
[ 0.000000] Move RAMDISK from 00000000376d3000 - 0000000037fefdd9 to 00100000 - 00a1cdd9
[ 0.000000] ACPI: RSDP 000f6ba0 00024 (v02 PTLTD )
[ 0.000000] ACPI: XSDT 7fef5381 0004C (v01 PTLTD ? XSDT 06040001 LTP 00000000)
[ 0.000000] ACPI: FACP 7fef5441 000F4 (v03 FSC 06040001 000F4240)
[ 0.000000] ACPI: DSDT 7fef5535 0597B (v01 FSC D1649 06040001 MSFT 02000002)
[ 0.000000] ACPI: FACS 7fefbfc0 00040
[ 0.000000] ACPI: SPCR 7fefaeb0 00050 (v01 PTLTD $UCRTBL$ 06040001 PTL 00000001)
[ 0.000000] ACPI: MCFG 7fefaf00 00040 (v01 PTLTD MCFG 06040001 LTP 00000000)
[ 0.000000] ACPI: APIC 7fefaf40 00098 (v01 PTLTD ? APIC 06040001 LTP 00000000)
[ 0.000000] ACPI: BOOT 7fefafd8 00028 (v01 PTLTD $SBFTBL$ 06040001 LTP 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1159MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] node 0 low ram: 00000000 - 377fe000
[ 0.000000] node 0 bootmap 00014000 - 0001af00
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0001000000 - 00014ff3f4] TEXT DATA BSS ==> [0001000000 - 00014ff3f4]
[ 0.000000] #4 [000009a800 - 0000100000] BIOS reserved ==> [000009a800 - 0000100000]
[ 0.000000] #5 [0001500000 - 000150d1b0] BRK ==> [0001500000 - 000150d1b0]
[ 0.000000] #6 [0000010000 - 0000014000] PGTABLE ==> [0000010000 - 0000014000]
[ 0.000000] #7 [0000100000 - 0000a1cdda] NEW RAMDISK ==> [0000100000 - 0000a1cdda]
[ 0.000000] #8 [0000014000 - 000001b000] BOOTMAP ==> [0000014000 - 000001b000]
[ 0.000000] found SMP MP-table at [c00f6c10] f6c10
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x0007ff80
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009a
[ 0.000000] 0: 0x00000100 -> 0x0007fef0
[ 0.000000] 0: 0x0007ff00 -> 0x0007ff80
[ 0.000000] On node 0 totalpages: 524026
[ 0.000000] free_area_init_node: node 0, pgdat c13d2100, node_mem_map c150f200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3946 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2320 pages used for memmap
[ 0.000000] HighMem zone: 294498 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0xf008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec80800] gsi_base[48])
[ 0.000000] IOAPIC[2]: apic_id 4, version 32, address 0xfec80800, GSI 48-71
[ 0.000000] ACPI: IOAPIC (id[0x05] address[0xfec84000] gsi_base[72])
[ 0.000000] IOAPIC[3]: apic_id 5, version 32, address 0xfec84000, GSI 72-95
[ 0.000000] ACPI: IOAPIC (id[0x06] address[0xfec84800] gsi_base[96])
[ 0.000000] IOAPIC[4]: apic_id 6, version 32, address 0xfec84800, GSI 96-119
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 120
[ 0.000000] PM: Registered nosave memory: 000000000009a000 - 000000000009b000
[ 0.000000] PM: Registered nosave memory: 000000000009b000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 15 pages/cpu @c2600000 s37688 r0 d23752 u1048576
[ 0.000000] pcpu-alloc: s37688 r0 d23752 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519930
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686-bigmem root=UUID=0e4ac9a7-9111-43ff-b284-241456b95d67 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000377fe:0007ff80)
[ 0.000000] Memory: 2063248k/2096640k available (2573k kernel code, 31884k reserved, 1378k data, 396k init, 1187272k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffa00000 (2048 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc13dc000 - 0xc143f000 ( 396 kB)
[ 0.000000] .data : 0xc128359d - 0xc13dbeb0 (1378 kB)
[ 0.000000] .text : 0xc1000000 - 0xc128359d (2573 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3000.176 MHz processor.
[ 0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 6000.35 BogoMIPS (lpj=12000704)
[ 0.004025] Security Framework initialized
[ 0.004032] SELinux: Disabled at boot.
[ 0.004041] Mount-cache hash table entries: 512
[ 0.004197] Initializing cgroup subsys ns
[ 0.004202] Initializing cgroup subsys cpuacct
[ 0.004207] Initializing cgroup subsys devices
[ 0.004210] Initializing cgroup subsys freezer
[ 0.004213] Initializing cgroup subsys net_cls
[ 0.004247] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 0.004250] CPU: L2 cache: 2048K
[ 0.004254] CPU: Physical Processor ID: 0
[ 0.004256] CPU: Processor Core ID: 0
[ 0.004260] mce: CPU supports 4 MCE banks
[ 0.004274] CPU0: Thermal monitoring enabled (TM1)
[ 0.004279] using mwait in idle threads.
[ 0.004289] Performance Events: no PMU driver, software events only.
[ 0.004298] Checking 'hlt' instruction... OK.
[ 0.021613] ACPI: Core revision 20090903
[ 0.032073] Enabling APIC mode: Flat. Using 5 I/O APICs
[ 0.032592] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.074193] CPU0: Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
[ 0.076001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.008000] Initializing CPU#1
[ 0.008000] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 0.008000] CPU: L2 cache: 2048K
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 0
[ 0.008000] CPU1: Thermal monitoring enabled (TM1)
[ 0.160120] CPU1: Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
[ 0.160131] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.164083] Brought up 2 CPUs
[ 0.164089] Total of 2 processors activated (12000.94 BogoMIPS).
[ 0.165021] CPU0 attaching sched-domain:
[ 0.165026] domain 0: span 0-1 level SIBLING
[ 0.165030] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 0.165038] domain 1: span 0-1 level MC
[ 0.165041] groups: 0-1 (cpu_power = 1178)
[ 0.165048] CPU1 attaching sched-domain:
[ 0.165050] domain 0: span 0-1 level SIBLING
[ 0.165053] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 0.165060] domain 1: span 0-1 level MC
[ 0.165063] groups: 0-1 (cpu_power = 1178)
[ 0.165168] devtmpfs: initialized
[ 0.165168] regulator: core version 0.5
[ 0.165168] NET: Registered protocol family 16
[ 0.165168] ACPI: bus type pci registered
[ 0.165168] PCI: Found Intel Corporation E7520 Memory Controller Hub with MMCONFIG support.
[ 0.165168] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.165168] PCI: MCFG area at e0000000 reserved in E820
[ 0.165168] PCI: Using MMCONFIG for extended config space
[ 0.165168] PCI: Using configuration type 1 for base access
[ 0.165168] bio: create slab <bio-0> at 0
[ 0.165168] ACPI: EC: Look up EC in DSDT
[ 0.172679] ACPI: Interpreter enabled
[ 0.172685] ACPI: (supports S0 S1 S4 S5)
[ 0.172712] ACPI: Using IOAPIC for interrupt routing
[ 0.179394] ACPI: No dock devices found.
[ 0.179511] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.179676] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[ 0.179681] pci 0000:00:02.0: PME# disabled
[ 0.179751] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 0.179756] pci 0000:00:04.0: PME# disabled
[ 0.179827] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
[ 0.179832] pci 0000:00:05.0: PME# disabled
[ 0.179907] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[ 0.179912] pci 0000:00:06.0: PME# disabled
[ 0.179985] pci 0000:00:1d.0: reg 20 io port: [0x1000-0x101f]
[ 0.180052] pci 0000:00:1d.1: reg 20 io port: [0x1400-0x141f]
[ 0.180107] pci 0000:00:1d.2: reg 20 io port: [0x1800-0x181f]
[ 0.180162] pci 0000:00:1d.3: reg 20 io port: [0x1c00-0x1c1f]
[ 0.180225] pci 0000:00:1d.7: reg 10 32bit mmio: [0xde100000-0xde1003ff]
[ 0.180285] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.180291] pci 0000:00:1d.7: PME# disabled
[ 0.180382] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.180390] pci 0000:00:1f.0: quirk: region f000-f07f claimed by ICH4 ACPI/GPIO/TCO
[ 0.180396] pci 0000:00:1f.0: quirk: region f180-f1bf claimed by ICH4 GPIO
[ 0.180421] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[ 0.180429] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[ 0.180437] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[ 0.180444] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[ 0.180452] pci 0000:00:1f.1: reg 20 io port: [0x2400-0x240f]
[ 0.180460] pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
[ 0.180515] pci 0000:00:1f.3: reg 20 io port: [0x2000-0x201f]
[ 0.180593] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.180598] pci 0000:01:00.0: PME# disabled
[ 0.180662] pci 0000:01:00.2: PME# supported from D0 D3hot D3cold
[ 0.180666] pci 0000:01:00.2: PME# disabled
[ 0.180687] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.180751] pci 0000:00:02.0: bridge io port: [0x3000-0x3fff]
[ 0.180756] pci 0000:00:02.0: bridge 32bit mmio: [0xde200000-0xde4fffff]
[ 0.180812] pci 0000:02:08.0: reg 10 io port: [0x3000-0x30ff]
[ 0.180824] pci 0000:02:08.0: reg 14 64bit mmio: [0xde210000-0xde21ffff]
[ 0.180835] pci 0000:02:08.0: reg 1c 64bit mmio: [0xde200000-0xde20ffff]
[ 0.180847] pci 0000:02:08.0: reg 30 32bit mmio pref: [0x000000-0x0fffff]
[ 0.180872] pci 0000:02:08.0: supports D1 D2
[ 0.180918] pci 0000:02:08.1: reg 10 io port: [0x3400-0x34ff]
[ 0.180930] pci 0000:02:08.1: reg 14 64bit mmio: [0xde230000-0xde23ffff]
[ 0.180941] pci 0000:02:08.1: reg 1c 64bit mmio: [0xde220000-0xde22ffff]
[ 0.180953] pci 0000:02:08.1: reg 30 32bit mmio pref: [0x000000-0x0fffff]
[ 0.180977] pci 0000:02:08.1: supports D1 D2
[ 0.181029] pci 0000:01:00.0: bridge io port: [0x3000-0x3fff]
[ 0.181034] pci 0000:01:00.0: bridge 32bit mmio: [0xde200000-0xde4fffff]
[ 0.181147] pci 0000:04:00.0: reg 10 64bit mmio: [0xde500000-0xde50ffff]
[ 0.181210] pci 0000:04:00.0: PME# supported from D3hot D3cold
[ 0.181215] pci 0000:04:00.0: PME# disabled
[ 0.181242] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.181321] pci 0000:00:04.0: bridge 32bit mmio: [0xde500000-0xde5fffff]
[ 0.181380] pci 0000:05:00.0: reg 10 64bit mmio: [0xde600000-0xde60ffff]
[ 0.181443] pci 0000:05:00.0: PME# supported from D3hot D3cold
[ 0.181449] pci 0000:05:00.0: PME# disabled
[ 0.181475] pci 0000:05:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.181555] pci 0000:00:05.0: bridge 32bit mmio: [0xde600000-0xde6fffff]
[ 0.181596] pci 0000:06:00.0: PXH quirk detected; SHPC device MSI disabled
[ 0.181608] pci 0000:06:00.0: reg 10 64bit mmio: [0xde700000-0xde700fff]
[ 0.181639] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[ 0.181643] pci 0000:06:00.0: PME# disabled
[ 0.181686] pci 0000:06:00.2: PXH quirk detected; SHPC device MSI disabled
[ 0.181722] pci 0000:06:00.2: PME# supported from D0 D3hot D3cold
[ 0.181727] pci 0000:06:00.2: PME# disabled
[ 0.181747] pci 0000:06:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.181809] pci 0000:00:06.0: bridge io port: [0x4000-0x4fff]
[ 0.181814] pci 0000:00:06.0: bridge 32bit mmio: [0xde700000-0xde8fffff]
[ 0.181821] pci 0000:00:06.0: bridge 64bit mmio pref: [0xde000000-0xde0fffff]
[ 0.181911] pci 0000:08:0b.0: reg 10 io port: [0x4000-0x40ff]
[ 0.181923] pci 0000:08:0b.0: reg 14 64bit mmio: [0xde800000-0xde800fff]
[ 0.181943] pci 0000:08:0b.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.182000] pci 0000:08:0c.0: reg 10 32bit mmio pref: [0xde000000-0xde00ffff]
[ 0.182037] pci 0000:08:0c.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.182091] pci 0000:06:00.2: bridge io port: [0x4000-0x4fff]
[ 0.182096] pci 0000:06:00.2: bridge 32bit mmio: [0xde800000-0xde8fffff]
[ 0.182103] pci 0000:06:00.2: bridge 64bit mmio pref: [0xde000000-0xde0fffff]
[ 0.182153] pci 0000:09:05.0: reg 10 32bit mmio: [0xdf000000-0xdfffffff]
[ 0.182161] pci 0000:09:05.0: reg 14 io port: [0x5000-0x50ff]
[ 0.182169] pci 0000:09:05.0: reg 18 32bit mmio: [0xde900000-0xde900fff]
[ 0.182191] pci 0000:09:05.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.182211] pci 0000:09:05.0: supports D1 D2
[ 0.182253] pci 0000:00:1e.0: transparent bridge
[ 0.182259] pci 0000:00:1e.0: bridge io port: [0x5000-0x5fff]
[ 0.182264] pci 0000:00:1e.0: bridge 32bit mmio: [0xde900000-0xdfffffff]
[ 0.182290] pci_bus 0000:00: on NUMA node 0
[ 0.182295] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.182610] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEA0.DOB0._PRT]
[ 0.182723] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEA0.DOB2._PRT]
[ 0.182970] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEC0.PXH0._PRT]
[ 0.183135] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEC0.PXH2._PRT]
[ 0.187413] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.187562] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.187707] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.187853] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 0.187977] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.188111] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.188235] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.188381] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.188529] vgaarb: device added: PCI:0000:09:05.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.188533] vgaarb: loaded
[ 0.188557] PCI: Using ACPI for IRQ routing
[ 0.188557] hpet clockevent registered
[ 0.188557] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.188557] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.188557] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.192030] Switching to clocksource tsc
[ 0.193596] pnp: PnP ACPI init
[ 0.193613] ACPI: bus type pnp registered
[ 0.196375] pnp: PnP ACPI: found 12 devices
[ 0.196378] ACPI: ACPI bus type pnp unregistered
[ 0.196384] PnPBIOS: Disabled by ACPI PNP
[ 0.196397] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.196402] system 00:02: ioport range 0xca2-0xca3 has been reserved
[ 0.196406] system 00:02: ioport range 0xca4-0xca5 has been reserved
[ 0.196413] system 00:02: ioport range 0xf000-0xf07f has been reserved
[ 0.196417] system 00:02: ioport range 0xf100-0xf10f has been reserved
[ 0.196421] system 00:02: ioport range 0xf180-0xf1bf has been reserved
[ 0.196425] system 00:02: ioport range 0x800-0x87f has been reserved
[ 0.196429] system 00:02: ioport range 0xf820-0xf82f has been reserved
[ 0.196433] system 00:02: ioport range 0xfe00-0xfe00 has been reserved
[ 0.196438] system 00:02: iomem range 0xfee00000-0xfeefffff has been reserved
[ 0.196443] system 00:02: iomem range 0xfec00000-0xfecfffff could not be reserved
[ 0.231301] pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
[ 0.231306] pci 0000:01:00.0: IO window: 0x3000-0x3fff
[ 0.231312] pci 0000:01:00.0: MEM window: 0xde200000-0xde4fffff
[ 0.231317] pci 0000:01:00.0: PREFETCH window: 0x80000000-0x801fffff
[ 0.231324] pci 0000:01:00.2: PCI bridge, secondary bus 0000:03
[ 0.231327] pci 0000:01:00.2: IO window: disabled
[ 0.231332] pci 0000:01:00.2: MEM window: disabled
[ 0.231336] pci 0000:01:00.2: PREFETCH window: disabled
[ 0.231343] pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
[ 0.231347] pci 0000:00:02.0: IO window: 0x3000-0x3fff
[ 0.231353] pci 0000:00:02.0: MEM window: 0xde200000-0xde4fffff
[ 0.231358] pci 0000:00:02.0: PREFETCH window: 0x80000000-0x801fffff
[ 0.231364] pci 0000:00:04.0: PCI bridge, secondary bus 0000:04
[ 0.231367] pci 0000:00:04.0: IO window: disabled
[ 0.231373] pci 0000:00:04.0: MEM window: 0xde500000-0xde5fffff
[ 0.231377] pci 0000:00:04.0: PREFETCH window: disabled
[ 0.231384] pci 0000:00:05.0: PCI bridge, secondary bus 0000:05
[ 0.231386] pci 0000:00:05.0: IO window: disabled
[ 0.231392] pci 0000:00:05.0: MEM window: 0xde600000-0xde6fffff
[ 0.231396] pci 0000:00:05.0: PREFETCH window: disabled
[ 0.231403] pci 0000:06:00.0: PCI bridge, secondary bus 0000:07
[ 0.231406] pci 0000:06:00.0: IO window: disabled
[ 0.231411] pci 0000:06:00.0: MEM window: disabled
[ 0.231415] pci 0000:06:00.0: PREFETCH window: disabled
[ 0.231423] pci 0000:06:00.2: PCI bridge, secondary bus 0000:08
[ 0.231427] pci 0000:06:00.2: IO window: 0x4000-0x4fff
[ 0.231432] pci 0000:06:00.2: MEM window: 0xde800000-0xde8fffff
[ 0.231438] pci 0000:06:00.2: PREFETCH window: 0x000000de000000-0x000000de0fffff
[ 0.231444] pci 0000:00:06.0: PCI bridge, secondary bus 0000:06
[ 0.231448] pci 0000:00:06.0: IO window: 0x4000-0x4fff
[ 0.231454] pci 0000:00:06.0: MEM window: 0xde700000-0xde8fffff
[ 0.231459] pci 0000:00:06.0: PREFETCH window: 0x000000de000000-0x000000de0fffff
[ 0.231467] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:09
[ 0.231471] pci 0000:00:1e.0: IO window: 0x5000-0x5fff
[ 0.231477] pci 0000:00:1e.0: MEM window: 0xde900000-0xdfffffff
[ 0.231483] pci 0000:00:1e.0: PREFETCH window: 0x80200000-0x802fffff
[ 0.231502] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.231508] pci 0000:00:02.0: setting latency timer to 64
[ 0.231520] pci 0000:01:00.0: setting latency timer to 64
[ 0.231531] pci 0000:01:00.2: setting latency timer to 64
[ 0.231542] pci 0000:00:04.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.231547] pci 0000:00:04.0: setting latency timer to 64
[ 0.231556] pci 0000:00:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.231561] pci 0000:00:05.0: setting latency timer to 64
[ 0.231570] pci 0000:00:06.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.231574] pci 0000:00:06.0: setting latency timer to 64
[ 0.231585] pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.231590] pci 0000:06:00.0: setting latency timer to 64
[ 0.231599] pci 0000:06:00.2: setting latency timer to 64
[ 0.231607] pci 0000:00:1e.0: setting latency timer to 64
[ 0.231613] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.231617] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.231621] pci_bus 0000:01: resource 0 io: [0x3000-0x3fff]
[ 0.231624] pci_bus 0000:01: resource 1 mem: [0xde200000-0xde4fffff]
[ 0.231628] pci_bus 0000:01: resource 2 pref mem [0x80000000-0x801fffff]
[ 0.231632] pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
[ 0.231635] pci_bus 0000:02: resource 1 mem: [0xde200000-0xde4fffff]
[ 0.231639] pci_bus 0000:02: resource 2 pref mem [0x80000000-0x801fffff]
[ 0.231643] pci_bus 0000:04: resource 1 mem: [0xde500000-0xde5fffff]
[ 0.231646] pci_bus 0000:05: resource 1 mem: [0xde600000-0xde6fffff]
[ 0.231650] pci_bus 0000:06: resource 0 io: [0x4000-0x4fff]
[ 0.231653] pci_bus 0000:06: resource 1 mem: [0xde700000-0xde8fffff]
[ 0.231657] pci_bus 0000:06: resource 2 pref mem [0xde000000-0xde0fffff]
[ 0.231660] pci_bus 0000:08: resource 0 io: [0x4000-0x4fff]
[ 0.231664] pci_bus 0000:08: resource 1 mem: [0xde800000-0xde8fffff]
[ 0.231681] pci_bus 0000:08: resource 2 pref mem [0xde000000-0xde0fffff]
[ 0.231685] pci_bus 0000:09: resource 0 io: [0x5000-0x5fff]
[ 0.231689] pci_bus 0000:09: resource 1 mem: [0xde900000-0xdfffffff]
[ 0.231692] pci_bus 0000:09: resource 2 pref mem [0x80200000-0x802fffff]
[ 0.231696] pci_bus 0000:09: resource 3 io: [0x00-0xffff]
[ 0.231699] pci_bus 0000:09: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.231738] NET: Registered protocol family 2
[ 0.231853] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.232253] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.232748] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.233001] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.233005] TCP reno registered
[ 0.233091] NET: Registered protocol family 1
[ 0.233249] pci 0000:01:00.0: rerouting interrupts for [8086:0330]
[ 0.233255] pci 0000:01:00.2: rerouting interrupts for [8086:0332]
[ 0.233265] pci 0000:06:00.0: rerouting interrupts for [8086:0329]
[ 0.233270] pci 0000:06:00.2: rerouting interrupts for [8086:032a]
[ 0.233279] pci 0000:09:05.0: Boot video device
[ 0.233344] Unpacking initramfs...
[ 0.560025] Freeing initrd memory: 9331k freed
[ 0.566112] Simple Boot Flag at 0x5c set to 0x1
[ 0.566490] audit: initializing netlink socket (disabled)
[ 0.566507] type=2000 audit(1308769914.563:1): initialized
[ 0.570371] highmem bounce pool size: 64 pages
[ 0.570379] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.572248] VFS: Disk quotas dquot_6.5.2
[ 0.572326] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.572436] msgmni has been set to 1731
[ 0.572718] alg: No test for stdrng (krng)
[ 0.572795] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.572800] io scheduler noop registered
[ 0.572803] io scheduler anticipatory registered
[ 0.572806] io scheduler deadline registered
[ 0.572854] io scheduler cfq registered (default)
[ 0.573024] pcieport 0000:00:02.0: irq 120 for MSI/MSI-X
[ 0.573034] pcieport 0000:00:02.0: setting latency timer to 64
[ 0.573164] pcieport 0000:00:04.0: irq 121 for MSI/MSI-X
[ 0.573173] pcieport 0000:00:04.0: setting latency timer to 64
[ 0.573298] pcieport 0000:00:05.0: irq 122 for MSI/MSI-X
[ 0.573307] pcieport 0000:00:05.0: setting latency timer to 64
[ 0.573436] pcieport 0000:00:06.0: irq 123 for MSI/MSI-X
[ 0.573446] pcieport 0000:00:06.0: setting latency timer to 64
[ 0.573591] aer 0000:00:02.0:pcie02: AER service couldn't init device: no _OSC support
[ 0.573602] aer 0000:00:04.0:pcie02: AER service couldn't init device: no _OSC support
[ 0.573611] aer 0000:00:05.0:pcie02: AER service couldn't init device: no _OSC support
[ 0.573619] aer 0000:00:06.0:pcie02: AER service couldn't init device: no _OSC support
[ 0.573769] isapnp: Scanning for PnP cards...
[ 0.927719] isapnp: No Plug & Play device found
[ 0.929565] Linux agpgart interface v0.103
[ 0.929747] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.929845] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.929945] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.930328] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 0.930474] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.930630] PNP: PS/2 Controller [PNP0303:KEYB] at 0x60,0x64 irq 1
[ 0.930633] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 0.931144] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.931241] mice: PS/2 mouse device common for all mice
[ 0.931296] rtc_cmos 00:04: RTC can wake from S4
[ 0.931346] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 0.931370] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 0.931388] cpuidle: using governor ladder
[ 0.931391] cpuidle: using governor menu
[ 0.931397] No iBFT detected.
[ 0.931870] TCP cubic registered
[ 0.932025] NET: Registered protocol family 10
[ 0.933212] Mobile IPv6
[ 0.933216] NET: Registered protocol family 17
[ 0.933234] Using IPI No-Shortcut mode
[ 0.933321] PM: Resume from disk failed.
[ 0.933336] registered taskstats version 1
[ 0.933798] rtc_cmos 00:04: setting system clock to 2011-06-22 19:11:55 UTC (1308769915)
[ 0.933855] Initalizing network drop monitor service
[ 0.933885] Freeing unused kernel memory: 396k freed
[ 0.934145] Write protecting the kernel text: 2576k
[ 0.934186] Write protecting the kernel read-only data: 924k
[ 0.956784] udev[56]: starting version 164
[ 1.167912] usbcore: registered new interface driver usbfs
[ 1.167979] usbcore: registered new interface driver hub
[ 1.168069] usbcore: registered new device driver usb
[ 1.192830] SCSI subsystem initialized
[ 1.211696] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 1.219754] tg3.c:v3.102 (September 1, 2009)
[ 1.219785] tg3 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.219803] tg3 0000:04:00.0: setting latency timer to 64
[ 1.228063] Floppy drive(s): fd0 is 1.44M
[ 1.228891] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.228941] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 1.228964] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.228970] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.229015] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.229063] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.232957] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[ 1.232978] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xde100000
[ 1.237070] Fusion MPT base driver 3.04.12
[ 1.237075] Copyright (c) 1999-2008 LSI Corporation
[ 1.247158] eth0: Tigon3 [partno(BCM95721) rev 4101] (PCI Express) MAC address 00:19:99:12:e8:fa
[ 1.247165] eth0: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 1.247171] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1]
[ 1.247175] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.247208] tg3 0000:05:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.247219] tg3 0000:05:00.0: setting latency timer to 64
[ 1.249411] FDC 0 is a post-1991 82077
[ 1.249449] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.249496] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.249502] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.249507] usb usb1: Product: EHCI Host Controller
[ 1.249511] usb usb1: Manufacturer: Linux 2.6.32-5-686-bigmem ehci_hcd
[ 1.249515] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.249731] usb usb1: configuration #1 chosen from 1 choice
[ 1.249847] hub 1-0:1.0: USB hub found
[ 1.249861] hub 1-0:1.0: 8 ports detected
[ 1.257923] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 1.257953] megaraid: probe new device 0x1000:0x1960:0x1000:0x0518: bus 8:slot 12:func 0
[ 1.257976] megaraid 0000:08:0c.0: PCI INT A -> GSI 99 (level, low) -> IRQ 99
[ 1.260789] Fusion MPT SPI Host driver 3.04.12
[ 1.260844] mptspi 0000:02:08.0: PCI INT A -> GSI 24 (level, low) -> IRQ 24
[ 1.260958] mptbase: ioc0: Initiating bringup
[ 1.295819] eth1: Tigon3 [partno(BCM95721) rev 4101] (PCI Express) MAC address 00:19:99:12:46:e3
[ 1.295826] eth1: attached PHY is 5750 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 1.295831] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.295836] eth1: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.298565] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.298629] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.298643] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.298650] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.298671] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.298714] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001000
[ 1.298775] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.298781] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.298786] usb usb2: Product: UHCI Host Controller
[ 1.298791] usb usb2: Manufacturer: Linux 2.6.32-5-686-bigmem uhci_hcd
[ 1.298795] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.299205] usb usb2: configuration #1 chosen from 1 choice
[ 1.299273] hub 2-0:1.0: USB hub found
[ 1.299285] hub 2-0:1.0: 2 ports detected
[ 1.299383] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.299395] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.299402] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.299420] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.299730] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001400
[ 1.299792] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.299798] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.299803] usb usb3: Product: UHCI Host Controller
[ 1.299807] usb usb3: Manufacturer: Linux 2.6.32-5-686-bigmem uhci_hcd
[ 1.299812] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.299940] usb usb3: configuration #1 chosen from 1 choice
[ 1.300016] hub 3-0:1.0: USB hub found
[ 1.300030] hub 3-0:1.0: 2 ports detected
[ 1.300122] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.300134] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.300140] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.300159] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.300197] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001800
[ 1.300254] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.300260] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.300266] usb usb4: Product: UHCI Host Controller
[ 1.300272] usb usb4: Manufacturer: Linux 2.6.32-5-686-bigmem uhci_hcd
[ 1.300276] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.300414] usb usb4: configuration #1 chosen from 1 choice
[ 1.300469] hub 4-0:1.0: USB hub found
[ 1.300483] hub 4-0:1.0: 2 ports detected
[ 1.300565] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.300576] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.300581] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.300597] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.300629] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001c00
[ 1.300687] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.300693] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.300697] usb usb5: Product: UHCI Host Controller
[ 1.300702] usb usb5: Manufacturer: Linux 2.6.32-5-686-bigmem uhci_hcd
[ 1.300706] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.300830] usb usb5: configuration #1 chosen from 1 choice
[ 1.300887] hub 5-0:1.0: USB hub found
[ 1.300901] hub 5-0:1.0: 2 ports detected
[ 1.303282] libata version 3.00 loaded.
[ 1.309054] megaraid: fw version:[1F42] bios version:[G302]
[ 1.309587] ata_piix 0000:00:1f.1: version 2.13
[ 1.309610] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.309675] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.309785] scsi0 : ata_piix
[ 1.309927] scsi1 : ata_piix
[ 1.310773] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x2400 irq 14
[ 1.310778] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x2408 irq 15
[ 1.349215] scsi2 : LSI Logic MegaRAID driver
[ 1.349385] aic7xxx 0000:08:0b.0: PCI INT A -> GSI 98 (level, low) -> IRQ 98
[ 1.349437] scsi[2]: scanning scsi channel 0 [Phy 0] for non-raid devices
[ 1.476297] ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-4244N, 1.00, max UDMA/33
[ 1.492209] ata2.00: configured for UDMA/33
[ 1.493139] scsi: waiting for bus probes to complete ...
[ 1.772011] ioc0: LSI53C1030 C0: Capabilities={Initiator}
[ 1.879176] scsi 2:0:8:0: Processor QLogic GEM359 1.10 PQ: 0 ANSI: 2
[ 1.908015] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 2.101640] usb 2-2: New USB device found, idVendor=051d, idProduct=0002
[ 2.101645] usb 2-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 2.101649] usb 2-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:2.4
[ 2.101652] usb 2-2: Manufacturer: American Power Conversion
[ 2.101655] usb 2-2: SerialNumber: CS0533110332
[ 2.101779] usb 2-2: configuration #1 chosen from 1 choice
[ 2.383729] scsi4 : ioc0: LSI53C1030 C0, FwRev=01033000h, Ports=1, MaxQ=222, IRQ=24
[ 2.763728] mptspi 0000:02:08.1: PCI INT B -> GSI 25 (level, low) -> IRQ 25
[ 2.763844] mptbase: ioc1: Initiating bringup
[ 3.137405] scsi[2]: scanning scsi channel 1 [Phy 1] for non-raid devices
[ 3.352015] usb 3-2: new low speed USB device using uhci_hcd and address 2
[ 3.509369] usb 3-2: New USB device found, idVendor=0566, idProduct=3107
[ 3.509374] usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.509491] usb 3-2: configuration #1 chosen from 1 choice
[ 3.523553] usbcore: registered new interface driver hiddev
[ 3.657521] scsi 2:1:8:0: Processor QLogic GEM359 1.10 PQ: 0 ANSI: 2
[ 4.304013] ioc1: LSI53C1030 C0: Capabilities={Initiator}
[ 4.914717] scsi5 : ioc1: LSI53C1030 C0, FwRev=01033000h, Ports=1, MaxQ=222, IRQ=25
[ 4.922645] scsi[2]: scanning scsi channel 2 [virtual] for logical drives
[ 4.923086] scsi 2:2:0:0: Direct-Access MegaRAID LD 0 RAID5 1537G 1F42 PQ: 0 ANSI: 2
[ 4.933000] scsi 1:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4244N 1.00 PQ: 0 ANSI: 5
[ 4.951976] sd 2:2:0:0: [sda] 3149414400 512-byte logical blocks: (1.61 TB/1.46 TiB)
[ 4.952030] sd 2:2:0:0: [sda] Write Protect is off
[ 4.952037] sd 2:2:0:0: [sda] Mode Sense: 00 00 00 00
[ 4.952059] sd 2:2:0:0: [sda] Asking for cache data failed
[ 4.952110] sd 2:2:0:0: [sda] Assuming drive cache: write through
[ 4.952399] sd 2:2:0:0: [sda] Asking for cache data failed
[ 4.952449] sd 2:2:0:0: [sda] Assuming drive cache: write through
[ 4.952498] sda: sda1 sda2 sda3
[ 4.954137] sd 2:2:0:0: [sda] Asking for cache data failed
[ 4.954185] sd 2:2:0:0: [sda] Assuming drive cache: write through
[ 4.954234] sd 2:2:0:0: [sda] Attached SCSI disk
[ 4.955220] scsi 2:0:8:0: Attached scsi generic sg0 type 3
[ 4.955983] scsi 2:1:8:0: Attached scsi generic sg1 type 3
[ 4.956110] sd 2:2:0:0: Attached scsi generic sg2 type 0
[ 4.956221] scsi 1:0:0:0: Attached scsi generic sg3 type 5
[ 4.977402] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 4.977408] Uniform CD-ROM driver Revision: 3.20
[ 4.977565] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 6.042075] generic-usb 0003:051D:0002.0001: hiddev0,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:2.4] on usb-0000:00:1d.0-2/input0
[ 6.055202] input: HID 0566:3107 as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input0
[ 6.055273] generic-usb 0003:0566:3107.0002: input,hidraw1: USB HID v1.10 Keyboard [HID 0566:3107] on usb-0000:00:1d.1-2/input0
[ 6.079030] input: HID 0566:3107 as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.1/input/input1
[ 6.079105] generic-usb 0003:0566:3107.0003: input,hidraw2: USB HID v1.10 Device [HID 0566:3107] on usb-0000:00:1d.1-2/input1
[ 6.079145] usbcore: registered new interface driver usbhid
[ 6.079151] usbhid: v2.6:USB HID core driver
[ 6.354966] scsi 4:0:1:0: Direct-Access LSILOGIC 1030 IM 1000 PQ: 0 ANSI: 2
[ 7.356235] scsi 4:0:8:0: Processor SDR GEM318P 1 PQ: 0 ANSI: 2
[ 7.356250] scsi target4:0:8: Beginning Domain Validation
[ 7.357758] scsi target4:0:8: Ending Domain Validation
[ 7.357815] scsi target4:0:8: asynchronous
[ 9.118701] scsi 4:1:1:0: Direct-Access FUJITSU MAW3147NC 5203 PQ: 0 ANSI: 3
[ 9.119654] mptbase: ioc0: RAID STATUS CHANGE for VolumeID 1
[ 9.119658] mptbase: ioc0: volume is now optimal, enabled, quiesced
[ 9.119983] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 0 id=1
[ 9.119986] mptbase: ioc0: PhysDisk is now online, quiesced
[ 9.120298] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 1 id=1
[ 9.120301] mptbase: ioc0: PhysDisk is now online, quiesced
[ 9.120374] scsi target4:1:1: Beginning Domain Validation
[ 9.429888] scsi target4:1:1: Ending Domain Validation
[ 9.430763] mptbase: ioc0: RAID STATUS CHANGE for VolumeID 1
[ 9.430767] mptbase: ioc0: volume is now optimal, enabled
[ 9.431091] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 0 id=1
[ 9.431094] mptbase: ioc0: PhysDisk is now online
[ 9.431403] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 1 id=1
[ 9.431407] mptbase: ioc0: PhysDisk is now online
[ 9.432067] scsi target4:1:1: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI WRFLOW PCOMP (6.25 ns, offset 127)
[ 9.436143] scsi 4:1:4:0: Direct-Access FUJITSU MAW3147NC 5203 PQ: 0 ANSI: 3
[ 9.437095] mptbase: ioc0: RAID STATUS CHANGE for VolumeID 1
[ 9.437100] mptbase: ioc0: volume is now optimal, enabled, quiesced
[ 9.437425] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 0 id=1
[ 9.437429] mptbase: ioc0: PhysDisk is now online, quiesced
[ 9.437738] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 1 id=1
[ 9.437741] mptbase: ioc0: PhysDisk is now online, quiesced
[ 9.437818] scsi target4:1:4: Beginning Domain Validation
[ 9.751279] scsi target4:1:4: Ending Domain Validation
[ 9.752153] mptbase: ioc0: RAID STATUS CHANGE for VolumeID 1
[ 9.752157] mptbase: ioc0: volume is now optimal, enabled
[ 9.752480] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 0 id=1
[ 9.752483] mptbase: ioc0: PhysDisk is now online
[ 9.752794] mptbase: ioc0: RAID STATUS CHANGE for PhysDisk 1 id=1
[ 9.752797] mptbase: ioc0: PhysDisk is now online
[ 9.753454] scsi target4:1:4: FAST-160 WIDE SCSI 320.0 MB/s DT IU RTI WRFLOW PCOMP (6.25 ns, offset 127)
[ 9.754485] sd 4:0:1:0: Attached scsi generic sg4 type 0
[ 9.754941] scsi 4:0:8:0: Attached scsi generic sg5 type 3
[ 9.755253] scsi 4:1:1:0: Attached scsi generic sg6 type 0
[ 9.755555] scsi 4:1:4:0: Attached scsi generic sg7 type 0
[ 9.762209] sd 4:0:1:0: [sdb] 286310400 512-byte logical blocks: (146 GB/136 GiB)
[ 9.763346] sd 4:0:1:0: [sdb] Write Protect is off
[ 9.763354] sd 4:0:1:0: [sdb] Mode Sense: 03 00 00 08
[ 9.764552] sd 4:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 9.765711] sdb: sdb1 sdb2 sdb3
[ 9.779050] sd 4:0:1:0: [sdb] Attached SCSI disk
[ 16.560022] scsi3 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 16.560025] <Adaptec 29160 Ultra160 SCSI adapter>
[ 16.560027] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 16.560029]
[ 16.598369] scsi 3:0:0:0: Medium Changer EXABYTE Exabyte 221L 3.6 PQ: 0 ANSI: 2
[ 16.598390] scsi target3:0:0: Beginning Domain Validation
[ 16.609123] device-mapper: uevent: version 1.0.3
[ 16.609341] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 16.635992] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 16.635997] EXT3-fs: write access will be enabled during recovery.
[ 16.713783] scsi target3:0:0: Ending Domain Validation
[ 16.754551] scsi 3:0:1:0: Sequential-Access IBM ULTRIUM-TD3 54K1 PQ: 0 ANSI: 3
[ 16.754557] scsi 3:0:1:0: Information Units disabled by blacklist
[ 16.754567] scsi target3:0:1: Beginning Domain Validation
[ 16.759810] scsi target3:0:1: wide asynchronous
[ 16.763947] scsi target3:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 127)
[ 16.782694] scsi target3:0:1: Domain Validation skipping write tests
[ 16.782698] scsi target3:0:1: Ending Domain Validation
[ 16.818800] kjournald starting. Commit interval 5 seconds
[ 16.818811] EXT3-fs: recovery complete.
[ 16.830972] EXT3-fs: mounted filesystem with ordered data mode.
[ 17.512399] udev[391]: starting version 164
[ 17.706292] processor LNXCPU:00: registered as cooling_device0
[ 17.706408] processor LNXCPU:02: registered as cooling_device1
[ 17.769109] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 17.769123] ACPI: Power Button [PWRB]
[ 17.769291] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 17.769300] ACPI: Power Button [PWRF]
[ 17.770910] EDAC MC: Ver: 2.1.0 May 18 2011
[ 17.791013] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 17.828952] shpchp 0000:06:00.0: HPC vendor_id 8086 device_id 329 ss_vid 0 ss_did 0
[ 17.829051] shpchp 0000:06:00.0: Can't get msi for the hotplug controller
[ 17.829057] shpchp 0000:06:00.0: Use INTx for the hotplug controller
[ 17.836673] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 17.837044] Contact your BIOS vendor to see if the E752x error registers can be safely un-hidden
[ 17.847263] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 17.853426] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 17.885084] intel_rng: FWH not detected
[ 17.940737] parport_pc 00:09: reported by Plug and Play ACPI
[ 17.940767] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
[ 18.109099] Error: Driver 'pcspkr' is already registered, aborting...
[ 19.767352] Adding 6610736k swap on /dev/sdb3. Priority:-1 extents:1 across:6610736k
[ 19.899065] EXT3 FS on sdb1, internal journal
[ 19.984810] Fusion MPT misc device (ioctl) driver 3.04.12
[ 19.985093] mptctl: Registered with Fusion MPT base driver
[ 19.985100] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 20.003522] ipmi message handler version 39.2
[ 20.012174] IPMI System Interface driver.
[ 20.012183] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x24, irq 0
[ 20.116753] scsi 3:0:0:0: Attached scsi generic sg8 type 8
[ 20.116982] scsi 3:0:1:0: Attached scsi generic sg9 type 1
[ 20.148035] SCSI Media Changer driver v0.25
[ 20.152644] st: Version 20081215, fixed bufsize 32768, s/g segs 256
[ 20.173246] ch0: type #1 (mt): 0x56+1 [medium transport]
[ 20.173252] ch0: type #2 (st): 0x1+21 [storage]
[ 20.173256] ch0: type #3 (ie): 0x51+1 [import/export]
[ 20.173260] ch0: type #4 (dt): 0x52+1 [data transfer]
[ 20.190212] ch0: dt 0x52: not this SCSI bus
[ 20.190216] ch0: INITIALIZE ELEMENT STATUS, may take some time ...
[ 20.234839] ipmi: Found new BMC (man_id: 0x002880, prod_id: 0x0000, dev_id: 0x00)
[ 20.234856] IPMI kcs interface initialized
[ 20.239501] ipmi device interface
[ 20.389194] smsc47m1: Found SMSC LPC47M10x/LPC47M112/LPC47M13x
[ 20.389255] ACPI: I/O resource smsc47m1 [0x800-0x87f] conflicts with ACPI region SSWC [0x800-0x87f]
[ 20.389328] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 21.427861] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 21.429511] SGI XFS Quota Management subsystem
[ 21.452147] XFS mounting filesystem dm-1
[ 21.611144] Starting XFS recovery on filesystem: dm-1 (logdev: internal)
[ 21.718630] Ending XFS recovery on filesystem: dm-1 (logdev: internal)
[ 21.729198] kjournald starting. Commit interval 5 seconds
[ 21.739241] EXT3 FS on sdb2, internal journal
[ 21.739249] EXT3-fs: mounted filesystem with ordered data mode.
[ 21.760004] XFS mounting filesystem dm-13
[ 21.923463] Starting XFS recovery on filesystem: dm-13 (logdev: internal)
[ 22.538960] Ending XFS recovery on filesystem: dm-13 (logdev: internal)
[ 22.564746] XFS mounting filesystem dm-5
[ 22.715031] Starting XFS recovery on filesystem: dm-5 (logdev: internal)
[ 22.830002] Ending XFS recovery on filesystem: dm-5 (logdev: internal)
[ 22.846361] XFS mounting filesystem dm-9
[ 23.008757] Starting XFS recovery on filesystem: dm-9 (logdev: internal)
[ 23.577439] Ending XFS recovery on filesystem: dm-9 (logdev: internal)
[ 23.591006] XFS mounting filesystem dm-16
[ 23.715030] Starting XFS recovery on filesystem: dm-16 (logdev: internal)
[ 23.899097] Ending XFS recovery on filesystem: dm-16 (logdev: internal)
[ 23.919574] kjournald starting. Commit interval 5 seconds
[ 23.928215] EXT3 FS on dm-17, internal journal
[ 23.928223] EXT3-fs: mounted filesystem with ordered data mode.
[ 24.659925] ADDRCONF(NETDEV_UP): siemens: link is not ready
[ 25.320087] ADDRCONF(NETDEV_UP): snt: link is not ready
[ 25.922429] microcode: CPU0 sig=0xf43, pf=0x1, revision=0x5
[ 25.922439] platform microcode: firmware: requesting intel-ucode/0f-04-03
[ 25.949676] microcode: CPU1 sig=0xf43, pf=0x1, revision=0x5
[ 25.949687] platform microcode: firmware: requesting intel-ucode/0f-04-03
[ 25.953616] Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 26.296170] tg3: siemens: Link is up at 100 Mbps, full duplex.
[ 26.296174] tg3: siemens: Flow control is on for TX and on for RX.
[ 26.296333] ADDRCONF(NETDEV_CHANGE): siemens: link becomes ready
[ 27.003373] tg3: snt: Link is up at 100 Mbps, full duplex.
[ 27.003377] tg3: snt: Flow control is on for TX and on for RX.
[ 27.003522] ADDRCONF(NETDEV_CHANGE): snt: link becomes ready
[ 29.168045] usb 2-2: USB disconnect, address 2
[ 29.171446] /tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/hid/usbhid/hid-core.c: usb_submit_urb(ctrl) failed
[ 33.620033] usb 2-2: new low speed USB device using uhci_hcd and address 3
[ 33.813959] usb 2-2: New USB device found, idVendor=051d, idProduct=0002
[ 33.813965] usb 2-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 33.813970] usb 2-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:2.4
[ 33.813974] usb 2-2: Manufacturer: American Power Conversion
[ 33.813977] usb 2-2: SerialNumber: CS0533110332
[ 33.814127] usb 2-2: configuration #1 chosen from 1 choice
[ 36.147735] generic-usb 0003:051D:0002.0004: hiddev0,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:2.4] on usb-0000:00:1d.0-2/input0
[ 37.149006] siemens: no IPv6 routers present
[ 37.245005] snt: no IPv6 routers present
[ 38.345062] usb 2-2: USB disconnect, address 3
[ 42.745031] usb 2-2: new low speed USB device using uhci_hcd and address 4
[ 42.938593] usb 2-2: New USB device found, idVendor=051d, idProduct=0002
[ 42.938599] usb 2-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 42.938603] usb 2-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:2.4
[ 42.938607] usb 2-2: Manufacturer: American Power Conversion
[ 42.938610] usb 2-2: SerialNumber: CS0533110332
[ 42.938754] usb 2-2: configuration #1 chosen from 1 choice
[ 45.380361] generic-usb 0003:051D:0002.0005: hiddev0,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:2.4] on usb-0000:00:1d.0-2/input0
[ 48.268044] usb 2-2: USB disconnect, address 4
[ 48.269572] /tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/hid/usbhid/hid-core.c: usb_submit_urb(ctrl) failed
[ 48.731053] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 48.731193] IP: [<f843db27>] hiddev_ioctl+0x26/0x56f [usbhid]
[ 48.731294] *pdpt = 000000003587c001 *pde = 0000000000000000
[ 48.731424] Oops: 0000 [#1] SMP
[ 48.731549] last sysfs file: /sys/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/0003:051D:0002.0005/hidraw/hidraw0/uevent
[ 48.731619] Modules linked in: microcode xfs exportfs eeprom ipmi_devintf st(+) ch(+) ipmi_si ipmi_msghandler mptctl psmouse dm_snapshot snd_pcm snd_timer parport_pc snd soundcore snd_page_alloc parport i2c_i801 pcspkr e752x_edac shpchp joydev evdev serio_raw container i2c_core rng_core pci_hotplug button edac_core processor ext3 jbd mbcache dm_mod sr_mod cdrom sg sd_mod crc_t10dif ata_generic usbhid hid aic7xxx ata_piix uhci_hcd libata mptspi megaraid_mbox mptscsih mptbase ehci_hcd floppy tg3 megaraid_mm scsi_transport_spi libphy thermal thermal_sys scsi_mod usbcore nls_base [last unloaded: scsi_wait_scan]
[ 48.734244]
[ 48.734295] Pid: 1390, comm: apcupsd Not tainted (2.6.32-5-686-bigmem #1) D1889
[ 48.734361] EIP: 0060:[<f843db27>] EFLAGS: 00010286 CPU: 0
[ 48.734419] EIP is at hiddev_ioctl+0x26/0x56f [usbhid]
[ 48.734473] EAX: 00000000 EBX: 400c4807 ECX: bffb50d4 EDX: fffffffb
[ 48.734528] ESI: f65dd5c0 EDI: f645a000 EBP: bffb50d4 ESP: f5f8bea0
[ 48.734584] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[ 48.734639] Process apcupsd (pid: 1390, ti=f5f8a000 task=f5dc1100 task.ti=f5f8a000)
[ 48.734703] Stack:
[ 48.734752] c1031658 f5b20000 c143de20 f5ff9e00 c2608e20 f5ff9e00 c127e933 c13a4ba0
[ 48.735023] <0> c143959c c143de20 c143de20 c1439354 f5dc12bc c2608e20 00000000 00000000
[ 48.735023] <0> 00000296 00000292 0000c350 f5dc1100 c26045cc f5f8bf44 c104d131 f5f8bf44
[ 48.735023] Call Trace:
[ 48.735023] [<c1031658>] ? finish_task_switch+0x34/0x95
[ 48.735023] [<c127e933>] ? schedule+0x7a4/0x7f1
[ 48.735023] [<c104d131>] ? lock_hrtimer_base+0x15/0x2f
[ 48.735023] [<c104d1af>] ? hrtimer_try_to_cancel+0x2f/0x35
[ 48.735023] [<c104d1bf>] ? hrtimer_cancel+0xa/0x14
[ 48.735023] [<f843db01>] ? hiddev_ioctl+0x0/0x56f [usbhid]
[ 48.735023] [<c10c53d4>] ? vfs_ioctl+0x1c/0x5f
[ 48.735023] [<c10c5968>] ? do_vfs_ioctl+0x4aa/0x4e5
[ 48.735023] [<c104cae6>] ? hrtimer_wakeup+0x0/0x18
[ 48.735023] [<c10517e0>] ? getnstimeofday+0x4d/0xc9
[ 48.735023] [<c1051896>] ? do_gettimeofday+0xf/0x29
[ 48.735023] [<c10c59e4>] ? sys_ioctl+0x41/0x58
[ 48.735023] [<c100813b>] ? sysenter_do_call+0x12/0x28
[ 48.735023] Code: 5b 5e 5f 5d c3 55 89 cd 57 56 53 89 d3 83 ec 7c 8b 40 70 ba fb ff ff ff 89 44 24 04 8b b0 10 c0 00 00 8b 7e 28 8b 87 54 0c 00 00 <8b> 08 8b 87 a0 0e 00 00 89 04 24 83 3e 00 0f 84 2b 05 00 00 81
[ 48.735023] EIP: [<f843db27>] hiddev_ioctl+0x26/0x56f [usbhid] SS:ESP 0068:f5f8bea0
[ 48.735023] CR2: 0000000000000000
[ 48.739373] ---[ end trace 650ff9964d1a683e ]---
[ 52.796015] usb 2-2: new low speed USB device using uhci_hcd and address 5
[ 52.990953] usb 2-2: New USB device found, idVendor=051d, idProduct=0002
[ 52.991011] usb 2-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 52.991072] usb 2-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:2.4
[ 52.991128] usb 2-2: Manufacturer: American Power Conversion
[ 52.991182] usb 2-2: SerialNumber: CS0533110332
[ 52.991366] usb 2-2: configuration #1 chosen from 1 choice
[ 55.475708] generic-usb 0003:051D:0002.0006: hiddev0,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:2.4] on usb-0000:00:1d.0-2/input0
[ 57.441037] usb 2-2: USB disconnect, address 5
[ 61.904022] usb 2-2: new low speed USB device using uhci_hcd and address 6
[ 62.098960] usb 2-2: New USB device found, idVendor=051d, idProduct=0002
[ 62.099021] usb 2-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 62.099081] usb 2-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:2.4
[ 62.099137] usb 2-2: Manufacturer: American Power Conversion
[ 62.099192] usb 2-2: SerialNumber: CS0533110332
[ 62.099380] usb 2-2: configuration #1 chosen from 1 choice
[ 64.651753] generic-usb 0003:051D:0002.0007: hiddev0,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:2.4] on usb-0000:00:1d.0-2/input0
[ 66.121039] usb 2-2: USB disconnect, address 6
[ 70.648015] usb 2-2: new low speed USB device using uhci_hcd and address 7
[ 70.842961] usb 2-2: New USB device found, idVendor=051d, idProduct=0002
[ 70.843022] usb 2-2: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 70.843085] usb 2-2: Product: Smart-UPS 3000 RM FW:666.6.I USB FW:2.4
[ 70.843142] usb 2-2: Manufacturer: American Power Conversion
[ 70.843196] usb 2-2: SerialNumber: CS0533110332
[ 70.843378] usb 2-2: configuration #1 chosen from 1 choice
[ 71.970369] ch0: ... finished
[ 71.970426] ch 3:0:0:0: Attached scsi changer ch0
[ 71.970990] st 3:0:1:0: Attached scsi tape st0
[ 71.971050] st 3:0:1:0: st0: try direct i/o: yes (alignment 4 B)
[ 71.981346] osst :I: Tape driver with OnStream support version 0.99.4
[ 71.981350] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[ 73.219800] generic-usb 0003:051D:0002.0008: hiddev0,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 3000 RM FW:666.6.I USB FW:2.4] on usb-0000:00:1d.0-2/input0
[ 79.173263] vboxdrv: Found 2 processor cores.
[ 79.173442] vboxdrv: fAsync=0 offMin=0x4a8 offMax=0x179d
[ 79.173580] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 79.173650] vboxdrv: Successfully loaded version 3.2.12 (interface 0x00140001).
Reply to: