Bug#628650: linux-image-2.6.32-5-amd64: dd fails with ASC-1045 SAS controller and LTO-4
Package: linux-2.6
Version: 2.6.32-34squeeze1
Severity: normal
I have a Quantum LTO-4 tape drive connected to an ASC-1045 controller. The kernel logs included do show the nature of the problem I have encountered.
I am writing data to / from the tape drive using dd, like so:
dd if=/dev/nst0 of=file bs=32K
This causes the messages you see below. The tape drive will become unusable, and I have no choice but to do a cold boot to restore access to the
device, otherwise I get "device busy" messages. I have attempted to use the "official" adaptec drivers for this card, and get the same result as
when I use mvsas. I am not sure if this problem is a hardware issue (I suspect not, since sometimes things work) or a software issue. I am able to
send some data to the tape drive, and read some data... the problem has been very difficult for me to narrow down.
The information attached to this particular bug report comes from an attempt to use the Adaptec driver, which is not part of Debian, but identical
messages are generated with the mvsas module.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-34squeeze1) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed May 18 23:13:22 UTC 2011
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-amd64 root=/dev/mapper/virtualmachines-virtualserver--root ro quiet
** Not tainted
** Kernel log:
[ 482.176432] [<ffffffffa0036671>] ? scsi_init_sgtable+0x3f/0x5a [scsi_mod]
[ 482.176438] [<ffffffff812fb3b5>] ? schedule_timeout+0x2e/0xdd
[ 482.176443] [<ffffffff8117ecde>] ? blk_peek_request+0x18b/0x19f
[ 482.176446] [<ffffffff812fb26c>] ? wait_for_common+0xde/0x15b
[ 482.176453] [<ffffffff8104a440>] ? default_wake_function+0x0/0x9
[ 482.176456] [<ffffffffa013a079>] ? st_do_scsi+0x2c4/0x2f4 [st]
[ 482.176460] [<ffffffffa013d5b2>] ? st_read+0x38a/0x8cf [st]
[ 482.176465] [<ffffffff810ef538>] ? vfs_read+0xa6/0xff
[ 482.176467] [<ffffffff810ef64d>] ? sys_read+0x45/0x6e
[ 482.176471] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 602.176047] INFO: task dd:2388 blocked for more than 120 seconds.
[ 602.176165] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 602.176318] dd D ffff88081d2bd4c0 0 2388 2387 0x00000000
[ 602.176321] ffff88081d2bd4c0 0000000000000086 0000000000000000 ffffffff8118314f
[ 602.176325] 0000008000000020 0000000000000fe0 000000000000f9e0 ffff88081cb31fd8
[ 602.176328] 0000000000015780 0000000000015780 ffff88081d2bdbd0 ffff88081d2bdec8
[ 602.176331] Call Trace:
[ 602.176337] [<ffffffff8118314f>] ? blk_rq_map_sg+0x140/0x289
[ 602.176349] [<ffffffffa0036671>] ? scsi_init_sgtable+0x3f/0x5a [scsi_mod]
[ 602.176353] [<ffffffff812fb3b5>] ? schedule_timeout+0x2e/0xdd
[ 602.176357] [<ffffffff8117ecde>] ? blk_peek_request+0x18b/0x19f
[ 602.176359] [<ffffffff812fb26c>] ? wait_for_common+0xde/0x15b
[ 602.176364] [<ffffffff8104a440>] ? default_wake_function+0x0/0x9
[ 602.176367] [<ffffffffa013a079>] ? st_do_scsi+0x2c4/0x2f4 [st]
[ 602.176371] [<ffffffffa013d5b2>] ? st_read+0x38a/0x8cf [st]
[ 602.176374] [<ffffffff810ef538>] ? vfs_read+0xa6/0xff
[ 602.176377] [<ffffffff810ef64d>] ? sys_read+0x45/0x6e
[ 602.176380] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 722.176069] INFO: task dd:2388 blocked for more than 120 seconds.
[ 722.176188] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 722.176341] dd D ffff88081d2bd4c0 0 2388 1 0x00000004
[ 722.176346] ffff88081d2bd4c0 0000000000000086 0000000000000000 ffffffff8118314f
[ 722.176349] 0000008000000020 0000000000000fe0 000000000000f9e0 ffff88081cb31fd8
[ 722.176352] 0000000000015780 0000000000015780 ffff88081d2bdbd0 ffff88081d2bdec8
[ 722.176355] Call Trace:
[ 722.176363] [<ffffffff8118314f>] ? blk_rq_map_sg+0x140/0x289
[ 722.176379] [<ffffffffa0036671>] ? scsi_init_sgtable+0x3f/0x5a [scsi_mod]
[ 722.176385] [<ffffffff812fb3b5>] ? schedule_timeout+0x2e/0xdd
[ 722.176389] [<ffffffff8117ecde>] ? blk_peek_request+0x18b/0x19f
[ 722.176392] [<ffffffff812fb26c>] ? wait_for_common+0xde/0x15b
[ 722.176397] [<ffffffff8104a440>] ? default_wake_function+0x0/0x9
[ 722.176401] [<ffffffffa013a079>] ? st_do_scsi+0x2c4/0x2f4 [st]
[ 722.176404] [<ffffffffa013d5b2>] ? st_read+0x38a/0x8cf [st]
[ 722.176409] [<ffffffff810ef538>] ? vfs_read+0xa6/0xff
[ 722.176412] [<ffffffff810ef64d>] ? sys_read+0x45/0x6e
[ 722.176415] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 842.176106] INFO: task dd:2388 blocked for more than 120 seconds.
[ 842.176225] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 842.176378] dd D ffff88081d2bd4c0 0 2388 1 0x00000004
[ 842.176383] ffff88081d2bd4c0 0000000000000086 0000000000000000 ffffffff8118314f
[ 842.176387] 0000008000000020 0000000000000fe0 000000000000f9e0 ffff88081cb31fd8
[ 842.176390] 0000000000015780 0000000000015780 ffff88081d2bdbd0 ffff88081d2bdec8
[ 842.176393] Call Trace:
[ 842.176402] [<ffffffff8118314f>] ? blk_rq_map_sg+0x140/0x289
[ 842.176423] [<ffffffffa0036671>] ? scsi_init_sgtable+0x3f/0x5a [scsi_mod]
[ 842.176429] [<ffffffff812fb3b5>] ? schedule_timeout+0x2e/0xdd
[ 842.176433] [<ffffffff8117ecde>] ? blk_peek_request+0x18b/0x19f
[ 842.176436] [<ffffffff812fb26c>] ? wait_for_common+0xde/0x15b
[ 842.176442] [<ffffffff8104a440>] ? default_wake_function+0x0/0x9
[ 842.176446] [<ffffffffa013a079>] ? st_do_scsi+0x2c4/0x2f4 [st]
[ 842.176449] [<ffffffffa013d5b2>] ? st_read+0x38a/0x8cf [st]
[ 842.176454] [<ffffffff810ef538>] ? vfs_read+0xa6/0xff
[ 842.176457] [<ffffffff810ef64d>] ? sys_read+0x45/0x6e
[ 842.176460] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 962.176123] INFO: task dd:2388 blocked for more than 120 seconds.
[ 962.176242] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 962.176395] dd D ffff88081d2bd4c0 0 2388 1 0x00000004
[ 962.176400] ffff88081d2bd4c0 0000000000000086 0000000000000000 ffffffff8118314f
[ 962.176404] 0000008000000020 0000000000000fe0 000000000000f9e0 ffff88081cb31fd8
[ 962.176407] 0000000000015780 0000000000015780 ffff88081d2bdbd0 ffff88081d2bdec8
[ 962.176410] Call Trace:
[ 962.176420] [<ffffffff8118314f>] ? blk_rq_map_sg+0x140/0x289
[ 962.176443] [<ffffffffa0036671>] ? scsi_init_sgtable+0x3f/0x5a [scsi_mod]
[ 962.176449] [<ffffffff812fb3b5>] ? schedule_timeout+0x2e/0xdd
[ 962.176453] [<ffffffff8117ecde>] ? blk_peek_request+0x18b/0x19f
[ 962.176456] [<ffffffff812fb26c>] ? wait_for_common+0xde/0x15b
[ 962.176462] [<ffffffff8104a440>] ? default_wake_function+0x0/0x9
[ 962.176466] [<ffffffffa013a079>] ? st_do_scsi+0x2c4/0x2f4 [st]
[ 962.176469] [<ffffffffa013d5b2>] ? st_read+0x38a/0x8cf [st]
[ 962.176474] [<ffffffff810ef538>] ? vfs_read+0xa6/0xff
[ 962.176477] [<ffffffff810ef64d>] ? sys_read+0x45/0x6e
[ 962.176481] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
[ 1082.176075] INFO: task dd:2388 blocked for more than 120 seconds.
[ 1082.176194] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1082.176347] dd D ffff88081d2bd4c0 0 2388 1 0x00000004
[ 1082.176351] ffff88081d2bd4c0 0000000000000086 0000000000000000 ffffffff8118314f
[ 1082.176355] 0000008000000020 0000000000000fe0 000000000000f9e0 ffff88081cb31fd8
[ 1082.176358] 0000000000015780 0000000000015780 ffff88081d2bdbd0 ffff88081d2bdec8
[ 1082.176361] Call Trace:
[ 1082.176370] [<ffffffff8118314f>] ? blk_rq_map_sg+0x140/0x289
[ 1082.176390] [<ffffffffa0036671>] ? scsi_init_sgtable+0x3f/0x5a [scsi_mod]
[ 1082.176396] [<ffffffff812fb3b5>] ? schedule_timeout+0x2e/0xdd
[ 1082.176401] [<ffffffff8117ecde>] ? blk_peek_request+0x18b/0x19f
[ 1082.176404] [<ffffffff812fb26c>] ? wait_for_common+0xde/0x15b
[ 1082.176410] [<ffffffff8104a440>] ? default_wake_function+0x0/0x9
[ 1082.176413] [<ffffffffa013a079>] ? st_do_scsi+0x2c4/0x2f4 [st]
[ 1082.176417] [<ffffffffa013d5b2>] ? st_read+0x38a/0x8cf [st]
[ 1082.176422] [<ffffffff810ef538>] ? vfs_read+0xa6/0xff
[ 1082.176425] [<ffffffff810ef64d>] ? sys_read+0x45/0x6e
[ 1082.176428] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b
** Model information
sys_vendor: System manufacturer
product_name: System Product Name
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 0902
board_vendor: ASUSTeK Computer INC.
board_name: KGP(M)E-D16
board_version: Rev 1.xxG
** Loaded modules:
Module Size Used by
st 30916 2
asc1xx5 31081 1
ip6table_filter 2384 0
ip6_tables 15107 1 ip6table_filter
ebtable_nat 1588 0
ebtables 13933 1 ebtable_nat
ipt_REJECT 1953 2
xt_tcpudp 2319 4
iptable_filter 2258 1
ip_tables 13915 1 iptable_filter
x_tables 12845 5 ip6_tables,ebtables,ipt_REJECT,xt_tcpudp,ip_tables
kvm_amd 31862 0
kvm 214152 1 kvm_amd
fuse 50940 1
bridge 39662 0
stp 1440 1 bridge
ext2 52937 1
loop 11799 0
firewire_sbp2 11530 0
snd_pcm 60503 0
snd_timer 15582 1 snd_pcm
snd 46542 2 snd_pcm,snd_timer
soundcore 4598 1 snd
snd_page_alloc 6265 1 snd_pcm
osst 45333 0
k10temp 2715 0
i2c_piix4 8328 0
edac_core 29261 0
i2c_core 15835 1 i2c_piix4
edac_mce_amd 6449 0
evdev 7352 3
joydev 8459 0
pcspkr 1699 0
container 2389 0
button 4650 0
processor 29951 0
ext4 288478 2
mbcache 5050 2 ext2,ext4
jbd2 67079 1 ext4
crc16 1319 1 ext4
dm_mod 53754 9
sg 24085 0
sr_mod 12602 0
firewire_ohci 19692 0
cdrom 29415 1 sr_mod
ses 5144 0
sd_mod 29937 4
enclosure 5519 1 ses
crc_t10dif 1276 1 sd_mod
ata_generic 3047 0
usbhid 33324 0
hid 63273 1 usbhid
ahci 32534 0
ohci_hcd 19359 0
firewire_core 36880 2 firewire_sbp2,firewire_ohci
libsas 35528 1 asc1xx5
ehci_hcd 32129 0
pata_atiixp 3505 0
aacraid 64448 3
usbcore 122450 4 usbhid,ohci_hcd,ehci_hcd
scsi_transport_sas 19881 2 asc1xx5,libsas
crc_itu_t 1307 1 firewire_core
libata 133680 4 ata_generic,ahci,libsas,pata_atiixp
nls_base 6377 1 usbcore
thermal 11674 0
scsi_mod 126597 12 st,asc1xx5,firewire_sbp2,osst,sg,sr_mod,ses,sd_mod,libsas,aacraid,scsi_transport_sas,libata
e1000e 110111 0
thermal_sys 11942 2 processor,thermal
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RD890 Northbridge only dual slot (2x16) PCI-e GFX Hydra part [1002:5a10] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:8448]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Capabilities: <access denied>
00:02.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port B) [1002:5a16] (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Memory behind bridge: fbd00000-fbffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:09.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (PCI express gpp port H) [1002:5a1c] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbc00000-fbcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0a.0 PCI bridge [0604]: ATI Technologies Inc RD890 PCI to PCI bridge (external gfx1 port A) [1002:5a1d] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fbb00000-fbbfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:0c.0 PCI bridge [0604]: ATI Technologies Inc Device [1002:5a20] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fba00000-fbafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [IDE mode] [1002:4390] (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at 9000 [size=4]
Region 2: I/O ports at 8000 [size=8]
Region 3: I/O ports at 7000 [size=4]
Region 4: I/O ports at 6000 [size=16]
Region 5: Memory at faffe400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at faff6000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at faff7000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at faffe800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at faffc000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at faffd000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at faffec00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3d)
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ff00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_atiixp
00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fb000000-fb9fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:844b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fafff000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k10temp
00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:19.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:19.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:19.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:19.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k10temp
00:19.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
01:01.0 VGA compatible controller [0300]: ASPEED Technology, Inc. ASPEED Graphics Family [1a03:2000] (rev 10) (prog-if 00 [VGA controller])
Subsystem: ASPEED Technology, Inc. ASPEED Graphics Family [1a03:2000]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=8M]
Region 1: Memory at fb9c0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at bc00 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
01:02.0 FireWire (IEEE 1394) [0c00]: Agere Systems FW322/323 [11c1:5811] (rev 70) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:8259]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fb9ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
02:00.0 Serial Attached SCSI controller [0107]: Adaptec ASC-1405 Unified Serial HBA [9005:0450] (rev 02)
Subsystem: Marvell Technology Group Ltd. Device [11ab:6440]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 36
Region 2: I/O ports at cc00 [size=128]
Region 4: Memory at fbaff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fba80000 [disabled] [size=256K]
Capabilities: <access denied>
Kernel driver in use: asc1xx5
03:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: ASUSTeK Computer Inc. Device [1043:8369]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at fbbe0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at dc00 [size=32]
Region 3: Memory at fbbdc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: e1000e
04:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: ASUSTeK Computer Inc. Device [1043:8369]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at fbce0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ec00 [size=32]
Region 3: Memory at fbcdc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: e1000e
05:00.0 RAID bus controller [0104]: Adaptec AAC-RAID [9005:0285] (rev 09)
Subsystem: Adaptec ASR-2805 [9005:02d7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 24
Region 0: Memory at fbe00000 (64-bit, non-prefetchable) [size=2M]
Expansion ROM at fbd80000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: aacraid
** USB devices:
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 003: ID 046b:ff10 American Megatrends, Inc.
Bus 003 Device 002: ID 046b:ff01 American Megatrends, Inc.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.1
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.32-5-amd64 (SMP w/12 CPU cores)
Locale: LANG=en_CA.UTF-8, LC_CTYPE=en_CA.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-34squeeze1 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-amd64 recommends:
pn firmware-linux-free <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64: false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64: true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:
Reply to: